free 1974 hd sporster ironhead motor diagram

You search Auto repair manual PDF free 1974 hd sporster ironhead motor diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  free 1974 hd sporster ironhead motor diagram Direct Download speed 5282 Kb/s

  free 1974 hd sporster ironhead motor diagram Full Version speed 6162 Kb/s



1995 Camry WIPER MOTOR CIRCUIT BREAKER INSPECTION PROCEDURE

0

Filed Under (Toyota Manuals) by admin on 15-10-2011

download
INSPECTION PROCEDURE: Inspect the Wiper Fuse. Verify there is power and ground to the Wiper Motor on all speeds (including “Intermittent” or “Mist” if applicable). After verifying power and ground to the Wiper Motor, follow the procedure below to prevent unnecessary Wiper Motor replacement because of a temporary open in the Wiper Motor Circuit Breaker. 1) Disconnect the Wiper Motor Harness Connector. 2) Wait (10) minutes before checking continuity. 3) Check the continuity of the motor with an ohmmeter. REPRESENTATIVE CHECKING PROCEDURE: NOTE: Continuity check can be performed between either the low speed or high speed terminal and the ground terminal of the wiper motor. The standard resistance of a good wiper motor is approximately 1.5 to 4.5 ohm

Incoming search terms:

Commonwealth of Massachusetts Registry of Motor Vehicles Motorcycle Manual

0

Filed Under (Tips and Review) by admin on 18-11-2010

download
DEFINITIONS MOTORCYCLE Any motor vehicle having a seat or saddle for the rider that is designed to travel with no more than three wheels contacting the ground, including any bicycle with a motor or driving wheels attached. MOTORIZED BICYCLE A pedal bicycle which has a helper motor, or a non-pedal bicycle which has a motor, with a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission, and which is capable of a maximum speed of no more than thirty (30) miles per hour (mph) . OPERATION OF MOTORIZED BICYCLES Under Massachusetts law, mopeds fall into the category of “motorized bicycles”(with or without pedals) and are therefore regulated by the Registrar of Motor Vehicles. Individuals must have a valid learner’s permit or driver’s license to operate a motorized bicycle or moped. Mopeds must have automatic transmissions and cylinder capacities of no more than 50 cubic centimeters. In addition, mopeds must meet all federal motor vehicle safety standards and have maximum speeds of no more than 30 mph. The following limitations apply:  Individuals may not operate at speeds greater than 25 mph;  Individuals may not operate on state highways or limited- access roads with signs prohibiting bicycles;  Individuals may not operate on off-street recreational paths;  Individuals may use bicycle lanes along roadways;  Individuals must use the proper hand signals before stopping or turning;  Individuals and their passengers must wear United States Department of Transportation (US DOT) approved helmets when operating;  Individuals may not carry passengers while operating on a permit.

Incoming search terms:

TRIUMPH ROCKET III TIP OVER BARS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-12-2010

download
1. Starting on the right side (towards the front of the motor) locate the three mounting bolts that secure the brake assembly bracket (a chrome tube) to the bottom of the motor. Remove the bottom and front bolts. Repeat for left side. 2. Locate the front motor mount bolt. This is the black bolt located at the very front of the engine about halfway down behind the radiator. Remove the nut from this bolt on the left side. Properly secure the bike and use a jack to lift up on the motor to release the pressure from the motor mount bolt. Remove the bolt. 3. On the right side place the motor mount bolt thru the upper mounting hole of the right tip over bar. Install the tip over bar by feeding the motor mount bolt thru the original hole and inserting the two bolts (supplied) into the bottom mounting holes. (Do not tighten yet.) 4. On the left side install the top of the left tip over bar by inserting it into the right side tip over bar. Align the tip over bar so that the motor mount bolt extends thru the upper mounting hole. Thread the original locking nut onto the motor mount bolt a couple of turns. Now align the bottom of the tip over bar and install the remaining two bolts (supplied). Tighten the motor mount bolt (torque to 28-32 ft/lbs) and the lower four bolts (torque to 14-18 ft/lbs) securely. 5. Re-check all hardware for tightness

Incoming search terms:

KAWASAKI Z1000 GTR Electronic Cruise Control Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The actuator spool is installed in the CIU housing with the actuator cable. The actuator spool is rotated to fully extend the cable. 2nd step. The dual spool and carburettor cable are installed. The carburettor cable is attached to the lower groove in the dual spool. The other end of the carburettor cable is attached to the carburettors. Note the position of the roll pin. It is nearly contacting the end of the groove in the actuator spool. The free play in the carburettor cable must be adjusted so that the cable outer can be pulled out 2 ~ 3mm before the carburettors start to open. This ensures that the cruise control cannot prevent the carburettors returning to idle. If more free play is allowed the response of the cruise control is compromised. This adjustment of free play is usually performed after final assembly of the CIU is completed and the CIU is in its final location. This is because flexing the cable affects the free play. It is shown at this stage in these diagrams to improve clarity. After this adjustment is performed, the carburettor cable adjustment MUST NOT BE MOVED. All future adjustments of free play in the throttle must be performed on the throttle cable from the throttle grip. If incorrect free play in the carburettor cable is suspected due to inconsistent cruise operation or because of inconsistent idle speed, the adjusters on the throttle cable from the hand grip must be backed all the way off to give as much free play as possible. If this does not result in AT LEAST 5mm of free play in the throttle cable, the throttle cable must be removed from the hand grip or CIU before adjustment of the carburettor cable is attempted. This is crucial because the amount of free play in the throttle cable also affects the apparent free play in the carburettor cable

Incoming search terms:

BMW K1100 RS/ RT/ LT ABS 2 Electronic Cruise Control Installation Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
The actuator spool is installed in the CIU housing with the actuator cable. The actuator spool is rotated to fully extend the cable. 2nd step. The carburettor cable and spool are installed and the other end of the carburettor cable is attached to the carburettors. Note the position of the roll pin. It is nearly contacting the end of the groove in the actuator spool. The free play in the carburettor cable must be adjusted so that the cable outer can be pulled out 2 ~ 3mm before the carburettors start to open. This ensures that the cruise control cannot prevent the carburettors returning to idle. If more free play is allowed the response of the cruise control is compromised. This adjustment of free play is usually performed after final assembly of the CIU is completed and the CIU is in its final location. This is because flexing the cable does effect the free play. It is shown at this stage in these diagrams to improve clarity. After this adjustment is performed, the carburettor cable adjustment MUST NOT BE MOVED. All future adjustments of free play in the throttle must be performed on the throttle cable from the throttle grip. If incorrect free play in this cable is suspected due to inconsistent cruise operation or because of inconsistent idle speed, the adjusters on the throttle cable from the hand grip must be backed all the way off to give as much free play as possible. If this does not result in AT LEAST 5mm of free play in the throttle cable, the throttle cable must be removed from the hand grip or CIU before adjustment of the carburettor cable is attempted. This is crucial because the amount of free play in the throttle cable also effects the apparent free play in the carburettor cable.

Incoming search terms:

New Automatic Transmission for Motorcycles Human-Friendly Transmission

0

Filed Under (Honda) by admin on 18-12-2011

download
High-pressure fluid flow The engine rotates the pump swash plate, which has a gear mechanism. The rotating swash plate pushes the pump pistons to increase the pressure on the hydraulic fluid and feed it to the high-pressure annular chamber. The high- pressure fluid is then fed to the oil motor piston chamber where it pushes the pistons forward, which then push the motor swash plate. Power Fluid flow from pump to motor Fluid flow from motor to pump Low-pressure fluid flow The lower-pressure hydraulic fluid returns to the pump through the low-pressure annular chamber. In this way, the fluid circulates between the pump and the motor. Movement of distributor valves and pistons The distributor valves play an important role in fluid circulation. The valves are placed both in the oil pump and motor. When the pump pistons move to the compression side, the valves connect the piston chamber and the high- pressure chamber. When the pump pistons move to the expansion side, the valves allow a connection between the piston chamber and the low-pressure chamber. The valve in the oil motor moves opposite to its counterpart in the pump, ensuring the circulation of fluid within the system

Incoming search terms:

YAMAHA MOTOR CORPORATION, U.S.A. STREET & ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 27-12-2011

download
GENERALEXCLUSIONS from this warranty shall include any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. Areasonable dealer imposed fee may be charged for the inspection. In no case will warranty be extended beyond the original period. EMISSIONS CONTROLSYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

Incoming search terms:

Yamaha XVS 650AN Supplementary Service Manual

0

Filed Under (Yamaha) by admin on 15-12-2010

download
MAINTENANCE SPECIFICATIONS ENGINE Item Standard Limit Connecting rod: Oil clearance Color code (corresponding size) 0.031 0.055 mm (0.0012 0.0022 in) Blue Black Brown Green CHASSIS Item Standard Limit Front suspension: Front fork travel Fork spring free length Installed length Spring rate (K1) Stroke (K1) Optional spring Oil capacity Oil level Oil grade 140 mm (5.5 in) 332.5 mm (3.1 in) 287.4 mm (11.3 in) 3.43 N/mm (0.343 kg/mm, 19.2 lb/in) 0 140 mm (0 5.5 in) No 0.507 L (17.4 US oz) 95 mm (3.74 in) Yamaha fork oil 10 WT or equivalent 325.9 mm (12.83 in) Front brake: Type Disc outside diameter thickness Pad thickness inner Pad thickness outer Master cylinder inside diameter Caliper cylinder inside diameter Caliper cylinder inside diameter Brake fluid type Single disk 298 5 mm (11.73 0.2 in) 6.0 mm (0.24 in) 6.0 mm (0.24 in) 14.0 mm (0.55 in) 30.2 mm (1.19 in) 33.3 mm (1.31 in) DOT 4 4.5 mm (0.18 in) 0.8 mm (0.03 in) 0.8 mm (0.03 in) Brake lever & brake pedal: Brake lever free play (at pivot) Brake lever free play (at lever end) Brake pedal position Brake pedal free play Clutch lever free play (at pivot) Clutch lever free play (at lever end) 1 2 mm (0.04 0.08 in) 10 15 mm (0.39 0.59 in) 108 mm (4.25 in) 20 30 mm (0.79 1.18 in) 2 3 mm (0.08 0.12 in) 10 15 mm (0.39 0.59 in) -4- MAINTENANCE SPECIFICATIONS SPEC ELECTRICAL Item Standard Limit T.C.I.: Pickup coil resistance/color T.C.I. unit model/manufacturer 182 222 Ω at 20C (68F)/Gray – Black J4T088/MITSUBISHI (U.S.A) J4T128/MITSUBISHI (CAL) Ignition coil: Model /manufacturer Minimum spark gap Primary winding resistance Secondary winding resistance F6T541/MITSUBISHI 6 mm (0.24 in) 3.6 4.8 Ω at 20C (68F) 10.7 14.5 kΩ at 20C (68F) Voltage regulator: Type Model /manufacturer No load regulated voltage Semi-conductor, short-circuit type SH650C-11/SHINDENGEN 14.1 14.9 V Rectifier: Model /manufacturer Capacity Withstand voltage SH650C-11/SHINDENGEN 18 A 200 V Electric starter system: Type Starter motor: Model /manufacturer I.D. number Output Brush overall length Commutator diameter Mica undercut Starter relay: Model /manufacturer Amperage rating Constant mesh type SM-13/MITSUBA SM-13 0.7 kW 10 mm (0.39 in) 28 mm (1.10 in) 0.7 mm (0.08 in) MS-5F-441/JIDECO 180 A 4 mm (0.16 in) 27 mm (1.06 in) Flasher relay: Type Model /manufacturer Self cancelling device Flasher frequency Wattage Semi transistor type FB257H/DENSO Yes 75 95 cycle/min 27 W 2 + 3.4 W Fuel pump relay: Model /manufacturer G8R-30Y-Q/OMRON

Incoming search terms:

HARLEY DAVIDSON ADVANCED AUDIO HANDS FREE PHONE INTERFACE KIT INSTALLATION

0

Filed Under (Harley Davidson) by admin on 12-04-2011

download
The Hands Free interface module in this kit requires proximity to a BluetoothTM-enabled cellular phone in order to function. The phone must be a model that is compatible with the interface module (go to to view the compatibility chart), and must be paired to the interface module according to the instructions included with the cell phone. NOTE The cell phone MUST be available to the installer in the final steps of the installation (prior to re-installation of the outer fairing) in order to program and test the hands free functions. To avoid unnecessary delays, please take this into consideration when scheduling the installation. FLHT models will require prior installation of an Advanced Audio AM/ FM/ CD Radio Kit (Part Number 76412-06) and a Tour-Pak Mount AM/ FM Antenna Kit (Part Number 76317-06). FLHT, FLHX and FLTR models will require the prior installation of a Tour Pak®. See a Harley-Davidson dealer for avail- ability of color-matched King or Chopped Tour-Paks to match your vehicle, and additional items that may be required when mounting the Tour-Pak to your model. Unless one has already been fitted as part of another Advanced Audio kit installation: FLHTCU models will require the additional purchase of an Ultra Overlay Harness (Part Number 70164-06). FLHT, FLHTC and FLHX models will require the separate purchase of a Communication Switch Kit (Part Number 77173- 06). FLHX models will require the separate purchase of: •a fuel tank console (Part Number 61270-98A), •a console extension (Part Number 52447-96), •a rubber molding (71294-89), •a 1/4-20 clip nut (Part Number 7964), •a button-head screw (Part Number 3652), •a plastic wire clip (Part Number 10120), and •an adhesive-backed metal wire clip (Part Number 10103). FLTR models will require the separate purchase of: •a Console Pod Assembly (Part Number 77136-03), and •three pan-head screws (Part Number 2462). NOTE See a Harley-Davidson dealer for availability of optional decorative inserts for the Console Pod Assembly. ALL models will require the additional purchase of: •a Non-Ultra Overlay Harness (Part Number 70169-06), and EITHER : •a Premium Stereo Helmet Headset (Part Number 77147- 98) OR a Hand-Held CB Microphone Kit (Part Number 76312-98

Incoming search terms:

1992 Toyota Cressida Vehicle Wiring Chart and Diagram

0

Filed Under (Toyota Manuals) by admin on 18-06-2011

Download
Listed below is the vehicle specific wiring diagram for your car alarm, remote
starter or keyless entry installation into your 1992 Toyota Cressida . This
information outlines the wires location, color and polarity to help you identify the
proper connection spots in the vehicle. Please be sure to test all of your wires
with a digital multimeter before making any connections. More information on
using a multimeter and testing wires please see our Technical Support Area.

Incoming search terms:

Incoming search terms: