gas gauge for 1996 flhr

You search Auto repair manual PDF gas gauge for 1996 flhr, if there are search results will appear below. If search results do not exist, please search by others keyword.



  gas gauge for 1996 flhr Direct Download speed 5282 Kb/s

  gas gauge for 1996 flhr Full Version speed 6162 Kb/s



HARLEY DAVIDSON LED FUEL GAUGE KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Removing the Analog Fuel Gauge NOTE The fuel gauge wires are routed through a tube in the fuel tank, and are secured by a clip at the bottom of the tank and, on some models, a clamp on the frame. Open the clip and clamp as needed, and be sure there is enough slack in the wires to be able to lift out the gauge. 1. At the bottom left side of the fuel tank, bend back the flexible clip slightly to free the fuel gauge conduit. Open the harness clamp on the frame if necessary to free the conduit. Gently pull on the conduit to draw the Multilock connector [117] out of the tunnel. 2. See Figure 2. Depress the pin on the socket terminal side of the connector, and pull apart the pin and socket halves. 3. See Appendix B in an appropriate Service Manual. Use a pick (Snap-On TT600-3 or equivalent) to remove the terminals or clip off the wires. Remove and discard the fuel gauge. 4. For Carbureted Models: See Figure 2. Remove the fuel gauge by firmly grasping and carefully pulling up (do NOT twist) on the gauge just far enough to free it from the fuel tank. Disconnect the two sending unit connectors. Feed the conduit and two wires up through the tube while removing the gauge. Remove and discard the fuel gauge. For Fuel-Injected Models: See Figure 2. Remove the fuel gauge by firmly grasping and carefully pulling up (do NOT twist) on the gauge to free it from the fuel tank. Feed the conduit and three wires up through the tube while removing the gauge. Remove and discard the fuel gauge. 5. Remove and discard the rubber gasket. INSTALLATION For Kit Numbers 75084-04B or 75237-03B 1. See Figure 2. Assemble the new gasket (3) to the LED fuel gauge (1) from the kit. Install the gasket so the flat side contacts the edge of the gauge. 2. See Figure 1. Use three of the Phillips-head screws and washers from the kit to connect the wires as follows: Fasten the Orange wire (1) ring terminal to the gauge connection marked “12V and “O” with a screw and washer. Fasten the Black wire (2) ring terminal to the connection marked “GND” and “BK” with a screw and washer. Fasten the Yellow/White wire (3) ring terminal to the connection marked “Y/W” with a screw and washer. 3. See Figure 2. While carefully lowering the fuel gauge, feed the wire harness (2) down into the drain tube until the three short (Orange, Black, Yellow/White) wires exit the hole at the bottom of the fuel tank. Gently pull the wires to remove slack while installing the gauge to the fuel tank. Do not twist the gauge during installation. Hold the gauge firmly and press down until it snaps into place

Incoming search terms:

HARLEY DAVIDSON FLUSH-MOUNT LED FUEL GAUGE AND GAS CAP KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Remove stock gas cap from fuel tank. 2. Clean and wipe inside surface of fuel tank filler cup, O-ring seal surface, and trim ring adhesive surface with a mixture of equal parts of isopropyl alcohol and distilled water. 3. See Figure 1. Install gas cap into fuel tank. is00407 Figure 1. Screw in Gas Cap is00466 Figure 2. Note Position of Arrow on Trim Ring 4. Push down on gas cap and rotate clockwise one-eighth of a turn to lock. To unlock, push down on gas cap and rotate counterclockwise one-eighth of a turn. 5. See Figure 2. Before removing adhesive backing, note position of arrow on inside diameter of chrome trim ring. NOTE As you rotate trim ring, you will see gaps between trim ring and fuel tank. Rotate trim ring to position that best eliminates gaps between fuel tank and trim ring. Rotation of trim ring should be minimal. 6. See Figure 3. With the arrow pointing toward front of motorcycle, rotate chrome trim ring slightly to determine best position of bottom chrome trim ring to contour of the fuel tank 7. See Figure 4. Mark position of chrome trim ring with masking tape or grease pencil. 8. Carefully cut masking tape with a hobby knife making sure not to scratch chrome trim ring or paint surface on fuel tank. 9. Peel off adhesive backing from chrome trim ring. 10. Using gas cap to center and masking tape (or grease pencil mark) to align, press chrome trim ring firmly into position for about ten seconds. 11. Peel off masking tape (or remove grease pencil mark) from chrome trim ring and fuel tank. 2 1 is00414a 1. Masking tape 2. Cut masking tape Figure 4. Align Trim Ring and Press into Place NOTE Allow adhesive trim ring to cure for about 5-7 minutes before you continue with kit installation. Install Flush-Mount LED Fuel Gauge 1. Remove the seat following the instructions in the service manual. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove stock fuel gauge. Refer to service manual for instructions. 4. Insert wires down tube of fuel tank from LED fuel gauge. 5. See Figure 5 and Figure 6. Insert LED fuel gauge in the fuel tank cup

Incoming search terms:

ATK 50MX INSTALLATION AND ADJUSTMENT TIPS

0

Filed Under (Atk) by admin on 01-11-2010

download
PRELOAD ADJUSTMENT— On some Works shocks a threaded preload is standard. This allows the adjustment of the ride height of the motorcycle. The preload is changed by turning a threaded nut down towards the spring (higher ride height) or up away from the spring (lower ride height). The nut is a right-hand thread. CHECKING RIDE HEIGHT— 1. With the bike unloaded on the side stand and the shock fully extended, have an assistant measure from a point at the axle (center point) to a point on the frame, fender or bodywork directly above it. Record this measurement. 2. With the bike off the stand and the rider in the seat, bounce on the suspension and let the bike settle. Have the assistant measure from the same two points. Subtract the second measurement from the first. HM CRX50 / BAJA & ATK 50MX INSTALLATION AND ADJUSTMENT TIPS Continued on next page. #HM50 – 5/27/99 #HM50 – 5/27/99 To Front Valve Mounting channel Spacer Flange Shock eye Top View of Shock Mount Fig. 1 Top view of upper shock mount. The flange on the shock bushing must face toward the spacer. The valve should point toward the front of the bike Fig. 1 Top view of upper shock mount. The flange on the shock bushing must face toward the spacer. The valve should point toward the front of the bike 3. The amount of settle, or “sag” is a function of the wheel travel. It should only be between 1/4 and 1/3 of the total travel. 4. If the difference is less than the minimum, reduce the spring preload. Measure the distance again starting with Step 2. Adjust again if necessary. 5. If the difference is more than the maximum, increase the spring preload. Measure the distance again starting with Step 2. Adjust again if necessary. Note: If the ride height is too low, the shock will bottom unnecessarily, resulting in a harsh ride. If the ride height is too high, the shock will “top out” too easily when rebounding from a bump or under hard deceleration. NITROGEN PRESSURES IN EMULSION SHOCKS CAUTION: The pressure in these shocks cannot successfully be checked. Concerns with the gauge volume and the gas volume in the shock body create a situation where you cannot accurately determine what pressure was in the shock. In addition when the pressure is lowered (i.e. checking the pressure) the gas and some of the shock oil escapes into the gauge. It is possible to lose a large percentage of the shock oil by depressing the core of a charged shock to the atmosphere. Please note that in order to check the pressure, some of the gas must escape and fill the gauge assembly. The volume of the gas pocket is about half the size of your thumb, so a very small volume change results in a large pressure drop. Because the gauges’ volumes vary, it is not possible to deduce the actual pressure in the shock prior to attaching the gauge. Therefore it is imperative that any attempt to check pressure be accompanied by the capability of refilling the shock. In other words: If you don’t have a nitrogen source handy, don’t check the pressure! PRESSURIZING EMULSION SHOCKS The pressure setting for Works gas shocks is 250 p.s.i. of dry nitrogen. To pressurize a shock with some residual pressure in it, bring the gauge manifold up to 250 p.s.i. and depress the core with the T-handle. This will either equalize the pressure or refill the shock without transferring oil from the shock into the gauge assembly. The best gauges for this purpose screw on to the valve and incorporate a T-handled core depressor to isolate the shock from the gauge. This allows a leak-free separation once the desired pressure is reached. For simplified operation, an extra valve is provided for the filling apparatus, allowing pressure adjustment with the gauge in place. Works offers a suitable gauge and filling manifold. Most motorcycle shops that deal with dirt bikes can pressurize the shock

Incoming search terms:

2009 GAS GAS TXT PRO TECHNICAL SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Gas Gas) by admin on 28-11-2010

download
ENGINE 2 stroke, single cylinder, direct reed valve crankcase induction. Liquid cooled. 125 cc. engine Cylinder size 124,8 cc. Bore and stroke 54 x 54.5 mm. 200 cc. engine Cylinder size 175,3 cc. Bore and stroke 64 x 54,5 mm. 250 cc. engine Cylinder size 247,7 cc. Bore and stroke 72,5 x 60 mm. 280 cc. engine Cylinder size 272,2 cc. Bore and stroke 76 x 60 mm. 300 cc. engine Cylinder size 294,1 cc. Bore and stroke 79 x 60 mm. Carburettor, diameter of the diffusor 26 Lubrication system Mixture (50:1)(2%) Ignition system Digital magnetic flywheel CDI TRANSMISSION Transmission type 6 gears, Four / Six system by GAS GAS* (Patented). Clutch type Hydraulic command, 1/3 discs, variable progressive with diaphragm system by GAS GAS* (Patented). Driving system By chain Gear ratio 1st. 2,996 (35x27x28/16x24x23) 2nd. 2,571 (36/14) 3th. 2,187 (35/16) 4st. 2,112 (36x23x24/14x28x24) 5st. 1,125 (27/24) 6th. 0,821 (23/28)
-11- Primary reduction ratio 2,777 (75/27) Final reduction ratio 3,818 (42/11) Overall drive ratio 8,704 (6th. gear) Transmission oil Capacity 550 cc. Type 10W40 API SF o SG. FRAME Type Tubular profile made with Cr-Mo. Tyres Front 2,75 x 21″ Trial Rear 4,00 x 18″ Trial tubeless. Suspension Front Adjustable tele-hydraulic fork ø 40 mm. (125 / 200). Adjustable tele-hydraulic fork ø 40 mm with aluminium bars (250 / 280 / 300) Rear Variable progressive system with mono-shock multiadjustable. Suspension stroke Front 177 mm. Rear 164 mm. Front fork oil SAE 5. Front fork oil level ø 40 mm.(125 / 200) 180 mm. air chamber steel bar ø 40 mm. (250 / 280 / 300) 160 mm. air chamber aluminium bar BRAKES Type Disc brake. Disc diameter Front ø185 mm. 4 piston calipers. Rear ø150 mm. 2 piston calipers. DIMENSIONS Overall height 1180 mm. Overall width 820 mm. Seat height 650 mm. Ground clearance 315 mm. Wheelbase 1330 mm. Fuel tank capacity 3,1 liters.

Incoming search terms:

1998 BMW R1100RT LCD Temperature Gauge Scale Calibration LCD Fuel Gauge Calibration Fuel Sender Testing and Cleaning

0

Filed Under (BMW) by admin on 26-10-2010

download
Oil Temperature and Gauge 2.1. Introduction My 1998 BMW R1100RT came with an LCD temperature gauge that shows horizontal black bars in a vertical motif, to indicate temperature. This is difficult to interpret at speed (how many bars are exposed?) and does not actually tell me what the oil temperature is. 2.2. Normal Operation The bike seems to run at 5 or six bars under normal conditions. It appears that the oil thermostat for the cooler is set to ’5 bars’. 2.3. Over Heating The LCD panel indicates that 8 bars is the maximum normal operating temperature. It would be useful to know what the actual temperature is. Modern oils have a normal operating temperature of approximately 110 degrees Celsius and will not show any serious degradationii at this temperature. The maximum sustained operating temperature (at the bearing surface) is approximately 130 degrees Celsius for any oil formulated in the past 5 years and some high performance synthetics will not appreciably degrade even at this temperature. However, the degradation curve is a polynomial and degradation will increase rapidly with increasing temperature. According to the oil’s formulation (pure synthetics will show the least increase with temperature), by approximately 160 degrees Celsius (or about 300 degrees Fahrenheit), oil degradation can be up to 10 times faster then at 110 Deg. C. 2.4. Scale To fix the ‘number of bars’ problem, I determined that an overlay with numbers would be the best idea. 2.4.1. Addendum The number scale became too much to maintain. Rather than this, I cut a mm or so wide stripe out of the self sticking stripping meant for the side of a car. Using a red material, I put it through the middle of the fifth bar of both the temperature and fuel display. The stripe is slightly smaller than the thickness of the bar. This allows me to tell when I am at normal operating temperature and when approximately half a tank is used

Incoming search terms:

HARLEY DAVIDSON LOCKING FUEL FILLER CAP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION 1. Prior to installing the gas cap on the vehicle, insert the key into the lock. Firmly grasp the chrome top of the fuel cap and turn the key until it stops. On right hand threaded fuel caps, turn the key counter-clockwise until it stops. On left hand threaded fuel caps, turn the key clockwise until it stops. This assures an unlocked position for the gas cap. Allow the key to return to the neutral position. 2. Remove the key and install the fuel cap on the vehicle. is00770 Figure 1. Right Hand Threaded Fuel Cap Installation NOTE When installing the fuel cap, rotate the cap one full turn past the audible click. This automatically positions gas cap to lock position. A properly locked/installed gas cap will rotate freely in both directions. Failure to do so will give an incorrect assumption that the fuel cap does not work properly. REMOVAL On right hand threaded fuel caps, insert key, and while holding the gas cap in place with hand, turn key counterclockwise until it stops, return key to original position. Gas cap must rotate 270 degrees counter-clockwise before mechanism engages to allow gas cap removal. Continue to rotate counterclockwise to fully remove gas cap. On left hand threaded fuel caps, insert key and while holding the gas cap in place with hand, turn key clockwise until it stops, return key to original position. Gas cap must rotate 270 degrees clockwise before mechanism engages to allow gas cap removal. Continue to rotate clockwise to fully remove gas cap. REPLACEMENT KEYS Record the 4 digit key number stamped on the back of the key opposite the Harley-Davidson logo, in the area provided below. If a replacement key is needed, see your Harley-Davidson Dealer with the 4 digit number to order a replacement

Incoming search terms:

FLEXIBLE GAS PIPING DESIGN GUIDE and INSTALLATION INSTRUCTIONS

0

Filed Under (S&S) by admin on 29-10-2010

download
Definitions: Grounding : The process of making an electrical connection to the general mass of the earth. This is most often accomplished with ground rods, ground mats or some other grounding system. Low resistance grounding is critical to the operation of lightning protection techniques. Bonding : The process of making an electrical connection between the grounding electrode and any equipment, appliance, or metal conductor: pipes, plumbing, flues, etc. Equipment bonding serves to protect people and equipment in the event of an electrical fault. Equipotential Bonding : The process of making an electrical connection between the grounding electrode and any metal conductor: pipes, plumbing, flues, etc., which may be exposed to a lightning strike and can be a conductive path for lightning energy towards or away from the grounding electrode. 2. The National Fuel Gas Code NFPA 54/ANSI Z223 states, “Each above ground portion of a gas piping system upstream from the equipment shutoff valve shall be electrically continuous and bonded to any grounding electrode, as defined by NFPA 70, National Electrical Code ( ANSI/NFPA 70 1999 Edition.) 3. The TracPipe® gas piping system shall be bonded in accordance with the National Fuel Gas Code, NFPA 54/ANSI Z223. The piping system is not to be used as a grounding conductor or electrode for an electrical system. 4. For bonding of the TracPipe® system, a bonding clamp must be attached to the brass AutoFlare®fitting adapter (adjacent to the pipe thread area – see Figure 4-21) or to a black pipe component (pipe or fitting) located in the same electrically continuous gas piping system as the AutoFlare®fitting. The corrugated stain- less steel portion of the gas piping system SHALL NOT be used as the bonding attachment point under any circumstances. Bonding electrode conductor sizing shall be in accordance with Article 250 (Table 250-66) of ANSI/NFPA 70. The bonding is a requirement of the National Electrical Code

Oil Pressure Gauge Set Installation

0

Filed Under (Tips and Review) by admin on 27-11-2010

download
7. See Figure 3-4 . Assemble banjo bolt (3), washer (4), OIL PRESSURE GAUGE (1) banjo fitting and second washer onto adapter and tighten snugly. 8. Temporarily secure oil pressure gauge and hose to motorcycle frame with cable straps. Make sure gauge and hose assembly do not interfere with normal operation of the vehicle. Start engine and ride motorcycle at least 20 miles (32 km) at or above 50 mph (80 km/h) to allow engine to reach operating temperature. a. At 2500 RPM, oil pressure will vary from 10-17 psi (69-117 kN/m2). b. At idle speed (950-1050 RPM), oil pressure will vary from 7-12 psi (48-83 kN/m2). NOTE For an accurate reading, engine oil should be at normal operating temperature: 230°F (110°C). 9. Stop engine. Remove OIL PRESSURE GAUGE assembly from oil pressure indicator lamp switch mounting hole in crankcase. Cut cable straps that you installed in step 8. above, and remove banjo bolt, gauge assembly, washers and adapter from vehicle. 10. See Figure 3-2 . Coat threads of oil pressure switch (2) with LOCTITE 565 HIGH PERFORMANCE PIPE SEALANT with TEFLON. Reinstall oil pressure switch. Using OIL PRESSURE SENDING UNIT WRENCH, tighten switch snugly. DO NOT OVERTIGHTEN. 11. Plug in connector [120] (3) by pushing elbow connector straight up onto stud on oil pressure switch. 12. Install voltage regulator caddy and attach DC output connector and neutral switch wiring harness to caddy. See 7.28 MAIN WIRING HARNESS . NOTE If an appreciable amount of oil leaked out when oil pressure switch was removed, it will have to be replaced with fresh oil. 13. Check oil level in oil tank. See 1.5 ENGINE OIL AND FILTER . Top off oil level if necessary. 14. Start engine and test oil pressure switch for proper operation. Check oil pressure switch for leaks.

Incoming search terms:

KTM SX50/ SX50R MOUNTING INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 02-02-2012

download
top out” too easily and fail to allow enough travel for appropriate rebound from bumps. If the ride height is too low, the shock can bottom too easily, resulting in a harsh ride. The spring rates are set up for the full amount of travel. If the preload is too little, the combined rate is not enough to resist bottoming. Generally speaking, the vehicle should settle 1/4 to 1/3 of its wheel travel with the rider on board for off road use. The proper way to measure the ride height: 1. Support the vehicle on a frame stand or center stand with the rear wheel clear of the ground. 2. Have an assistant measure and record the vertical distance between the rear axle and a point directly above it (seat, fender, frame, muffler, etc.). 3. Take the motorcycle off the stand and sit on it in a normal riding posture, with one foot on the peg and the motorcycle balanced so as to have minimal weight on your other foot. 4. Have the assistant carefully measure from the same two points. Subtract the second measurement from the first. The difference is the amount of settling or “sag.” NITROGEN PRESSURES CAUTION: The pressure in these shocks cannot successfully be checked. Concerns with the gauge volume and the gas volume in the shock body create a situation where you cannot accurately determine what pressure was in the shock. In addition, the gas is in a column on top of the oil, and when the pressure is lowered (i.e. checking the pressure) the gas will emulsify into the oil. This will cause the gas and some of the shock oil to escape into the gauge. It is possible to lose a large percentage of the shock oil by depressing the core of a charged shock to the atmosphere. Please note that in order to check the pressure, some of the gas must escape and fill the gauge assembly. The volume of the gas pocket is about the size of your thumb, so a very small volume change results in a large pressure drop. Because the gauges’ volumes vary, it is not possible to deduce the actual pressure in the shock prior to attaching the gauge. Therefore it is imperative that any attempt to check pressure be accompanied by the capability of refilling the shock. In other words: If you don’t have a nitrogen source handy, don’t check the pressure

GAS GAS TXT BOY ENGLISH USER MANUAL

0

Filed Under (Gas Gas) by admin on 27-11-2010

download
Quick Guide to Maintenance Coolant liquid Coolant liquid -30ºC Crankcase oil (10w40) 500 cc. Electrode separation 0.6 mm. Forks suspension oil SAE 5 (Summer) SAE 2.5 (Winter) Fork suspension oil quantity200 cm3 Shock absorber spring length96 mm Front wheel pressure Standard 0.400 bar Competition 0.370 bar Rear wheel pressure Standard 0.350 bar Competition 0.300 bar -9- 1 Fuel – Petrol/oil mixture The motorcycle is fitted with a two-stroke internal combustion engine. This type of engine requires a mixture of petrol and oil. To ensure the correct working of the engine, the following are recommended: – Use high quality petrol, with an octane rating equal to or above 90 (RON + MON)/2 or 98 (RON). – Use 2T synthetic oil. Warning: – If the recommended oil is not available, use semi-synthetic oil. – Do not mix different oil-types. Mixture ratio: oil, 1.5% of petrol volume (50 parts petrol to every 0.75 part oil). Note: we recommend first preparing the mixture in a suitable container and then filling the fuel tank. Fuel tank This has a rapid access cap A and a vent hose B to allow gases produced in the tank to escape. – To open the cap, lift the clip in the direction shown by the arrow and turn to the left. Warning! Regularly check the cap seal and vent hose to ensure they are leak proof. Risk of spillage. -10- 3 2 Reserve Open Closed Fuel tap This has three positions: open, closed and reserve. The diagrams below show the position of tap A for each case. A Gear shift The motorcycle has a two- speed gearbox, which may be selected manually when the motorcycle is stationary, by moving the lever A in a horizontal direction, as shown by the arrow. Note: Select the gear according to the characteristics of the track

Incoming search terms: