gas leak on carb kawasaki kz750

You search Auto repair manual PDF gas leak on carb kawasaki kz750, if there are search results will appear below. If search results do not exist, please search by others keyword.



  gas leak on carb kawasaki kz750 Direct Download speed 5282 Kb/s

  gas leak on carb kawasaki kz750 Full Version speed 6162 Kb/s



KAWASAKI 1500 CARB THUNDER Air Filter Kit Installation And removal Instruction

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove Seat 10mm KAW 1500 CARB ADPTOR QTY PARTS LIST 1 1500 CARB ADAPTOR 1 3″ PIECE OF HOSE 1 DOUBLE BARB 1 L-BARB 1 3/8″ RED PLUG 1 ¼” BLACK VACCUM PLUG 1 M6-1 NYLON INSERT LOCK NUT 3 M6-1 X 16 FLAT SOCKET HD CAP SCREW 1 170 MJ 1 INSTRUCTIONS 2) Remove Dash Plaque 8mm bottom Bolt only 3) Lift from bottom then Remove speedo cable 4) Disconnect Electric Plugs 5) Remove 12mm bolts holding tank 6) Turn petcock OFF – Pinch off fuel line. 7) Disconnect the electric Plug under speedo opening 8) Lift Tank at Rear – Disconnect two Vent Lines; Fuel gage Vent will Pull up – Remove. 9) Remove Chrome Air Cover. 10) Left side Remove two screws – 10mm bolt in side Air box. Pull hoses off Remove 1″ hose going to cross over Tube. 11) Remove two 8mm bolts on Bracket – Remove Bracket 12) Remove Screw on Top of air Box Snorkel 13) Remove both side covers 14) Remove air Backing plate right side (Crank Case Breather hose that connects to stock air box will connect to new) 15) Remove Bracket that holds Carb and holds Backing Plate 16) Take idle adjustable Knob loose – let hang loose 17) Take Choke Knob out of holding Bracket 18) Hose that went to cross over tube MAY BE PLUGGED OR VENTED your Choice (Fresh air unit) ** 98′S or any models with carb warmer should disconnect carb warmer by pinching off line on each side of connector that plugs into carb on bottom. Small bracket with one screw directly on the bottom of carb. 19) Loosen Clamp that holds Carb to intake Manifold, Carb will hang loose 20) Remove intake Manifold 5mm Allen- Remove crossover tube. 21) (- BE CAREFULL-) LINE IT UP RIGHT- Replace intake Manifold (YOU MAY TO SEAL THIS WITH A SEALER LIKE PERMATEX) ( BE SUPER CAREFUL TO KEEP INTAKE COVERED DURING EACH STEP. SCREWS CAN FALL ONTO INTAKE) 22) Drain Float Bowl 3mm allen – very bottom of carb 23) Remove Float Bowl 4 screws (#2 Phillips) let hang down 24) Remove main jet, if Emulsion tube comes out use 8mm and Flat tip to separate jet from Emulsion tube. 25) Install with new jet 26) CAREFULLY Reinstall Float Bowl Cover 27) If installing Needle Remove Top Cover of Carb, Carefully pull the slide out. ( BE CAREFUL WITH DIAPHRAM) Remove Spring + Needle Install new Needle (WE RECOMMEND THE 3RD CLIP FROM TOP WITH TWO WASHERS ON TOP. REINSTALL 28) Be sure to reseat diaphragm – BE CAREFUL Reinstall Cover. 29) Install Carb to Intake – reconnect carb warmer if applicable 30) Reattach idle adjustment 31) Reattach Choke 32) Reattach Bracket in front of Carb- 33) Take Center bolt mount Rubber Gromlet from Stock Air box Plate install in to new Air box Adapter use stock Bolt, Attach to Bracke

Incoming search terms:

Kawasaki KZ750 Twin Carburetor Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The first Kawasaki KZ750 twin was built in 1975 and sold as a 1976 model as a KZ750B1. For the first four years of production (1976-79), the KZ750B1 through B4 shared identical Mikuni BS38 carburetor assemblies. These assemblies are probably the heaviest twin-carb assemblies ever built and have a couple unique features. The biggest oddity is that the Kawasaki version of the BS38 uses a system where both the pilot jet and main jet are screwed into the float bowl. A good bowl gasket is critical because gas is drawn from the jets into the internal passages that lead to the venturi via channels beneath the gasket inside the float chamber. The pilot jets used are standard BS series fare in that they are Mikuni BS30/96 type but the main jets are unique to Kawasaki BS38 carburetor assemblies. They look like very small air jets and are frequently stripped as they require the correct sized small screwdriver to remove

Incoming search terms:

HW Prowler Carburetor Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
1. Remove both seats and the plastic seat pans under the seats. 2. Remove the engine cover 3. Remove the air-box by removing the cross-bar support that runs under the air-box to the framing on each side by the seat framing and disconnect the air box from the carburetor and from the plastic intake in the rear. 4. Disconnect the engine breather hose from the bottom of the air box 5. Set the air-box to the side 6. Disconnect the plug going to the stock carburetor, this is the electronic choke. Wrap the end left on the vehicle with electrical tape. 7. Cut the fuel line just above the fitting on the passenger side of the carb 8. Remove the side cover off the drivers side of the carb where the throttle cable goes in, see fig. #1 9. Pull the throttle cable out and then remove the throttle cable end from the throttle plate See Fig. #2 10. Loosen the clamp on the rear of the carb holding the carb on 11. Pull the carb out of the intake boot 12. Set OE carb to the side. 13. Push the new Carb into the intake boot making sure the carb is perfectly vertical and then tighten the clamp back up. The new carb is slightly larger than the stock one so some additional pressure will be needed to get it in. 14. Route all the breather lines connected to the carb down under the carb. 15. Connect the throttle cable onto the new carb but putting the cable end in the bottom hole of the throttle plate on the passenger side of the carb allowing the cable to ride in the slot in the plate and then turn the throttle plate clock wise allowing the threaded end of the cable to fit into the lower round hole of the throttle cable connection plate. See Fig. #3 16. Make sure you have a nut on each side of the plate turn the nut on the outside of the plate to take up the slack in the throttle cable then tighten the nut on the inside of the plate. See Fig. #3 17. Push the fuel line onto the fuel inlet on the passenger side of the carb and install the supplied clamp to hold it on. The fuel line will be a little hard to push on. 18. DO NOT ATTEMPT TO INSTALL THE CHOKE CABLE PARTS SUPPLIED IN THE KIT UNTIL AFTER THE CHOKE CABLE ITSELF IS INSTALLED AND READY TO SCREW INTO THE CARBUETOR. 19. To install the supplied choke cable, drill a 3/8″ hole in the dash on the left side of the steering wheel in a location convenient to your left hand. 20. Remove the plastic nut from the bottom of the choke handle on the choke cable. 21. Push the choke cable thru the hole you drilled and then slide the nut over the cable to the inside of the dash and reinstall back on the back of the choke mechanism. Some dash screws maybe needed to be removed to accomplish this

Incoming search terms:

2009 GAS GAS TXT PRO TECHNICAL SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Gas Gas) by admin on 28-11-2010

download
ENGINE 2 stroke, single cylinder, direct reed valve crankcase induction. Liquid cooled. 125 cc. engine Cylinder size 124,8 cc. Bore and stroke 54 x 54.5 mm. 200 cc. engine Cylinder size 175,3 cc. Bore and stroke 64 x 54,5 mm. 250 cc. engine Cylinder size 247,7 cc. Bore and stroke 72,5 x 60 mm. 280 cc. engine Cylinder size 272,2 cc. Bore and stroke 76 x 60 mm. 300 cc. engine Cylinder size 294,1 cc. Bore and stroke 79 x 60 mm. Carburettor, diameter of the diffusor 26 Lubrication system Mixture (50:1)(2%) Ignition system Digital magnetic flywheel CDI TRANSMISSION Transmission type 6 gears, Four / Six system by GAS GAS* (Patented). Clutch type Hydraulic command, 1/3 discs, variable progressive with diaphragm system by GAS GAS* (Patented). Driving system By chain Gear ratio 1st. 2,996 (35x27x28/16x24x23) 2nd. 2,571 (36/14) 3th. 2,187 (35/16) 4st. 2,112 (36x23x24/14x28x24) 5st. 1,125 (27/24) 6th. 0,821 (23/28)
-11- Primary reduction ratio 2,777 (75/27) Final reduction ratio 3,818 (42/11) Overall drive ratio 8,704 (6th. gear) Transmission oil Capacity 550 cc. Type 10W40 API SF o SG. FRAME Type Tubular profile made with Cr-Mo. Tyres Front 2,75 x 21″ Trial Rear 4,00 x 18″ Trial tubeless. Suspension Front Adjustable tele-hydraulic fork ø 40 mm. (125 / 200). Adjustable tele-hydraulic fork ø 40 mm with aluminium bars (250 / 280 / 300) Rear Variable progressive system with mono-shock multiadjustable. Suspension stroke Front 177 mm. Rear 164 mm. Front fork oil SAE 5. Front fork oil level ø 40 mm.(125 / 200) 180 mm. air chamber steel bar ø 40 mm. (250 / 280 / 300) 160 mm. air chamber aluminium bar BRAKES Type Disc brake. Disc diameter Front ø185 mm. 4 piston calipers. Rear ø150 mm. 2 piston calipers. DIMENSIONS Overall height 1180 mm. Overall width 820 mm. Seat height 650 mm. Ground clearance 315 mm. Wheelbase 1330 mm. Fuel tank capacity 3,1 liters.

Incoming search terms:

Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Upgrading the Suspension on the Kawasaki ER6-F/ N

0

Filed Under (Kawasaki) by admin on 30-11-2010

download
Top fork is as removed. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Before removing the fork from the clamps on the yokes I loosened the fork top. Before removing the fork top the fork-slider was placed in a vice and the bottom bolt loosened….. … before finally being removed with the fork upside down. Because the springs were still in situ this gave sufficient tension on the damper-rod to prevent it from turning and allow the bolt to be removed. When I turned the fork the right-way up to remove the fork-top I did it over a container to catch the oil. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource All the OE components that will no longer be required. Left to right. Fork-top, spacer tube, washer, spring, damper-rod. Bottom bolts get re-used. Old and new, laid-out for comparison. The damper unit, minus spring and fork-top, drops inside the stanchion and slider. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Then the bolt goes back in, as tight as possible, to secure it. Top fork is done, second one awaits. Note the spring seat on the right, just below the spring. This drops over the damping rod after the oil has been added. The small locking-nut screws over the threaded part of the damping-rod next, all the way to the bottom. Spring drops in and then the fork-top screws on to the damping-rod as well, all the way down to the lock-nut which is used to secure it. At this point the stanchion is extended to the fork-top which is screwed in. Job done.

Incoming search terms:

HARLEY DAVIDSON LOCKING FUEL FILLER CAP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION 1. Prior to installing the gas cap on the vehicle, insert the key into the lock. Firmly grasp the chrome top of the fuel cap and turn the key until it stops. On right hand threaded fuel caps, turn the key counter-clockwise until it stops. On left hand threaded fuel caps, turn the key clockwise until it stops. This assures an unlocked position for the gas cap. Allow the key to return to the neutral position. 2. Remove the key and install the fuel cap on the vehicle. is00770 Figure 1. Right Hand Threaded Fuel Cap Installation NOTE When installing the fuel cap, rotate the cap one full turn past the audible click. This automatically positions gas cap to lock position. A properly locked/installed gas cap will rotate freely in both directions. Failure to do so will give an incorrect assumption that the fuel cap does not work properly. REMOVAL On right hand threaded fuel caps, insert key, and while holding the gas cap in place with hand, turn key counterclockwise until it stops, return key to original position. Gas cap must rotate 270 degrees counter-clockwise before mechanism engages to allow gas cap removal. Continue to rotate counterclockwise to fully remove gas cap. On left hand threaded fuel caps, insert key and while holding the gas cap in place with hand, turn key clockwise until it stops, return key to original position. Gas cap must rotate 270 degrees clockwise before mechanism engages to allow gas cap removal. Continue to rotate clockwise to fully remove gas cap. REPLACEMENT KEYS Record the 4 digit key number stamped on the back of the key opposite the Harley-Davidson logo, in the area provided below. If a replacement key is needed, see your Harley-Davidson Dealer with the 4 digit number to order a replacement

Incoming search terms:

Kawasaki Exhausts – ZX-6 ZX-10 Zx-14 Exhaust – Slip-ons INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Our favorite exhaust options for Kawasaki ZX Ninjas – ZX-10,ZX-6r, and the new horsepower king, Zx-14.. Grab your horsepower today. We love Rob Muzzy and Muzzy Exhausts.Going back to Doug Chandler and Scott Russell, Muzzy has been synonomous with Kawasaki and performance – and for years, if you rode Kawasaki,and you were on the podium, Muzzy was on your exhaust. We also feature Arrow and Yoshimura exhausts for your ZX-6R, ZX-10 and ZX-14. We love the sound of a Yosh exhaust on any Kawasaki Ninja. Yoshimura Oval (RS-3) Race Slip-On for Kawasaki ZX14R 2006 The easiest and least expensive way to experience Yoshimura performance is with our Slip-On/Bolt-On lines. Bolt-On style bolts to the O. E. M. mid-pipe Slip-On style with its stainless steel easily attaches to the mid-pipe RS-1 is available where noted Usually, no jetting or re-programming is required and installation is a snap Hindle Stainless Exhaust High Head Pipes – Kawasaki ZX6R-RR 03-04 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo North Denver News http://northdenvernews.com Powered by Joomla! Generated: 19 October, 2010, 12:28 Hindle Stainless Exhaust Low Head Pipes – Kawasaki ZX9R 00-03 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo

Incoming search terms:

42MM MIKUNI FLATSLIDE CARBURETOR INSTRUCTIONS

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at 1/2 to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle. The output of the OEM fuel pump is too high and will cause fuel overflow in the HSR carb, resulting in a possible dangerous fire hazard

Incoming search terms:

GAS GAS TXT BOY ENGLISH USER MANUAL

0

Filed Under (Gas Gas) by admin on 27-11-2010

download
Quick Guide to Maintenance Coolant liquid Coolant liquid -30ºC Crankcase oil (10w40) 500 cc. Electrode separation 0.6 mm. Forks suspension oil SAE 5 (Summer) SAE 2.5 (Winter) Fork suspension oil quantity200 cm3 Shock absorber spring length96 mm Front wheel pressure Standard 0.400 bar Competition 0.370 bar Rear wheel pressure Standard 0.350 bar Competition 0.300 bar -9- 1 Fuel – Petrol/oil mixture The motorcycle is fitted with a two-stroke internal combustion engine. This type of engine requires a mixture of petrol and oil. To ensure the correct working of the engine, the following are recommended: – Use high quality petrol, with an octane rating equal to or above 90 (RON + MON)/2 or 98 (RON). – Use 2T synthetic oil. Warning: – If the recommended oil is not available, use semi-synthetic oil. – Do not mix different oil-types. Mixture ratio: oil, 1.5% of petrol volume (50 parts petrol to every 0.75 part oil). Note: we recommend first preparing the mixture in a suitable container and then filling the fuel tank. Fuel tank This has a rapid access cap A and a vent hose B to allow gases produced in the tank to escape. – To open the cap, lift the clip in the direction shown by the arrow and turn to the left. Warning! Regularly check the cap seal and vent hose to ensure they are leak proof. Risk of spillage. -10- 3 2 Reserve Open Closed Fuel tap This has three positions: open, closed and reserve. The diagrams below show the position of tap A for each case. A Gear shift The motorcycle has a two- speed gearbox, which may be selected manually when the motorcycle is stationary, by moving the lever A in a horizontal direction, as shown by the arrow. Note: Select the gear according to the characteristics of the track

HARLEY DAVIDSON FLUSH-MOUNT LED FUEL GAUGE AND GAS CAP KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Remove stock gas cap from fuel tank. 2. Clean and wipe inside surface of fuel tank filler cup, O-ring seal surface, and trim ring adhesive surface with a mixture of equal parts of isopropyl alcohol and distilled water. 3. See Figure 1. Install gas cap into fuel tank. is00407 Figure 1. Screw in Gas Cap is00466 Figure 2. Note Position of Arrow on Trim Ring 4. Push down on gas cap and rotate clockwise one-eighth of a turn to lock. To unlock, push down on gas cap and rotate counterclockwise one-eighth of a turn. 5. See Figure 2. Before removing adhesive backing, note position of arrow on inside diameter of chrome trim ring. NOTE As you rotate trim ring, you will see gaps between trim ring and fuel tank. Rotate trim ring to position that best eliminates gaps between fuel tank and trim ring. Rotation of trim ring should be minimal. 6. See Figure 3. With the arrow pointing toward front of motorcycle, rotate chrome trim ring slightly to determine best position of bottom chrome trim ring to contour of the fuel tank 7. See Figure 4. Mark position of chrome trim ring with masking tape or grease pencil. 8. Carefully cut masking tape with a hobby knife making sure not to scratch chrome trim ring or paint surface on fuel tank. 9. Peel off adhesive backing from chrome trim ring. 10. Using gas cap to center and masking tape (or grease pencil mark) to align, press chrome trim ring firmly into position for about ten seconds. 11. Peel off masking tape (or remove grease pencil mark) from chrome trim ring and fuel tank. 2 1 is00414a 1. Masking tape 2. Cut masking tape Figure 4. Align Trim Ring and Press into Place NOTE Allow adhesive trim ring to cure for about 5-7 minutes before you continue with kit installation. Install Flush-Mount LED Fuel Gauge 1. Remove the seat following the instructions in the service manual. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove stock fuel gauge. Refer to service manual for instructions. 4. Insert wires down tube of fuel tank from LED fuel gauge. 5. See Figure 5 and Figure 6. Insert LED fuel gauge in the fuel tank cup

Incoming search terms:

Incoming search terms: