harley 4a connector

You search Auto repair manual PDF harley 4a connector, if there are search results will appear below. If search results do not exist, please search by others keyword.



  harley 4a connector Direct Download speed 5282 Kb/s

  harley 4a connector Full Version speed 6162 Kb/s



BMW R259 Installation Instructions Fuel Control For BMWOilheads

0

Filed Under (BMW) by admin on 12-11-2010

download
Installation R1200 C -Removethechrome right air filter cover. Release the brake fluid reservoir from its mount. Follow the oxygen sensor lead from the exhaust to the connector. It is mounted to the back of the brake fluid reservoir mounting bracket with cable ties. Cut the cable ties to release the connector from the bracket. Gently pull the connector apart. Insert the male O2 connector from the R259 into the oxygen sensor lead. Connect the female side of the R259sO2 connector to the bike’swiringharness side. Make sure both sets of connectors are fully seated. Cable tie the sensor lead connector back to the bracket and tuck the other O2 connector under the front of theairhorn. -Depressthe retaining bail on the right fuel injector connector and gently pull off the connector. Install this connector on the male R259 injector lead. Install the remaining R259 connector on the right injector. -Connecttheground lead by removing the allen screw (5mmhex) that secures theairboxtothe frame. Place the screw through the lug on the ground lead and reinstall and tighten the screw. Go to section 3 and verify power-up. Tuck the wiring below and behind theairhornand cable tie as necessary. Using the supplied velcro, attach the controller box to the top of theairhorn. Reinstall the brake fluid reservoir in its mount and reinstall the side-cover. Seethe Techlusionwebsite for more detail. Installation R850, R1100, R1150, R1100S -Refertothe appropriate BMW service guides and remove the fuel tank. On some models it maybe possible to have an assistant lift the tank up and to the left to expose the oxygen sensor connector, without fully disconnecting the tank. Locate the oxygen sensor connector by following the lead from the exhaust system. It will be cable tied to the right frame backbone. Cut the retaining cable ties and pull the connector away from the frame. Open the connector and insert the male R259 O2 connector into the oxygen sensor lead, and the female to the bike’swiringharness. Cable tie these back to the right frame backbone. -Routethe R259 wiring harness down the right frame, in-between the battery tray and the rear fuel tank mount. Using the supplied velcro attach the R259 to theairboxlid. Locate the lead on the right fuel injector, and while depressing the locking bail on the connector, gently pull the leadoff. Install this lead on the R259 male injector connector; install the remaining connector on R259 harness to the right injector. Make sure all of the connectors are fully seated. Cable tie any excess wiring away from the fuel lines and throttle mechanism. -Connecttheground lead to the battery negative terminal or an alternate good ground. -Re-install the fuel tank. Make sure the fuel lines are connected and their routing is correct. Insure that both throttle cables are correctly seated in their adjusters on the throttle bodies, and that nothing interferes with the throttle mechanisms on either throttle body. Turn the key on and allow the fuel system to pressurize. CHECK FOR ANY FUEL LEAKS and repair as necessary. Go to section 3 to verify power-up. Re-install any other bodywork removed. Seethe Techlusionwebsite for more detail.

Incoming search terms:

Installation Instructions Fuel Control For BMW Oil heads

0

Filed Under (BMW) by admin on 26-10-2010

download
Removethechrome right air filter cover. Release the brake fluid reservoir from its mount. Follow the oxygen sensor lead from the exhaust to the connector. It is mounted to the back of the brake fluid reservoir mounting bracket with cable ties. Cut the cable ties to release the connector from the bracket. Gently pull the connector apart. Insert the male O2 connector from the R259 into the oxygen sensor lead. Connect the female side of the R259sO2 connector to the bike’swiringharness side. Make sure both sets of connectors are fully seated. Cable tie the sensor lead connector back to the bracket and tuck the other O2 connector under the front of theairhorn. -Depressthe retaining bail on the right fuel injector connector and gently pull off the connector. Install this connector on the male R259 injector lead. Install the remaining R259 connector on the right injector. -Connecttheground lead by removing the allen screw (5mmhex) that secures theairboxtothe frame. Place the screw through the lug on the ground lead and reinstall and tighten the screw. Go to section 3 and verify power-up. Tuck the wiring below and behind theairhornand cable tie as necessary. Using the supplied velcro, attach the controller box to the top of theairhorn. Reinstall the brake fluid reservoir in its mount and reinstall the side-cover. Seethe Techlusionwebsite for more detail. Installation R850, R1100, R1150, R1100S -Refertothe appropriate BMW service guides and remove the fuel tank. On some models it maybe possible to have an assistant lift the tank up and to the left to expose the oxygen sensor connector, without fully disconnecting the tank. Locate the oxygen sensor connector by following the lead from the exhaust system. It will be cable tied to the right frame backbone. Cut the retaining cable ties and pull the connector away from the frame. Open the connector and insert the male R259 O2 connector into the oxygen sensor lead, and the female to the bike’swiringharness. Cable tie these back to the right frame backbone. -Routethe R259 wiring harness down the right frame, in-between the battery tray and the rear fuel tank mount. Using the supplied velcro attach the R259 to theairboxlid. Locate the lead on the right fuel injector, and while depressing the locking bail on the connector, gently pull the leadoff. Install this lead on the R259 male injector connector; install the remaining connector on R259 harness to the right injector. Make sure all of the connectors are fully seated. Cable tie any excess wiring away from the fuel lines and throttle mechanism. -Connecttheground lead to the battery negative terminal or an alternate good ground

Incoming search terms:

HARLEY DAVIDSON V-ROD Fi2000 Fuel Injection Module Installation Manual

0

Filed Under (Harley Davidson) by admin on 15-11-2010

download
1. Flip up seat, to gain access to radiator reservoir area. 2. Remove Dzus fastener to remove simulated fuel tank cover, over airbox housing. Depending on which model V-Rod is being worked on, the front shrouds covering the upper front frame section may also need to be removed. 3. Place Fi2000 in under-seat area, run fuel injector connector harness up right side frame rail between top right frame rail, and radiator overflow tank, see Figure 1. At the rear of the airbox, route the harness below the airbox, and downward next to the inner radiator hose. Unplug both stock fuel injector connectors, on the front and rear injectors between the engine cylinders, see Figure 2. These are disconnected, by depressing the metal springs that are on the end of each female connector. The stock female connectors are marked “F” and “R”, noting which connector goes to the front and rear injector, be sure to pay attention to this. Now connect the longer male Fi2000 connector to the front female H.D. connector. Plug shorter Fi2000 male connector into the stock rear female H.D. connector. Then plug the longer female Cobra connector onto the front stock H.D. injector. Plug the shorter Fi2000 female connector onto the rear injector. Each injector connector pair should rest underneath each respective injector. 4. It is now time to install the oxygen sensor eliminator modules. This product is designed to eliminate the “check engine” light from coming on when the stock oxygen sensors are disconnected on Harley Davidson Motorcycles utilizing fuel injection. The motorcycle has a full “open loop” fuel injection map written in its ECU and the motorcycle reverts to this default map after the oxygen sensors have been removed or just disconnected. 5. Locate the rear oxygen sensor and follow the harness up to the under-seat area behind the radiator overflow tank. Pull the stock connectors up from below the overflow tank and disconnect, see Figure 1. Plug one of the supplied Oxygen sensor eliminators on to the stock male connector. Tuck the connectors back underneath the bracket behind the radiator overflow tank. 6. Now locate the front oxygen sensor on the front headpipe, and trace the oxygen sensor harness back to the connectors tucked between the left front frame rail and plastic radiator shroud, see Figure 3. Pull these connectors out, and disconnect them. Plug the remaining supplied oxygen sensor eliminator on to the stock male connector. Tuck the connectors back in between the frame rail and plastic shroud

Incoming search terms:

HARLEY DAVIDSON NARROW CHROME DIRECTIONAL BAR INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
This kit is designed for installation on 1986 and later FLST®, FLSTC®, FLSTN®and 1991 and later Touring models. (Except 2004 and later FLHRS®and FLTR®) NOTE: Will not fit when equipped with Flat Lens Turn Signal Module (Part Number 91699-99A). Installation 1. Disconnect turn signal wires. For 1999 and later models: See Figure 1. Remove taillight cover and disconnect turn signal wires at connectors shown in illustration. For 1998 and earlier models: Disconnect turn signal wires at connectors located in directional bar. On 1994 and later models there are two wires for each turn signal lamp. Earlier models have only 1 wire per lamp. 2. Remove existing directional bar from motorcycle and save hardware for re-installation. If the turn signal connector is too large to be removed from the directional bar, remove the wires from the connector as follows: Bend back the connector latches on the sides of the connector slightly to free the secondary lock. Rotate the secondary lock outward on hinge to access terminals in chambers of connector housing. With a paper clip sharpened to a chisel point, insert the paper clip into the connector housing cavity until it stops. Pivot the end of the paper clip and gently tug on the wire to pull the terminal from the cavity. Do not tug on the wire until the tang that holds the terminal in the cavity is released. Take your time, a few tries may be required before you develop a feel for releasing the terminal from the connector. 3. Remove screws that mount turn signals lamps to existing directional bar. Remove lamps and turn signal wires (with their attached connector halves) from existing bar. 4. Position directional bar in mounting location at rear fender and secure bar to motorcycle using original hardware removed in step 2. Route turn signal wires from motorcycle back into directional bar, or up to taillamp (if 1999 and later model) and mate connectors. If the wires were removed from the connector in step 2, insert the terminal ends of the wires into the connector until they snap in place, then mate connector halves.

Harley-Davidson Softail, Touring, Dyna, Sportster and V-Rod, SELF LEARNING MODULE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2012

download
STEP 1 – BATTERY CONNECTION Locate the battery and disconnect the negative battery cable. Mount the module in the open area in front of the battery with 2-tie straps or velcro straps, directing the harness from the module towards the 6 o’clock position. STEP 2 – THROTTLE POSITION SENSOR (TPS): Remove the air cleaner assembly and unplug the TPS sensor connector at the TPS sensor. The harness includes (2) TPS connectors which should be routed under the gas tank into the factory wire loom to the TPS sensor. The TPS sensor is located on the left side of the throttle body. Plug the (2) TPS connectors from the module in between the TPS sensor and to the factory TPS connector. STEP 3 – O2 SENSOR: Systems equipped with factory O2 sensors Rear: Unplug the Rear O2 sensor connector from the factory harness, which is located at the Rear exhaust pipe. Route the module’s harness which includes (2) O2 sensor connectors and connect one connector to the Rear O2 sensor and connect the other connector to the main factory O2 sensor connector. Front: Unplug the Front O2 sensor connector from the factory harness, which is located at the Front exhaust pipe. Route the module’s harness which includes (2) O2 sensor connectors, and connect one connector to the Front O2 sensor and connect the other connector to the main factory O2 sensor connector. Systems not equipped with factory O2 sensors NOTE: Many aftermarket exhaust systems are now equipped with plugged O2 sensor bungs which can be removed to accept an aftermarket O2 sensor. Typically these bungs already have a thread size of 18 mm x 1.5 mm. Exhaust systems not equipped with O2 sensor bungs need to have the supplied 18 mm x 1.5 mm thread size bung welded to the exhaust pipe in order to install an O2 sensor. The O2 sensor bung should be installed 3 to 6 inches away from the rear cylinder exhaust port and in front of the exhaust torque tube pipe area. The module prefers to receive information from the O2 sensor from an area that is NOT contaminated from atmospheric air. This air may enter through the tail pipe of an unrestricted or un-baffled exhaust pipe. The bung should not be installed in the “5 to 7 o’clock” area. If mounted in this area the O2 sensor can be damaged. The moisture from the gases exiting from the rear cylinder exhaust port will harm the ceramic shell element of the O2 sensor.

Incoming search terms:

Ignition Upgrade Module for 2004-up Carbureted Harley Davidson Motorcycles Owner's Manual

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
1. Disconnect the negative battery cable. 2. Grasp the sides of the electrical caddy (located next the ignition coil) and pull outward to remove. 3. Remove the relay and fuse panels from the electrical caddy. a. Insert a small screwdriver into the slot under each fuse and relay panel. b. Using a screwdriver, disengage the panel from the electrical caddy. 4. Disconnect the main fuse connector from the electrical caddy a. Remove the main fuse from the connector b. Insert small screwdrivers into the slots on each side of the main fuse c. Depress the tabs of the main fuse connector to disengage it from the electrical caddy
Thunder Heart Performance Corp. 615-672-8811 www.thunder-heart.com 2 EI5075.doc 5. Depress the tab located on the electrical caddy securing the TSM/TSSM. Pull it from the electrical caddy. Disconnect the TSM/TSSM connector. 6. Slide the data link connector towards the front of the motorcycle to disengage it from the electrical caddy. 7. Disconnect the ignition control module connector. 8. Disconnect the ignition coil connector and spark plug cables from the coil. 9. Remove the electrical caddy fasteners (3 total). 10. Remove the wiring from the electrical caddy. 11. Remove the fasteners securing the factory ignition control module from the electrical caddy. 12. Installation of the Digital Ignition Module is the reverse of removal. 2.2 Touring Models 1. Disconnect the negative battery cable. 2. Remove the right saddlebag. 3. Gently pull the side cover from the frame downtubes (no tools required). 4. Depress the external latches and use a rocking motion to remove the electrical connector from the ignition control module. 5. Remove the two socket screws to detach the ignition control module from the electrical bracket. 6. To install the Digital Ignition Module, install and tighten the socket screws to 50-60 in-lbs . The remainder of installation is the reverse of removal. 2.3 Softail Models 1. Remove the seat. 2. Disconnect the negative battery cable. 3. Remove the two screws to free the ignition control module from the mounting bracket. 4. Depress the external latches and use a rocking motion to remove the electrical connector from the ignition control module. 5. To install the Digital Ignition Module, install and tighten the socket screws to 15-21 in-lbs . The remainder of installation is the reverse of removal

Incoming search terms:

HARLEY DAVIDSON SOFTAIL FRONT SPOILER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 2 and Table 1. INSTALLATION 1. Position the vehicle on a motorcycle lift table. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 3. Raise the vehicle on the lift table to allow access to the lower front portion of the frame. 2008+ 2007 7 8 11 3 3 4 4 12 5 5 1 1 9 2 2 10 6 6 9 9 11 13 is02652c 8. 1. Two-pin voltage regulator connector (2007 only) Voltage regulator 2. 9. Voltage regulator attaching screws (2) Cable strap (2 for 2007, 1 for 2008 and later) 10. 3. Lower voltage regulator cover (2007 only) Voltage regulator bracket 4. 11. Bracket screw to engine crankcase (2) Oxygen sensor connector 12. 5. Crank position sensor connector (2007 only) Voltage regulator caddy 6. 13. Voltage regulator caddy cover Horn connectors (some 2008 and later models) 7. Four-pin voltage regulator connector (2007 only) Figure 1. Original Equipment Voltage Regulator  NOTE For 2007 models: The ground wire on the voltage regulator must be re-attached at the original location when re-installing the voltage regulator to ensure adequate ground. 4. For ALL models: See Figure 1. Remove and discard the voltage regulator caddy cover (6) from the regulator bracket (3) and caddy (5). For 2007 models: In addition, remove the lower voltage regulator cover (10). 5. Remove and retain the hex socket head screw (4) at the top left of the bracket For 2007 models: In addition, disconnect the ground wire. Free the cable straps (9) from the regulator bracket, beneath the regulator. 6. Remove the two hex socket head screws with washers (2) retaining the voltage regulator to the bracket. Remove and save the regulator, but discard the screws. 7. Remove and retain the screw (4) at the top right of the regulator bracket. Remove the bracket from the engine. 8. For 2008 and later models: Free the strap (9) that ties the jiffy stand wiring to the voltage regulator bracket. Unfasten the three-way jiffy stand sensor connector and the two-way crank position sensor connector [79] (12) from the T-studs on the back of the regulator bracket (3). Discard the bracket. Disconnect both plugs from the back of the voltage regulator (1). For 2007 models: Unfasten the four-way (7) and two-way (8) voltage regulator connectors from the T-studs on the back of the regulator bracket (3), and discard the bracket. Disconnect the voltage regulator (1) at both connectors. 9. For 2008 and later models: Unclip the two-way O 2 (oxygen) sensor electrical connector [138] (11) from the voltage regulator caddy (5). For 2007 models: Unfasten the two-way crank position sensor connector [79] (12) from the voltage regulator caddy (5). Remove the caddy from the vehicle frame. a. For 2007 models: Unclamp the bottom of the caddy from the engine mount spacers. b. For ALL models: Unhook the top clips from around the tabs on the front of the engine casting. Remove the original equipment (O.E.) caddy from the vehicle frame, and discard it.

Incoming search terms:

2007-2010 Harley Davidson Dyna EFI Tuner INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2012

download
Remove the seat 2 Remove the left hand side cover (Fig. A). 3 Unplug the stock wiring harness connector from the ECM (Fig. B). 4 Move the data plug (Fig. B) out of the way to access bolt. 5 Remove the 3 bolts that hold the electrical box in place (Fig. B). 6 Slide the plastic box out from the frame. 7 Route the stock connector through to the back side of the electrical box (Fig. C). Fig. A Fig. B Fig. C Remove side cover Stock connector Stock connector Dat a plug Remove bolt Remove bolt s FM814 www .fuelmotousa .com 2007-20 1 0 Harley Davidson Dyna – FM EFI Tuner – 2 8 Lay the PCIII behind the electrical box temporarily. 9 Route the GREYconnector from the PCIII through the back of the electrical box and plug it into the ECM (Fig. D). 10 Connect the stock wiring harness to the BLACK connector of the PCIII. 11 Zip tie these connectors to the front side of the electrical box (Fig E). Make sure they are situated away from the rear exhaust pipe. Fig. D Fig. E PCIII connector Stock connector PCIII connector 12 Mount the PCIII to the underside of the stock ECM (Fig. F) using the supplied velcro. Make sure to clean both surfaces with the alcohol swab before attaching. Situate the PCIII so the USB and expansion ports point to the rear of the bike. This will allow you easier access to adjust the maps if necessary

Incoming search terms:

HARLEY DAVIDSON SECURITY SYSTEM SMART SIREN KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
REMOVAL 1. Refer to the owner’s manual and follow the instructions to disarm the security system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. For All Models except 2002-2003 Touring and 2003- Later Softail: Refer to the owner’s manual and follow the instructions to disconnect the battery, negative (-) cable first or remove the main fuse. For 2002-2003 Touring and 2003-Later Softail Models: Remove seat following the instructions in the service manual and disconnect the battery, negative (-) cable first. Save seat hardware for installation. INSTALLATION 2002-2006 VRSCA, VRSCB, VRSCD Models 1. Open the seat. 2. See Figure 1. Remove the splash guard (mud flap) nuts. 3. See Figure 2. Lower the mud flap from the installed position and allow it to rest on the rear tire 3. Slide the siren into place on the left side of the electrical caddy so the sounder disc (6) faces out. 4. Refer to the owner’s manual and follow the instructions to install the main fuse. 5. Align the barbed studs on the side cover with the grommets in the frame and push side cover firmly into place. 6. Install the left side saddlebag per the instructions in the owner’s manual. 2003 and later Softail Models EXCEPT FXCW/C 1. Remove the right side saddlebag (if equipped) per the instructions in the owner’s manual. NOTE The siren connector is installed on an electrical panel under the rear fender on all Softail models. The rear of the motorcycle may have to be raised slightly to allow removal of the splash guard. 2. Remove the two bolts at the bottom of the splash guard. Bend the upper right corner of the splash guard toward the rear tire and lift upward to unhook the splash guard from the tab on the rear fork. Remove the guard from beneath the fender. 2 1 3 is01316 1. Siren mounting area 2. Siren connector [142B] 3. Harness clip Figure 16. Siren Connector (Softail Models EXCEPT FXCW/C) (Rear Fender View with Rear Wheel Removed) 3. See Figure 16. Remove the siren connector [142B] (2) from the receptacle in the siren mounting area (1) of the electrical panel. 4. See Figure 17. Insert security siren (1) connector [142B] into the siren box receptacle until the connector latches securely. 5. Orient the siren (1) as shown, with the harness connector (2) toward the bottom and the sounder disc (5) facing out. Carefully snap the siren into the electrical panel. 6. Insert the siren harness lead (4) into the harness clip (3) to keep the harness clear of other components. 7. If necessary, secure the connector wiring to the electrical panel wiring with a cable strap (not provided). 8. Hook the slot at the top of the splash guard over the tab on the rear fork and install the guard with the two screws removed earlier. Tighten securely. 9. Install the right side saddlebag (if equipped) per the instructions in the owner’s manual. 10. Refer to the owner’s manual and follow the instructions given to connect the battery cables or install the main fuse

Incoming search terms:

2004-2005 Harley Davidson Dyna EFI Tuner Installation Manual

0

Filed Under (Harley Davidson) by admin on 14-04-2012

download
1 Remove the seat 2 Remove the left hand side cover (Fig. A). 3 Unplug the stock wiring harness connector from the ECM (Fig. B). 4 Move the data plug (Fig. B) out of the way to access bolt. 5 Remove the 3 bolts that hold the electrical box in place (Fig. B). 6 Slide the plastic box out from the frame. 7 Route the stock connector through the box and into the small opening in the frame (Fig. C). Fig. A Fig. B Fig. C Remove side cover Stock connector Stock connector Data plug Remove bolt Remove bolts FM810 www. fuelmotousa.com 2004-2005 Harley Davidson Dyna – FM EFI Tuner – 2 8 Plug the black connector of the Power Commander into the stock wiring harness connector (Fig. D). 9 Route the grey connector of the Power Commander through the box and plug it into the ECM. 10 Install the Power Commander against the rear part of the electrical box. Make sure to clean both surfaces with the alcohol swab first. Use the supplied velcro to attach the Power Commander. 11 Bolt the box back into place. 12 Reinstall the seat. Fig. D Fig.

Incoming search terms: