gl1500 drain hoses

You search Auto repair manual PDF gl1500 drain hoses, if there are search results will appear below. If search results do not exist, please search by others keyword.



  gl1500 drain hoses Direct Download speed 5282 Kb/s

  gl1500 drain hoses Full Version speed 6162 Kb/s



HARLEY DAVIDSON BRAIDED OIL HOSES INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery negative cable. 2. Drain engine oil according to Service Manual instructions. 3. Removing the rear exhaust pipe may aid in giving access to the oil lines and fittings. If necessary, remove the rear exhaust pipe according to Service Manual instructions. 4. See Figure 5 and Figure 1 for description and location of the three oil hoses that are replaced with the braided hoses in this kit. Remove the original equipment oil feed, return and vent lines. 5. See Figure 2. Remove and discard the original hex threaded quick disconnect fittings (1), (2) and (3) at the engine for each of the hoses removed in Step 4. To remove the fittings, turn the hex in a counterclockwise direction until free. 6. See Figure 5. Install the threaded adapter from the kit onto the corresponding oil line. The adapters for the return and vent lines are the same size. The adapter for the feed line is larger in size. Coat the male threads of the adapters with Loctite 565 thread sealant. NOTE Be sure to install hoses on the correct fittings. If you mix up the hoses, you will change the direction of the engine oil flow, causing severe engine damage. 2 3 1 is04165 1. Oil Return Hose 2. Oil Feed Hose 3. Oil Vent Hose Figure 1. Installed Oil Hoses

Fitting new GL1500 Mufflers Installation Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
The stock mufflers on the GL1500 Goldwing tend to rust after a few years. It doesn’t really matter how much you clean them because the design means that they tend to collect condensation which turns into water, then the dreaded tinworm rots them from the inside out. There is a drain hole in each muffler (near the front) to allow some water out, but the hole is really in the wrong place as the mufflers almost always rot at the ends near where the tailpipe is welded on. Replacing mufflers on the GL1500 Goldwing is easy enough and you really don’t need a tutorial for the task. But I did have a camera handy on the day I did the job so you may as well have the benefit of the images. This is a common sight on a GL1500 Goldwing. The mufflers rot from the inside out and eventually the ends just blow off. Believe it or not, these mufflers are on a 1997 GL1500SE with only 7,700 miles that was always stored in a dry garage! I replaced them in April 2004 and they had been almost as bad as this since 2002, but the owner of the Goldwing wasn’t using it much so he didn’t bother replacing them until 2004

Wildfire WFH 150-T Touring Scooter Specification And Owner's Manual

0

Filed Under (Wildfire) by admin on 29-11-2010

download
Engine Oil Replacement • Replace the engine oil after the first 50 miles or 1 hour with 5w50, 10w50 or 15W50 synthetic engine oil. Then replace again every 1,500 miles or 1 each year. Check oil level every 500 miles, add oil if needed. Changing the Engine Oil (1).Warm up the engine for a few minutes. (2).Stop the engine. (3). Place scooter on center stand. (4).Place an oil pan under the engine and remove the dipstick. (5).Remove the drain plug and drain the oil. Reach in drain hole, pull out filter clean and reinstall, after all oil drains out. (6).Reinstall drain plug. (7). Fill the engine with oil until the level is in the designated area on the dipstick. (8).Start the engine and check for oil leaks. If a leak is found stop the engine immediately and look for cause. Rear Wheel Oil Replacement • Replace the gear oil after the first 500 miles with 5W/50 synthetic engine oil. Replace the gear oil again every 4 months or every 2000 miles. • Replacing the Gear Oil (1).Put the scooter on the center stand (please see photo below) . (2).Place an oil pan under the gear case (please see photo below) . (3).Remove the oil filler bolt and the drain plug to drain the oil (please see photo below) . (4).Reinstall and tighten the drain plug. (5).Fill the gear case with oil (please see photo below) . (6).Reinstall the oil filler bolt. (7).Check for oil leakage. Cleaning Air Cleaner Be sure to check the air cleaner regularly. (1).Place the scooter on the center stand. (2).Unscrew and remove the left side panel. (3).Remove the air cleaner cover by removing the screws. (4).Take out the air cleaner by removing the screws. (5).Remove the air cleaner element and wash it gently, but thoroughly in solvent. Replace if damaged. (6).Squeeze out the excess solvent and dry it. (7).Apply oil to the entire surface of the air cleaner and squeeze out the excess oil. It should be damp but not dripping. (8).Install the air cleaner, cleaner cover, and left side panel. center stand 1 oil pan 2 3 oil drain plug oil pan 5 Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed.

HONDA GOLD WING GL1500 AND GL1800 TRIKE CONVERSION KIT Owner's Maintenance Notes

0

Filed Under (Honda) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 20-25 psi. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm and wheel bearings are sealed and do not require greasing. However, should you experience unusual wheel bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Rear end lubrication . Your differential comes filled with 1 quart of SAE 85W140 API GL-6 gear oil. You should not have to top-off the differential unless you experience axle seal or pinion seal leaks. Check the oil level every 10,000 miles, or sooner if you experience leaks, and refill as necessary. Do not fill higher than the fill-hole. Change the differential oil every 30,000 – 35,000 miles. 5. Brakes . Check your front and rear brake system fluid levels every 3,000 miles and top-off as necessary. Inspect brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . If your driveshaft U-joint and/or splines are fitted with grease fittings, pump the fittings with wheel-bearing, graphite or high-pressure grease every 3000 to 5,000 miles. If yours does not have grease fittings then lubrication is not required. 7. Suspension System : The suspension system is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight): GL1500: The OEM adjustable air shock is used in conjunction with two (2) new Progressive 416 air shocks. The three shocks should be pressurized to about 20 psig, but to no more than 70 psig; GL1800: You can still use your OEM mono-shock pre-load adjustment. Your two (2) new coil-over shocks do not have an air system connection. However, there is a pre-load adjuster ring on each new shock that is factory-set at the “lowest” setting, for the softest ride. Changing this setting will result in a stiffer ride. 8. EZ-Steer (rake kit) : If your trike is equipped with Champion’s EZ-Steer, the bearings are a wear item. You should follow your motorcycle manufacturer’s recommended front-end triple-tree maintenance requirements. Generally these call for an initial service at 1,000 miles followed by periodic maintenance at 10,000 mile intervals. 9. Electrical : Your trike is pre-wired for a trailer connection. The harness is just below the trunk door on the underside of the body.

Incoming search terms:

HONDA GL1500 FRONT WHEEL INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 27-02-2011

download
1. Rotor Covers. Tri-chromed ABS rotor covers replace the painted ones. Light weight, beautiful and functional. Include a rear strap and sold in pairs. Also, available are chrome rotor covers with amber strip lights installed. Fits 1988 to 2000. 2. Fork Light Mounts . Specially designed mounts are tri-chromed metal and hold a total of 6 lights. Lights not included. Sold in pairs 3. LED Lighted Rotor Cover Trim Rings . NEW Update your bike with LED lights. Tri-chromed ABS rings include amber or red, blue and amber LED lights. Sold in Pairs 5. 252-216 Rotor cover Plugs. These¾” chromed steel plugs fill the holes on the GL1500 rotor covers. Sold in a 4 pack

HONDA GL1500 Radio Knobs Installation Manual

0

Filed Under (Honda) by admin on 28-02-2011

download
NOTE: Read instructions carefully before installing. 1. Place bike on center stand. Remove the 5 original knobs. 2. Using needle nose pliers, remove the knob stops from the 2 left hand knob sockets. 3. Install replacement chrome knobs. ® Installation Instructions For Part 15673-235 GL1500 Radio Knobs

Balancing Honda GL1500 Carburetor Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
First pry off the plastic clip covering the screw as in the first picture. Note the type of screw used, as shown in the third picture. You must put this one back in the right place. Tip; When refitting this clip later on, a bit of Blutack or similar will stop it falling off and getting lost. Pull the L piece trim away, taking care not to break the tab shown in the fifth picture Now pry off the small black plastic cover at the rear of the running light. Blutack will be a good idea here as well when refitting the cover. The owner of this GL1500 didn’t use it and the cover on each side of the Goldwing got lost, which is why you can’t see them in the pictures. Note the type of screw used here as well, same as the one mentioned earlier. The third picture shows the two normal Phillips screws at the front of the running light, remove them. Remove the running light and pull the lower fairing panel away Remove the rubber plug from the right side fan. The adjuster screw for balancing the carbs is about 6″ behind and up, and hard to see. I removed the fan so I could get the camera in and the second picture shows the adjuster screw

Honda GL1500 EZ Steer Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
1. Use the Parts Checklist included with your hardware to verify the contents of the box 2. Remove the front wheel, fender, forks and triple clamps as shown in the Honda Shop Manual. Torque head bearings to 30 ft-lb. 3. Replace the stock fork caps using new seals with the extended caps provided. If you do not already have Progressive fork springs we suggest they be installed for the best results. 4. Install the new triple clamps. Remember to grease the new lower steering bearing. 5. Install the forks into the new triple clamps. Be sure to torque all pinch bolts to factory specifications. Do not over tighten as this can cause undue stress on the new triple clamps. 6. Check the steering lock action by turning the forks fully in both directions. Because of manufacturing tolerances in the fairing mounting bracket the fork tubes sometimes make contact with it at full lock. Usually this can be overcome by giving the handlebar a slight push while engaging the lock. 7. Because the fork tubes are now longer than stock, DO NOT use the clamps that held the brake lines to the stock lower triple clamp. Some models have a temperature sensor mounted under the fairing that may interfere with the plastic cable guide. If interference is noted trim the guide as required. 8. Install the fender and wheel assembly. Be sure the brake hoses are routed to allow full travel of the forks. It is necessary to trim the two upper ears off of the fender upper cover to prevent contact with the fairing during turns. 9. If you have questions please call our EZ-Steer Maintenance The bearings in your EZ-Steer rake kit are normal wear items, not subject to replacement under Champion’s one year Limited Warranty for the product. Failure to follow your motorcycle manufacturer’s recommendations for periodic OEM triple-tree maintenance will accelerate the wear on these bearings. Checking/adjustment of the steering stem nut torque, with the front end lifted, in accordance with your motorcycle manufacturer’s recommendations, is key to reliable bearing service

HONDA GL1500 Headlamp Adjustments Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
Headlamp Adjusting Procedure Tools needed • Long, slender #1 Phillips screwdriver (for adjusters behind the rubber plugs) • #2 Phillips screwdriver (for the other adjuster screw) • 12-inch square of cardboard • Flat wall or garage door • Paper, tape, marker NOTE: All adjustments are very fine. You have to turn the screws A LOT to see changes in adjustment. This procedure is best done after dark, because you will need to do some test rides. Preparation 1. Set the bike on its center stand, 10 feet away from an unobstructed wall or garage door, and square to the wall or door. 2. Remove the front fairing cover and lower vent grille to gain access to the headlamp adjusters. 3. Idle the engine or connect a battery charger to the battery, to prevent battery drain. Headlamp assembly viewed from the front, showing positions of mirrors and adjusters (pretend the lens has been removed) . Low Beam Vertical Alignment 1. With the lights on low beam, cover the right half of the lamp assembly with the cardboard square, so only the left bulb is shining on the wall. 2. Using a marker, mark the top of the left low beam on the wall (use paper taped to the wall if you don’t want to mark the wall itself) . 3. Move the cardboard so it blocks the left bulb, so only the right bulb is shining on the wall. 4. The top of the right low beam should be even with the mark you made for the left low beam. If it’s not, adjust by turning the screw behind the rubber plug at the top of the lamp assembly, using a long, slender #1 Phillips screwdriver. 5. Move the cardboard back and forth between the bulbs to verify that the low beams are at the same height. On high beam, the two hotspots should line up vertically. High Beam Vertical Adjustment 1. With the lights on high beam, note the position of the beams’ hot spots on the wall in relation to the mark you made in step 5 above. 2. Most owners complain about their low beams being too low on the roadway. To correct this, lower the high beams by turning the screw behind the rubber plug at the bottom of the headlamp assembly, using a long, slender #1 Phillips screwdriver. You can watch the high beam hot spot being lowered on the wall in relation to the mark you made. 3. Take a test ride. Get out on a dark street, and adjust the high beams using the dash knob until you like what you can see. Then switch to low beam and see how that looks. 4. Repeat these steps until you get the low beam pattern you want. Left/Right Adjustment 1. Back to the wall. Set the bike on its center stand at a distance of 25 feet from the wall and square to the wall. Center the front wheel. 2. Shine the high beams on the wall. 3. Step to the back of the bike, and level your eye with the center of the passenger backrest. Use the center of the backrest and the center of the windshield like a gunsight. The center of the hotspot of the high beam should hit the wall in this line. 4. Adjust by turning the uncovered screw at the bottom of the headlamp assembly, using a #2 Phillips screwdriver.

Incoming search terms:

Honda GL1500 Gold Wing Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 17-02-2011

download
REMOVAL OF ORIGINAL PARTS Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. • Left and right side-covers (to be re-installed with minor modification). • Seat (to be re-installed without modification). • Trunk. • Left and right passenger foot rests (to be re-installed without modification). • Left and right side-covers above passenger foot rests. • Battery and holder (to be re-installed without modification). • Left and right saddle bags (retain side cover mounting grommets for re-use). • Left and right mufflers. • Rear wheel. • Rear brake line to master cylinder.** • Reverse resistor assembly (to be relocated). • Swing Arm (Drive shaft boot will not be used). • Bank angle sensor. • Shocks. Air shock (non coil-over) to be reused. ** Thoroughly vacuum drain rear brake system, including feed line to left front caliper PREINSTALLATION PREPARATION 3.1 Modification to Trunk / Luggage Stay Removal from vehicle frame is not necessary. a. Cut the down tubes of the trunk stay and remove the lower section as shown in Figures 1 & 2 b. Trim rear upper tube-end rounded corners just outboard of welded nut. Trim line should be parallel with center line of vehicle. This will provide clearance for body when installed. Figure 2 (Inset) c. Remove the Hazard and Turn Signal relays from the center holder; bend Relay Holder Tab up 90°. Relays will be relocated to left and right sides. Figure 3 d. Disconnect and remove Bank Angle Sensor from its mount tab (Bank Angle Sensor will not be re-used). Cut wires midway between sensor and plug. e. On plug end, splice / connect red and green wires together to close the circuit. f. Cut and remove the Bank Angle Sensor mount tab from the Trunk stay. Figure 4 3.2 Modification to Rear Inner Fender Removal of fender and attached parts is not necessary for modification. a. Place supplied template (See last page) on fender (left and right sides) as shown and mark outline. With box cutter, cut fender along template outline. Once material is removed, make a vertical cut up the side (line indicated by arrow Figure 5) of the fender. Do not continue cut across top of fender. Figure 5 b. Carefully heat underside of fender with heat gun and bend fender upward until aft end contacts frame cross member. c. Drill holes in plastic fender through cross brace at locations indicated and secure fender to cross with zip ties. Figure 6