hard krome exhaust for honda fury

You search Auto repair manual PDF hard krome exhaust for honda fury, if there are search results will appear below. If search results do not exist, please search by others keyword.





2007 Yamaha V-Star 1300 Classic Straights Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Stock Exhaust System Removal 1. Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding pipes at rear mounting bracket. 3. Loosen clamps at mufflers. 4. Remove mufflers. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove rear exhaust pipe assembly. 7. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 8. Remove front exhaust pipe assembly. 9. Remove exhaust-mounting bracket from frame. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install Nut strip into each slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 8. Install Nut strip into each slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks. NOTE: To achieve optimum performance from your Hard-Krome exhaust system we suggest installing the Dynojet jet kit for carbureted models

Incoming search terms:

SUZUKI M109 1800 cc EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 10-11-2010

download
1. Remove the seat and right side fairing cover (with M109 insignia), behind the fuel tank. To remove the fairing, release the plastic peg on top by pushing the center inward and pulling the fairing upwards until the peg releases, remove the M6 button head bolt at the bottom of the fairing. Pull the fairing outward from the rear and upward near the plastic peg to release it. Once it is free from all plastic pegs pull it forward to release it from the bottom of the fuel tank. 2. Remove the right side cover above the exhaust-mounting bracket secured by one M6 button head bolt, retain bolt for later. Remove the chrome steel cover above the exhaust secured by two remaining bolts, (this chrome piece will no longer be used.) Remove the large left rear rubber grommet and flanged steel collar from this chrome piece, to do this press the steel collar out of the rubber grommet first, once the collar is removed push the rubber grommet out of the wire loop on the chrome piece, set aside for later use. 3. Locate the exhaust valve actuator solenoid and harness and disconnect the black 3-prong electrical connector and white 2-prong electrical connector. 4. Remove the socket head bolts securing exhaust flanges to cylinder heads, set these fasteners aside for later use in reassembly. Support the weight of the exhaust system and remove the 2, 8 mm bolts and one 8 mm nut securing the exhaust mounting bracket and exhaust assembly. Keep these fasteners for use later. Remove the stock exhaust system as one complete unit; this includes the stock exhaust bracket, headpipes and muffler, exhaust valve solenoid and cables. 5. The exhaust valve actuator solenoid must now be removed from the stock exhaust-mounting bracket. To perform this, loosen the two nuts securing each cable to the exhaust valve cable-mounting tab, Position A in Figure 1. Make enough slack in the cables so that the ends of the cables’ threaded sheath may be disengaged from the end of the mounting tab. Now remove the two M6 hex head bolts securing the solenoid to the stock exhaust bracket. The stock exhaust mounting bracket, headpipes and muffler and exhaust valve solenoid cables will not be used anymore with the your new Cobra Exhaust System. 6. Remove the dust cover from the solenoid to expose the rotating cam and cables. DO NOT TRY TO ROTATE THE CAM RELATIVE TO THE ACTUATOR SELENOID TO REMOVE THE CABLES; DOING SO MAY DAMAGE THE INTERNAL COMPONENTS OF THE SOLENOID. To remove the cables from the cam, use the slack in the cables obtained in Step 5 to disengage the cable barrels from the cam, see Figure 1. THE DUST COVER WILL NOT BE REINSTALLED. 7. Now prepare the exhaust valve actuator solenoid for reuse. SECURELY HOLD THE CAM TO PREVENT IT FROM ROTATING IN THE SOLENOID. WHILE PREVENTING THE CAM FROM ROTATING, remove the 10 – 32 flange bolt securing it, see Figure 2. Replace the cam with the Cobra supplied cam, BE SURE TO PREVENT THE CAM FROM ROTATING WHEN REINSTALLING THE BOLT, OTHERWISE DAMAGE MAY OCCUR TO THE SOLENOID , see Figure 3. Torque to factory specifications.

Incoming search terms:

SUZUKI M109 1800 cc FRONT/REAR EXHAUST / HEATSHIELD INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 15-11-2010

download
1. Remove the seat and right side fairing cover (with M109 insignia), behind the fuel tank. To remove the fairing, release the plastic peg on top by pushing the center inward and pulling the fairing upwards until the peg releases, remove the M6 button head bolt at the bottom of the fairing. Pull the fairing outward from the rear and upward near the plastic peg to release it. Once it is free from all plastic pegs pull it forward to release it from the bottom of the fuel tank. 2. Remove the right side cover above the exhaust-mounting bracket secured by one M6 button head bolt, retain bolt for later. Remove the chrome steel cover above the exhaust secured by two remaining bolts, (this chrome piece will no longer be used.) Remove the large left rear rubber grommet and flanged steel collar from this chrome piece, to do this press the steel collar out of the rubber grommet first, once the collar is removed push the rubber grommet out of the wire loop on the chrome piece, set collar and grommet aside for later use. 3. Locate the exhaust valve actuator solenoid and harness and disconnect the black 3-prong electrical connector and white 2-prong electrical connector. 4. Remove the socket head bolts securing exhaust flanges to cylinder heads, set these fasteners aside for later use in reassembly. Support the weight of the exhaust system and remove the 2, 8 mm bolts and one 8 mm nut securing the exhaust mounting bracket and exhaust assembly. Keep these fasteners for use later. Remove the stock exhaust system as one complete unit; this includes the stock exhaust bracket, headpipes and muffler, exhaust valve actuator solenoid and cables. 5. The exhaust valve actuator solenoid must now be removed from the stock exhaust-mounting bracket. To perform this, loosen the two nuts securing each cable to the exhaust valve cable-mounting tab, Position A in Figure 1. Make enough slack in the cables so that the ends of the cables’ threaded sheath may be disengaged from the end of the mounting tab. Now remove the two M6 hex head bolts securing the solenoid to the stock exhaust bracket. The stock exhaust mounting bracket, headpipes and muffler and exhaust valve solenoid cables will not be used anymore with the your new Cobra Exhaust System

Harley davidson American Classic Straights on a 1988-2001 VLX 600 Shadow Installation Instructions

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding pipes at rear mounting bracket. 3. Loosen clamps at mufflers. 4. Remove mufflers. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove rear exhaust pipe assembly. 7. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 8. Remove front exhaust pipe assembly. 9. Remove exhaust-mounting bracket from frame. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system.
1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install nut strip into slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the rear cylinder head — DO NOT TIGHTEN NUTS! 8. Install nut strip into slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks.

Incoming search terms:

HONDA VTX1800R & HONDA VTX1800N BIG SHOTS EXHAUST SYSTEM

0

Filed Under (Honda) by admin on 10-11-2011

download
harness. Remove wire tie (take note of harness routing for reassembly). Un-route wires and drape over right side of pipe. 3. Remove entire right side floorboard assembly, (three bolts) (Figure 1). 4. Remove exhaust port flange nuts.
5. Remove flange bolts securing rear muffler mount to exhaust system mounting bar. 6. Remove complete exhaust system. Start by removing front head pipe from exhaust port (assistance may be required). 7. Remove rectifier from mounting bar. 8. Remove stock (cast iron) exhaust system mounting bar.

HONDA FURY FRONT HEADPIPE W/HEATSHIELD, REAR HEADPIPE / MUFFLER W/HEATSHIELD INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 15-11-2010

download
Remove your stock exhaust system and stock exhaust mount. Save the (4) acorn nuts that attach the headpipes to the cylinders for later use during installation. 2. Install exhaust mounting bracket onto outside of frame, where stock mounting bolts were removed, by inserting the supplied M10 x 70 mm bolt into the top mounting hole and the shorter M10 x 45 mm into the lower and thru the frame, see Figure 1. Start threading the supplied M10 Nylock nut onto lower and upper bolts but DO NOT FULLY TIGHTEN. 3. Loosen the right footpeg/floorboard assembly to help provide installation clearance for the front headpipe. 4. Slide the supplied exhaust flange over the front headpipe and bolt to cylinder using stock hardware from Step 1. DO NOT TIGHTEN at this time. 5. Place the supplied 27-61msc clamp onto the lower muffler slip collar then slide the rear headpipe / muffler assembly onto the front headpipe and into the rear exhaust port. Bolt rear headpipe to the rear cylinder using the stock acorn nuts from Step 1. See Figure 2 for clamp orientation. 6. Bolt the muffler assembly to the mounting bracket using the supplied 5/16 bolts. DO NOT TIGHTEN . 7. Make sure the front headpipe is inserted properly into the rear assembly and make sure the pipes are parallel with each other. Fully tighten the exhaust bracket to the frame first, then the front and rear cylinder acorn nuts attaching the exhaust flanges, then the muffler to the exhaust bracket. Then tighten the 27-61msc clamp last. (NOTE: If the muffler clamp is slid past the slots on the slip collar the clamp will not tighten properly.) 8. Unscrew the remaining hose clamps and feed the tail end of the clamp through the clips on the inside of the heatshields, the larger clamps go to the rear of the heatshields where they will rest on the muffler bodies, smaller ones to the front for the headpipes. The screw end of the hose clamp should be accessible for tightening but not visible when heatshields are mounted to the pipes, see Figure 3. 9. To install the front heatshield, first slide the rear portion of the heatshield over the muffler, continue to slowly slide it forward pushing the front of the shield gently into place between the frame and motor (Hint: Spread the hose clamps apart slightly to make it easier to slide them over the muffler assembly and headpipes). Make sure the muffler clamp doesn’t interfere with the heatshields and is aligned as shown in Figure 2. Snug the heatshield clamps but DO NOT TIGHTEN . 10. Install the rear heatshield in the same manor as the front heatshield. Tighten all hose clamps.

Incoming search terms:

1999-2007 Yamaha V Star 1100 3" Res-Tec Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Stock Exhaust System Removal 1. Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove O2 sensors from each muffler and cover with supplied cap plug. 3. Loosen clamps at mufflers. 4. Remove bolts that are holding mufflers at rear mounting bracket. 5. Remove mufflers. 6. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 7. Remove rear pipe assembly. 8. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 9. Remove front pipe assembly. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install 3/8-16 Square nut into each slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 8. Install 3/8-16 Square nut into each slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks

Incoming search terms:

HONDA VTX1800R AND HONDA VTX1800N BIG SHOTS EXHAUST SYSTEM REMOVAL

0

Filed Under (Honda) by admin on 17-11-2011

download
If motorcycle is oxygen sensor equipped, unscrew the sensors from the stock exhaust system and install them
into the Vance & Hines exhaust system, being sure to install the front cylinder sensor into the lower pipe and
the rear cylinder sensor into the top pipe. Note: Use caution when handling. Do not touch sensor tip area.
2. If motorcycle is not oxygen sensor equipped, install both M12 x 11 plugs and washers (supplied)into the oxygen
sensor bosses. 3. Check condition of stock exhaust gaskets. Replace if damaged or worn. 4. Install and tighten supplied mounting bracket (stamped 345-P) in the original mounting bar location, using one M10 x 35 flange bolt and nut on top (supplied) and one M10 x 20 flange bolt on bottom (supplied) (Figure 2). Note: The bracket mounts behind the top frame mount and in front of the bottom frame mount(Figure 2).5. Install and tighten rectifier using M6x30 flange bolt, nut
and washer combinations (supplied) (Figure 2). 6. Place heat shields on a non-abrasive surface such as a blanket or carpet. Using a felt tip marker mark outside surface of front and rear heat shields with location of the mounting clips welded to the inside

Incoming search terms:

BMW K1200 RS/ GT Full Exhaust System Full Exhaust System Installation Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the side- stand or ideally a rear service stand. 2. Remove the lower fairing. 3. Unscrew the O 2 sensor. Remove the stock exhaust system at the rear canister support bracket and where it bolts to the engine. CAUTION -the stock exhaust is very heavy, be careful not to drop it! Also, be careful not to damage the engine sensor located near the front header pipe. 4. Pry out the old exhaust port gaskets and replace with new BMW OE (x4) exhaust port gaskets. Adab of grease will help hold the gaskets in place while you work. 5. Coat the exhaust studs and O 2 sensor threads with high temperature anti-seize compound. 6. Install the TBR headers into the exhaust ports making sure to get a good seat onto the exhaust port gaskets. Next, install the header nuts starting at the rear/outside stud and working your way forward on the outside set of studs. Once that is finished repeat along the inside set of studs. Tighten header nuts only finger tight at this point. 7. Be sure to coat the threads of the sensor with the included packet of hi-temp anti-seize. Install the O 2 sensor into the TBR headers. Turning the sensor in the counterclockwise direction a few times then screwing it clockwise to install will help make it easier to install and prevent the wire from binding. 8. Place a bead of the hi-temp sealant on the outside edge of the headers that goes into the canister. Slide the TBR canister onto the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out. 9. Carefully slide the muffler clamp over the muffler. ( Note: The stainless steel canister clamp and the name badge on the canister come from the factory with a clear plastic protective film. Please remove this film before operation.) Attach it to the canister support bracket using the stock BMWhardware. Both tabs of the canister clamp should be located on the inside of the canister support bracket. Leave loose for the moment. 10. Make sure everything is lined up and start to evenly tighten up the header nuts to BMWfactory torque specification. Tighten the canister support hardware and install the springs as well. 11. Start the bike and check for leaks around the exhaust ports and the header/canister junction. 12. Reinstall the lower fairing

Incoming search terms:

2002 Honda VTX 1800 R & S 3” BIG Straights Installation Instructions

0

Filed Under (Honda) by admin on 17-11-2011

download
Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove O2 sensors from each muffler and cover with supplied cap plug. 3. Loosen clamps at mufflers. 4. Remove bolts that are holding mufflers at rear mounting bracket. 5. Remove mufflers. 6. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 7. Remove rear pipe assembly. 8. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 9. Remove front pipe assembly. Hard-Krome Exhaust System Installation
NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to
replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design,
configuration and location. WARNING: Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessaryon a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed

Incoming search terms: