general motors mufflers baffles

You search Auto repair manual PDF general motors mufflers baffles, if there are search results will appear below. If search results do not exist, please search by others keyword.



  general motors mufflers baffles Direct Download speed 5282 Kb/s

  general motors mufflers baffles Full Version speed 6162 Kb/s



HARLEY DAVIDSON DYNA STREET PERFORMANCE SLIP-ON ACCESSORY MUFFLERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
PRODUCT INFORMATION Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. Noise Emission Warranty Harley-Davidson warrants that these mufflers, at the time of sale, meets all applicable United States E.P.A. Federal noise and Emissions standards. This warranty extends to the first person who buys these mufflers for purposes other than resale, and to all subsequent buyers. Warranty claims should be directed to an authorized Harley-Davidson Dealer. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances. INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 2. Loosen stock muffler clamps and remove nuts that attach mufflers to muffler support tube. Remove stock mufflers. Save all mounting hardware for reinstallation. 3. Install new kit mufflers using muffler clamps (purchased separately) and stock mounting hardware saved from Step 2. Do not tighten hardware at this time. NOTE Before tightening nuts that attach mufflers to muffler support tubes, make sure the front muffler is positioned as far forward in its brackets slot as possible. This will eliminate any possible contact between the mufflers. 4. Tighten muffler clamp bolts to 45-60 ft-lbs (61-81 Nm) . Tighten nuts that attach mufflers to muffler support tube snugly. 5. Connect the negative (-) battery cable

HARLEY DAVIDSON DYNA SLIP-ON ACCESSORY MUFFLERS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 2. Loosen stock muffler clamps and remove nuts that attach mufflers to muffler support tube. Remove stock mufflers. Save all mounting hardware for reinstallation. -J04263 3. Install new kit mufflers using muffler clamps (purchased separately) and stock mounting hardware saved from Step 2. Do not tighten hardware at this time. NOTE Before tightening nuts that attach mufflers to muffler support tubes, make sure the front muffler is positioned as far forward in its brackets slot as possible. This will eliminate any possible contact between the mufflers. 4. Tighten muffler clamp bolts to 45-60 ft-lbs (61-81 Nm) . Tighten nuts that attach mufflers to muffler support tube snugly. 5. Connect the negative (-) battery cable

HARLEY DAVIDSON SOFTAIL MUFFLER SLIP-FIT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
1. Disconnect negative battery cable. Perform this installation when the engine is cool. Installing these mufflers when the engine is hot could cause burns which could result in moderate to minor injury. 2. Remove mufflers according to applicable Service Manual instructions. Shotgun exhaust mufflers will come off the vehicle as a pair, attached together. Staggered dual mufflers will come off the vehicle attached to the interconnect tube. 3. For a shotgun exhaust, skip to Step 6. 1 CAUTION 1 WARNING 1 WARNING 1 of 2 4. Remove mufflers from interconnect tube and discard gaskets and mufflers. 5. Install mufflers to interconnect pipe using new gaskets (6) and existing screws. Slip muffler clamps (1) on mufflers and install assembly back on vehicle. Tighten screws to 96-120 in-lbs (10.8-13.6 N-m). Tighten muffler clamps to 45-60 ft-lbs (61-81.3 Nm). Attach the interconnect tube to the frame using the existing flange lock nuts and washers. Tighten to 30-33 ft-lbs (40.7- 44.7 Nm). 6. On shotgun style assemblies, assemble top and bottom mufflers using interconnect seal. Torque screws to 96-120 in-lbs (61-81.3 Nm). Attach interconnect tube to frame using existing flange locknuts and washers. Torque to 30-33 ft-lbs, (40-7-44.7 Nm). 7. Replace fasteners and tighten as follows: muffler clamps to 45-60 ft-lbs (61-81.3 Nm), flange locknut on carriage bolt to 30-33 ft-lbs (40.7-44.7 Nm) and tighten screws and washers to 15-19 ft-lbs (20.3-25.8 Nm). 8. Reconnect negative battery cable. Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. Noise Emission Warranty Gabilan Manufacturing, Inc. warrants that these mufflers, at the time of sale, meet all applicable United States E.P.A. Federal noise standards. This warranty extends to the first person who buys these mufflers for purposes other than resale, and to all subsequent buyers. Warranty claims should be directed to an authorized Harley-Davidson Dealer. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances.

Fitting new GL1500 Mufflers Installation Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
The stock mufflers on the GL1500 Goldwing tend to rust after a few years. It doesn’t really matter how much you clean them because the design means that they tend to collect condensation which turns into water, then the dreaded tinworm rots them from the inside out. There is a drain hole in each muffler (near the front) to allow some water out, but the hole is really in the wrong place as the mufflers almost always rot at the ends near where the tailpipe is welded on. Replacing mufflers on the GL1500 Goldwing is easy enough and you really don’t need a tutorial for the task. But I did have a camera handy on the day I did the job so you may as well have the benefit of the images. This is a common sight on a GL1500 Goldwing. The mufflers rot from the inside out and eventually the ends just blow off. Believe it or not, these mufflers are on a 1997 GL1500SE with only 7,700 miles that was always stored in a dry garage! I replaced them in April 2004 and they had been almost as bad as this since 2002, but the owner of the Goldwing wasn’t using it much so he didn’t bother replacing them until 2004

BMW R1200 GS Rider's Manual

0

Filed Under (BMW) by admin on 28-11-2010

download
General view, left side 1 Adjuster, springpreload, front (63) 2 Adjustment of windscreen (60) 3 Adjuster for headlight beam throw (underneath the in- strumentpanel) (69) 4 Clutch-fluid reservoir (116) 5 Type plate (on frame, behind side cover) 6 Seat lock (69) 7 Power socket (96) 8 Adjuster for damping characteristic, rear suspension (64) 9 Engine-oil filler neck (110) 10 Engine oil level indicator (109) 2 11 z General views
2 12 z General views General view, right side 1 Adjuster for springpreload, rear (63) 2 Fuel filler neck (84) 3 Brake-fluid reservoir, front (114) 4 Vehicle Identification Number (VIN) (on steering-head bearing) 5 Air filter (behind right side panel) (132) 6 Brake-fluid reservoir, rear (115) 2 13 z General views Underneath the seat 1 Rider’sManual 2 Battery (135) 3 Toolkit, Payload table (in tool tray), Tyre pressures table (in tool tray) 4 Helmet holder (71) 2 14 z General views Handlebar fitting, left 1 Operating the odometer (47), Operating the on- boardcomputerOE (49) 2 Operating the ABSOE (56), Operating ASCOE (58) 3 Operating ESAOE (66) 4 Horn 5 Flashing turn indicators, left (54), Hazard warn- ingflashers (55) 6 Headlight flasher and high- beam headlight (53) 2 15 z General views Handlebar fitting, right 1 Emergency off switch (kill switch) (56) 2 Starter button (76) 3 Grip heating 4 Flashing turn indicators, right (55), Hazard warn- ingflashers (55) 5 Cancel button, flashing turn indicators (55), Pushbut- ton, cancel hazard warning flashers (56)

Harley Davidson Sportster Straightshots HS Slip-on Exhaust system

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Loosen, but do not remove, the two head pipe mounting nuts from each flange located at the cylinder head. 3. Remove the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 4. Loosen the clamp holding the mufflers onto the head pipes. Page 1 of 4 D480IN Rev. 1.0 Sportster Straightshots HS Slip-on Exhaust system Part #16819 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: 1/2″ combination wrench 3/8″ drive ratchet and 9″ extension 9/16″ and 1/2″ sockets 5/16″ Nutdriver/flat blade screwdriver 5. Remove the two bolts from each muffler which attach the mufflers to the mounting bar. 6. Remove the mufflers by sliding them off the head pipes. 7. Remove the clamp from the nose of each muffler (these will be re-used when installing the new mufflers). 8. Remove the gaskets from the crossover ports on the stock mufflers. Inspect the gaskets and replace if damaged or worn (H-D part #65927-00). 9. Install crossover gaskets onto mounting bar on motorcycle. VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Remove mufflers and heat shields from protective packaging. 2. Slide the nut plate inside the bracket that is welded to the backside of each muffler body and attach the muffler bodies to the mounting brackets (stamped 379-P) using four 5/16″ x 5/8″ flange head bolts (supplied). Leave them loose at this time (Figure 1). 3. Slide stock exhaust clamp onto nose of each muffler. 4. Slide mufflers onto head pipes and align crossover port with gasket on mounting bar (Figure 2). Press into place on gasket. 5. Attach the muffler brackets to the stock mounting bar using four 5/16″ x 3/4″ hex head bolts, washers, and nuts (supplied). Leave them loose at this time (Figure 3). 6. Tighten cylinder port exhaust flange nuts on front and rear cylinders. 7. Install and tighten the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 8. Align muffler and bracket so they sit level. Tighten the muffler mounting bolts and the bracket mounting bolts. 9. Tighten the clamp holding the muffler onto the head pipe.

Incoming search terms:

HARLEY DAVIDSON SPORTSTER MUFFLER SLIP-ON KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect negative (-) battery cable. 2. Remove mufflers using appropriate service manual instructions. 3. Discard gaskets and mufflers. 4. Install new gaskets on mufflers. 5. Slip muffler clamps on mufflers. 6. Loosely attach mufflers to the interconnect tube using existing screws and washers. 7. Position the ends of the front and rear exhaust pipes into front and rear cylinder heads and align exhaust system while tightening all nuts and bolts, beginning at the cylinder head exhaust ports and work back toward the mufflers. a. Finger tighten the upper nuts to the mounting studs. b. Tighten the lower nut to 9-18 in-lbs (1.0-2.1 Nm) . c. Tighten the upper nut to 60-80 in-lbs (6.8-9.0 Nm) . d. Tighten the lower nut to 60-80 in-lbs (6.8-9.0 Nm) . 8. Tighten the acorn nut on the rear exhaust pipe support clamp to 15-19 ft-lbs (20.3-25.8 Nm) . 9. Tighten muffler clamps to 45-60 ft-lbs (61.0-81.3 Nm) . 10. Tighten screws and washers to 15-19 ft-lbs (20.3-25.8 Nm) . 11. Connect negative (-) battery cable.

Suzuki INTRUDER 1400 SLIP-ON EXHAUST SYSTEM Installation Manual

0

Filed Under (Suzuki) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosenthe mounting bolt and pinch clamp on both left and right hand mufflers. 2. Loosenthe clamp on the crossover tube, located between the two mufflers. 3. Remove the two nuts that mount the front head pipe flange to the cylinder head. 4. Remove the two nuts that mount the rear head pipe flange to the cylinder head. 5. Remove the head pipes using a twisting motion to break the seal at the muffler and to clear the cylinder head. Note : If the exhaust coupler gaskets did not remain in the mufflers, remove them from the head pipes at this time. These coupler gaskets will not be reused in your new exhaust system. 6. Remove the mounting bolt from the left hand muffler. Remove the muffler, again using a twisting motion to seperate the crossover tube and set the muffler aside. (Save the stock mounting hardware for reuse). 7. Repeat step #6 on the the right hand muffler. Set the muffler aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 2. Reinstall the stock head pipes to the engine. Note : Leave the flange nuts loose at this time. 3. Remove the mufflers from their boxes. There are a left and right hand muffler in this system. To define the difference between the left and right mufflers, check the bracket that is welded to the back side of the muffler. Each muffler is stamped with it’s own part number. Part # D500 is the RIGHT muffler and Part # D550 is the LEFTmuffler. 4. Install a three hole mounting bracket to each of the mufflers. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16 flange head bolts (supplied), leave them loose at this time. Note : Each muffler bracket has a number stamped on it, #179 bracket is for the left hand muffler and #180 is for the right hand muffler. When the brackets are mounted correctly, the end of the bracket with the single hole should point to the inlet end (small end) of the muffler. Refer to figure 1.

HARLEY DAVIDSON SPORTSTER® ACCESSORY SLIP-ON MUFFLER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect negative (-) battery cable. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 2. Remove mufflers using appropriate Service Manual instructions. 3. Discard gaskets and mufflers. 4. Install new gaskets on mufflers. 5. Slip muffler clamps on mufflers. 6. Loosely attach mufflers to the interconnect tube using existing screws and washers. 7. Position the ends of the front and rear exhaust pipes into front and rear cylinder heads and align exhaust system while tightening all nuts and bolts; begin at the cylinder head exhaust ports and work back toward the mufflers. a. Finger tighten the upper nuts to the mounting studs. b. Tighten the lower nut to 9-18 in-lbs (1.0-2.1 Nm) . c. Tighten the upper nut to 60-80 in-lbs (6.8-9.0 Nm) . d. Tighten the lower nut to 60-80 in-lbs (6.8-9.0 Nm) . 8. Tighten the acorn nut on the rear exhaust pipe support clamp to 15-19 ft-lbs (20.3-25.8 Nm) . 9. Tighten muffler clamps to 45-60 ft-lbs (61-81.3 Nm) . 10. Tighten screws and washers to 15-19 ft-lbs (20.3-25.8 Nm)

POLINI X1 GENERAL INFORMATION AND SPECIFICATIONS

0

Filed Under (Polini) by admin on 02-12-2010

download
Air cleaner – Clean and reoil daily or after each moto to prevent motor failure and reduced performance. Transmission oil – change after every race, or at end of riding day. Chain – check tension and lubricate before every ride, adjust or replace as needed. Reoil after riding in damp conditions. Clutch – disassemble and clean clutch assembly frequently, every 2-3 races at least. Inspect kickstarter gears at this time. Ignition cover – remove cover and wipe dry after each ride or after washing bike to remove condensation. Piston rings – replace as often as every 3-5 races with expert rider, less often with less aggressive riders. Piston, pin, rod bearing & circlips – replace as often as every 8-10 races with expert rider, less often with less aggressive riders. Coolant – change yearly, make sure there is at least a 50/50 mixture of antifreeze if freezing temperatures are possible. Steering bearings – Check daily for looseness or play. Adjust and regrease as needed. Swingarm – Check often for looseness. Regrease several times a year. Replace bushings if any play is evident. Sprockets – check for worn or curved teeth each time chain is adjusted. Chain roller& wear pads – check roller for free rotation when checking chain. Make sure roller is not bent or damaged. Check chain wear strips on swingarm and chain guide frequently. Replace as needed to prevent chain from damaging motorcycle. Spokes – Check after each race or after each day of riding for looseness or damage. Wheels & tires – check wheels after each race for dents, cracks or other damage. Check tires for cuts, damage or wear. Check tire pressure daily and adjust for riding conditions. Shock – Check shaft area daily for signs of oil leakage or damage. Check swingarm and shock bushings for looseness. Forks – Check forks daily for leaking oil or damage to tubes. Make sure forks are not twisted check for smooth operation. Spark plug – check sparkplug color and condition after each race or end of riding day. Adjust jetting to keep plug from fouling or overheating. Silencer – If bike seems to be getting louder, replace packing and decarbonize inner tube. Expansion pipe – check daily for large dents, damage or leakage. Remove carbon from headpipe when pipe is removed. Have large dents fixed, or any dents within 8″ of the cylinder. Replace o-rings on pipe as needed to maintain a good seal. Footpegs – check daily for proper operation, pegs should spring back into place. Make sure pegs are not bent or overly dull. Handlebars – check bars after any crash for bending. Look for cracks near bar clamps. Replace bars that have been straightened more than 2 or three times, or if bar is badly bent. Aweakened bar can snap suddenly causing injury to rider. Throttle – check throttle for proper operation each time before bike is started. Remove and clean inside of grip and bar as needed. Grips – check grips daily for wear or looseness. Replace as needed. Use grip glue & safety wire to help hold grips in position. Calipers & pads – check pad wear and caliper function daily or after each race. Replace pads and clean calipers as needed. Brake lever – check lever daily for damage or wear. Make sure lever is at proper angle for both seated and standing positions. Leave lever clamp loose enough to allow clamp to rotate during crash rather than breaking lever. Check and adjust freeplay as needed. Brake pedal – Check pedal daily for damage and proper freeplay. Adjust rear caliper as needed. Reeds – Remove and inspect reed block during every ring change. Check reeds for signs of wear, fraying and cracking. Make sure reeds sit flat and seal well. Replace at any sign of wear or damage or at least once a year, more often for expert riders. Nuts & bolts – Check all nuts and bolts regularly. Make sure to check engine mounting bolts and swingarm bolt frequently

Incoming search terms: