harley bolt grade foot pegs

You search Auto repair manual PDF harley bolt grade foot pegs, if there are search results will appear below. If search results do not exist, please search by others keyword.



  harley bolt grade foot pegs Direct Download speed 5282 Kb/s

  harley bolt grade foot pegs Full Version speed 6162 Kb/s



1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

HARLEY DAVIDSON Softail Big Shots Staggered Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 20-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. If equipped, loosen the floor boards to gain clearance for exhaust removal and installation. 2. Loosen heat shield clamps on both the front and rear head pipes. 3. If equipped, loosen crossover pipe clamp, located between front and rear head pipes. 4. Remove two cylinder exhaust port flange nuts from each head pipe, located at the cylinder head. 5. Remove the bolts that attach mufflers to the frame. 6. Remove the complete exhaust system and set aside. Assistance may be required. 7. Remove stock mounting bars and brackets. 8. On models equipped with upper mounting bar attached at swing arm pivot bolt, go to step 9. If upper mounting bar is attached with two torx bolts (not swing arm bolt) go to step 10. 9. Remove right side 1/4″-20 bolt which holds lower fender in place. The fender will flex outwards allowing removal of right passenger foot peg bolt. Park the motorcycle on its side stand. Position a floor jack under right hand frame tube of the motorcycle below swing arm pivot bolt. Raise jack just enough to take the weight off swing arm pivot bolt. Remove swing arm pivot bolt and stock upper mounting bar. Replace swing arm pivot bolt and torque to 120 ft. lbs. Reinstall passenger foot peg using 1/2″-20 x 3″ bolt and 1 5/8″ long spacer (supplied). Reinstall 1/4″-20 fender bolt. 10. Using a T50 torx driver, remove the three mounting bolts and mounting bar. (Two of the bolts are visible, the third also attaches right hand passenger foot peg pivot and is accessed by removing foot peg. Reinstall foot peg using 3/8″x 2-1/2″ Allen bolt and 3/4″ long spacer (supplied). 11. Carefully remove exhaust port flanges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check exhaust port gasket condition. (Recommended replacement exhaust port gaskets, Harley part number:17048-98 or 65324-83A)

Incoming search terms:

Harley Davidson Softail Sideshots Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 20-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. On FLSTN, FLSTF, FLSTH and FLSTC loosen the right hand floor board mounting bolts to gain clearance for exhaust removal and installation. 2. Loosen the heat shield clamps on both front and rear exhaust pipes. 3. Loosen the crossover pipe clamp, located between the front and rear head pipe. (Not necessary on 2000- up models). 4. Remove the two mounting nuts from each head pipe, located at the cylinder head 5. Remove the bolts attaching the mufflers to the frame. 6. Remove the entire exhaust system and set it aside. 7. On pre 2000 models remove the lower mounting bar. 8. FLSTN, FLSTF and FXSTD models have an upper mounting bar that must be removed in addition to the lower bar. On pre 2000 models go to step #9, on 2000-up models go to step #10. 9. Remove the right passenger foot peg bolt. Position the motorcycle on the side stand with a floor jack under the swing arm pivot bolt on the right hand side. Raise the jack just enough to take the weight off the pivot bolt, remove the bolt and stock mounting bar. Reinstall the pivot bolt and torque to 120 -150 ft. lbs. Reinstall the passenger foot peg using the 1/2″ x 3″ Allen bolt and 1-5/8″ length spacer (supplied). 10. Using a #50 Torx driver, remove the three mounting bolts, and set the mounting bar aside. (Two of the bolts are visible, the third is accessed by removing the right hand passenger foot peg.) Replace the foot peg using the 3/8″ x 2 1/2″ Allen bolt and 3/4″ length spacer (supplied). 11. The bolts and spacers used in the above steps may also be used on all Softail models to space the right rear foot peg away from the exhaust. 12. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers (save for reuse). NOTE: If circlips look bent or twisted replace them with new circlips.

HARLEY DAVIDSON SOFTAIL 2 into 1 Pro Pipe Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Loosen the crossover pipe clamp, located between the front and rear head pipes. 3. Remove the two mounting nuts from each head pipe, located at the cylinder head. 4. Remove the two nuts from the back side of each muffler. 5. Remove the entire exhaust system and set it aside. 6. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them. 7. Remove the two bolts that hold the front muffler mounting bar to the frame. Note: FLSTN, FLSTF models require the removal of the stock exhaust system mounting bar. For removal: Remove the right passenger foot peg bolt. Position the motorcycle on it’s side stand with a floor jack under the swing arm pivot bolt on the right hand side. Raise the jack just enough to take the weight off the pivot bolt and remove the bolt and stock mounting bar. Replace the pivot bolt and torque it between 120 -150 ft. lbs. 8. Reinstall the foot peg bolt using the 1/2″ x 3″ bolt and spacer tube (both supplied). Tighten the bolt making sure the foot peg folds in the proper direction. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM Note: For easier installation on models with floorboards, it will be necessary to loosen the right side floorboard. 1. Check the stock exhaust gaskets to be sure they’re in good shape. If you have any doubts as to their condition, replace them. 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of each heat shield. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the motorcycle. 3. Install the circlips and flanges from the stock system onto both new head pipes. 4. Install the header using the stock nuts, but leave them loose at this time. 5. Install the new mounting bracket to the frame below the right rear foot peg, using the two 3/8″x 3/4″ flange bolts (supplied), and tighten. 6. Slide the dog bone shaped nut plate under the bracket that is welded to the backside of the muffler.

HARLEY DAVIDSON SOFTAIL Shortshot Exhaust System REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 17-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. On FLSTC, FLSTF, FLSTN and FXSTS loosen the right hand floor board mounting bolts to gain clearance for exhaust removal and installation. 2. Loosen the heatshield clamps on both front and rear exhaust pipes. 3. Loosen the crossover pipe clamp, located between the front and rear head pipe. (This step is not necessary on 2000 models). 4. Remove the two mounting nuts from each head pipe, located at the cylinder head. 5. Remove the bolts that attach the mufflers to the frame. 6. Remove the entire exhaust system and set it aside. 7. On pre 2000 models remove the lower mounting bar. 8. FLSTN, FLSTF and FXSTD models have an upper mounting bar that must be removed in addition to the lower bar. 9. Park the motorcycle on its side stand. Remove the right side 1/4″-20 bolt which holds the lower fender in place. The fender will flex out of the way allowing the removal of the right passenger foot peg bolt. Position a floor jack under the right hand frame tube of the motorcycle below the swing arm pivot bolt. Raise the jack just enough to take the weight off the pivot bolt and remove the bolt and stock mounting bar. Set the mounting bar aside. Replace the pivot bolt and torque it between 120 -150 ft. lbs. Reinstall the passenger foot peg using the 1/2″-20 x 3″ bolt and an 1 5/8″ long spacer (supplied). 10. On 2000 year models, using a #50 Torx driver, remove the three mounting bolts, and set the mounting bar aside. (Two of the bolts are visible, the third is accessed by removing the right hand passenger foot peg.) Replace the foot peg using the 3/8″-16 x 2 1/2″ bolt and 3/4″ length spacer (supplied). 11. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. NOTE: If circlips look bent or twisted replace them with new circlips. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Vance and Hines recommends you replace your exhaust gaskets with Sceamin’ Eagle gaskets part number 17048-98. 2. Install the mounting bracket to the frame, by aligning the two 3/8″ holes in the bracket with the two holes in the frame below the right rear footrest, using the two 3/8″-16 x 3/4″ flange head bolts (supplied), do not tighten at this time. When the bracket is mounting correctly, it should bend out and away from the motorcycle, with the four holes of the bracket toward the front of the motorcycle. 3. Install the circlips and flanges from the stock system on to both of the new head pipes

Incoming search terms:

HARLEY DAVIDSON PIVOT BOLT COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-02-2011

download
This kit fits all 2004 and later XL (Sportster®) model motorcycles INSTALLATION Right-Side Pivot Bolt Cover Installation Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. See Figure 1. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns. 2. Note the position of the bottom-most flat on the rear-fork pivot hex-head bolt (3). Line up the pivot bolt cover over the bolt head so the set screw is centered on the hex flat. Use the 3/32 inch hex key from the kit to tighten the set screw securely to the head of the rear-fork pivot bolt. 3. Make sure the pivot bolt cover is clean and free of any oil or grease. Remove the protective backing from the adhesive disk on the back of the decorative insert (9). Install the decorative insert onto the end of the pivot bolt cover with the image or text upright and parallel to the ground. Press the insert firmly against the end of the pivot bolt cover and hold pressure for 30 seconds. After releasing pressure, avoid direct contact with the insert for about 20 minutes. Left-Side Pivot Bolt Cover Installation 4. Models without passenger footrests: Use an 8 mm hex key to remove the bolt (5) retaining the double-tube clamp (4). Models with passenger footrests: Use an 8 mm hex key to remove the two bolts (5) and the left-side passenger footrest and bracket assembly (6). 5. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns

Incoming search terms:

HARLEY DAVIDSON CHROME FOOTPEG BOLT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE The bolts supplied in this kit are designed for a one-time installation only. If this kit is removed after initial installation, you must re-apply Loctite 243 (Blue) to the threads of the bolts. Kit Contents 3 1 3 is05122a Figure 1. Service Parts: Chrome Footpeg Bolt Kit Table 1. Service Parts Part Number Description (Quantity) Item 94128-01 Washer, chrome (2) 1 8023 Nut, chrome (2) 2 4233 Screw, TORX®, button head, chrome (2) 3 INSTALLATION 1. Remove existing nut and bolt securing footpeg to mount. Discard nut and bolt. 2. See Figure 2. Install chrome washer to bolt, then install bolt through mount and footpeg as shown. 3. Install nut to bolt. Tighten hardware to 10-16 ft-lbs (13.6- 21.7 Nm) . 4. Repeat Steps 1 through 3 for the opposite side

HARLEY DAVIDSON REAR SWINGARM AXLE COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) NOTE XL Sportster 883 and XL1200R models may require loosening or removal of the rear muffler in order to install the right side rear axle cover. See the EXHAUST SYSTEM REMOVAL section of the Service Manual. 1. Support the vehicle, and loosen or remove the rear muffler if necessary. XL Sportster 883 and XL1200R models: Remove the right-side lower shock absorber mounting bolt. Save for re-installation. All other models: Remove and discard the right-side lower shock absorber mounting bolt. 2. Swing the bottom of the shock absorber out of the way. Position the right-side swingarm axle cover (2) over the swingarm and behind the shock absorber. 3. Reposition the shock absorber. XL Sportster 883 and XL1200R models: Install the shock absorber mounting bolt removed in Step 1. All other models: Install the shoulder bolt (3) from the kit. All models: Tighten the bolt to 45-50 ft-lbs (61-68 Nm) . NOTE When torquing the bolt, align two of the bolt-head flats parallel to the ground. This will allow proper orientation of the bar and shield logo on the bolt cover. 4. Position the bolt cover (4) over the bolt head (3) with the Bar-and-Shield logo oriented upright, and lock in place with the set screw (5). Tighten securely. Reposition and tighten the muffler per the Service Manual instructions. 5. Remove and discard the left-side lower shock absorber mounting bolt. Move the bottom of the shock absorber out of the way. Position the left-side swingarm axle cover (2) over the swingarm and behind the shock absorber. 6. Reposition the shock absorber and install the shoulder bolt from the kit. Tighten to 45-50 ft-lbs (61-68 Nm) , aligning two of the bolt head flats parallel to the ground. 7. Position the bolt cover over the bolt head with the Bar-and- Shield logo oriented upright, and lock in place with the set screw. Tighten securely

Incoming search terms:

Ducati Sport Clutch Lever INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 26-10-2010

download
1 To remove your stock lever, use a 19mm wrench or (adjustable wrench) to remove the large sheet metal nut attached to the main pivot bolt that holds the lever. (Photo 1a) Once the locknut is removed, push the main pivot bolt out with your finger or if necessary tap lightly with a rubber mallet or plastic handle end of a screwdriver (Photo 1b) After the pivot bolt is removed, the lever will detach from the master cylinder. (Photo 1c) 1a See other side for further instructions INSTALLATION INSTRUCTIONS FOR PART # CRC552 ® C/5 Sport Clutch Lever Part # CRC552 1b 1c INSTRUCTIONS_CRC552 12/27/07 10:05 AM 23 4 2 Included with your ASV lever is a plastic bag that contains a custom pivot bolt, spacer & locknut. These parts will replace the OEM Brembo parts that were used with your stock lever. 3 Carefully place the lever into the master cylinder while aligning the plunger rod into the plunger cup on your ASV lever as shown in photo 3. 4 Align the lever and the master cylinder pivot bolt holes and Install the main pivot bolt, you will need to pre-load the lever into the master cylinder to get the bolt through the holes. The bolt head has two cut outs on the sides that need to be aligned with the matching area on the master cylinder. Be sure the head of the bolt seats down into the slotted area of the master cylinder. It may be necessary to use a rubber mallet or Plastic end of a screwdriver (Photo 4) to tap the head of the bolt down into its slot. 5 On the other side of the pivot bolt where the threads are, you will see that there is space around the pivot bolt. You will need to install the aluminum spacer that was supplied in the plastic bag with the pivot bolt and locknut. The spacer has a small flange on one side. The flange should be on the outer side when installing it into the hole surrounding the bolt. (Photo 5a) You may need to use pressure to seat the spacer fully into the hole surrounding the pivot bolt. You should be able to do this by using your fingers or thumbs as shown in photo 5b.

HARLEY DAVIDSON DYNA AND SPORTSTER Chrome Front Wheel Spacers INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Block motorcycle underneath frame so front wheel is raised off the ground. 2. See Figure 1. Remove the upper (1) and lower (2) brake caliper mounting bolts and brake caliper(s) (3). Support caliper(s) using a rubber bungee cord. Be careful not to scratch fender paint. NOTES Do not operate front brake lever with the front wheel removed or the caliper piston may be forced out of piston bores. Reseating the piston requires disassembly of the caliper. Prior to removal, make note of existing left and right spacer location. The new spacers will be installed in the locations. 3. See Figure 3. On left side of wheel, remove axle nut (D), lockwasher (E) and washer (F). Perform the following: 4. Sportster and Dyna (except FXDWG) See Figure 2. Loosen the pinch bolt nut (1) and pull the the axle (2) free. Remove wheel and spacers. Leave bearing(s) in place. Discard spacers. 3 1 2 is04469 1. Brake caliper mounting bolt, long (top) 2. Brake caliper mounting bolt, short (bottom) 3. Brake caliper Figure 1. Caliper Mounting Bolts (Left Side) Dyna and Sportster 3 1 2 is04470 1. Pinch bolt nut 2. Axle 3. Pinch bolt Figure 2. Front Wheel Mounting (Dyna and Sportster Except FXDWG-Right Side) 5. See Figure 3. Obtain the new right (1) and left (2) chrome spacers from kit and install. 6. Apply a light coat of ANTI-SEIZE LUBRICANT (Harley- Davidson Part Number 98960-97) to the axle.
7. Place wheel between sliders and install axle. Verify that axle spacers on right and left side are properly installed. 8. See Figure 3. Install the washer (F), lockwasher (E) and nut (D) onto threaded end of axle (A). 9. In order to properly align the front fork, perform the fol- lowing: a. On the right side of the wheel, insert a 7/16 inch drill bit through the hole in the axle. While holding axle stationary, tighten axle nut to 50-55 ft-lbs (61.0-74.6 Nm) . b. Pull fork leg so that it just contacts drill bit. Tighten according to the following: c. Refer to Figure 2. Tighten the Axle Pinch Bolt Nut to 25-30 ft-lbs (33.9-40.7 Nm) . d. Remove drill bit from axle hole. 10. Follow instructions in Service Manual and install brake caliper to the sliders noting the following: •Loosely install long bolt to the top hole on fork leg. Install the short mounting bolt to the bottom hole and tighten to 28-38 ft-lb (38.0-51.5 Nm) . •Final tighten top bolt to 28-38 ft-lbs (38.0-51.5 Nm) . 11. Repeat Step 10 to install brake caliper on opposite side of wheel. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) 12. Pump brake lever to move pistons out until they contact both brake pads. Verify piston location against pads

Incoming search terms:

Incoming search terms: