fuelpak settings chart

You search Auto repair manual PDF fuelpak settings chart, if there are search results will appear below. If search results do not exist, please search by others keyword.



  fuelpak settings chart Direct Download speed 5282 Kb/s

  fuelpak settings chart Full Version speed 6162 Kb/s



Yamaha Road Star Warrior Fuel Injected Models INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove seat and fuel tank. 2. Remove airbox and left airbox cover. We highly recommend you consult the factory service manual for proper removal of airbox. 3. Route wiring harness under frame bracket towards airbox. (Fig 1) 4. Unplug stock black connector for fuel injectors. (Fig 2) 5. Plug Fuelpak 4-pin connectors in-line with the connectors from step 4. 6. Unplug the TPS connector and attach T-tap connector to the center wire (yellow). (Fig 3) 7. Route the Fuelpak violet wire to T-tap. (Fig 4) 8. Reattach the TPS connector. 9. Route black wire to the front of engine and down to the horn. (Fig 5) 10. Disconnect the factory black/white wire from horn. Plug Fuelpak into horn and plug Fuelpak black/white wire to Fuelpak connector. 11. Route black and green wires to battery negative. 12. Attach Fuelpak to Fuelpak harness and mount under seat as shown. (Fig 6) 13. Before reassembling the bike, make sure handlebar switch is in the engine-not-running position and turn the key on. Fuelpak should light up. Sound the horn. If Fuelpak turns off when the horn is sounded, recheck the black wire connection on the horn and that it is connected to the correct wire from the factory harness. 14. Follow the service manual to reinstall the airbox and gas tank. INSTALLATION INSTRUCTIONS FOR P/N 65005 READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION FUEL INJECTION MANAGEMENT SYSTEM ROAD STAR WARRIOR NOTICE: Fuelpak is intended for racing or off-highway use only, and is not legal for sale or use in California on pollution-controlled vehicles. PLEASE NOTE: FUELPAK USE REQUIRES A HIGH PERFORMANCE AIR FILTER. HOW IT WORKS ENTERING VALUES 1. Remove Fuelpak clear case cover by removing all four screws, save hardware . 2. Turn on main power with key, but do not start engine. Fuelpak display should light up, if not, turn power off and verify the connectors are fully seated. 3. Refer to Fuelpak Setting Reference to locate the Setting Values specific to your bike and exhaust system. If you do not find your setting, visit fuelpakfi.com or call tech support at (562) 921-0071. 4. Starting with mode 1 selected, press the value (+) or the value (-) buttons to input the correct value as indicated in your Setting Value. After entering your first value, press the mode select button to move to mode 2 and enter the value. Continue until you have entered the value for each of the first 18 mode positions. Each time the value (+) is pressed, the value increases by one number. Each time the value (-) is pressed, the value decreases by one number. (Please refer to the “How It Works” section directly above if you have questions about this step. 5. As the next procedure, after you have entered in your values for the first 18 modes, press the mode select button to move to mode 19. Fully twist open the throttle and return to idle position to calibrate the Fuelpak to your bike. 6. By pressing the mode select button twice, move to mode 21 and verify that it reads “0″ with the throttle closed, “50″ at approximately half-throttle and “99″ when fully opened; if not, repeat step 5. Do not proceed to step 7 until mode 21 is verified. 7. Enter any other mode values as required for your application. 8. Turn off power. 9. Reinstall clear cover, tuck Fuelpak under seat area and reinstall seat. 10. You are now ready to ride.

Incoming search terms:

YAMAHA ROADLINER / STRATOLINER Fuel Injected INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 28-10-2010

download
1. Be sure the main switch is in the off position during the installation process. Failure to do this will cause the “check engine” light to be set. 2. Remove seat exposing the Electronic Control Unit (ECU) and battery. 3. Remove the right side coil cover by removing two allen screws and gently pulling. 4. Disconnect the 6 pin factory connector behind the ignition coils. (Fig 1) 5. Connect Fuelpak 6 pin connectors in-line with factory connectors. 6. Disconnect 3 pin factory connectors behind the ignition coils and connect Fuelpak 3 pin connectors in-line with factory connectors. 7. Route Fuelpak harness up to battery area and reinstall coil side cover. 8. Connect Fuelpak black wire to negative ground wire. (Fig 2) 9. Locate factory 2 pin connector with brown and black wires. Disconnect empty connector and attach Fuelpak red wire connector. 10. Connect Fuelpak 10 pin connector to Fuelpak harness. 11. You are now ready to set-up your Fuelpak. INSTALLATION INSTRUCTIONS FOR P/N 65001 READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION FUEL INJECTION MANAGEMENT SYSTEM ROADLINER / STRATOLINER NOTICE: Fuelpak is intended for racing or off-highway use only, and is not legal for sale or use in California on pollution-controlled vehicles. PLEASE NOTE: FUELPAK USE REQUIRES A HIGH PERFORMANCE AIR FILTER. HOW IT WORKS ENTERING VALUES 1. Remove Fuelpak clear case cover by removing all four screws, save hardware . 2. Turn on main power with key, but do not start engine. Fuelpak display should light up, if not, turn power off and verify the connectors are fully seated. 3. Refer to Fuelpak Setting Reference to locate the Setting Values specific to your bike and exhaust system. If you do not find your setting, visit fuelpakfi.com or call tech support at (562) 921-0071. 4. Starting with mode 1 selected, press the value (+) or the value (-) buttons to input the correct value as indicated in your Setting Value. After entering your first value, press the mode select button to move to mode 2 and enter the value. Continue until you have entered the value for each of the first 18 mode positions. Each time the value (+) is pressed, the value increases by one number. Each time the value (-) is pressed, the value decreases by one number. (Please refer to the “How It Works” section directly above if you have questions about this step. 5. As the next procedure, after you have entered in your values for the first 18 modes, press the mode select button to move to mode 19. Fully twist open the throttle and return to idle position to calibrate the Fuelpak to your bike. 6. By pressing the mode select button twice, move to mode 21 and verify that it reads “0″ with the throttle closed, “50″ at approximately half-throttle and “99″ when fully opened; if not, repeat step 5. Do not proceed to step 7 until mode 21 is verified.

Incoming search terms:

Yamaha V Star 1300 Fuel Injected INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Be sure the main switch is in the off position during the installation process. Failure to do this will cause the “check engine” light to be set. 2. Remove seat exposing the tool tray and battery. 3. Remove the (2) 12mm Hex head bolts securing rear of tank. Prop up the rear of the tank. 4. Locate and unplug the white 4-pin connector under left side of tank as shown in figure 1. 5. Route Fuelpak as shown in figure 2. Plug Fuelpak white connectors to the factory connectors unplugged in step 4. 6. Connect brown and green wires to the negative side of the battery. 7. Route Fuelpak long black wire under right side of tank and down to the horn as shown in figure 3. Disconnect the factory black / white wire from horn. Plug in Fuelpak long black wire to horn and then connect factory black / white wire to terminal on Fuelpak black wire. 8. Locate the throttle position sensor on the throttle body located on right side of the tank. As shown in figure 4, attach T-tap to yellow / black wire on throttle position sensor. Connect Fuelpak violet wire to T-tap. 9. Using supplied Velcro, mount Fuelpak next to tool tray as shown in figure 5. 10. Reinstall tank with (2) 12mm Hex head bolts removed in step 3. 11. You are now ready to set-up your Fuelpak 1. Remove Fuelpak clear case cover by removing all four screws, save hardware . 2. Turn on main power with key, but do not start engine. Fuelpak display should light up, if not, turn power off and verify the connectors are fully seated. 3. Refer to Fuelpak Setting Reference to locate the Setting Values specific to your bike and exhaust system. If you do not find your setting, visit fuelpakfi.com or call tech support at (562) 921-0071. 4. Starting with mode 1 selected, press the value (+) or the value (-) buttons to input the correct value as indicated in your Setting Value. After entering your first value, press the mode select button to move to mode 2 and enter the value. Continue until you have entered the value for each of the first 18 mode positions. Each time the value (+) is pressed, the value increases by one number. Each time the value (-) is pressed, the value decreases by one number. (Please refer to the “How It Works” section directly above if you have questions about this step. 5. As the next procedure, after you have entered in your values for the first 18 modes, press the mode select button to move to mode 19. Fully twist open the throttle and return to idle position to calibrate the Fuelpak to your bike. 6. By pressing the mode select button twice, move to mode 21 and verify that it reads “0″ with the throttle closed, “50″ at approximately half-throttle and “99″ when fully opened; if not, repeat step 5. Do not proceed to step 7 until mode 21 is verified. 7. Enter any other mode values as required for your application. 8. Turn off power. 9. Reinstall clear cover, tuck Fuelpak under seat area and reinstall seat. 10. You are now ready to ride

KAWASAKI VULCAN 1600 / NOMAD 1600 INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove seat and fuel tank. Consult service manual for proper removal of tank. 2. Remove left side cover and loosen the four bolts inside. Route the two 6-pin connectors between the side cover and frame as shown by the dotted line. Tighten the four bolts. (Fig 1) 3. Route 6-pin connectors under frame and up left side of engine. (Fig 2) 4. Locate the 6-pin connector next to the ignition coil. Disconnect and connect the Fuelpak 6-pin connectors in-line on the stock connector. (Fig 3) 5. Route single black wire to the front of engine and down to the horn. (Fig 4) 6. Disconnect the factory black/white wire from horn. Plug Fuelpak into horn and plug Fuelpak black/white wire to Fuelpak connector. Be sure Fuelpak connector cannot short to frame or radiator. 7. Route black and green wires to battery negative. 8. Attach Fuelpak to Fuelpak harness and mount in left side cover. (Fig 5a 49 State) (Fig 5b Caliornia Models) 9. Before reassembling the bike, make sure handlebar switch is in the engine off position and turn the key on. Fuelpak should light up. Sound the horn. If Fuelpak turns off when the horn is sounded, recheck the black wire connection on the horn and that it is connected to the correct wire from the factory harness. 10. Use supplied zip ties to hold Fuelpak wire harness away from engine. 11. Follow the service manual to reinstall the gas tank

Incoming search terms:

2008 Harley-Davidson TOURING INJECTION FUEL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2012

download
1. Remove seat, exposing factory computer (ECU). disconnect factory wiring by pressing lock and pushing lever back. 2. Remove ECU by pushing tab and sliding the ECU to the right as you lift. 3. Gently align the pins of the Fuelpak connector with the ECU and press the connector on the ECU. Be sure the single large pin is aligned with the single large socket before pressing Fuelpak connector into the ECU. Make sure all four tabs fully latch. (Fuelpak connector Patent Pending# 29 295831) 4. Connect factory wiring to Fuelpak connector and pull lever to locked location. Be sure that lock snaps into position. 5. Reinstall ECU. 6. Remove left side cover. 7. Slide Fuelpak down through opening leading to the area under the left side cover. 8. Attach Fuelpak to the fuse cover using supplied velcro.
HOW IT WORKS ENTERING VALUES 1. Remove Fuelpak clear case cover by removing all four screws, save hardware . 2. Turn on main power and handlebar switches, but do not start engine. Fuelpak display should light up, if not, turn power off and verify the connectors are fully seated. 3. Refer to Fuelpak Setting Reference to locate the Setting Values specific to your bike and exhaust system. If you do not find your setting, visit fuelpakfi.com or call tech support at (562) 921-0071. 4. Starting with mode 1 selected, press the value (+) or the value (-) buttons to input the correct value as indicated in your Setting Value. After entering your first value, press the mode select button to move to mode 2 and enter the value. Continue until you have entered the value for each of the first 18 mode positions. Each time the value (+) is pressed, the value increases by one number. Each time the value (-) is pressed, the value decreases by one number. (Please refer to the “How It Works” section directly above if you have questions about this step. 5. By pressing the mode select button 3-times, move to mode 21 and verify that it reads “0″ 6. Enter any other mode values as required for your application. 7. Turn power off, wait one second then turn power back on. Verify all modes then turn power off. 8. Reinstall Fuelpak clear cover then reinstall side cover

SUZUKI BOULEVARD M109R Fuel Injected Models INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 16-02-2012

download
1. Remove seat, right and left side covers, and fuel tank. 2. Remove airbox. We highly recommend you consult the factory service manual for proper removal of airbox. 3. Route wiring harness as shown in the picture. (Fig 1) 4. Unplug stock wiring harness from injectors and plug in the connectors from Fuelpak as shown. (Fig 2) 5. Unplug the TPS connector (grey) and attach T-tap connectors to the two outside wires. (Fig 3) 6. Route Fuelpak green wire to T-tap on the factory black wire with brown stripe. Routh the Fuelpak violet wire to T-tap on the factory pink wire with black stripe as shown (Fig 3) 7. Reattach the TPS connector. 8. Route red wire to the front of engine and down to the horn. (Fig 4) 9. Disconnect the two position connector from horn and snip connector in half so you have two one-wire connections. 10. Reattach factory grey wire to horn. Attach Fuelpak red wire to the other horn connection. Plug the factory horn orange wire to the male connection on the Fuelpak red wire. 11. Route black wire to battery negative connection as shown. (Fig 5) 12. Attach Fuelpak to Fuelpak harness and mount to bracket under the left side cover as shown. (Fig 6) 13. Before reassembling the bike, make sure handlebar switch is in the engine-not-running position and turn the key on. Fuelpak should light up. Sound the horn. If Fuelpak turns off when the horn is sounded, recheck the red wire connection on the horn and that it is connected to the orange wire from the factory harness. 14. Follow the service manual to reinstall the airbox and gas tank.

Incoming search terms:

SUZUKI GSX-R1300 / HAYABUSA Fuelpak Connectors INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 15-02-2012

download
Remove the main seat and passenger seat. 2. Use a prop to hold the tank up in the trunk area. 3. Disconnect the main wiring harness from each of the lower injectors. (Fig 1) 4. Lay the Fuelpak unit in the tail section and route the wire harness down the left side of the motorcycle toward the throttle bodies. 5. Plug the Fuelpak wiring harness in line of the stock wiring harness and injectors. (Fig 2) 6. Locate the throttle position sensor connector on the right hand side of the throttle body. 7. Install the Fuelpak wiring harness TPS connectors in line of the stock wiring harness. (Fig 3) 8. Attach ground wire to the negative side of the battery. 9. Install Fuelpak in the tail section using the supplied velcro. (Fig 4) 10. Bolt the fuel tank back into place. INSTALLATION INSTRUCTIONS FOR P/N 62009 READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION FUEL INJECTION

CL-1000 CONDOR CYCLE LOADER USER INSTRUCTION MANUAL

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
Confirm that the cradle is set in the optimized position setting (See RECOMMENDED CRADLE SETTINGS) for the entering tire and wheel. Adjustment of cradle is crucial for optimum retention. Optimum retention is achieved by trying different settings. ( REFER TO CAUTION PARAGRAPH BELOW ): If the optimum vertical support is achieved, the motorcycle will hold itself upright. If optimum retention is not achieved try different cradle settings. ( REFER TO CAUTION PARAGRAPH BELOW ). Once cradle is positioned, tighten the brakes using the eye bolts and place the Cycle Loader in front of the motorcycle. Push or drive the motorcycle, centered into unit, until the cradle of the Cycle Loader has fully engaged the wheel. Once the wheel is cradled, proceed to push further into the Cycle Loader until the wheel has engaged the front stop. If the optimum vertical support is achieved, the motorcycle will hold itself upright. As an extra precaution, an optional Velcro strap may be used to strap the cradled wheel to the front stop (Optional Velcro strap purchased separately). Always strap Velcro through the wheel and around the front stop below the upper front stop flange. Loosen the brakes and use two (2) tie-down straps to secure the motorcycle to the two front eyebolts of the Cycle Loader. Hook wench to Ω” ‘U’ hook in front of Cycle Loader. Use the wench to pull the Cycle Loader with motorcycle up the flat bed. Once the motorcycle is all the way on the flat bed, the bike should be secured to the flat bed itself. For more information on use, refer to www.condor- lift.com. RECOMMEDED CRADLE SETTINGS: The Condor® Cycle Loader is designed so that for every tire/wheel size within the ranges specified a minimum of 2 cradle settings is suitable. **The optimum cradle setting for a specific tire would be, the setting that allows the cradle to tilt flush with the unit/ or º” below the opening in the main unit where the cradle sits, without touching.** The 2nd optimum setting would be the setting forward from the optimum setting away from the entry direction. If less retention is desired at any time due to too much retention or sticking, the cradle may be moved away from the entry direction one notch. RACING APPLICATIONS: For bikes with GP or low durometer front tires compounds, use the 5th cradle setting from the entry directions. CAUTION: Always make sure that all fasteners are tight and all pins are in place prior to use. Understand the limitations of this product and do not exceed these limitations. Always make sure that the unit’s cradle settings are optimum for the tire size of the motorcycle before use. For bikes with very low fenders and or cowlings, a custom cradle may be purchased fitted to specific tire sizes, so as not to make contact. For standard sport bike front wheel combinations, the 1, 2, 3, front settings may be suitable. If instructions are not clear, additional information is available at www.condor-lift. com or call 1-800-461-1344. Technical Components Development & Design is not responsible for any damage incurred by exceeding this product’s limitations in structure and/or functionality.

Incoming search terms:

2008 KTM Model Engine Oil Recommendation Chart

0

Filed Under (KTM) by admin on 24-11-2010

download
2008 Model Type Recommended Engine Oil Type Quantity SPORTMINICYCLES AC 50 SX MINI Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L SPORTMINICYCLES LC 50 SX JUNIOR Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 50 SX Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 65 SX Motorex Top Speed 4T 15W50 0.5L SX 2 STROKE 85 SX Motorex Top Speed 4T 15W50 0.5 L 105 SX Motorex Top Speed 4T 15W50 0.5 L 125 SX Motorex Top Speed 4T 15W50 0.7 L 144 SX Motorex Top Speed 4T 15W50 0.7 L 250 SX Motorex Top Speed 4T 15W50 0.7 L SX 4 STROKE 250 SX-F Motorex Power Synt 4T 10W50 1.1 L 450 SX-F Motorex Power Synt 4T 10W50 1.35 L 505 SX-F Motorex Power Synt 4T 10W50 1.35 L CROSS COUNTRY 2 STROKE 65 XC Motorex Top Speed 4T 15W50 0.5L 85 XC Motorex Top Speed 4T 15W50 0.5L 105 XC Motorex Top Speed 4T 15W50 0.5 L 200 XC Motorex Top Speed 4T 15W50 0.7 L
200 XC-W Motorex Top Speed 4T 15W50 0.7 L 250 XC Motorex Top Speed 4T 15W50 0.7 L 250 XC-W (e) Motorex Top Speed 4T 15W50 0.7 L 300 XC Motorex Top Speed 4T 15W50 0.7 L 300 XC-W (e) Motorex Top Speed 4T 15W50 0.7 L CROSS COUNTRY 4 STROKE 250 XC-F Motorex Power Synt 4T 10W50 1.1 L 250 XC-F-W Motorex Power Synt 4T 10W50 1.1 L 450 XC-F Motorex Power Synt 4T 10W50 1.35 L 450 XC-W (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L 505 XC-F Motorex Power Synt 4T 10W50 1.35 L 530 XC-W (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L ENDURO RACING 450 EXC (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L 530 EXC (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L SUPERMOTO LC4 690 Supermoto Motorex Power Synt 4T 10W60 Approx. 2.0 L SPORT ATV 450 XC Motorex Power Synt 4T 10W50 2.0 L 525 XC Motorex Power Synt 4T 10W50 2.0 L LC8 950 Super Enduro (R) Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure Orange Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure Black Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure S Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Super Duke Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Super Duke R Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L

Incoming search terms:

2006 Model Engine Oil Recommendation Chart

0

Filed Under (KTM) by admin on 26-11-2010

download
2006 Model Type Recommended Engine Oil Type Quantity SPORTMINICYCLES AC 50 MINI ADVENTURE Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 50 SENIOR ADVENTURE Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L SPORTMINICYCLES LC 50 SX JUNIOR Motorex Top Speed 4T 15W50 0.15-0.2 L 50 SX Motorex Top Speed 4T 15W50 0.15-0.2 L 65 SX Motorex Top Speed 4T 15W50 0.3L SX 2 STROKE 85 SX Motorex Top Speed 4T 15W50 0.5 L 105 SX Motorex Top Speed 4T 15W50 0.5 L 125 SX Motorex Top Speed 4T 15W50 0.7 L 250 SX Motorex Top Speed 4T 15W50 0.7 L SX 4 STROKE 250 SX-F Motorex Power Synt 4T 10W50 1.1 L 450 SX Motorex Power Synt 4T 10W50 1.25 L 525 SX Motorex Power Synt 4T 10W50 1.25 L CROSS COUNTRY 2 STROKE 200 XC Motorex Top Speed 4T 15W50 0.7 L 200 XC-W Motorex Top Speed 4T 15W50 0.7 L 250 XC Motorex Top Speed 4T 15W50 0.7 L 250 XC-W Motorex Top Speed 4T 15W50 0.7 L 300 XC Motorex Top Speed 4T 15W50 0.7 L 300 XC-W Motorex Top Speed 4T 15W50 0.7 L CROSS COUNTRY 4 STROKE 450 XC Motorex Power Synt 4T 10W50 1.25 L 525 XC Motorex Power Synt 4T 10W50 1.25 L ENDURO RACING 400 EXC Motorex Power Synt 4T 10W50 1.25 L 450 EXC Motorex Power Synt 4T 10W50 1.25 L 525 EXC Motorex Power Synt 4T 10W50 1.25 L ADVENTURE LC8 950 Adventure orange Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 950 Adventure black Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 950 Adventure S Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L SUPERMOTO RACING 450 SMR Motorex Power Synt 4T 10W50 1.25 L 560 SMR Motorex Power Synt 4T 10W50 1.25 L SUPERMOTO LC4 625 SMC Motorex Power Synt 4T 10W50 Approx. 2.1 SUPERMOTO LC8 950 Supermoto orange Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 950 Supermoto black Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L

Incoming search terms:

Incoming search terms: