free manual kawasaki voyager 1200 pdf

You search Auto repair manual PDF free manual kawasaki voyager 1200 pdf, if there are search results will appear below. If search results do not exist, please search by others keyword.



  free manual kawasaki voyager 1200 pdf Direct Download speed 5282 Kb/s

  free manual kawasaki voyager 1200 pdf Full Version speed 6162 Kb/s



Kawasaki Voyager Installation And Removal Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Review entire installation manual Remove saddle bags and rear fender cover Modify rear fender bolt slots Install receiver hitch and double check all bolts Remount saddle bags Assemble InstaTrike hitch cart Attach InstaTrike to motorcycle via receiver hitch Attach leanstop brace bolts to receiver hitch Align InstaTrike wheels Double check all bolts for tightness Test ride InstaTrike slowly in an open area to familiarize yourself with handling characteristics Receiver Hitch Installation INSTALL ALL BOLTS AND BRACKETS LOOSLEY UNTIL ALL COMPONENTS ARE IN PLACE! 1) Place motorcycle on its center stand 2) Remove saddle bags and rear fender 3) At the bottom of the rear fender locate two bolt slots. (bolts were removed from these when rear fender was removed) Open the front end of these slots in order to remount fender. 4) Replace bottom fender bolts about 2 or 3 turns. This is necessary to be able to remount rear fender. 5) Attach bracket A to motorcycle. Locate two threaded holes (6mm) near the top of the sub frame. Bolt top of bracket A to these holes. ( bolts provided ) 6) Attach bracket B ( left side ) / C ( right side ) to motorcycle by replacing the bolt that holds the muffler to the frame and vibration absorber with the new bolt provided. Bracket B/C mounts on the outside of the large chrome washer. 7) Attach brackets A, B, C to the hitch ( top ) 8) Replace rear fender 9) Attach brackets D and E to the motorcycle sub frame with U- bolts provided. Attach brackets to hitch. 10) Tighten all bolts and double check. 11) Reinstall saddle bags

Incoming search terms:

HARLEY DAVIDSON ADVANCED AUDIO COMMUNICATION SWITCH KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 2. Refer to the instructions included with the Advanced Audio Hands Free Phone Interface, CB Radio or Intercom Kit, and proceed with that installation until the installation of the items in this kit is called for. 3. Remove the outer fairing and windshield. Refer to OUTER FAIRING/ WINDSHIELD REMOVAL in the Service Manual. 4. On the fairing cap, remove the inner left side hole plug. See Figure 1 and the FAIRING CAP SWITCHES (FLHTC/U) section in the Service Manual. Install the fairing speaker switch (4) in the opening as follows: If a cruise control switch IS present: Follow the instructions in the Service Manual to install the speaker switch. If a cruise control switch IS NOT present: a. Obtain the speaker switch adapter wire (5) from the kit, and the butt splice connector included with the speaker switch. b. Refer to SEALED BUTT SPLICE CONNECTORS in the Service Manual. Splice the adapter wire to the black/ green speaker switch lead. c. Insert the terminated end of the adapter wire into cavity 12 of the fairing cap switch connector [105B] 5. Remove the original equipment left-hand control switch assembly per the HANDLEBAR SWITCHES, REMOVAL, LEFT HANDLEBAR CONTROLS instructions in the Service Manual. 6. Install the new left-hand control switch assembly (3) from the kit. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 7. ALL models: Install the console pod assembly (1), and route the harness forward into the fairing per the instructions packaged with the Advanced Audio Hands Free Phone Interface, CB Radio or Intercom Kit. Be sure that steering is smooth and free without interference. Interference with steering could result in loss of vehicle control and death or serious injury. (00371a) • Be sure the wires do not pull tight when handlebars are turned fully to left or right fork stops. 8. Unless already installed, install the overlay harness per the instructions packaged with the Hands Free Phone Interface, CB Radio or Intercom Kit. 9. Refer to the Service Manual and follow the instructions given to re-install the Maxi Fuse

Incoming search terms:

2009 Kawasaki Voyager Heated Grips Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove the Factory Grips Before removing the factory grips, the”chromed plastic”grip end caps need to be removed. The chromed plastic ends are threaded on, but have”left hand”threads, which means to unscrew you need to turn them clockwise. (The opposite way that you would normally unscrew something) To do that I recommend using, either a rubber strap wrench, ora sheet of thin rubber used as you would to loosen the lid of ajar. Once Ihadtheend caps off, I used a sharp utility knife to cut through, and peel off the factory rubber grips. (They are only about 1/8″thicksoit’seasytodo.) With the rubber grips off, I removed the chromed ring that is adjacent to the left switch housing. The left ring will come off, witha gentle pull, but the throttle side ring will need to be cutoff, as it’s pressed on. It’seasytodo; I cut it off using wire side cutters (see picture on page 3 below). 2 Factory left and right Grips After removing the chromed end cap, and the factory rubber grips. The chromed plastic ring next to the switch housing needs to be cut off. Note all the ridges on the sleeve, all these except one ridge need to be filed off. 1. Prepare left handlebar for grip installation The left handlebar is pretty easy to prepare, first I cleaned any glue from the bar, and then gently test fit the left grip, be very careful here as it needs to slide on easily. Asper the instructions, ” Do not force the grip on with anything greater than gentle hand force “. Remember after the test fit you need to take it off again. (You could also crack the heated grip if it’stootight). If you find it too tight, as I did sand the bar using sandpaper until it slides on and off easily. On my bike I used an 80 grit sandpaper, and it took approx 20 minutes to geta good fit

Incoming search terms:

KAWASAKI Z1000 GTR Electronic Cruise Control Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The actuator spool is installed in the CIU housing with the actuator cable. The actuator spool is rotated to fully extend the cable. 2nd step. The dual spool and carburettor cable are installed. The carburettor cable is attached to the lower groove in the dual spool. The other end of the carburettor cable is attached to the carburettors. Note the position of the roll pin. It is nearly contacting the end of the groove in the actuator spool. The free play in the carburettor cable must be adjusted so that the cable outer can be pulled out 2 ~ 3mm before the carburettors start to open. This ensures that the cruise control cannot prevent the carburettors returning to idle. If more free play is allowed the response of the cruise control is compromised. This adjustment of free play is usually performed after final assembly of the CIU is completed and the CIU is in its final location. This is because flexing the cable affects the free play. It is shown at this stage in these diagrams to improve clarity. After this adjustment is performed, the carburettor cable adjustment MUST NOT BE MOVED. All future adjustments of free play in the throttle must be performed on the throttle cable from the throttle grip. If incorrect free play in the carburettor cable is suspected due to inconsistent cruise operation or because of inconsistent idle speed, the adjusters on the throttle cable from the hand grip must be backed all the way off to give as much free play as possible. If this does not result in AT LEAST 5mm of free play in the throttle cable, the throttle cable must be removed from the hand grip or CIU before adjustment of the carburettor cable is attempted. This is crucial because the amount of free play in the throttle cable also affects the apparent free play in the carburettor cable

Incoming search terms:

HARLEY DAVIDSON VRSC CHROME WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2011

download
Installation To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1 WARNING 1 WARNING ® Kit Numbers 41279-04, 41282-04, 41463-05, 41467-05, 41633-05, 41634-05, 41640-05, and 41639-05 1 of 3 Figure 1. Rear Wheel Removal i02495 1. Axle (keep) 2. Axle adjuster (keep) 3. Axle nut (keep) 4. “E”-clip (keep) 5. Spacer (3) (keep) 6. Torx screw (5) (replace) 7. Brake disc (keep) 8. Wheel assembly (replace) 9. Valve cap (keep) 10. Compensator bowl (keep) 11. Compensator cushion (keep) 12.12 pt screw (5) (keep) 13. Lockwasher (5) (keep) 14. Sprocket assembly (keep) 1. Refer to the Service Manual and follow the MAXI-FUSE instructions to remove the right-side cover and maxi- fuse. Proceed to Step 2 for the wheel being replaced. Rear Wheel 2. See Figure 1. Remove the rear wheel per the REAR WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. 4. Re-assemble all saved components to the new chrome rear wheel assembly. See REAR WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Fasten the brake disc to the valve stem side of the wheel using the Torx®screws from the kit. Install the compensator bowl with the 12-point screws and lockwashers saved earlier. 6. Install the new wheel to the rear fork. Refer to REAR WHEEL, INSTALLATION in the Service Manual. Proceed to Step 7. Front Wheel 2. See Figure 2. Remove the front wheel per the FRONT WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Mark the left and right brake discs so they can be re-installed to the same location. 4. Re-assemble all saved components to the new chrome front wheel assembly. See FRONT WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Using the Torx ® shoulder bolts from the kit, and the saved spring washers fasten the brake discs to the same side of the wheel from which they were removed. 6. Install the new wheel to the front forks per the FRONT WHEEL, INSTALLATION instructions in the Service Manual. Proceed to Step 7. Front and Rear Wheels 7. Refer to the Service Manual and follow the MAXI-FUSE instructions to replace the maxi-fuse and right-side cover. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) After servicing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a) Maintenance and Cleaning Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley Wheel and Tire Cleaner, part number 94658-98, applied with Harley Wheel and Spoke Brush, part number 43078-99. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner, part number 94683-99. 3. After cleaning and polishing, seal the finish with a good quality sealer such as Harley Glaze Polish and Sealant, part number 99701-84

Incoming search terms:

SUZUKI GSX-R1000 SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 12-11-2010

download
Cover the throttle bodies to prevent anything from dropping into the engine. 1. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box. (Refer to Service Manual, Page 5-14) 4. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation. 5. Install the air cleaner box in reverse order of removal. (Refer to Service Manual, Page 5-14) 6. Lower the fuel tank. (Refer to Service Manual, Page 5-3) 7. Remove the upper seat rail plate. Disconnect and remove the ECM. (Figure 1) @ ISC Valve Mounting Screw Torque: 2.1± ±0.6 N.m (1.5± ±0.4 lb-ft) ! Carefully insert the ISC valve straight into the throttle body hole to prevent damaging the o-ring. Turn the ISC valve slightly to confirm that the o-ring has not twisted. Using the new screw provided in the replacement parts kit, make sure the screw is completely seated on the plate after the screw has been tightened to the specified torque. 4. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation. ! Cover the throttle bodies to prevent anything from dropping into the engine. 1. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box. (Refer to Service Manual, Page 5-14) REPLACEMENT PROCEDURE: 8. Install the new ECM in reverse order of removal. Apply thread lock to the upper plate mounting bolts when reinstalling the upper seat rail plate.

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE TWIN CAM 110 (1800 CC) CONVERSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
REMOVAL Prepare for Service 1. Position motorcycle on a suitable lift. NOTE If vehicle is equipped with Harley-Davidson Smart Security System, see owner’s manual for instructions to disarm the system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery cables, negative (-) battery cable first. 3. Remove seat according to the instructions in the service manual. 4. Refer to service manual to remove left saddlebag and side cover. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 5. Remove fuel tank according to the instructions in the service manual. Remove Engine Components 1. Remove existing air cleaner assembly. Discard backplate but save remaining parts. Refer to AIR CLEANER REMOVAL in service manual. 2. Remove existing exhaust system. Refer to EXHAUST SYSTEM REMOVAL in service manual. 3. Remove engine from chassis following the instructions in the service manual. 4. Disassemble engine top end and bottom end. Refer to appropriate ENGINE sections in service manual. 5. Remove existing clutch diaphragm spring. Refer to CLUTCH REMOVAL in service manual. The procedures in this instruction sheet should be performed by one experienced in precision measuring techniques. Failure to meet tolerances called for in this instruction sheet can result in engine damage. (00511b) -J04793 1 2 is03517 1. O-ring counterbore 2. Spigot bore Figure 1. Spigot Bore and O-Ring Counterbore Dimensions Table 1. Spigot Bore and O-Ring Counterbore Dimensions Depth Bore Description 1.625 +/- 0.010 in. (41.3 +/- 0.25 mm) 4.205 +/- 0.010 in. (107 +/- 0.25 mm) Spigot Bore 0.085 +/- 0.003 in. (2.16 +/- 0.08 mm) 4.415 +/- 0.002 in. (112 +/- 0.05 mm) O-Ring Counter- bore is03456 Figure 2. Cylinder Wall MACHINE CRANKCASE Crankcase Boring Preparation NOTE During final assembly of the engine, Harley-Davidson recommends replacing the OE cylinder studs with Screamin’ Eagle High Tensile Studs (16505-01). 1. Remove cylinder studs from the engine crankcase. 2. Mask off all bearings and oil holes to prevent debris and contaminants from entering those areas. 3. Inspect and clean engine case mating surfaces. 4. See Figure 6. Reassemble engine case with OE screws, except the top center screw between the cylinders, and tighten to specifications listed in service manual. NOTE To prevent damage to crankcase boring tool, it is important to replace the top center screw with a modified top center screw (1093). This screw is included in the Crankcase Boring Tool Kit (94419-06) and can be purchased separately from a Harley- Davidson dealer. 5. Install modified top center screw (1093) between the cylinders and tighten to 50-90 in-lbs (5.6-10.2 Nm). 6. See Figure 1 and Table 1. Machine crankcase cylinder spigot bore and O-ring counterbore to the dimensions shown. Modify Crankcase

Incoming search terms:

2004-2007 Kawasaki STX-15F Supercharger Kit installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
ENGINE REMOVAL: 1. Turn ignition off, remove lanyard, disconnect battery cables and remove battery. 2. Remove engine following steps outlined in section 7 of Kawasaki service manual. NOTE: Replace oil filter if engine was run previously. Please recycle used oil and oil filter. NOTE: Clear an area on a sturdy workbench or heavy-duty cart to place engine after removal. Be sure to carefully place engine on a smooth surface so as not to damage oil pan. It is recommended that you have assistance for the engine removal process. 3. Replace stock pistons, rings, piston pins, clips, cylinder head gasket and cylinder base gasket with supplied forged pistons, rings, piston pins, clips, cylinder head gasket and cylinder base gasket following the steps outlined in section 6 of the Kawasaki service manual. NOTE: This is an involved process requiring advanced mechanical skills and 4-stroke engine experience. DO NOT ATTEMPT if you are not mechanically inclined or familiar with 4-stroke engines. 4. Remove OE crankshaft coupler and discard. 5. Locate boss on PTO housing just above crankshaft. Cut off at a 45° angle. (See page 1 of Installation Images) NOTE: Cover end of crankshaft. Thoroughly clean engine afterwards. EXHAUST SYSTEM MODIFICATIONS: 6. Inside hull under rear grab handle remove air inlet tubes. Disconnect hoses for stock bilge pick-ups from breather fittings. (see illustration #1) 7. Remove exhaust hose connecting primary muffler (left water box) to secondary muffler (right water box). Disconnect remaining hoses from breather fittings. Remove exhaust hose connecting secondary water box to exhaust outlet. (see illustration #2) NOTE: Retain hose clamps. 8. Remove section of foam between top deck and pump area and discard. 9. At rear of hull remove and discard plastic exhaust outlet nozzle. Remove exhaust outlet, cut 5-3/4″ from end of flange and weld a bead around modified end of exhaust outlet. (see illustration #3) NOTE: Sand or file edge after modifying. 10. Install one supplied silicone coupler onto modified exhaust outlet and secure using OE hose clamp. (see illustration #4) Install exhaust outlet into hull and secure using stock hardware. (see illustration #5) NOTE: Be sure rubber gasket is in place between flange and hull. Do not use any sealant. Apply blue Loc-tite to bolts. Do not over tighten bolts. 11. Install supplied billet exhaust outlet tip using supplied hardware. (see illustration #6) NOTE: Apply blue Loc-tite to bolts. Do not over tighten bolts.

kawasakI 9400 hyPercharger kIt INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
steP 1 Remove the seat. steP 2 Remove the bottom of the three dash plaque bolts (8mm). steP 3 Lift up on the dash panel and unscrew the speedometer cable (knurled nut). steP 4 Unplug the three electrical connections. steP 5 With a 12mm socket, remove the tank-mounting bolt under the dash and at the rear of the tank. steP 6 Close the fuel valve and clamp off the fuel line. Disconnect the line from the fuel valve. steP 7 Raise the rear of the tank, and disconnect the two vent hoses, and remove the tank. steP 8 Refer to the section of your factory service manual that deals with removal and installation of the following components. • Remove the two round chrome “air cleaner covers”, their backing plates, the stock black plastic air box (air inlet under tank), and the crossover tube. • Remove the intake manifold to remove and crossover tube. Use extreme care when replacing the intake manifold. Uneven torque, damage to the intake gaskets, or contamination can cause an intake leak that will result in very poor running, and nearly impossible jetting!! • Unplug all hoses or lines from these components. You may want to label these hoses at this time. The Largest of these hoses (3/4″ I.D.) is for the fresh air injection system; the second largest (3/8″ I.D.) is the crankcase breather. The smallest of the hoses is a drain. steP 9 Remove the brackets that held each round backing plate. The right hand bracket is also a carb stabilizer. This function is duplicated with one of the included brackets. steP 10 Remove the carburetor according to the section in your factory service manual that outlines procedures for carburetor removal, disassembly, reassembly and installation. We recommend that you label each hose or fitting as they are removed to make reassembly easier. An example of hose labeling is shown in PIC. 1. carburetor re-jettIng Procedure note Different combinations of aftermarket exhaust and air cleaners will have a significant impact on carburetor jetting. The supplied jetting components have been tested and found to be a good combination to produce drivability and performance with stock or free flowing, muffled/baffled exhaust pipes. We highly recommend NOT using drag pipes (open style). Using drag pipes in conjunction with our air cleaner will require additional jetting above and beyond the components included in this kit. a) Consult your factory service manual for details of this procedure. We have supplied jets to cover many common configurations. Remove the four Phillips head screws securing the plastic carb top to the carb body. Carefully remove the plastic carb top making sure not to damage the rubber diaphragm.

HARLEY DAVIDSON SOFTAIL 6 SPEED TRANSMISSION – COMPLETE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
Removal of Original Transmission 1. Position motorcycle on a suitable lift. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. 3. Refer to the TRANSMISSION CASE REMOVAL in the Service Manual and follow the instructions given to remove the components with the following steps. 4. Refer to PRIMARY CHAINCASE COVER REMOVAL in the Service Manual and follow the instructions given to remove the primary chaincase cover. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 5. See the PRIMARY CHAIN and COMPENSATING SPROCKET REMOVAL in the Service Manual and use the instructions given to remove the primary drive assem- bly. 6. Refer to the STARTER REMOVAL in the Service Manual and remove the the starter. 7. See the VEHICLE SPEED SENSOR section and unplug the vehicle speedometer sensor connection and remove the mounting bolt. Lift sensor from the transmission case and set aside for later re-installation. 8. Refer to NEUTRAL SWITCH and disconnect the connectors from the neutral switch. 9. Refer to PRIMARY CHAINCASE in the Service Manual and follow the instructions given to remove the primary chaincase housing. 10. Refer to EXHAUST SYSTEM in the Service Manual and remove the exhaust. 11. See the REAR WHEEL REMOVAL and loosen but, do not remove rear axle to relieve drive belt tension and remove the belt from the sprocket from the transmission. 12. Refer to OIL TANK REMOVAL in the Service Manual and follow the instructions given to drain, remove the oil tank and detach the vent, feed and return lines. 13. Refer to CLUTCH CONTROL in the Service Manual and follow the instructions given to remove the clutch cover and disconnect the clutch cable end from the cover. Set the cable aside for later re-installation

Incoming search terms:

Incoming search terms: