flhtk plate relocate

You search Auto repair manual PDF flhtk plate relocate, if there are search results will appear below. If search results do not exist, please search by others keyword.



  flhtk plate relocate Direct Download speed 5282 Kb/s

  flhtk plate relocate Full Version speed 6162 Kb/s



HARLEY DAVIDSON TOURING LAYBACK LICENSE PLATE MOUNTING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-02-2011

download
This kit fits all 1999 and later FLHR (Road King®) models, FLTR (Road Glide®) and FLHT (Electra Glide® standard) models having license plates measuring a maximum of 7-1/4 x 4-1/4 inches (184 x 108 mm). Also fits 2003 FLHRSEI2 (Screamin’ Eagle® Road King). Does not fit with Detachable Tour-Pak Rack, part number 53276-04. Does not fit 2002 FLHRSEI (Screamin’ Eagle Road King). Kit Contents See Figure 1. INSTALLATION 1. Remove the license plate from the vehicle (if installed). Remove the two hex head bolts holding the original equipment (O.E.) license-plate bracket in place. The bolts and license-plate bracket can be discarded. 2. See Figure 1. Install the new layback license plate holder (1) using the button-head hex socket screws (3) from the kit. Tighten the screws to 19 ft-lbs (25.8 Nm) . 4 1 3 7 5 2 6 is02737 1. License plate holder, layback 2. Foam pad (6) 3. Screw, button head, hex socket (2) 4. License plate frame 5. Set screw, socket head (2) 6. Hex key 7. Reflector assembly, Part Number 59365-07 Figure 1. Layback License Plate Mount Components 3. Position the license plate onto the foam pads (2) of the license plate holder, centering and aligning the plate parallel to the holder edges for best appearance. NOTE Slots in the inside top edge of the license plate frame (4) fit over the two tabs on the top edge of the license plate holder. 4. Hook the top of the license plate frame over the top edge of the holder. Swing the bottom edge of the frame inward, holding the license plate in position against the pads. 5. Use the hex key (6) from the kit to securely fasten the license plate frame to the holder with the two socket head set screws (5)

Incoming search terms:

HARLEY DAVIDSON DYNA REAR STOP/ TAIL/ TURN SIGNAL RELOCATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2011

download
PREPARATION NOTE Position the motorcycle upright using a suitable lift or jack. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow instructions to remove the main fuse. 2. Follow the service manual instructions to remove the seat. 3. Raise the rear of the vehicle to allow access to the underside of the rear fender. LICENSE BRACKET AND ILLUMINATOR REMOVAL For Models WITHOUT a Center Tail Lamp NOTE See Figure 1. The reflector mounting block (2) is held to the fender (1) with double sided tape. Remove with care to avoid scratching paint. 1 3 2 5 4 6 7 is06256 1. Rear fender 2. Rear reflector and mounting block 3. Wire channel (2) 4. License plate bracket mount 5.5/16-18 screw (2) 6. License plate illuminator 7. M4 screw (2) Figure 1. Rear Fender, Models Without Center Tail Lamp 1. Remove the rear reflector and mounting block (2) from the underside of the rear fender (1). 2. Remove the license plate from the vehicle (if installed). Retain the plate and attaching hardware. NOTE Before removing rear wiring, note wire routing. -J04856 1 of 10 3. Remove the rear lamp wiring from behind the wire channels (3) on the underside of the fender. 4. Disconnect the two-way license lamp connector [93] and the four-way right [18] and left [19] stop/tail/turn (STT) lamp connectors from the STT module in the area under the seat. 5. Remove the two 5/16-18 screws (5) retaining the license plate bracket mount assembly (4) to the fender support. 6. Remove the license plate illuminator (6) from the license plate bracket mount assembly. Save the illuminator. The bracket mount (4) and four screws (5, 7) can be discarded. 7. Proceed to License Bracket and Illuminator Assembly . For Models WITH a Center Tail Lamp NOTE On these models, the license plate illuminator is part of the center tail lamp and is not removed. 1. Remove the three screws retaining the license plate bracket to the tail lamp housing. Remove the bracket and set aside for later assembly. 2. Proceed to Rear Lamp Wiring, For Models WITH a Center Tail Lamp and RED Stop/Turn Signals or AMBER Turn Signals . LICENSE BRACKET AND ILLUMINATOR ASSEMBLY For Models WITHOUT a Center Tail Lamp 1. See Figure 7. Get the new license plate bracket (3), illuminator cover (4), spacer (6) and two M4 screws (5) from the kit, and the license plate illuminator (A) removed from the original equipment (OE) license plate bracket. 2. See Figure 2. Assemble the illuminator (1), spacer (2) and cover (3) to the license plate bracket (5) in the sequence shown, and tighten the screws (4) securely. 3. Get the STT relocation weldment (6), two screws (7) and two flat washers (8) from the kit. 4. Apply a few drops of Loctite 271 – Red to the clean screw threads. Assemble the license plate bracket to the weldment as shown, and tighten the screws to 120 in-lbs (13.6 N-m) . NOTE If using a metal tool to install the black nuts, protect the finish with cloth or paper to prevent damage. 5. Loosely install the black painted nuts (9) onto the threaded studs on each side of the STT relocation weldment. 6. Remove the wires and socket terminals from the two-way license plate illuminator socket housing. Set the socket housing aside for later installation

BMW Motorcycles R 850/ R 1100 Series and K 1200 RS – New Clutch and Pressure Plate

0

Filed Under (BMW) by admin on 16-11-2010

download
Details: All R 850/R 1100 and K 1200 RS models produced from December 1997 have received a new clutch disc, manufactured by VALEO, and a new pressure plate (see applicable part numbers below). Earlier production for both series can be fitted with the new parts. However, due to changes in specifications (a thicker pressure plate, a thinner clutch disc), the new VALEO clutch disc is not compatible with the old pressure plate. In this application, the new clutch disc and pressure plate must be replaced as a pair. Series Production: R 850/R1100 models: Starting with December 1997 production. K 1200 RS: Starting with December 1997 production. Part Number: R 850/R1100 Models: VALEO Clutch Disc: 21 21 2 325 864 Used only in conjunction with Pressure Plate: 21 21 2 325 863 R 850/R1100 models: VALEO Clutch Disc with reduced play on gearbox input shaft (KD – Scheibe): 21 21 2 325 862 Used only in conjunction with Pressure Plate: 21 21 2 325 863 K 1200 RS: VALEO Clutch Disc: 21 21 2 332 973 Used only in conjunction with Pressure Plate: 21 21 2 332 974 Attention: For R 850/R1100 and K 1200 RS models with production dates of 12/97 and later, all clutch parts can be replaced individually, as the new pressure plate will already be installed. On earlier production examples, installing the new VALEO clutch disc without replacing the pressure plate will not allow the clutch to completely disengage.

HI-4 DUAL FIRE MOTORCYCLE IGNITION INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Turn ignition switch off and disconnect battery ground cable. 2. Refer to Figure 3. Remove OE ignition module and wire harness (items 1-4). You will disconnect two wires at the coil (15), a wire going to the VOES (Vacuum Operated Electrical Switch) (18), a black ground wire at the ignition module, and the 3 pin plug (20) that connects to the sensor plate (11). Refer to shop manual for locations. 3. Remove ignition cover plates and gasket (items 5- 9). This will require drilling out two rivets. The rivets will later be replaced with two supplied self- threading screws. 4. In order to remove the sensor plate cable, the cable plug (20) must be removed first. Use needle nose pliers to pull the terminals out of the plug. Then pull the cable through the exit hole at the bottom of the timing cover. 5. Note location of sensor plate (11). There is a V notch in the sensor plate used for alignment. When you install the HI-4, you should align the V notch in the same location. This should set the timing close enough to start the engine. Remove and save the two standoffs and washers (10). Remove the sensor plate (11). HI-4 INSTALLATION Refer to Figure 4. The HI-4 requires use of the OE timing rotor P/N 32402-83 (used only on 1985 and newer models). If you have an older model or are not sure, check the rotor (9) for the correct part number. For models prior to 1980, use the supplied 10-32 x ¾”bolt and washer to mount the rotor. 1. Install the HI-4 system in place of the OE breaker or sensor plate. Rotate the HI-4 about 90 degrees to give better access to the cable exit hole. Install the HI-4 first, then push the cable through the hole. On some early models it may be necessary to enlarge the wire harness exit hole in the gear cover. Align the V notch on the HI-4 same as the OE plate you removed. Use the OE standoffs to secure the HI-4. You must use lockwashers under the standoffs for proper clearance between the HI-4 and cover plate. Do not fully tighten the standoffs until the timing has been set. 2. Route the HI-4 wire harness along the frame rails up to the coil. Make sure that harness will not be chafed or burned by exhaust heat. Secure harness with tie wraps. Do not install timing cover. HI-4 HOOKUP Crimp terminals and hardware are supplied for your convenience. Use the ring terminals for coil hookup. Use male-female quick disconnects for connections to the tach and vacuum switch (VOES). Tape up any unused wires. 1. Circuit Breaker Cover Screws (2) 2. Circuit Breaker Cover 3. Circuit Breaker Cover Gasket 4. Breaker Plate Screws (2) 5. Breaker Plate Screw Lockwashers & Washers (2 each) 6. Retainer (1971 to early 1972) 7. Circuit Breaker Cam Bolt 8. Breaker Plate Assembly 9. Breaker Cam 10. Advance Assembly 11. Gear Case Cover 11 10 9 8 7 6 5 4 3 2 1 NOTE: Damage will result if the brown tach wire comes in contact with +12V. Figure 1. Harley-Davidson®OE Points System
9000-4002A REV A 3 2/05 1. Identify switched +12 volt wire and tach wire (if equipped) going to the coil. Refer to your service manual, or reconnect the battery and use a test light or voltmeter. The switched +12 volt wire will be hot when the ignition key is turned on. 2. Refer to Figure 5. Connect the HI-4 red wire and switched +12 volt wire to Coil positive. 3. The HI-4 white wire is not used and should be taped. 4. Connect the HI-4 black wire to the Coil negative terminal. 5. Connect the HI-4 green wire to the vacuum switch (Figure 3, item 18), if used. 6. Connect the HI-4 brown wire to the tach wire, if equipped with tach. Tape up if unused. 7. The HI-4 is grounded via the timing housing; a separate ground connection is not required. 8. Reconnect battery ground cable. Verify proper ground connections to the frame and engine. VOES HOOKUP The OE vacuum switch (VOES) is normally an open circuit. Above 3-5 inch-Hg vacuum, the VOES closes and grounds the vacuum input on the OE ignition module. This increases the total advance generated by the OE ignition module. Vacuum advance improves part throttle 17 16 1. Cover Screws (2) 2. Ignition Timer Cover 3. Ignition Module 4. Timer Plate Screws (2) 5. Washers (2) 6. Screws & Washers (2 each) 7. Shield 8. Sensor 9. Trigger Rotor Bolt 10. Timer Plate 11. Trigger Rotor 12. Advance Assembly 13. Gear Case Cover 14. Ignition Coil 15. Spark Plug Wires (2) 16. Ignition Coil Terminal (FX) 17. Ignition Coil Terminal (FL) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 NOTE: Most motorcycle coils do not have terminals marked. Use either terminal for Coil+ (positive) and the other one for Coil- (negative). Warning: The HI-4 (8-1100) Dual Fire ignition will not work with 2 plugs per head, dual coil application. Damage will result if attempted. Use the HI-4 (8-2100) single fire ignition for 2 plugs per head applications

Incoming search terms:

HARLEY DAVIDSON SPORSTER, DYNA AND SOFTAIL LICENSE / TURN SIGNAL RELOCATOR INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Remove the license plate. Remove the license plate mounting bracket from the fender. Remove the two screws from the tail light lens and pull the light outward, unplug the wire connector and set aside. Unplug the turn signal wire connectors from the tail light base and push them out thru the hole in the fender. Looking up underneath the rear fender remove the wires from the clips that secure them to the bottom side of the fender. Cut the wires 2″ from the plugs as shown in photo 1. 2. Unscrew the signal housings from their mounting stems while rotating the wires on the inside of the fender so as not to twist them off while unscrewing the signal from the stem. Remove the signals pushing the wires thru from the inside while pulling the signal outward. Remove the nuts from the backside of the fender that secure the stems and remove the stems. 3. Assemble the license/turn signal bracket, turn signals. Place the smaller reinforcing bracket inside the license plate bracket. Locate the two supplied 5/16″ X 1″ bolts with holes drilled thru the center and the two supplied 5/16″ long spacers. Place the bolts thru the brackets from the inside, threads facing outward followed by the spacers. Thread the wires of the signals thru the bolts and thread the bolts into the signals and snug the bolts. 4. Mounting the LED lights a. Locate the supplied LED tail/brake lights. NOTE: this license plate holder is designed for the new U.S. standardized 7″ wide license plate. If you have an old style wider plate call us at the phone number below and we will send you a separate set of chrome brackets to work with your larger plate at no charge. b. Install the lights as shown in photos 2 & 3. Thread the wires of the LED lights thru the lower holes in the license bracket, peel the adhesive backing and press them firmly in place. Cut the wires off at about 18″ long. c. Install the license plate bracket with signals and LED lights onto the rear fender as shown in photos 2 & 3. Place the two supplied 1/4″ X 1″ flat head screws thru the license plate mounting block. Notice that the thicker half of the mounting block goes toward the top of the fender. d. Next route all the wires from the right turn signal and LED into the slot or notch on the backside of the mounting block followed by the rubber mounting gasket. Install the two nuts from the underside of the fender (Removed from the original license bracket.) onto the two flat head screws and snug them being sure the wires are all in the slot of the mounting block. Run all of the signal and LED wires thru the hole in the fender to the left of the mounting block. e. Install the license plate assembly onto the mounting block using the two supplied 1/4″ X 1/2″ flat head screws. Check the slack from all the wires and again be sure the wires are not pinched between the mounting block and the fender. Tighten all four flat head screws securely. Align the turn signals and tighten their mounting bolts securely.

YAMAHA ROADLINER AND STRATOLINER LAY DOWN LICENSEPLATE/ TAIL LIGHT INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-01-2011

download
1. Remove the license plate. Remove the license plate holder assembly from the rear fender (three 8mm Allen bolts 5mm wrench). Remove the five 4mm Allen screws underneath the rear fender which secure the taillight/turn signal assembly to the rear fender (3mm wrench). As shown in photo #2, pull the taillight assembly out away from the fender, turn it over, place a towel or rag between the light and fender and allow it to rest on the fender. 2. Locate the supplied triangular license plate mounting block, two 8 x 20mm Allen screws with holes driiled thru and three rubber washers. Place the two Allen screws thru the upper holes in the block and the rubber washers over the screws on the backside of the block. Start the screws into the upper holes on the fender. Use one of the three screws removed earlier from the original mount in the remaining lower hole of the new block sliding the remaining rubber washer between the block and fender. Tighten all three Allen screws secure enough to compress the rubber washers (4-6 ft lbs.). 3. Locate the supplied license plate mounting plate and LED lights. Cut off the excess red and black wires at the end of the black loom or tube. Referring to photo (1) thread the wires of the LED lights thru the small holes in the mounting plate, peel the cover from the adhesive backing on the lights and press them firmly into place as shown. 4. Locate the three supplied ¼” x ½” flat head Allen screws. Hold the plate up to the mounting block installed earlier with the wires at the bottom of the plate. Thread the wires from the LED lights thru the holes in the upper bolts of the block. Install the plate onto the block using the three flat head screws being sure to keep the exposed wire behind he plate as short as possible and fitting into the slot or cut out at the edge of the block. Snug the screws and again check to see tat the wires are in the slot or cut out in the block and do not become pinched as the screws are tightened. Tighten the screws securely. 5. Where the wires from the taillight go thru the fender there is a grommet, pull this grommet out from the fender. Thread the wires from the LED lights thru the grommet with the other wires. Replace the grommet into the fender and remove any slack from the wires under the fender. Cut the LED wires off at 6″ past the grommet. 6. Referring to photo (2) remove 2″ of the black tubing exposing the red and black wires on the LEDs. Locate the supplied brake/tail light dual function element (a red wire at one end with a red and orange wire at the other) and wire connectors. Cut all three wires on the dual element to 3″ long. Strip the end of the single red wire on the element and both of the red wires from the LEDs then connect them using one of the blue butt connectors. Connect the two black wires from the LEDs to any one of the black wires on the tail light or signals using one of the supplied splice connectors (place both black wires into one of the holes on the connector). Using the remaining splice connectors attach the red wire from the dual element to the yellow wire on the tail light and the orange wire to the blue wire on the tail light. Turn on the ignition and check that the LEDs are working both as tail and brake lights when the brakes are applied.

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE BILLET CAM SUPPORT PLATE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
REMOVAL NOTE For removal, refer to the appropriate sections of the applicable Service Manual for detailed information on the following generalized steps. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Remove the Maxi® fuse. 2. Remove the cam cover and gasket. 3. Remove and discard the crank and primary cam sprocket flange bolts and washers. 4. Release the oil pump, and remove the cam support plate and cams. Disassemble the cams from the support plate and discard the support plate. 5. Inspect cams, chain, sprockets, oil pump, chain tensioners and guide for wear and replace as needed. Refer to the Service Manual for inspection and replacement proce- dures. -J04503 INSTALLATION NOTES For installation, refer to the appropriate sections of the applicable Service Manual for detailed information on the following generalized steps. See Figure 1. When installing Screamin’ Eagle camshaft kits, install the O-ring included in this kit over the splined shaft of the rear camshaft as shown. 1. Using the Camshaft Assembly Tool (HD-47956) and assemble the camshafts, chains and tensioners to the billet cam support plate. 2. Install the cam support plate assembly into the crankcase. 3. Using the Crankshaft/Camshaft Locking Tool (HD-47941), install cam sprockets, chain and tensioner. 4. Install cam cover and gasket. 5. Install Maxi fuse.

Incoming search terms:

HARLEY-DAVIDSON 1979-Later Big Twin CONVERSION INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2012

download
Turn ignition switch to the OFF position. Disconnect the ground cable from the battery. 2) Disconnect the wire at the coil which runs down to the points. Remove the point cover plate. 3) Note the position of the slots in the point plate. When the Mallory UNILITEfi plate is installed, use the position of the slots to approximate the timing. 4) Remove the wire to the points. Remove the O.E. standoffs and washers. Remove the point plate assembly. 5) Remove the O.E. cam sleeve from the advance assembly. Place a small amount of oil on the advance shaft which supported the cam sleeve. 6) Slide the Mallory shutter wheel onto the advance shaft. Make sure the shutter wheel is all the way down into the advance assembly (it will only go one way due to the roll pin in the advance assembly). 7) Install the advance and shutter wheel into the nose cone. Make sure that the pin on the bottom of the advance engages the slot on the end of the camshaft. Apply Loctite to the threads and install the advance bolt. Torque to 25 in.lb. 8) Rotate the shutter wheel by hand (counter-clockwise) and release. It should rotate about 10 degrees and “snap” back when released. 9) Install the two Mallory standoffs. Place Loctite on the threads and torque to 16 in.lb. Do not use any washers with the standoffs. 10) Start the three wires of the Mallory UNILITEfi Module through the hole in the nose cone housing. (The module goes in towards the advance assembly with the flat plate outward). Pull on the three wires to remove any slack and prevent the wires from rubbing on the shutter wheel. 11) Rotate the UNILITEfi plate assembly until the slots in the plate are in the same position as the point plate was. This should make the timing close enough to start the engine. Slide the two Mallory 8-32 sleeve nuts (supplied) through the UNILITEfi plate and onto the male threads of the Mallory standoffs. Tighten the sleeve nuts just enough to prevent the plate from moving. 14) Route the wires from the UNILITEfi Module to the ignition coil, carefully avoiding the exhaust system. Connect the red wire to the positive (+) terminal (12 volts) on the coil. Connect the green wire to the negative (ñ) terminal on the coil (where the point wire was connected). Connect the brown wire to ground. The best place for the brown wire is the negative (ñ) post on the battery, however, any part of the frame or engine which is grounded to the battery will work

DUCATI EVOLUZIONE SLIPPER CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
If installing with Ducati OEM basket you need the washer cod. 0D1SR140C220045 (3mm). – If installing with STM basket (Z12 o Z48) you need the washer cod. 001MG019 (1,5mm). – Insert the correct washer on the gear shaft. – Perform the initial hub group assembly: position the progressive engagement steel plate (003MG015) on the hub (0F3SR140J24001C) , with the step facing up. Be careful to position it correctly into the specific seats, then check that pushing one side, the opposite stand up simultaneously. – Now put the 6 steel balls (001MG025) at the bottom of the grooves using a little bit of grease. Then fix the clutch drum (0F3SR140J24002C) on the clutch hub (0F3SR140J24001C) at rest position, using an M6 screw to help locking the two parts, avoiding in this way any possibility for the steel balls (001MG025) to fall out while inserting the hub pack on the main shaft. – Insert the hub pack on the gear shaft – Insert the clutch discs starting with the sintered one and finishing with the steel guided one; total disc set thickness must be included between 36 and 36,5mm. – Remove the M6 screw from the hub (0F3SR140J24001C). – Put the drum stopper hub (003MG106) on the hub (0F3SR140J24001C). – Verify that the secondary spring support (0F3SR540B140016) is well inserted into its housing on the drum (0F3SR140J24002C). – Insert the secondary spring (0S2085) into its housing on the drum (0F3SR140J24002C). – Mount the pressure plate (003MGP10) on the drum (0F3SR140J24002C) . – Position the Evoluzione spring (0S1090) on the pressure plate (003MGP10), with the convex part facing up (STM logo facing up), making sure previously that the squared section ring (901SE003), which works as primary spring support, is well positioned into the pressure plate itself. – Assemble the complete spring stopper pack: starting from the spring stopper plate (003MG008), with the shaped side facing up as shown in the picture. Insert the ball bearing (003MG007) and finally the spring stopper hub (0F3SR140N220007). Once completed these operations, position the complete spring stopper pack inside the Evoluzione spring (0S1090). – Insert the toothed washer (901RD101) with the convex side facing up, then insert and tighten up the clutch nut (0F30S140C220013); use a dynamometric wrench setting the torque suggested by the bike manufacturer. We suggest to use the specific optional tool (UTL-0020) in order to lock the pressure plate (003MGP10) while performing this operation. – Assemble the complete bearing rest pack: insert the washer (001MG018) in its housing on the bearing rest (0F3SR140N220004). Then put in the same housing the ball bearing and the push rod pin of the original clutch. – Position the complete bearing rest pack in the pressure plate (003MGP10), making sure it fits correctly into the housing grooves. – Manually practise a little pressure on the bearing rest (0F3SR140N220004) in order to release the seat for the tightness circlip (003MG018). – Fit correctly the above mentioned tightness circlip (003MG018). MAKE SURE that it adheres to all the groove perimeter. NB: Once completed the installation, repeatedly operate the clutch lever, checking that the pressure plate performs correctly the opening and closing movements. For a road use of the clutch you have to check clutch plates set every 2000 km. Please verify that the clutch plates set thickness is between 36,5mm and 35,0mm. If it is inferior to 35,0mm please replace a 1,5 steel plate with a 2 mm steel plate. For a racing use of the clutch we suggest to check the clutch plates set thickness frequently. GENERAL SAFETY REGULATIONS – In this sheet are reported the directions to perform correctly the clutch assembly operations. – STM reserves the right – without notice – to introduce any technical change whenever deemed it to be necessary to improve functionality and quality of the products. – Assembly operations must be performed by a skilled technician and must be scrupulously observed. – Before mounting the clutch make a complete inspection of the various parts, in order to verify the possible presence of faults or anomalies on the motorbike. – Make sure that there are no missing/damaged parts in the package . – Some parts of the clutch and its components can have sharp surface: handle with care. – Some components of the clutch, because of their small dimensions can be swallowed: keep away from children. STRADA srl Via Campo Archero 20 10023 Chieri ( TO ) Tel +39 011 9422832 Fax +39 011 9471447 003 MG 018 Tightness circlip

YAMAHA ROADLINER AND STRATOLINER LAY DOWN LICENSEPLATE/ TAIL INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 29-01-2011

download
1. Remove the license plate. Remove the license plate holder assembly from the rear fender (three 8mm Allen bolts 5mm wrench). Remove the five 4mm Allen screws underneath the rear fender which secure the taillight/turn signal assembly to the rear fender (3mm wrench). As shown in photo #2, pull the taillight assembly out away from the fender, turn it over, place a towel or rag between the light and fender and allow it to rest on the fender. 2. Locate the supplied triangular license plate mounting block, two 8 x 20mm Allen screws with holes driiled thru and three rubber washers. Place the two Allen screws thru the upper holes in the block and the rubber washers over the screws on the backside of the block. Start the screws into the upper holes on the fender. Use one of the three screws removed earlier from the original mount in the remaining lower hole of the new block sliding the remaining rubber washer between the block and fender. Tighten all three Allen screws secure enough to compress the rubber washers (4-6 ft lbs.). 3. Locate the supplied license plate mounting plate and LED lights. Cut off the excess red and black wires at the end of the black loom or tube. Referring to photo (1) thread the wires of the LED lights thru the small holes in the mounting plate, peel the cover from the adhesive backing on the lights and press them firmly into place as shown. 4. Locate the three supplied ¼” x ½” flat head Allen screws. Hold the plate up to the mounting block installed earlier with the wires at the bottom of the plate. Thread the wires from the LED lights thru the holes in the upper bolts of the block. Install the plate onto the block using the three flat head screws being sure to keep the exposed wire behind he plate as short as possible and fitting into the slot or cut out at the edge of the block. Snug the screws and again check to see tat the wires are in the slot or cut out in the block and do not become pinched as the screws are tightened. Tighten the screws securely. 5. Where the wires from the taillight go thru the fender there is a grommet, pull this grommet out from the fender. Thread the wires from the LED lights thru the grommet with the other wires. Replace the grommet into the fender and remove any slack from the wires under the fender. Cut the LED wires off at 6″ past the grommet.

Incoming search terms: