foam handle grips installtion factory

You search Auto repair manual PDF foam handle grips installtion factory, if there are search results will appear below. If search results do not exist, please search by others keyword.



  foam handle grips installtion factory Direct Download speed 5282 Kb/s

  foam handle grips installtion factory Full Version speed 6162 Kb/s



2009 Kawasaki Voyager Heated Grips Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove the Factory Grips Before removing the factory grips, the”chromed plastic”grip end caps need to be removed. The chromed plastic ends are threaded on, but have”left hand”threads, which means to unscrew you need to turn them clockwise. (The opposite way that you would normally unscrew something) To do that I recommend using, either a rubber strap wrench, ora sheet of thin rubber used as you would to loosen the lid of ajar. Once Ihadtheend caps off, I used a sharp utility knife to cut through, and peel off the factory rubber grips. (They are only about 1/8″thicksoit’seasytodo.) With the rubber grips off, I removed the chromed ring that is adjacent to the left switch housing. The left ring will come off, witha gentle pull, but the throttle side ring will need to be cutoff, as it’s pressed on. It’seasytodo; I cut it off using wire side cutters (see picture on page 3 below). 2 Factory left and right Grips After removing the chromed end cap, and the factory rubber grips. The chromed plastic ring next to the switch housing needs to be cut off. Note all the ridges on the sleeve, all these except one ridge need to be filed off. 1. Prepare left handlebar for grip installation The left handlebar is pretty easy to prepare, first I cleaned any glue from the bar, and then gently test fit the left grip, be very careful here as it needs to slide on easily. Asper the instructions, ” Do not force the grip on with anything greater than gentle hand force “. Remember after the test fit you need to take it off again. (You could also crack the heated grip if it’stootight). If you find it too tight, as I did sand the bar using sandpaper until it slides on and off easily. On my bike I used an 80 grit sandpaper, and it took approx 20 minutes to geta good fit

FC Shock Spring Installation Guide

0

Filed Under (Tips and Review) by admin on 14-12-2010

download
Installation: 1. Remove the fork springs according to the OEM Owner’s Manual. 2. Check/adjust fork oil level and weight according to OEM Specifications. Caution: Most inverted forks will not require the use of any shim washers or spacers. In cases where use is necessary with the twin chamber style fork, the shims must be placed at the bottom of the spring. Most conventional forks (non-inverted) will use shim washers or spacers at the top of the fork spring. 3. Install Factory Connection fork springs and refer to OEM Owner’s Manual for proper assembly procedures. 4. Be sure to double check all fasteners. Note: Most modern day forks require special tools for disassembly and assembly of the components. Examples : Showa 47/49mm Twin Chamber, KYB 48mm Twin Chamber, WP 07 SX Models/SXS Components. Installing fork springs is an intricate process that should be performed with extreme care by a qualified suspension technician. Failure to install the springs correctly could cause damage to one or more components of the fork. This damage, although not readily apparent, could lead to unexpected failure or rider injury. Factory Connection manufactures models specific fork springs. Installation of a Factory Connection spring not designed for your motorcycle may result in unexpected failure and rider injury. Please consult your Factory Connection spring dealer or call Factory Connection directly if you are unsure about a spring/or springs. 1. Factory Connection’s Limited Lifetime Warranty Factory Connection warrants, to the original retail purchaser (“consumer”) who retains ownership of the vehicle on which the suspension spring(s) (“products(s)”) was originally installed, all suspension springs for life against factory defects in material and workmanship (other than defects in finish) when used under normal use and operating conditions. 2. Your Remedy Upon verification of warranty coverage, Factory Connection at its option will replace defective or prematurely worn-out product (s), without charge, or refund the purchase price of the products(s). This is the Consumer’s sole and exclusive remedy for any loss or damage, however arising, due to a nonconformity or defect in the product(s). 3. Warranty Claim Procedure To make claim under this warranty, the consumer should contact the Factory Connection dealer or Factory Connection where the product(s) was purchased. Factory Connection reserves the right to test the returned product(s) to evaluate the nonconformity or possible defect. The Consumer is responsible for all costs of returning the defective or prematurely worn-out product(s) to the Factory Connection dealer as well as all costs for removing the product(s) from and installing the products(s) on the vehicle.

Incoming search terms:

Harley- Davidson Bagger Audio factory service manual for removal

0

Filed Under (Harley Davidson) by admin on 03-04-2012

download
POWER & SPEAKER HARNESS INSTALLATION- (Read electrical connections prior to connecting center power and ground wires) 1. Disconnect battery (negative cable first!) 2. Remove outer faring cover 3. Route long speaker wires from fairing area through tank channel to seat area. 4. Route one pair of speaker wires under each fender strut support; purple and purple and black wires to the right and green and green and black wires to the left. AMPLIFIER INSTALLATION- 1. Factory installed electronics will determine suggested placement of amplifier. 2. Position and attach amplifier to outer fairing support bars with supplied wire ties. (Electra/Ultra/Street Glide) BAGGER AUDIO™ LIDS INSTALLATION- Detach factory lid by removing the 2 screws holding the factory strap to inner lid and 5 small torque screws holding lid to factory latch assembly. (Consult factory service manual for further instructions) Remove metal strap from behind factory seal (This is the metal strap that the previous 5 small torque screws were removed from) Position metal strap in same location on your new lid. (If you purchased your product unpainted, you must install the supplied seal to your finished lid) Reattach BAGGER AUDIO™ LIDS by installing the 5 small torque screws in the same location as on the factory lid. (We suggest that you have an assistant hold the lid in place while attaching your new lids) Replace factory nylon Hinge straps with new nylon straps supplied in kit. Use metal straps and machined screws to secure the nylon hinge straps. 
 Place a small bead of silicone on the inside rim of the speaker basket to create a watertight seal between the inside of the lid and the speaker. 
 Install speaker into the bottom of the lid (not through the top opening) with supplied stainless screws and washers (4 per lid). Be sure to center speaker in lid opening to ensure proper speaker grill placement. Install speaker with terminals facing toward the front of the lid. One 1/4″ hole must be drilled in each bag. Holes can be positioned at the ownerʼs discretion. Place rubber grommet in drilled hole before running wires

HARLEY-DAVIDSON Starter Relay Location Guide

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Touring 1998 – 2007 Additional Notes: Relay Location: Under Seat in rubber Boot Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 ***2004 – 2007 FLHR series bikes & 2007 FLHX require additional Adaptor AD-1 & DGD-1. Start Relay is in Power Distribution box. Replaces H-D Relay part# 31579-04 Softails 2000 – 2007 Additional Notes: 2000 is when the Softails changed to Twin Cams. Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Softails 1996 – 1999 Additional Notes: Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05
Dyna 2007 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Replace Batt 15A Fuse with Supplied Fuse Holder Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Tap 12v Fuse (Batt 15A) System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Dyna 2000 – 2005 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Battery connection is made direct to Battery Buss to right of Relay * see Pic3 Installation Notes: Remove Outer Cover, then Remove 4 bolts holding secondary protector plate in place. Relay is on the upper left. Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery Buss + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Pic3 Sportster 2004-2007

Incoming search terms:

Suzuki SV 650s OXFORD "Hot Grips" INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 14-02-2012

download
Installation of heated grips on motorcycles is popular in the UK since it’s not unheard of for even the “fair weather biker” to be caught out by a cold snap. Add to this the fact that many operations on a bike are performed by the hands and fingers, which will not perform well when frozen! 1) Before fitting the grips to the SV, a position must be chosen for the controller. The grips, needless to say, have their mounting places predetermined. I chose to make a small bracket for mounting on the top yoke. This allows the control box to sit level with the top surface for an integrated look whilst remaining accessible for operation. First of all- The mounting bracket in place: Picture shows a strip of rubber on either side of the bracket to stop rubbing / vibrations. Using the flat base and sticky pad supplied, mount the controller on the bracket. 2) With the easy bit done, we need to turn attention to the installation of the power feed cable. It would be too easy to leave the grips switched on with the bike parked up, or for kids to switch them on draining the battery and leaving you stranded. With this in mind, we really want to use a suitably rated power feed that is only “on” when the ignition key is turned on. Fortunately enough, the “pointy” SV has a couple of spare contacts in the fuse box which can be tapped for this purpose

Fitting Hondaline Heated Grips to Honda GL1800

0

Filed Under (Honda) by admin on 08-04-2011

download
Then remove the right side fairing trim piece, starting at the bottom inner and working your way upwards. Unscrew the single Allen head bolt holding the lock panel in place and remove the panel. Now to remove the old grips. Tip; If you have chrome cap ends fitted, protect the chrome on the screw by putting some tape on the end of the screwdriver If you’re a cheapskate, and want to save the old grips, run a thin screwdriver or a hacksaw blade around the inside of the grip to loosen the old glue and it will come away easily. Repeat on the right side grip. The Honda instructions tell you to remove the whole throttle grip & boss but you don’t need to go to all that hassle of unscrewing the switch assembly to get at it. Just remove the rubber grip same as described for the left side After removing the switch panel from the Goldwing, drill a 45mm hole with a holesaw. The spot to drill is marked on the inside of the panel. Then just screw the controller knob assembly into position with the three screws provided (second picture) Spread some glue (the Honda stuff if you can get it, or just plain old rubber cement as I’ve used on my last four Goldwings without problems). Spread it more towards the ends and middle of the bar as it will get pushed inward as you push the grips on anyway

Harley Davidson Motorcycles Hot Grips Installation Manuals

0

Filed Under (Harley Davidson) by admin on 23-02-2012

download
End weights or other need to open the ends: You may drill out the outboard ends of the grips for installation of end weights or other purpose, if you use a fine tooth hole saw and do not go larger than the handlebar’s inside diameter. We have molded in a visual guide on the grip’s ends, and we recommend 7/8″ or at most 1″ diameter and be sure to center drill carefully. DO NOT use a hacksaw or you will destroy the grip, because there are resistance wires molded into the grip outboard of the handlebar diameter. Some Harley throttle sleeves are molded with raised plastic ribs or ridges to help hold the original Harley grip in place, and these will mate up with four (4) of our internal ribs by sliding our heated handgrip over the sleeve. HOWEVER, there are two axial ribs, which go circumferentially around the throttle sleeve as illustrated below, and they may have to be carefully removed with a knife of razor blade. They must be trimmed off with a file or razor knife until the Hot Grips slides over them. Do not force the Hot Grips over the ridges as the grip cannot stretch and will be damaged if forced on. These Hot Grips® have a heat output of 8 watts on “low” and 15 watts on “high” per grip. As a pair they will consume 20 watts of electrical power on “low” and 30 watts on “high”. They consume more than 8 x 2 on “low” because the resistor consumes a little

HONDA CB1000R AKRAPOVIC SLIP-ON EXHAUST SYSTEM REMOVAL And Installation instructions

0

Filed Under (Honda) by admin on 01-11-2010

download
1. Put the motorcycle on a side stand, we recommend a racing stand. Make sure, that surface is solid and flat. 2. Untighten the bolt on the metal clamp at the muffler – collector joint, unscrew the bolts from the muffler brackets, and remove the muffler (Figure 1, 2, 3, 4). T-handle 8mm wrench T-handle 12mm wrench T-handle 13mm wrench T-handle 10mm swiveling wrench T-handle 12mm swiveling wrench T-handle 3mm three hexagon key wrench T-handle 5mm three hexagon key wrench T-handle 8mm three hexagon key wrench Combination 13mm wrench Combination 17mm wrench Spring puller Figure 1 Figure 2 Figure 3 Figure 4
NAV – 401 3 Figure 7 Figure 8 Figure 9 Figure 10 3. Remove the metal collar and the rubber damper from the lower stock muffler bracket (Figure 5, 6). 4. For open slip-on only: for easier dismount of stock collector unscrew the bolt from the water cooler hanging bracket and slightly remove the cooler – do not disconnect the cooling system tubes! (Figure 7) , loosen the header tubes flanges (Figure 8) , untighten the bolts of the metal clamps A from stock collector – header tubes joint and then unscrew the bolt from the collector bracket (Figure 9, 10). Make sure not to damage the cooling fins of the cooler during this process. Figure 5 Figure 6
NAV – 401 4 5. For open slip-on only: Unscrew the lambda sensor and remove the stock collector (Figure 11, 12). Remove the metal collar and the rubber dampers from the stock collector bracket (Figure 13). INSTALLATION OF THE AKRAPOVIC SLIP-ON EXHAUST SYSTEM: 1. Unsrew the bolts and remove the right foot peg. Assemble the additional Akrapovic metal bracket, reinstall the foot peg and tighten the bolts (Figure 14, 15, 16, 17, 18, 19)

Victory Electronic Jet Kit Installation Instructions

0

Filed Under (Victory) by admin on 31-10-2010

download
INSTALLATION ( at anytime during install or tuning please callus for any and all help, we can’thelpifyoudon’tcall ) 1. Before installing the TFI you must first disconnect the negative lead from the battery. 2. Determinea location for the TFI unit. Suggested locations areas follows: Under the seat, behinda side cover or tail section. 3. The TFIcomeswitha harness with injector connectors that match the factory injector connectors. 4. Locate the factory fuel injectors (see owners manual if you are not sure)*. If the TFIharness does not match your injectors do not proceed and call tech support at 877-764- 3337. 5. Disconnect the factory injector connectors from the fuel injectors and replace with the TFI injector connectors from the TFI unit, basically unhook the factory injector connector and plug the matching TFI connector (female) to the injector and then connect the factory injector connector to the TFI connector that simulates the injector (male). There is no order to hookup the TFI harness to the factory harness just make sure the original factory connector goes toits’original cylinder. It is a good idea to make sure there is a little slack in the harness to prevent engine vibration from damaging/breakingawireon the connectors. 6. Be sure to check the wires are not indirect contact with any sharp edges, exhaust and/or other objects, which could result in long term wear and/or damage. 7. Connect the TFI ground lead to the negative terminal of the battery along with the factory ground lead. 8. With the rubber plug removed from the TFI, turn the motorcycle key switch to the “ON”position. As the bikes electrical system goes through initial startup mode you may see LED’sflashingonthe TFI.

Incoming search terms:

Harley-Davidson Softail, Touring, Dyna, Sportster and V-Rod, SELF LEARNING MODULE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2012

download
STEP 1 – BATTERY CONNECTION Locate the battery and disconnect the negative battery cable. Mount the module in the open area in front of the battery with 2-tie straps or velcro straps, directing the harness from the module towards the 6 o’clock position. STEP 2 – THROTTLE POSITION SENSOR (TPS): Remove the air cleaner assembly and unplug the TPS sensor connector at the TPS sensor. The harness includes (2) TPS connectors which should be routed under the gas tank into the factory wire loom to the TPS sensor. The TPS sensor is located on the left side of the throttle body. Plug the (2) TPS connectors from the module in between the TPS sensor and to the factory TPS connector. STEP 3 – O2 SENSOR: Systems equipped with factory O2 sensors Rear: Unplug the Rear O2 sensor connector from the factory harness, which is located at the Rear exhaust pipe. Route the module’s harness which includes (2) O2 sensor connectors and connect one connector to the Rear O2 sensor and connect the other connector to the main factory O2 sensor connector. Front: Unplug the Front O2 sensor connector from the factory harness, which is located at the Front exhaust pipe. Route the module’s harness which includes (2) O2 sensor connectors, and connect one connector to the Front O2 sensor and connect the other connector to the main factory O2 sensor connector. Systems not equipped with factory O2 sensors NOTE: Many aftermarket exhaust systems are now equipped with plugged O2 sensor bungs which can be removed to accept an aftermarket O2 sensor. Typically these bungs already have a thread size of 18 mm x 1.5 mm. Exhaust systems not equipped with O2 sensor bungs need to have the supplied 18 mm x 1.5 mm thread size bung welded to the exhaust pipe in order to install an O2 sensor. The O2 sensor bung should be installed 3 to 6 inches away from the rear cylinder exhaust port and in front of the exhaust torque tube pipe area. The module prefers to receive information from the O2 sensor from an area that is NOT contaminated from atmospheric air. This air may enter through the tail pipe of an unrestricted or un-baffled exhaust pipe. The bung should not be installed in the “5 to 7 o’clock” area. If mounted in this area the O2 sensor can be damaged. The moisture from the gases exiting from the rear cylinder exhaust port will harm the ceramic shell element of the O2 sensor.

Incoming search terms: