flstf floor replacment

You search Auto repair manual PDF flstf floor replacment, if there are search results will appear below. If search results do not exist, please search by others keyword.



  flstf floor replacment Direct Download speed 5282 Kb/s

  flstf floor replacment Full Version speed 6162 Kb/s



HARLEY DAVIDSON FLSTF FENDER TRIM INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION 1. Thoroughly clean the fender tip in the area where the trim will be mounted. 2. Cover the fender with masking tape to protect the painted surface during positioning of the trim. 3. Place the trim in the desired location and hold it in position. Mark the hole locations with a felt tip pen or pencil. Remove the trim. 4. Carefully center punch the hole locations in the fender. 5. Drill the mounting holes using a 1/8 in. (3 mm) diameter drill bit. 6. Remove the masking tape from the fender. 7. Mount the trim on the fender using the screws and lock nuts provided in the kit

HARLEY DAVIDSON LIGHTED MIRRORS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
REMOVAL Prepare for Service Touring Models: Remove left side saddlebag, left side cover, and maxi-fuse. Refer to SADDLEBAG and MAXI-FUSE in Service Manual. Softail and Dyna Models: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove seat according to the instructions in the Service Manual. 2. Disconnect battery cables, negative (-) cable first. 3. Remove fuel tank according to the instructions in the Service Manual. Sportster Models: Remove left side cover and maxi-fuse. Refer to MAXI-FUSE in Service Manual. V-Rod Models: Remove right side cover and maxi-fuse. Refer to MAXI-FUSE in Service Manual. Remove Existing Mirrors Touring and Softail (Except FXSTD, FLSTF) Models Left side: See Figure 1. Remove acorn nut (1), star washer (2), and existing mirror (3) from clutch hand control assembly. Discard star washer and mirror but save acorn nut. Right side: See Figure 2. Remove acorn nut (1), star washer (2), and existing mirror (3) from front brake hand control assembly. Discard star washer and mirror but save acorn nut. 2 1 3 is03431 1. Acorn nut 2. Star washer 3. Mirror, left Figure 1. Remove L.H. Mirror (Except Sportster) 2 1 3 is03432 1. Acorn nut 2. Star washer 3. Mirror, right Figure 2. Remove R.H. Mirror (Touring, Softail – Except FXSTD, FLSTF) Dyna, FXSTD, FLSTF, and VRSC Models 1. Left side: See Figure 1. Remove acorn nut (1), star washer (2), and existing mirror (3) from clutch hand control assembly. Discard star washer and mirror but save acorn nut. 2. Right side: See Figure 3. Loosen ball stud clamp (1) to remove directional lamp assembly (2). Remove retainer (3), star washer (4), and existing mirror (5) from front brake hand control assembly. Discard star washer and mirror but save remaining parts. 2 5 3 1 4 is03428 1. Ball stud clamp 2. Directional lamp assembly 3. Retainer 4. Star washer 5. Mirror, right Figure 3. Remove R.H. Mirror (Dyna, FXSTD, FLSTF, VRSC) Sportster Models Left side: See Figure 4. Remove locknut (1), washer (2), and existing mirror (3) from clutch hand control assembly. Discard washer and mirror but save locknut. Right side: See Figure 4. Remove locknut (1), washer (2), and existing mirror (4) from front brake hand control assembly. Discard washer and mirror but save locknut. 3 2 1 2 1 4 is03414 1. Locknut (2) 2. Washer (2) 3. Mirror, left 4. Mirror, right Figure 4. Remove Mirrors (Sportster) INSTALLATION Install Lighted Mirrors Touring and Softail (Except FXSTD, FLSTF, FXSTS, FLSTS) Models 1. Left side: See Figure 5. Install mirror stem (1) through clutch hand control assembly.

Incoming search terms:

HARLEY DAVIDSON FLSTC, FLSTF, FLSTS BLACK ENGINE GUARD INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
The front and/or rear guard(s) can provide limited leg and cosmetic vehicle protection under unique circumstances. (Fall over while stopped, very slow speed slide.) It is not made or intended to provide protection from bodily injury in a collision with another vehicle or any other object. (00022a) Kit Contents See Figure 4 and Table 1. INSTALLATION 1. See Figure 1. Note mounting locations for engine guard. 2. See Figure 2. Hold Engine Guard (1) in place. Attach top center mounting flange of engine guard to cross brace located between front downtubes just below the steering head with panhead screw (4), 5/16 inch washer (3) and 5/16 inch hex nut (2) as shown. Tighten finger tight. is04094 Figure 1. Installed Engine Guard 3. See Figure 3. On left side of the bike, attach the engine mounting guard (1) in the indicated location with a button- head screw (4), 3/8 inch washer (3) and 3/8-16 nylon locknut (2). Tighten finger tight. 4. Repeat installation on right side of the bike, attach the mounting guard in the indicated location. Tighten to 33 ft- lbs (44 N-m). 5. Tighten engine guard left side mounting hardware to 33 ft-lbs (44 N-m). Tighten engine guard top mounting hardware to 19 ft-lbs (25 N-m).

HARLEY DAVIDSON FLSTF TURN SIGNAL RELOCATION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL 1. Remove seat according to the instructions in the Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. See Figure 1. Disconnect battery cables, negative (-) cable first. 2 1 is03242 1. Negative (-) cable 2. Tail lamp connector Figure 1. Negative Battery Cable and Tail Lamp Connector 3. See Figure 2. Remove two screws and tail lamp lens (1) from base (2). 2 1 is03243 1. Tail lamp lens 2. Tail lamp base Figure 2. Remove Tail Lamp Lens 4. See Figure 3. Using a Terminal Pick Tool (1), depress locking tabs and disconnect turn signal connectors (2- place) (2, 3) from circuit board. 5. Feed turn signal wiring and connector through opening in circuit board assembly and into rear wheel area. 6. See Figure 4. Remove turn signal wiring (1, 2) from clips (3) under rear of fender INSTALLATION NOTE Proper installation of kit requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. Route Turn Signal Wiring Through Rear Fender and Support 1. See Figure 5. Remove three rear screws (1) from fender support (2). 2. Loosen, but do not remove two front screws (3) from fender support. 1 3 2 is03285 1. Screw, rear (3) 2. Fender support 3. Screw, front (2) Figure 5. Fender Support Screws and Fender Support 3. Pull fender support away from rear fender to gain access to turn signal mount. 4. Remove stock screw and washer from turn signal mount. 5. See Figure 7. Pull turn signal (B) and turn signal mount (A) away from fender support. 6. Remove turn signal and wires from vehicle by routing turn signal wiring and connector through holes in rear fender and fender support. Gently guide wires through holes to ensure they do not get damaged. Feed Wiring and Install Relocation Bracket 1. See Figure 6. Feed turn signal wiring and connector through middle hole in turn signal relocation bracket and under rear of fender support. 1 is04635 1. Wire harness Figure 6. Wire Harness Routing 2. See Figure 7. Insert stock screw and washer through rear hole of relocation bracket (1) and turn signal mount (A). 3. Thread screw into turn signal (B). Tighten to 12-16 ft-lbs (16.3-21.7 Nm). 4. Align relocation bracket (1) with rear of fender support and install with screw (2) and nut (3) from kit. Tighten nut to 12-16 ft-lbs (16.3-21.7 Nm). Complete Turn Signal Relocation Wiring 1. See Figure 5. Install one rear screw (1) to hold fender support in place while routing wiring. Install screw snugly but do not fully tighten

Incoming search terms:

HONDA GL18005 Passenger Floor Board Risers Installation Instructions

0

Filed Under (Honda) by admin on 23-12-2010

download
Flip the passenger floorboards in the up or closed position. Remove the four (4) allen bolts that attach them to the frame. Install the carriage bolts (round heads) into the backside of the risers (side opposite of recess for mounting screws). Then the plastic washer, next the floorboard, then a washer, lock washer and nut but do not tighten yet. Install the riser floorboard assembly back onto the frame using the original allen bolts and placing the aluminum spacers between the risers and the frame, tighten securely. Note: the curved slots should sweep up and back towards the rear of the motorcycle. You may reverse the left and rights so that the slots curve forward to gain further forward placement of the passenger’s feet if desired. Set floorboards to desired height and tighten securely

1994 HARLEY DAVIDSON FXD (DYNA) PASSENGER FLOOR BOARDS AND RELOCATION ARMS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-04-2012

download
1. Beginning on the RIGHT side, use a 9/16″ wrench to remove the bolt from the back of the passenger peg mount. Remove entire peg assembly. 2. Remove the new floorboards and mounts from their packaging. Notice the Left and Right markings on the backside of the floorboard mounting plates. 3. Install the supplied Right floorboard support (the longer one) with the round mounting face for the floorboard towards the upper-right using the supplied 7/16 x 1 º” long bolt. Apply blue Loctite to the threads. Insert the bolt from the backside where the original peg was mounted. Use a 5/8″ wrench & tighten securely. Note: If also installing with optional Relocation Arms (#FXD005-5) skip step 4 and go onto step 5. 4. Installation of Right Floorboard only. There are two sets of alignment holes on the floorboard support. Insert two of the four dowel-pins into the dowel pinholes at six and twelve o’clock. Place the right floorboard onto the mount and dowel pins so that it is parallel (horizontal) to the ground. Insert the supplied 5/16 X 1″ socket head cap screw through the floorboard mount & thread into the floorboard support. Use a º” hex key wrench & tighten securely. 5. Remove Right Floorboard – Installation of Right Floorboard with Relocation Arm. There are two sets of alignment holes on the floorboard support. Insert two of the four dowel pins into the dowel holes 180 degrees apart. Notice the L & R markings on the backside of the relocation arms. Install the Right relocation arm so marking (R) is facing inward and the threaded hole is facing toward the front of the motorcycle. There are two sets of alignment holes on the relocation arms. Place the arm onto the mount (Match dowel pin holes) in desired upper or lower position. Insert the supplied 5/16 X 1″ socket head cap screw through the relocation arm & thread into the floorboard support. Use a º” hex key wrench & tighten securely. 6. At the other end of the relocation arm there are two sets of alignment holes. Insert two of the supplied dowel pins into the set of dowel pin holes 180 degrees apart that will allow the floorboard to be horizontal or parallel to the ground. Insert the supplied 5/16 X 3/4″ socket head cap screw through the floorboard mount & thread into the link arm. Use a º” hex key wrench & tighten securely.

Incoming search terms:

TRIUMPH ROCKET III DRIVER FLOOR BOARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 24-12-2010

download
1. Starting on the left (shifter) side remove shifter pivot bolt (large allen head). Rotate the shifter assembly out of the way. Remove the retaining clip from the bottom of the foot peg pivot pin. Remove the pin and the foot peg. 2. Install the left floorboard in the original foot peg mounting location. (Note the L & R markings on the backside of the mounting blocks.) Place the allen bolt (supplied) through the original mount and the floorboard. It may also help to use the shank of a Phillips screwdriver in the bolthole at the same time to help align the holes. In some cases due to variances in the stock foot peg bracket it you may need to use a 25/64″ (.390) drill bit and drill thru both the bracket and the floorboards mounting block to allow the bolt to go thru. The blocks and their holes are machined to exact tolerances and is kept as close as possible to the size of the peg bracket so that there will not be any looseness or drooping of the floorboards when installed. Thread one of the Ny-loc nuts (supplied) onto the bolt and tighten securely. Reinstall shifter assembly and tighten securely. 3. Repeat for right side and re-check hardware for tightness. (The brake assembly will not need to be removed.)

HARLEY DAVIDSON FXD (DYNA) PASSENGER FLOOR BOARDS AND RELOCATION ARMS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 21-12-2010

download
1. Beginning on the RIGHT side, use a 9/16″ wrench to remove the bolt from the back of the passenger peg mount. Remove entire peg assembly. 2. Remove the new floorboards and mounts from their packaging. Notice the Left and Right markings on the backside of the floorboard mounting plates. 3. Install the supplied Right floorboard support (the longer one) with the round mounting face for the floorboard towards the upper-right using the supplied 7/16 x 1 º” long bolt. Apply blue Loctite to the threads. Insert the bolt from the backside where the original peg was mounted. Use a 5/8″ wrench & tighten securely. Note: If also installing with optional Relocation Arms (#FXD005-5) skip step 4 and go onto step 5. 4. Installation of Right Floorboard only. There are two sets of alignment holes on the floorboard support. Insert two of the four dowel-pins into the dowel pinholes at six and twelve o’clock. Place the right floorboard onto the mount and dowel pins so that it is parallel (horizontal) to the ground. Insert the supplied 5/16 X 1″ socket head cap screw through the floorboard mount & thread into the floorboard support. Use a º” hex key wrench & tighten securely. 5. Remove Right Floorboard – Installation of Right Floorboard with Relocation Arm. There are two sets of alignment holes on the floorboard support. Insert two of the four dowel pins into the dowel holes 180 degrees apart. Notice the L & R markings on the backside of the relocation arms. Install the Right relocation arm so marking (R) is facing inward and the threaded hole is facing toward the front of the motorcycle. There are two sets of alignment holes on the relocation arms. Place the arm onto the mount (Match dowel pin holes) in desired upper or lower position. Insert the supplied 5/16 X 1″ socket head cap screw through the relocation arm & thread into the floorboard support. Use a º” hex key wrench & tighten securely

Honda VTX1800C/ J Left/ Ringht Floor Board Assembly Instruction Manual

0

Filed Under (Honda) by admin on 14-11-2010

download
Left Side 1. Unplug the horn wires. 2. Unbolt the left side foot peg bracket assembly and save the hardware, the stock bolts will be used to install your new Cobra floorboards. 3. Remove horn and the shift lever from the stock mount and install onto the new Cobra mount the same way they were on the stock mounts. Install the 8mm acorn nut on the exposed threads from the shift lever bolt. 4. Bolt the Cobra floorboards to the motorcycle using the stock bolts and torque to factory specifications. Note: Make sure shift lever operates properly and that there is adequate clearance. Right Side 1. Remove chrome cover from the top of the rear brake master cylinder by removing the two nuts on top. 2. Remove brake lever return spring and the stop light switch spring. 3. Remove rubber plug from the center of the brake lever pivot bolt then remove the bolt. 4. Remove the two bolts that hold the master cylinder and brake light switch/chrome cover mount. 5. Unbolt the right side foot peg bracket by removing the two stock 10mm bolts and save the hardware, the stock bolts will be used to install your new Cobra floorboards. Note: look at the placement of the large spacers behind the foot peg bracket they will need to be re-installed in the same position. Also note the nut on the inside of frame rail for lower bolt. 6. Install the Cobra floorboard using the stock bolts and spacers removed in previous step. 7. Remount the master cylinder and brake light switch/chrome cover mount removed in step 4 the same way it was on the stock mount bracket, reuse stock hardware. 8. Install the brake lever using the stock pivot bolt & rubber plug that was removed in step 3

Honda VTX1800F Left/ Right Floor Board Assembly Installation Manual

0

Filed Under (Honda) by admin on 14-11-2010

download
1. Unplug the horn wires. 2. Unbolt the left side foot peg bracket assembly and save the hardware, the stock bolts will be used to install your new Cobra floorboards. 3. Remove horn and the shift lever from the stock mount and install onto the new Cobra mount the same way they were on the stock mounts. Install the 8mm acorn nut on the exposed threads from the shift lever bolt. 4. Bolt the Cobra floorboards to the motorcycle using the stock bolts and torque to factory specifications. Note: Make sure shift lever operates properly and that there is adequate clearance. Right Side 1. Remove chrome cover from the top of the rear brake master cylinder by removing the two nuts on top. 2. Remove brake lever return spring and the stop light switch spring. 3. Remove rubber plug from the center of the brake lever pivot bolt then remove the bolt. 4. Remove the two bolts that hold the master cylinder and brake light switch/chrome cover mount. 5. Unbolt the right side foot peg bracket by removing the two stock 10mm bolts and save the hardware, the stock bolts will be used to install your new Cobra floorboards. Note: look at the placement of the large spacers behind the foot peg bracket they will need to be re-installed in the same position. Also note the nut on the inside of frame rail for lower bolt. 6. Install the Cobra floorboard using the stock bolts and spacers removed in previous step. 7. Remount the master cylinder and brake light switch/chrome cover mount removed in step 4 the same way it was on the stock mount bracket, reuse stock hardware. 8. Install the brake lever using the stock pivot bolt & rubber plug that was removed in step 3