handle bar ajustment road glide

You search Auto repair manual PDF handle bar ajustment road glide, if there are search results will appear below. If search results do not exist, please search by others keyword.



  handle bar ajustment road glide Direct Download speed 5282 Kb/s

  handle bar ajustment road glide Full Version speed 6162 Kb/s



V-Star 1100 And Dragstar 1100 Modification V-Star Driving/ Passing Lights Factory Chrome Light Bar Cover Installation

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Use a rotary tool to widen the fastening area of the lower backside clips on the cover. The total width between the clips should be 4 æ inches. Trim off º inch on both inside ends of the lower backside attachment clips. Trim the clips equally. The following picture shows a modified cover. Narrow the clips on both ends to fit over the welds on the bar. The cover will not attach to the bar if the width between the clips is too narrow. If the width is too wide the cover may slide sideways on the bar. Narrow both clips equally to center the cover over the welds on the lower edge of the bar. The top of the cover is modified to allow the cover to fit over the bolts on the light bar. The top edge of the cover is filed æ inch deep and 5/8 inch wide to fit over the bolts. The back top edge is filed or ground 1/8 inch to fit over the light bar fastening bracket. Use care when filing chrome covered plastic. The following picture will help to complete this step in the modification. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. The ends of the cover are modified to allow the cover to fit over the upward curved light bar. The upper openings on the ends of the cover that fit over the bar must be filed to enlarge the area. Grinding the cover ends will allow the cover to fit and clip onto the bar. The end openings are filed or ground at an angle to match the slope of the bar. This picture shows the outer end of the cover. The ends of this cover have been modified by enlarging the area on the upper edges to fit over the upward curving light bar. The ends must be enlarged 1/8 inch on the top edge. The cover edge can be slanted upward to match the curved bar. Modify the cover ends until it fits without the outer chrome cover touching the bar. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Sometimes the modified light bar cover may touch the bottom of the headlight. Modify the cover, or adjust the bar or headlight if you notice the headlight touching the bar cover. This modification makes the V-Star motorcycle with Yamaha driving lights look better. The light bar bolts are covered and the chrome cover improves the appearance of the front of your bike. Other V-Star riders will notice how nice the front of your bike looks with the chrome light bar cover installed

Incoming search terms:

Harley Davidson FL series Electra Glide, Ultra Classic, Road King, Road Glide Left and Right Mounting Plate Installation Installation Manual

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove existing control arm end cap and grind the outside flush. See picture below for reference. The swing arm will drop if both sides are removed at the same time. To ease installation, complete one side before starting on the other. Note: there is a left and right. Left and right end caps shown. 2. Install mounting plate assembly 10002351 on top of the end cap using 7/16″ hex head bolt and lock washer in the bottom hole. Use the 7/16″ counter sink bolt in the top hole. Make sure the end cap is seated properly. The end cap notch should fit into the recess on the frame. The pivot arm assembly is shipped on mounting plate assembly; you may remove the pivot arm to make installation easier. 3. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. Tighten both bolts to 25 ft lbs. (Further tightening will be required after the toe in is set). 4. If you removed the left hand pivot arm assembly, remount it now, 10002575-A (pg 20) with seal, bearings (2), washer, nut, cotter pin and dust cover. 5. Repeat for right hand side. 5 Toe In Adjustment Adjustment made with the mounting plates, bolts, pivot arms, and hubs (without wheels and tires) in place

Incoming search terms:

HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

Kawasaki VN2000 LIGHT BAR INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Make certain the motorcycle is securely positioned for this installation. Cover the front fender with a protective cloth to avoid scratches. 2 . Remove caps that cover the headlight screws. Remove headlight screws. (Small Screwdriver and #2 Phillips Screwdriver) Figure 1 and 2. 3. Disconnect headlight at two places. Set light aside. Figure 3. 4. Disconnect the Right (Orange) and Left (Blue) turn signal connectors. 5. Remove the Screws with the 8mm hex head that hold the turn signal bar to the under side of triple clamp. Remove turn signal bar. Bar and screws will not be re-used. (8mm Socket) Figure 4. PREPARATION INSTALLATION 6. Mount the Light Bar Assembly. Hold Light Bar in place at underside of triple clamp. Use the M6 x 16 Screws with a Flat Washer to install the Light Bar assembly. Tighten Firmly. (5mm Hex Key) Figure 5. 7. Route the Light Bar Wires to the back and into headlight shell. WIRE LIGHT BAR HELPFUL WIRE TIPS: A. Keep the Right and Left Wires of the Light Bar in separate groups. B. Inside the headlight shell, the wires bundled in the Blue Connectors are for Right side operation and Orange Connector is Left. C. You will need to remove 2-3″ of electrical tape from the Blue/Yellow Stripe, Low Beam Wire inside the headlight to have room for two Scotchlok Connectors going to this wire. (Scissors) Figure 6

HARLEY DAVIDSON LIGHTED CHROME DIRECTIONAL BAR INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION 1. Disconnect turn signal wires at connectors located in directional bar. On 1994 and later models there are two wires for each turn signal lamp. Earlier models have only 1 wire per lamp. 2. Remove existing directional bar from motorcycle. Save all hardware for reattachment. If the turn signal connector is too large to be removed from the directional bar, remove the wires from the connector as follows: Bend back the connector latches on the sides of the connector slightly to free the secondary lock. Rotate the secondary lock outward on hinge to access terminals in chambers of connector housing. With a paper clip sharpened to a chisel point, insert the paper clip into the connector housing cavity until it stops. Pivot the end of the paper clip and gently tug on the wire to pull the terminal from the cavity. Do not tug on the wire until the tang that holds the terminal in the cavity is released. Take your time, a few tries may be required before you develop a feel for releasing the terminal from the connector. 3. Remove screws that mount turn signals lamps to existing directional bar. Remove lamps and turn signal wires (with their attached connector halves) from existing bar. 1 2 3 4 is02199 1. Ground wire 2. Hold lamp in place 3. Backing plate 4. Self-tapping screw Figure 1. Remove Backing Plate 4. See Figure 1. For each end of new directional bar, remove self-tapping screw that holds corner of backing plate and ground wire in place and remove backing plate. 1 2 is 02200 1. Hold lamp in place with this screw 2. Turn signal connector(s) are behind LED Figure 2. Assembling Directional Bar 5. See Figure 2. For each end of bar, place turn signal lamp in position with wires routed as shown. Move LED light out of the way and thread 5/32 inch Allen socket screw into lamp to hold lamp in place. Tighten screw.

HARLEY DAVIDSON TOURING DETACHABLE SISSY BAR UPRIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION NOTE The Detachable Sissy Bar Upright can be installed on either a two-point or four-point Docking Kit. 1. If not already in place, install the Detachable Docking Hardware Kit (either two-point or four-point) to the vehicle per the instructions in that kit. 2. See Figure 2. While standing behind the motorcycle, place the left-side and right-side front upright notches (with bushings in place) onto the docking points (A) inboard of the upper shock absorber mounts. Make sure the notch bushings (9) seat fully into the shock absorber docking points. 3. See Figure 2, arrows (D) and (E), and Figure 1. Position the rotary latches (4) over the rear docking points (3). Check to be sure the upright sides (1) and latches fit into the neck (7) of the rear docking points as shown. This may require some gentle squeezing or spreading of the sissy bar upright sides. NOTE After installing the sissy bar upright, check to be sure the sissy bar is secure. The front and rear docking points must be fully engaged. See Figure 1 for correct engagement. 4. Push the rear of the sissy bar downward and close the latches by pressing the latch lever as far forward as it will go. You will hear a “CLICK” when the latch is in place. If the latch does not easily close, do not force. Check the sissy bar alignment again, as described in steps 2 and 3. 5. To remove the sissy bar upright, press the release button (G) on each side and pull the latch levers back. Carefully lift the rear of the sissy bar up and pull the upright out of the front docking points

HARLEY DAVIDSON NARROW CHROME DIRECTIONAL BAR INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
This kit is designed for installation on 1986 and later FLST®, FLSTC®, FLSTN®and 1991 and later Touring models. (Except 2004 and later FLHRS®and FLTR®) NOTE: Will not fit when equipped with Flat Lens Turn Signal Module (Part Number 91699-99A). Installation 1. Disconnect turn signal wires. For 1999 and later models: See Figure 1. Remove taillight cover and disconnect turn signal wires at connectors shown in illustration. For 1998 and earlier models: Disconnect turn signal wires at connectors located in directional bar. On 1994 and later models there are two wires for each turn signal lamp. Earlier models have only 1 wire per lamp. 2. Remove existing directional bar from motorcycle and save hardware for re-installation. If the turn signal connector is too large to be removed from the directional bar, remove the wires from the connector as follows: Bend back the connector latches on the sides of the connector slightly to free the secondary lock. Rotate the secondary lock outward on hinge to access terminals in chambers of connector housing. With a paper clip sharpened to a chisel point, insert the paper clip into the connector housing cavity until it stops. Pivot the end of the paper clip and gently tug on the wire to pull the terminal from the cavity. Do not tug on the wire until the tang that holds the terminal in the cavity is released. Take your time, a few tries may be required before you develop a feel for releasing the terminal from the connector. 3. Remove screws that mount turn signals lamps to existing directional bar. Remove lamps and turn signal wires (with their attached connector halves) from existing bar. 4. Position directional bar in mounting location at rear fender and secure bar to motorcycle using original hardware removed in step 2. Route turn signal wires from motorcycle back into directional bar, or up to taillamp (if 1999 and later model) and mate connectors. If the wires were removed from the connector in step 2, insert the terminal ends of the wires into the connector until they snap in place, then mate connector halves.

Harley-Davidson FXWG, FXST (all except FXSTS), FXDWG Light Bar INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2012

download
1. Put a pair of male and female clamp halves together just above the lower triple-clamp. Squeeze the ends of the clamp together with a pair of pliers. Diagram A. 2. Have an assistant position the Light Bar Assembly so the lightbar bracket is to the outside of the clamp assembly. Make sure the wires from the Light Bar Assembly are below the lower triple clamp. Diagram B. 3. Insert a Screw through the clamp and Light Bar Assembly mounting bracket and thread on an Acorn Nut. 4. Hold the Light Bar Assembly in place in front of the lower triple clamp, assemble and attach the remaining clamps. 5. With all four clamp assemblies in place, tighten the clamping screws and nuts to 15 ft. lbs. (21 Nm). Refer to the service manual to gain access to the wire harness inside the fuel tank tunnel or inside the frame backbone. Also, verify the appropriate color wires for hook-up of the passing lamps and turnsignals and running lights. Route the wires from the Light Bar Assembly, around the lower triple- clamp, and up to the frame backbone. Secure the wires so they cannot become pinched when turning the fork. A. The short black wires from the Light Bar Assembly connect to the wires powering the running lights. B. The short red wires from the Light Bar Assembly connect to the wires powering the turnsignals. C. The long blue wires from the Light Bar Assembly connect to the wire powering the headlight low beam. After the wires are connected, verify the operation of the passing lamps, running lights and turnsignals. Correct any connection problems before reassembling the motorcycle. Reinstall the fuel tank. Check all fasteners used during this installation for tightness

HARLEY DAVIDSON SISSY BAR UPRIGHT KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1. Install sissy bar upright kit following the appropriate side- plate instruction sheet. 2. If using sissy bar upright with backrest pad, install pad before applying medallion. 3. Clean surface of sissy bar upright using a 50/50 isopropyl alcohol/water solution. Allow surface to dry thoroughly before continuing. NOTES Test placement of medallion on sissy bar upright before installation. Do not remove adhesive backing until ready to apply. The ideal temperature should be at least 60° F (16° C) for proper adhesion of the medallion on the sissy bar upright. 4. Peel off adhesive backing on bar and shield logo medallion (1) and apply to sissy bar upright (2). Press firmly in place for 10 to 15 seconds. 5. Allow the adhesive to cure for 12 hours at no less than 60° F (16° C). 6. Refer to appropriate sideplate instruction sheet for torque specifications. SERVICE PARTS

Kawasaki VN1600 Highway Bar INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
PREPARATION 1. Insure that the motorcycle is on flat level ground. 2. It is recommended that the motorcycle sit for at least one hour prior to installation to allow the engine to cool. During installation tight all fasteners to hold. Wait until you check all clearances and operation of the brake and shift lever to firmly tighten and torque all fasteners. INSTALLATION Right Side Highway Bar 1. Remove the front floor board bolt (M10). (14mm Socket) Figure 1. Right and Left side of Motorcycle is determined while sitting on the bike.
MAINTENANCE / CAUTION The high quality chrome finish of your National Cycle Chrome Highway Bar can be maintained with any quality chrome cleaner and / or polish applied with a soft cloth. Check hardware for tightness regularly. Never ride with loose mounting hardware. Check to be sure your Highway Bar does not contact any part of the motorcycle at a full turn left and right. Correct any problem before using the motorcycle. ©2005 National Cycle, Inc. PO Box 158, Maywood, IL60153-0158 USA 708-343-0400 / Fax: 708-343-0625 / www.nationalcycle.com / e mail: info@nationalcycle.com Page 2 of 2 10-114857-000 09/05 Install Upper “U” Bolt 2. Place “U” Bolt between the radiator and the down tube at the location shown in Figure 2. Threaded ends of “U” will face out- ward. 3. Select the right side Highway Bar. 4. Loosely install the Highway Bar at the lower mount point using the stock screw. (14mm Socket) Figure 3. While installing the Whizlock Nuts in the following Step #5 , be certain to tighten the nuts evenly, alternating left and right as you tighten. When complete you want the same amount of threads exposed on the ends of the “U” to insure the bolt does not rotate. 5. Install the upper Highway Bar with Whizlock Nuts. (1/2″ Socket) Figure 4. Orient assembly so Whizlock Nuts face outside. Firmly tighten after all clearances are checked. LEFT SIDE INSTALLATION 6. Repeat Steps 1 and 2. On the Left Side due to tight clearances between the radiator and the down tube you must locate the point where the radiator is “notched out” slightly. Figure 5. 7. Select the left side Highway Bar. 8. Repeat Steps 4 and 5.

Incoming search terms: