harley bracket for delorto carb

You search Auto repair manual PDF harley bracket for delorto carb, if there are search results will appear below. If search results do not exist, please search by others keyword.



  harley bracket for delorto carb Direct Download speed 5282 Kb/s

  harley bracket for delorto carb Full Version speed 6162 Kb/s



KAWASAKI 1500 CARB THUNDER Air Filter Kit Installation And removal Instruction

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove Seat 10mm KAW 1500 CARB ADPTOR QTY PARTS LIST 1 1500 CARB ADAPTOR 1 3″ PIECE OF HOSE 1 DOUBLE BARB 1 L-BARB 1 3/8″ RED PLUG 1 ¼” BLACK VACCUM PLUG 1 M6-1 NYLON INSERT LOCK NUT 3 M6-1 X 16 FLAT SOCKET HD CAP SCREW 1 170 MJ 1 INSTRUCTIONS 2) Remove Dash Plaque 8mm bottom Bolt only 3) Lift from bottom then Remove speedo cable 4) Disconnect Electric Plugs 5) Remove 12mm bolts holding tank 6) Turn petcock OFF – Pinch off fuel line. 7) Disconnect the electric Plug under speedo opening 8) Lift Tank at Rear – Disconnect two Vent Lines; Fuel gage Vent will Pull up – Remove. 9) Remove Chrome Air Cover. 10) Left side Remove two screws – 10mm bolt in side Air box. Pull hoses off Remove 1″ hose going to cross over Tube. 11) Remove two 8mm bolts on Bracket – Remove Bracket 12) Remove Screw on Top of air Box Snorkel 13) Remove both side covers 14) Remove air Backing plate right side (Crank Case Breather hose that connects to stock air box will connect to new) 15) Remove Bracket that holds Carb and holds Backing Plate 16) Take idle adjustable Knob loose – let hang loose 17) Take Choke Knob out of holding Bracket 18) Hose that went to cross over tube MAY BE PLUGGED OR VENTED your Choice (Fresh air unit) ** 98′S or any models with carb warmer should disconnect carb warmer by pinching off line on each side of connector that plugs into carb on bottom. Small bracket with one screw directly on the bottom of carb. 19) Loosen Clamp that holds Carb to intake Manifold, Carb will hang loose 20) Remove intake Manifold 5mm Allen- Remove crossover tube. 21) (- BE CAREFULL-) LINE IT UP RIGHT- Replace intake Manifold (YOU MAY TO SEAL THIS WITH A SEALER LIKE PERMATEX) ( BE SUPER CAREFUL TO KEEP INTAKE COVERED DURING EACH STEP. SCREWS CAN FALL ONTO INTAKE) 22) Drain Float Bowl 3mm allen – very bottom of carb 23) Remove Float Bowl 4 screws (#2 Phillips) let hang down 24) Remove main jet, if Emulsion tube comes out use 8mm and Flat tip to separate jet from Emulsion tube. 25) Install with new jet 26) CAREFULLY Reinstall Float Bowl Cover 27) If installing Needle Remove Top Cover of Carb, Carefully pull the slide out. ( BE CAREFUL WITH DIAPHRAM) Remove Spring + Needle Install new Needle (WE RECOMMEND THE 3RD CLIP FROM TOP WITH TWO WASHERS ON TOP. REINSTALL 28) Be sure to reseat diaphragm – BE CAREFUL Reinstall Cover. 29) Install Carb to Intake – reconnect carb warmer if applicable 30) Reattach idle adjustment 31) Reattach Choke 32) Reattach Bracket in front of Carb- 33) Take Center bolt mount Rubber Gromlet from Stock Air box Plate install in to new Air box Adapter use stock Bolt, Attach to Bracke

Incoming search terms:

HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

HARLEY DAVIDSON RIDER BACKREST MOUNTING HARDWARE KIT INSTALLATION INTSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
INSTALLATION 1. Remove seat according to the instructions in the service manual. 2. Remove the ECM caddy/battery cover by removing two screws. 3. See Figure 1 and Figure 2 for the mounting locations of the brackets. NOTE Some seats may limit the fore/aft mounting location of the backrest bracket. 4. See Figure 3 and Table 1. Remove plastic protective cap and locknut from stud. Leave the small plastic washer in place or the stud plate will fall out. With the backrest mounting bracket tab facing forward, attach the backrest mounting bracket (1) to stud plate with stock locknuts from the stud plate. 5. Tighten locknuts to 5-8 ft-lbs (6.8-10.8 Nm) . 6. Attach the front mounting bracket (6) to the frame cross- member using using two flange screws (8) and flange nuts (7). Tighten screws to 72 in-lbs (8.1 Nm) . 7. Attach the bracket support (2) to the front mounting bracket (6) with screw (8) and nut (7). 8. Install screw (5) and nut (9) to bracket support and backrest tab and tighten to 15 ft-lbs (20.3 Nm) . 1 2 is05475 1. Backrest mounting bracket 2. Front mounting bracket Figure 1. Bracket Mounting Locations 3 2 1 is05476 1. Backrest mounting bracket 2. Front mounting bracket 3. Bracket support Figure 2. Backrest mounted After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) -J04733 1 of 2
9. Install the ECM caddy/battery cover using two screws previously removed and tighten to 6-8 ft-lbs (8.1-10.8 Nm) . 10. Install seat according to service manual instructions. 11. Hold slit between rider and passenger seat open. On rider backrest, compress backrest rods and spring. Insert rods into backrest mounting bracket. Backrest Pad Adjustment 1. Adjust fore/aft position of backrest pad. Use 3/16 inch hex wrench to adjust set screw that is accessible through eyelet opening on rear of pad. If possible, do not remove set screw because it is difficult to install.

Incoming search terms:

HARLEY DAVIDSON ROAD TECH XM SATELLITE RADIO RECEIVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
INSTALLATION NOTE Do not use solvent-based chemicals or waxes directly on the plastic or rubber components as they can affect the overall performance and appearance of the plastic and rubber. Models with main FUSE: To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Service Manual and follow the instructions given to remove the main fuse. Models with main CIRCUIT BREAKER: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) -J03989 1 of 8
Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Receiver Mounting Bracket Installation When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. ALL models: See FUEL TANK: REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual for instructions to remove the tank. 3. Using a T-27 TORX drive head, remove the two screws that retain the clutch-lever clamp to the handlebar. 4. See Figure 4. Obtain the correct mounting bracket (2) for your vehicle, and two button-head screws (3) and spacers (4) from the kit. Insert the button-head screws into the mounting bracket, through the holes above and below the slot. Place a spacer over the threads of each screw. Insert the screw threads into the holes in the clutch lever clamp removed earlier. 5. Adjust the hand lever position for rider comfort and posture, then tighten the screws to 60-80 in-lbs (6.8-9.0 Nm) . Receiver and Antenna Bracket Installation 6. Obtain the satellite radio receiver (1), antenna bracket (6), and four lock nuts (8) from the kit. Insert the four studs on the back of the receiver through the four holes in the receiver mounting bracket. 7. See Figure 4 for mounted position of the antenna bracket to the receiver mounting bracket. Assemble a lock nut to each of the bottom two studs. Install the antenna bracket onto the top two studs, and assemble a lock nut to each top stud. Tighten the locknuts securely. Antenna Installation 8. Obtain the XM radio antenna (5) and two-sided adhesive tape (7) from the kit. 9. Use isopropyl alcohol to clean the horizontal antenna mounting surface of the antenna bracket, and the bottom (mounting) surface of the antenna. 10. Peel the liner from one side of the tape, and apply the tape squarely to the bottom surface of the antenna. 11. Peel the liner from the exposed side of the adhesive tape on the antenna base. 12. Position the antenna over the bracket without touching the adhesive to the bracket. Center the antenna over the bracket with the antenna cable toward the center of the vehicle. 13. Press the antenna squarely and firmly onto the bracket, and hold pressure for about 60 seconds. After releasing pressure, avoid direct contact with the antenna for about 20 minutes. HARNESS ROUTING AND CONNECTION

HARLEY DAVIDSON SOFTAIL FRONT SPOILER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 2 and Table 1. INSTALLATION 1. Position the vehicle on a motorcycle lift table. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 3. Raise the vehicle on the lift table to allow access to the lower front portion of the frame. 2008+ 2007 7 8 11 3 3 4 4 12 5 5 1 1 9 2 2 10 6 6 9 9 11 13 is02652c 8. 1. Two-pin voltage regulator connector (2007 only) Voltage regulator 2. 9. Voltage regulator attaching screws (2) Cable strap (2 for 2007, 1 for 2008 and later) 10. 3. Lower voltage regulator cover (2007 only) Voltage regulator bracket 4. 11. Bracket screw to engine crankcase (2) Oxygen sensor connector 12. 5. Crank position sensor connector (2007 only) Voltage regulator caddy 6. 13. Voltage regulator caddy cover Horn connectors (some 2008 and later models) 7. Four-pin voltage regulator connector (2007 only) Figure 1. Original Equipment Voltage Regulator  NOTE For 2007 models: The ground wire on the voltage regulator must be re-attached at the original location when re-installing the voltage regulator to ensure adequate ground. 4. For ALL models: See Figure 1. Remove and discard the voltage regulator caddy cover (6) from the regulator bracket (3) and caddy (5). For 2007 models: In addition, remove the lower voltage regulator cover (10). 5. Remove and retain the hex socket head screw (4) at the top left of the bracket For 2007 models: In addition, disconnect the ground wire. Free the cable straps (9) from the regulator bracket, beneath the regulator. 6. Remove the two hex socket head screws with washers (2) retaining the voltage regulator to the bracket. Remove and save the regulator, but discard the screws. 7. Remove and retain the screw (4) at the top right of the regulator bracket. Remove the bracket from the engine. 8. For 2008 and later models: Free the strap (9) that ties the jiffy stand wiring to the voltage regulator bracket. Unfasten the three-way jiffy stand sensor connector and the two-way crank position sensor connector [79] (12) from the T-studs on the back of the regulator bracket (3). Discard the bracket. Disconnect both plugs from the back of the voltage regulator (1). For 2007 models: Unfasten the four-way (7) and two-way (8) voltage regulator connectors from the T-studs on the back of the regulator bracket (3), and discard the bracket. Disconnect the voltage regulator (1) at both connectors. 9. For 2008 and later models: Unclip the two-way O 2 (oxygen) sensor electrical connector [138] (11) from the voltage regulator caddy (5). For 2007 models: Unfasten the two-way crank position sensor connector [79] (12) from the voltage regulator caddy (5). Remove the caddy from the vehicle frame. a. For 2007 models: Unclamp the bottom of the caddy from the engine mount spacers. b. For ALL models: Unhook the top clips from around the tabs on the front of the engine casting. Remove the original equipment (O.E.) caddy from the vehicle frame, and discard it.

Incoming search terms:

HARLEY DAVIDSON MOUNTING BRACKET SERVICE MANUAL

0

Filed Under (Harley Davidson) by admin on 12-04-2011

download
INSTALLATION 1. See Figure 1. Note position of mounting brackets (1). Remove old mounting brackets and discard. NOTE On 1997-2000 models, the air fittings are installed to the two mounting holes on the right-hand right side bracket. On 2003 and later models, the single air fitting is installed to mounting hole on the left-hand side bracket. 2. See Figure 2. Install new mounting brackets from kit on each side of the motorcycle using new locknuts as follows: a. Use the 5/16-18 x 1 inch screws (5) in the upper two holes with 2 chrome washers (3) placed between the mounting bracket and the saddlebag support at each of the two locations. Install a 5/16-18 flange locknut (2) behind the screw that does not screw into a weld nut. Tighten to 15-19 ft-lbs (20-26 Nm). b. On each side, install a 1/4-20 x 7/8 inch screw (9) through the bottom hole of the mounting bracket and the saddlebag bracket as shown, with a chrome washer (3) placed between the mounting bracket and the saddlebag bracket. Tighten to 10-14 ft-lbs (13.5- 19.0 Nm). On 1997-2002 models, install the air line fittings to the lowest two holes drilled in the right side bracket. On 2003 and later models, install the single air line fitting to the lower front hole drilled on the left side bracket. c. See Figure 2. On each side, attach docking points (6) in their proper location on mounting bracket with 3/8- 16 x 1-1/2 in. buttonhead screws (7), washers (3) and locknuts (8) but leave locknuts slightly loose so docking points can be adjusted for proper fit. On 1997and later models, the docking point will attach through the front hole of the mounting bracket as shown. On 1994-1996 models, the docking point will attach through the rear hole of the mounting bracket. d. Place detachable passenger backrest into docking points as described in the Backrest Instruction Sheet. Make sure that the forward notches of the sideplates are pushed completely into the forward docking points, then tighten the rear docking points securely to 45-47 ft/lbs (61.0-64.0 Nm

HARLEY DAVIDSON THERMOMETER/ CLOCK, HAND LEVER BRACKET CLAMP MOUNT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION NOTE The figures show the gauge mounted to the clutch (left-hand) lever clamp. The gauge can be mounted on either the clutch or brake lever side, using the upper or lower clamp mounting screw per customer preference. 5 3 1 2 4 is01874 1. Gauge 2. Bracket (bent backward) 3. Socket head set screw from this kit 4. Original equipment screw 5. Original equipment washer (front of bracket) Figure 1. Gauge Bracket Mounted to Upper Screw (Left-Hand Shown) 1. See Figure 1 and Figure 2. Using a T27 TORX drive head, remove the desired screw (upper or lower) with flat washer securing the handlebar clamp to the hand lever bracket. NOTE When mounting the gauge bracket to the lower clamp mounting screw, install the original flat washer behind the bracket. 2. Install the handlebar clamp screw with flat washer through the larger hole in the gauge bracket, and tighten to 60-80 in-lbs (6,8-9,0 Nm). 3. Rotate the gauge to the desired angle, then tighten the gauge attaching screw securely. SETTING THE TIME ON THE CLOCK NOTE The clock is shipped with the stem pulled out, which stops clock operation. If the stem has been pushed in, pull out the stem carefully, and turn it until the hands indicate the correct time. Carefully push the stem back in to start the clock. REPLACING THE CLOCK BATTERY The clock battery (Type SR626SW) is a common type, available wherever watch batteries are sold. It is recommended that the battery be replaced at a watch repair facility, as the screw back cover requires a special tool for removal and replacement. The clock is waterproof, and requires special attention when re-assembled.

HARLEY DAVIDSON XR1200 LUGGAGE RACK KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2011

download
Kit 53976-08 (XR1200 Passenger Upright Kit) is available for separate purchase. Contact your Harley-Davidson dealer for more information. Kit Contents See Figure 2 and Table 1. REMOVAL 1. Remove pillion and seat following the instructions in the appropriate Service Manual. 2. Remove the seat base following the instructions in the appropriate Service Manual. 3. See Figure 1. Remove the turn signal mounting screws (3) and discard. Allow the turn signal to hang by the harness until lower bracket installation. 4. Remove the rear fender support strut screws (6) and dis- card. INSTALLATION 1. See Figure 2. Install lower luggage rack mount bracket with screws (9), flat washers (10) and nuts (8). Bracket will mount around nut (Item 2 in Figure 1). Tighten to 19 ft-lbs (26 Nm) . 2. Install screws (7) and nuts (8) through the rear fender support strut and the lower luggage rack mount bracket. Tighten to 19 ft-lbs (26 Nm) . 3. Route the turn signal wire harnesses through the groove in the bracket. Install new turn signal mounting screws (11). Tighten screws to 3-5 ft-lbs (4-7 Nm) . 4. Install seat base following the instructions in the appropriate Service Manual. 5. Install upper luggage rack mount bracket (4) with original equipment seat base screws in the lower holes (A). Do not tighten at this time. 6. Install screws (3) into slotted holes in the upper luggage rack mount bracket (4) and flange nuts (6). Slide the upper bracket as far back in the slots as possible. Tighten screws (3) to 10 ft-lbs (13.5 Nm) 4 1 1 2 5 6 3 is05250 1. Lower luggage rack mount bracket screw (4) 2. Nut (2) 3. Turn signal mounting screw (4) 4. Upper luggage rack mount bracket 5. Luggage rack 6. Rear fender support strut screw (2) Figure 1. Luggage Rack Installation NOTE If installing the Passenger Upright Kit (part number 53976-08) (available separately), do not install spacers (2) and screws (3) in front holes. 7. Install luggage rack (1) aligning the holes with the holes in the upper luggage rack mount bracket. Install spacers (2) and screws (3) in holes. Tighten to 6-10 ft-lbs (8-13.5 Nm) . After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 8. Install pillion and seat following the instructions in the appropriate Service Manual. Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a

YAMAHA Road Star Fuel Pump Relocation Kit INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove seat and disconnect battery. Remove fuel tank along with both left and right side battery covers, and remove air box from carburetor (all per Yamaha standard shop manual procedures). 2. Remove chrome plastic cover over fuel pump and disconnect choke cable/knob from lower pump bracket. Remove pump-to-carb fuel line from fuel pump. Disconnect fuel pumps electrical lead connector. 3. Remove two (2) hex-head pump mounting bracket bolts and remove pump assembly from motorcycle. Slide fuel pump up and off bracket mounting posts (Caution: excess fuel may drain from pump and/or fuel lines and fuel filter!). Remove heat shield. Remove remaining fuel line from pump. Pull all fuel lines from filter and remove steel springs and hose clamps from these lines (these will be reused on the kits fuel lines). With a sharp knife or box cutter, trim off the top portion of the fuel pumps rubber isolation/mount system per Photo A. Next cut pumps wiring harness approximately half way between connector and pump. Strip the insulation from the ends of these wires as well as from the supplied Baron harness extension wires. Using the supplied electrical butt connectors, crimp Baron harness extensions red wire to pumps black-w/blue-strip wire, and Baron harness extensions black wire to pumps black wire. Repeat this process on other side of wire harness extension with pumps connector. Now, referring to Photo B, you will need to cut off the square tube that runs along the side of the fuel pump with a hack saw. Cut down toward pump body in a straight cut, then cut tube off by cutting along the body. This will allow you to twist pump in the rubber mount so the curved spigot is facing up (clockwise approx 1/4 turn). 4. Remove pump-to-carb fuel line from carb and separate electrical wires from this line. Remove this fuel line from engine. Re-route choke cable to right side of engine (toward carb) and rotate it up and over rear cylinder head back toward left side of bike. Mount new Baron choke bracket to the choke cable and tighten plastic nut. New choke bracket will mount to rear fuel tank mounting location (Photo C). 5. 99~03 models – Remove electrical relay bracket (found under the right side cover) from the bike and slide each relay off of this bracket. Install fuel pump onto new Baron Fuel Pump Bracket and install bracket in the same location as the stock bracket you just removed, using stock mounting hardware. Refer to Photo F for proper installation. 6. 04~07 models Remove electrical relays from stock bracket and remove relays from rubber holder. Cut rubber holder per Photo E and replace one of the relays into the rubber and install on to new Baron bracket. The second relay will be placed to the right of the tool bag under the seat and secured with the provided two-sided tape pad. Reconnect plugs to the relays. (Photo F)

Incoming search terms:

Harley davidson Sportster Custom Straightshot Exhaust System REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove the nut that mounts the front muffler to the engine, located below the rear brake master cylinder. 4. Remove the bolt that mounts the rear muffler to the mounting bar. 5. Remove the entire exhaust system and set it aside. 6. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them with new circlips . INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Vance and Hines recommends you replace your exhaust gaskets with Sceamin’ Eagle gaskets part number 17048-98. 2. Install the circlips and flanges from the stock system on to both of the new head pipes. 3. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of both heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear heat shield. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Install the front head pipe using the stock nuts, do not tighten at this time. 5. Install the rear head pipe using the stock nuts, do not tighten at this time. 6. Install one muffler clamp (supplied) over the inlet (notched end) of each muffler. 7. Identify the front and rear muffler mounting brackets. The front bracket is stamped with the number 305 and the rear muffler bracket is stamped 213 . 8. Install the front muffler mounting bracket to the stud on the engine (where the stock muffler mounted) and fasten using the stock nut (leave loose at this time). The bracket will bend inward towards the center of the motorcycle when installed correctly. Note: You may need to move the wires and hoses on the lower frame rail to decrease the possibility of them chaffing on the bracket bolts. 9. Slip one of the mufflers onto the front head pipe. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the muffler to the mounting bracket using the 5/16″ flange head bolts (supplied) leave them loose at this time. 10. Attach the rear mounting bracket to the rear muffler. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the bracket to the muffler using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note: The single hole in the bracket will point downward and slightly forward when installed correctly

Incoming search terms: