fluid capacity for 2004 heritage softtail

You search Auto repair manual PDF fluid capacity for 2004 heritage softtail, if there are search results will appear below. If search results do not exist, please search by others keyword.



  fluid capacity for 2004 heritage softtail Direct Download speed 5282 Kb/s

  fluid capacity for 2004 heritage softtail Full Version speed 6162 Kb/s



Skyteam ST 125 SPECIFICATIONS AND SERVICE MANUAL

0

Filed Under (Skyteam) by admin on 24-11-2010

download
BRAKES This motorcycle has a hydraulic brake system of front and rear . Brakes are items of personal safety and should be properly adjusted. Remember to check periodically the brake system and these checks should be conducted by qualified Jincheng dealer. Do not use the remained brake fluid from on a unsealed container, never reuse the brake fluid remained in the last repairing, because the used brake fluid may absorb the water from the air. Use DOT 4 brake fluid from a sealed container. Do not spill out the brake fluid, when the brake fluid is glued to the paint, plastic and rubber material, a chemical reaction shall take place, causing the damage. (1)lower level mark Front brake Rear brake BRAKE FLUID (1) (2) (3) (1) (1)Brake fluid cap (2)Max. fluid level mark (3)Min. fluid level mark Brake fluid may cause irritation. Avoid contact with skin or eyes. In case of contact, flush thoroughly with water and call a doctor if your eyes were exposed NOTICE WARINING * 9 BRAKE LINING The main points for checking the front brake lining are to see whether the lining wear is out of the range. Replace the brake lining wear is out of the range. Replace the brake lining if the lining wear is beyond the brake wear limit mark. FRONT BRAKE FLUID LEVEL Check that the fluid level is above the lower level mark(1) with the motorcycle in an upright position. Brake fluid must be added to the reservoir when ever the fluid level begins to reach the lower level mark(1). Fill the reservoir up to upper level mark. REAR BRAKE FLUID LEVEL There are two marks in rear brake fluid cap,keep the fluid lever between the Max. fluid level mark (2) and the Min. fluid level mark (3) always. Check if it is short of brake fluid, check the hose and other components for corrosion or cracks. limit mark Brake Pad Front brake Rear brake If the brake system or brake linings have to be repaired, we suggest that these repair should be performed by your authorized SKYTEAM dealer. SKYTEAM dealer knows your motorcycle best and is dedicated to your complete satisfaction

Incoming search terms:

2001 – 2004 Camry, Highlander, Solara & 2004

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
2004 model year Camry, Highlander, Solara and 2004 model year RAV4 vehicles with the 2AZ-FE engine may exhibit squealing and/or rattling noises coming from the engine compartment during vehicle operation especially after a cold soak. The belt tensioner assembly has been improved to correct this condition. 2001 – 2004 model year Camry, Highlander and Solara vehicles equipped with 2AZ-FE engines produced BEFORE the Production Change Effective VINs shown below. 2004 model year RAV4 vehicles produced BEFORE the Production Change Effective VINs shown below. MODEL ENGINE LINE PRODUCTION CHANGE EFFECTIVE VIN TMMK Line 1 4T1BE3#K#4U358206 Camry TMMK Line 2 4T1BE3#K#4U914052 y 2AZFE Tsutsumi JTDBE3#K#40296732 Highlander 2AZ-FE TMK JTE#D2#A#40100501 Solara TMMK 4T1CE3#P#4U914074 RAV4 Tahara JTE#D2#V#40029797 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME QTY 16620-28010 16620-28011 Tensioner Assembly, V-ribbed Belt 1 OP CODE DESCRIPTION TIME OFP T1 T2 EG8001 R & R Accessory Belt Tensioner 0.9 16620-28010 91 55 Applicable Warranty*: This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

Incoming search terms:

2003 – 2004 4Runner, 2004 Highlander, Prius, Sienna And Solara POWER WINDOW / ROOF INITIALIZATION PROCEDURES

0

Filed Under (Toyota Manuals) by admin on 17-10-2011

download
Turn the ignition switch ON. 2. Open the window halfway by pressing the power window switch. 3. Fully pull up the switch until the power window is fully closed and continue to hold the switch for at least three (3) seconds after the power window is fully closed. 4. Check that the “AUTO UP/DOWN” function operates normally. B. Back Door Power Window (4Runner) 1. Turn the ignition switch ON. 2. Open the back door glass. 3. Press the back door power window switch until the door glass is fully closed and continue to hold the switch one (1) second or more after the door glass is fully closed. 4. Check that the “AUTO UP/DOWN” function operates normally. C. Power Sliding Roof (4Runner, Sienna, Solara) 1. Turn the ignition switch ON. 2. Initialize the sliding roof by pressing and holding the TILT UP switch until the roof glass tilts upward fully (the roof glass automatically tilts downward slightly after fully tilting upward). 3. Release the switch. 4. Check that the “AUTO OPEN/CLOSE” function operates normally

2003 – 2004 4Runner & Tundra, 2004 Camry, Highlander, Sienna & SolaraREPAIR MANUAL SUPPLEMENT LEV II EVAP SYSTEM CHECK

0

Filed Under (Toyota Manuals) by admin on 24-10-2011

download
this TSB provides detailed instructions for a new LEV II EVAP System Check function using the Diagnostic Tester. The LEV II System Check allows the Diagnostic Tester to display the fuel tank vapor pressure as the EVAP VSV and the CCV are operated in a specific six-step pattern. Problems with the EVAP system are quickly isolated by observing the change in vapor pressure during each step. Once the vehicle condition is corrected, the LEV II System Check can also be used to confirm the repair before the vehicle is returned to the customer. The inspection procedure using the LEV II System Check (LEV II SYS CHECK) is described in this bulletin. This function is available using a Diagnostic Tester with version 11.0a software (or newer

New Automatic Transmission for Motorcycles Human-Friendly Transmission

0

Filed Under (Honda) by admin on 18-12-2011

download
High-pressure fluid flow The engine rotates the pump swash plate, which has a gear mechanism. The rotating swash plate pushes the pump pistons to increase the pressure on the hydraulic fluid and feed it to the high-pressure annular chamber. The high- pressure fluid is then fed to the oil motor piston chamber where it pushes the pistons forward, which then push the motor swash plate. Power Fluid flow from pump to motor Fluid flow from motor to pump Low-pressure fluid flow The lower-pressure hydraulic fluid returns to the pump through the low-pressure annular chamber. In this way, the fluid circulates between the pump and the motor. Movement of distributor valves and pistons The distributor valves play an important role in fluid circulation. The valves are placed both in the oil pump and motor. When the pump pistons move to the compression side, the valves connect the piston chamber and the high- pressure chamber. When the pump pistons move to the expansion side, the valves allow a connection between the piston chamber and the low-pressure chamber. The valve in the oil motor moves opposite to its counterpart in the pump, ensuring the circulation of fluid within the system

Incoming search terms:

Automatic Transmission/ Transaxle Fluid Level Inspection Temperature Rang es

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
For vehicles equipped witha transmission requiring the use of the overflow type automatic transmission fluid (ATF) inspection process, the A TF must be withinaspecific temperature range for accurate fluid level inspection. Inspecting the A TF outside of the specified temperature range may result in incorrectA TF fluid levels and could lead to shift quality, M.I.L. “ON”, and/or transmission damage issues. Please seethe information in this bulletin for updated A TF level inspection temperature ranges. HINT For additional information including animations and video illustrations, please seethe Technical Training course E076: “Toyota ATF Level Inspection”. NOTE Please see TSB No. TC 010-07, “World Standard Automatic Transmission Fluid”, for important tips when working with A TFWS. ©2008 ToyotaMotor Sales, USA Page 1of3
T-SB-0129-08 July9,2008 Page 2of3 Automatic Transmission/Transaxle Fluid Level Inspection Temperature Ranges Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty – - — Parts Information PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME QTY 00289-ATFWS Same ATFWS As needed Required Tools&Equipment

HARLEY DAVIDSON BRAIDED, DUAL DISC, FRONT BRAKE LINE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-04-2011

download
INSTALLATION 1 is03017 1. Bleed valve cover Figure 1. Brake Caliper Bleed Valve Rubber Cover 2 1 3 is03018 1. Plastic tube 2. Caliper bleeder valve 3. Container Figure 2. Draining Brake Fluid NOTE This instruction sheet covers motorcycle models that use either DOT 4 or DOT 5 Hydraulic Brake Fluid. The owner’s manual -J03109 1 of 2 will indicate which type of br ake fluid should be used on the motorcycle. Read and follow the owner’s manual carefully. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 1. See the service manual and disconnect negative (-) battery cable or remove the main fuse. Save the seat hardware for installation. 2. See Figure 2. Open bleeder nipple cap on front brake caliper. Install end of a length of plastic tubing over caliper bleeder valve (1), while placing free end in a suitable container. Open bleeder valve approximately 1/2 turn. Pump brake lever to drain brake fluid. Repeat step for the other caliper. 3. Remove bolt and two sealing washers to disconnect brake line fitting from master cylinder. Save bolt and discard washers.

2002-2007 HONDA VFR 800 WITH ABS GALFER BRAKE LINE KIT INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 03-03-2011

download
Prep the motorcycle for this job A. Park motorcycle on the center stand in a well-lit shop (Fig.A) B. Note: it is not absolutely necessary to remove the fuel tank and body panels. However, brake fluid is VERY CORROSIVE TO PAINT. We decided to be safe (Fig. B) and removed the lower fairing left and right rear sides, fuel tank, front fender, seat, and black A B plastic inner fairing front parts, battery cover, and rear master cylinder cover according to the owner’s manual. This also gives better access to the fittings. (Fig C) C. After safely storing the body panels and fuel tank, remove wind shield, (brake fluid, even a drop, will permanently mark any clear plastic), cover the dash and all gauges with a towel. II. Draining the brake fluid from the systems. A. A copy of the factory instructions has been included with this kit on how to properly and safely drain, fill and bleed the brake fluid from the brake systems. Follow the directions closely and remove the fluid according to the instructions. Dispose of the old fluid properly—DO NOT REUSE. B. If you purchased the clutch line, then perform the following steps (Fig D): In the bag marked Clutch Line: remove the left side lower body panels. Remove vehicle speed sensor, and remove the coolant C D tank. Remove the clutch fluid from the master cylinder on the left clip-on. Remove the fluid from the clutch line and slave cylinder. This factory line is NOT attached along the inner frame spar so here is a little trick that made this a 20- minute job including the bleed: 1. Remove the banjo bolts from the master cylinder and the clutch slave ends. 2. With a nice heavy wire tie, attach the slave end of the new braided line to the lever end of the factory line. Snip off the tail of the wire tie. Wrap this “joint” with electrical tape. 3. Pull from the factory slave end until you get the braided line end to the clutch slave. If it gets caught on something, try turning the end you are pulling from. 4. Remove the tape, carefully cut off the wire tie, install new sealing washers and bolts at both ends and torque to 17-21 foot/lbs. maximum. Bleed the clutch. III. Removing the factory front brake hoses and calipers – Front A. With the fluid drained and disposed of properly, loosen the bolts that hold the right caliper to the right fork leg (Fig E). Also remove the two 8mm bolts from the ABS front wheel speed sensor. Loosen all of the hose mounting blocks on the front forks on both sides; also loosen the blocks for the crossover pipe (Fig F) between the fork legs. Also loosen the frame pipe mounts and the mount for the front lever line that is also E attached to the right side of the frame. Loosen the left caliper mounting bolts (Fig G). B. Remove the calipers and remove the hose mounts under the lower triple tree. Remove the hard pipes from both the left and right hard pipe to soft line frame mounts on the frame (Fig. H). On the front ABS modulator remove the short soft line that is connected to the mount block. (Fig I.a. & I.b.) C. Carefully remove the

2004 Highlander, Land Cruiser and Prius MULTI-DISPLAY FUNCTIONS ARE INOPERATIVE

0

Filed Under (Toyota Manuals) by admin on 26-10-2011

download
Confirm the connectors to the multi-display are fully seated. Replace any damaged connectors. 3. If all the TX
terminals are tight and the connectors are fully seated, replace the multi-display. NOTE: For Highlander multi-display Removal and Replacement, refer to the Technical Information System (TIS), 2004 model year Highlander Repair Manual: Audio & Visual System: Multi-display (CRT display): Replacement. For Land Cruiser multi-display Removal and Replacement, refer to TIS, 2004 model year Land Cruiser Repair Manual: Body (Mechanical): Instrument Panel: Removal. For Prius multi-display Removal and Replacement, refer to TIS, 2004 model year Prius Repair Manual: Audio & Visual System: Multi-display Assy: Replacement.

Incoming search terms:

2004-2007 HONDA CBR 1000RR Super bike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Make sure to save the nut and bolt that are currently holding the stock lower section of the hoses. (See picture A) Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, 40-degree banjo from right line, washer, 40-degree banjo from left line, washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. (For positioning see picture B) . Make sure that the 90-degree fittings on each caliper are pointing straight up (see picture C) . Thread each banjo end onto the adapter, and torque to 6 ½ Ft pounds. Please tighten the “C” clips on the fender using the OEM bolts we asked you to save above. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, using the galfer 2line clip to bring the lines together and mounting it to the triple tree will insure proper clearness and routing. (See picture D) Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with Galfer DOT 4- brake fluid is recommended.

Incoming search terms: