harley davidson key fob instructions

You search Auto repair manual PDF harley davidson key fob instructions, if there are search results will appear below. If search results do not exist, please search by others keyword.



  harley davidson key fob instructions Direct Download speed 5282 Kb/s

  harley davidson key fob instructions Full Version speed 6162 Kb/s



HARLEY DAVIDSON SECURITY SYSTEM KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
FL Touring models equipped with a TLE/ TLE Ultra Sidecar will require the additional installation of a Bank Angle Switch Kit (88115-03) and is available for separate purchase. See a Harley-Davidson dealer.INSTALLATION 1. Remove the original equipment (OE) Turn Signal Module (TSM) or Body Control Module (BCM) following the instructions in the service manual. 2. Install the Bank Angle Sensor (BAS) on sidecar vehicles. 3. Install the new turn signal/security module (TSSM) (7), Hands Free Security Module (HFSM) (1) or BCM (9, 11) from this kit, following the instructions in the service manual. Configure the Trike or sidecar TSSM, HFSM or BCM to “Side Car Enabled” using Digital Technician. 4. Install the Hands Free Security Module (HFSM) Antenna and antenna mount (6) if necessary, using the service manual instructions. Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) ACTUATION 1. See a Harley-Davidson dealer to activate the key fob to the TSSM, HFSM or BCM. NOTE You can activate the TSSM fob by referring to the procedure in the electrical diagnostic manual. TRIKE AND SIDECAR CONFIGURATION (FL TOURING MODELS ONLY) Only Touring Harley-Davidson Motorcycles are suitable for sidecar use. Consult a Harley-Davidson dealer. Use of motorcycles other than Touring models with sidecars could result in death or serious injury. (00040a) NOTES FL Touring Models equipped with TLE/TLE-Ultra Sidecar require the installation of a Bank Angle Sensor (88115-03). Failure to install and configure a Bank Angle Sensor may result in death or serious injury. Sidecar and Trike configuration of the security system requires the use of a Digital Technician. Consult your Harley-Davidson dealer or the sidecar or Trike service manual for complete details. On vehicles equipped with a sidecar, the security system must be reconfigured from the default solo vehicle setting to the sidecar setting

Incoming search terms:

HARLEY DAVIDSON LOCKING FUEL FILLER CAP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION 1. Prior to installing the gas cap on the vehicle, insert the key into the lock. Firmly grasp the chrome top of the fuel cap and turn the key until it stops. On right hand threaded fuel caps, turn the key counter-clockwise until it stops. On left hand threaded fuel caps, turn the key clockwise until it stops. This assures an unlocked position for the gas cap. Allow the key to return to the neutral position. 2. Remove the key and install the fuel cap on the vehicle. is00770 Figure 1. Right Hand Threaded Fuel Cap Installation NOTE When installing the fuel cap, rotate the cap one full turn past the audible click. This automatically positions gas cap to lock position. A properly locked/installed gas cap will rotate freely in both directions. Failure to do so will give an incorrect assumption that the fuel cap does not work properly. REMOVAL On right hand threaded fuel caps, insert key, and while holding the gas cap in place with hand, turn key counterclockwise until it stops, return key to original position. Gas cap must rotate 270 degrees counter-clockwise before mechanism engages to allow gas cap removal. Continue to rotate counterclockwise to fully remove gas cap. On left hand threaded fuel caps, insert key and while holding the gas cap in place with hand, turn key clockwise until it stops, return key to original position. Gas cap must rotate 270 degrees clockwise before mechanism engages to allow gas cap removal. Continue to rotate clockwise to fully remove gas cap. REPLACEMENT KEYS Record the 4 digit key number stamped on the back of the key opposite the Harley-Davidson logo, in the area provided below. If a replacement key is needed, see your Harley-Davidson Dealer with the 4 digit number to order a replacement

Incoming search terms:

1999-2001 DUCATI Monster INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
It is essential to use Blue Loc-tite on all nuts and bolts. Remove any other steering stabilizers. 2) Cover the tank with an old sweatshirt or protective device so you don’t scratch it. 3) General concept for this mount: The new key cover is the anchor point for the stabilizer, so it must be fitted correctly as per the instructions below. The base of the new key cover must sit flush all the way around to provide the support needed. The bolt lengths are critical, so be sure you read the instructions carefully so you know which bolts go in which spots! 4) Remove the (4) 8x85mm Allen bolts that hold your handlebars tight. There are plastic plugs in the tops of these bolts that must be removed before you can access the Allen head. Replace the stock top barclamp with the one provided in the kit. 5) Tighten the 4 bolts evenly so the gaps between upper and lower perches, front to back, are even. 6) Remove the (2) 6x12mm Allen bolts and the plastic key cover that covers your key switch. 7) Fit the new billet aluminum key cover over the key switch and be sure the new cover is sitting down flush all the way around on the frame. It needs to be touching the frame to function properly. We’ve machined this part to fit precisely on the bike but each bike can vary slightly due to machining variations from the Ducati Factory. The new key cover should center itself by locating on the 2 spacer/nuts underneath. You might need to loosen the 2 bolts on the underside of the frame to allow those spacer/nuts to find their centering point on our key cover. 8) Note: Your stock key switch itself has a casting knub near its base that could restrict our new cover from sitting all the way down flush. We’ve machined a clearance notch inside our part for this knub to fit into, but it is possible it could vary from bike to bike, which might require a bit more clearance filing. Be sure the key cover is sitting down flush against the frame. 9) We’ve machined the key cover to fit over a 20mm spacer nut / .805″. If for some reason the stock “spacer/nuts” are too tall, you may have to file them slightly to allow the Billet key cover to sit down flush and touch the frame. 10) Once the key switch cover is flush against the frame, all the way around it’s base, retighten the bolts that hold the spacer/nuts secure from the under side of the frame using Loc-tite. Reinstall the (2) 6x12mm stock key cover bolts to a maximum of 6-ft/lbs . The stock key cover bolts are designed to engage 6mm of thread in the spacer nut. Do not be tempted to use any longer bolts than 6x12mm or they can prematurely bottom out which will keep the key cover from tightening. Shorter than 6×12 or if the cover is not flush, makes it possible to damage the threads. Double check these key-cover bolts after your first ride, as they may loosen after initial movement from the damper

Incoming search terms:

HARLEY DAVIDSON SECURITY SYSTEM SMART SIREN KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
REMOVAL 1. Refer to the owner’s manual and follow the instructions to disarm the security system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. For All Models except 2002-2003 Touring and 2003- Later Softail: Refer to the owner’s manual and follow the instructions to disconnect the battery, negative (-) cable first or remove the main fuse. For 2002-2003 Touring and 2003-Later Softail Models: Remove seat following the instructions in the service manual and disconnect the battery, negative (-) cable first. Save seat hardware for installation. INSTALLATION 2002-2006 VRSCA, VRSCB, VRSCD Models 1. Open the seat. 2. See Figure 1. Remove the splash guard (mud flap) nuts. 3. See Figure 2. Lower the mud flap from the installed position and allow it to rest on the rear tire 3. Slide the siren into place on the left side of the electrical caddy so the sounder disc (6) faces out. 4. Refer to the owner’s manual and follow the instructions to install the main fuse. 5. Align the barbed studs on the side cover with the grommets in the frame and push side cover firmly into place. 6. Install the left side saddlebag per the instructions in the owner’s manual. 2003 and later Softail Models EXCEPT FXCW/C 1. Remove the right side saddlebag (if equipped) per the instructions in the owner’s manual. NOTE The siren connector is installed on an electrical panel under the rear fender on all Softail models. The rear of the motorcycle may have to be raised slightly to allow removal of the splash guard. 2. Remove the two bolts at the bottom of the splash guard. Bend the upper right corner of the splash guard toward the rear tire and lift upward to unhook the splash guard from the tab on the rear fork. Remove the guard from beneath the fender. 2 1 3 is01316 1. Siren mounting area 2. Siren connector [142B] 3. Harness clip Figure 16. Siren Connector (Softail Models EXCEPT FXCW/C) (Rear Fender View with Rear Wheel Removed) 3. See Figure 16. Remove the siren connector [142B] (2) from the receptacle in the siren mounting area (1) of the electrical panel. 4. See Figure 17. Insert security siren (1) connector [142B] into the siren box receptacle until the connector latches securely. 5. Orient the siren (1) as shown, with the harness connector (2) toward the bottom and the sounder disc (5) facing out. Carefully snap the siren into the electrical panel. 6. Insert the siren harness lead (4) into the harness clip (3) to keep the harness clear of other components. 7. If necessary, secure the connector wiring to the electrical panel wiring with a cable strap (not provided). 8. Hook the slot at the top of the splash guard over the tab on the rear fork and install the guard with the two screws removed earlier. Tighten securely. 9. Install the right side saddlebag (if equipped) per the instructions in the owner’s manual. 10. Refer to the owner’s manual and follow the instructions given to connect the battery cables or install the main fuse

Incoming search terms:

HARLEY DAVIDSON ADVANCED AUDIO CB RADIO KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
2006 models: communication switch 77173-06 2007 models: communication switch 77173-07 2008 models: communication switch 77173-08 FLHT models will require prior installation of: •Advanced Audio AM/ FM/ CD Radio Kit (76412-06) •AM/ FM Antenna Kit (76325-06 or 76317-06) Unless one has already been fitted as part of another Advanced Audio kit installation: 2006-2007 FLHX models will require the separate purchase of: •fuel tank console (61270-98A), •tank console gasket (71294-89), •a button-head screw (3652), •nut (7964) •clip (10103 and 10120). •tank pod mounting screws (2462) quantity 3 •FLHT trim piece (52447-96) and cb pod trim badge 2008 FLHX models: •fuel tank console (61270-08) •clips (10103 and 10120) NOTE The console screws, fuel door, gasket, mounting bracket will all need to be reused. FLTR models will require the separate purchase of: •a Console Pod Assembly (77136-03), and •three pan-head screws (2462). NOTE See a Harley-Davidson dealer for availability of optional decorative inserts for the Console Pod Assembly. ALL models will require the additional purchase of: •a Non-Ultra Overlay Harness (70169-06), and EITHER : •a Premium Stereo Helmet Headset (77147-98) OR a Hand-Held CB Microphone Kit (76312-98), All of these items are available from a Harley-Davidson Dealer. If two modules are already installed on top of the radio, two Dual-LockTM mounts, (76434-06), will be needed. Models WITHOUT a Tour-Pak installed will require the additional purchase of a Frame Mount CB Antenna Kit (76415- 06). Models WITH a Tour-Pak installed will require the additional purchase of a Tour-Pak Mount CB Antenna Kit (76414-06). All of these items are available from a Harley-Davidson Dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Electrical Overload It is possible to overload your motorcycle’s charging system by adding too many electrical accessories. If your combined electrical accessories operating at any one time consume more electrical current than your vehicle’s charging system can produce, the electrical consumption can discharge the battery and cause vehicle electrical system damage. See a Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories, or for necessary wiring changes. (00211b)

Incoming search terms:

2010 Harley-Davidson FLHR Road King front and rear 4-piston braking system Installation

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
in Vivid Black with blue and silver pinstripes, six-speed. Air-cooled, Twin Cam 96™ engine with Electronic Sequential Port Fuel Injection (ESPFI), ABS, security system, cast wheels with independent front and rear 4-piston braking system. Motorcycle generously donated by Harley-Davidson Motor Company Police & Fleet Sales. MSRP excludes all taxes title/documentary fees, registration, tags, dealer prep, labor and installation charges, insurance, optional equipment and accessories, certificate of compliance or non-compliance fees, and finance charges. Delivery must be coordinated through Rockville Harley-Davidson by November 30, 2010. Winner is responsible for any applicable fees above. 6,000 tickets printed. Odds of winning are 1:6,000. Ticket holder need not be present to win. Licensed by the D.C. Lottery and Charitable Games Control Board. Must be 18 years or older to win. No substitutes, return for cash, or other models. As per IRS tax code, amounts paid for chances in a raffle do not qualify as a deductible charitable contribution. Taxes on prizes are the responsibility of the winner. Harley-Davidson is proud to be a sponsor of the National Law Enforcement Officers Memorial Fund. Harley-Davidson Motor Company is a prize provider only, and Harley-Davidson, Inc., and Harley-Davidson Motor Company have no responsibility regarding conduct or administration of the raffle.

Incoming search terms:

2004 Harley Davidson Micro Tach Tachometer Installation Instructions

0

Filed Under (Harley Davidson) by admin on 26-03-2012

download
Tachometer Installation Instructions for 2004+ Harley Davidson Sportster Custom Look for other model instructions online at www.speedwayinstruments.com Introduction: Installation of the Speedway Instruments microTach+ TM tachometer Tachometer requires some basic mechanical skills, including removing decorative covers, cutting protective tubing around wires, and using suitcase splice connectors to splice existing wiring harness. These actions may void your warranty, and if done incorrectly may cause damage to your motorcycle. Only you know your capabilities, if you do not feel capable of making modification please have a qualified motorcycle technician install it. Speedway Instruments, LLC is not responsible for damage to your motorcycle due to improper installation. These instructions utilize a 2004 Harley Davidson XL1200C motorcycle as basis for the all descriptions and pictures. Variations in location, color and procedure may be required for different year and make. Please refer to the Service manual to confirm the proper color and location of wires. Please make sure you have the proper service manual and tools before starting the installation. 1. Turn ignition off and disconnect Battery. 2. Determine a mounting position. Each motorcycle is unique and the microTach+TM tachometer is small enough to be placed in many different locations to provide an attractive appearance and vital engine status. Possible locations are: a. Front Brake Reservior b. Top handle bar clamp

HARLEY DAVIDSON ELECTRA-GLO LIGHT POD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION NOTES Clean the controller mounting area and the areas where the light pods will be mounted with soap and water before beginning the installation, and allow to dry thoroughly. Remove debris, dirt and grime from the vehicle areas to be highlighted. Ambient temperature should be at least 50 °F (10 °C) for proper adhesion of the light pods and controller box to vehicle surfaces. Light pods should not be located closer than 2.5 inches (63.5 mm) from exhaust pipes or mufflers, and must have 1.5 inches (38.1 mm) clearance from engine cylinders and heads. Do not install light pods with the light source facing directly away from the vehicle. Installation should be done in a way that allows the light to be seen indirectly by reflecting from chrome or painted surfaces of the vehicle. Prepare the Motorcycle To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the owner’s manual and follow the instructions given to disconnect the battery cables, negative (-) cable first. NOTE For 2004 and later XL (Sportster®) models, the negative battery cable is most easily disconnected at the engine crankcase . Locate and Install the Controller NOTE Do not mount the controller box in a location where vehicle suspension travel could result in contact with the ON/OFF switch or dimmer control. Damage to the controller box will occur. 2. See Figure 2. Locate the controller box (10) on a flat surface that will allow the red (+) and black (-) leads to reach the battery terminals and the rider to access the controls (with the vehicle parked) and, if necessary, the in-line fuse holder (A). a. Test-fit the controller box to the selected surface before installation. Do not remove the adhesive backing until ready to attach the controller box. b. Clean the controller box mounting area with one of the included alcohol swabs. Allow to dry thoroughly. c. Remove the liner from the adhesive backing of the controller box. Carefully position the controller box to the surface, and press firmly into place. Hold the controller box in position with steady pressure for about one minute. Connect the Battery Cables NOTE Verify that the ignition/light key switch is in the OFF position before attaching the battery cables. 3. Verify that the ignition/key switch is turned to the OFF position. Apply a light coat of Harley-Davidson electrical contact lubricant (part number 99861-02), petroleum jelly or corrosion retardant material to the battery terminals. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 4. Refer to the owner’s manual and follow the instructions given to install first the vehicle’s positive (+) battery cable then the red (+) light pod controller lead ring terminal to the positive (+) battery terminal. Tighten to owner’s manual specifications. Install first the vehicle’s negative (-) battery cable then the black (-) light pod controller lead ring terminal to the negative (-) battery terminal. Tighten to owner’s manual specifications. Arrange the Electra-Glo Light Pods NOTES Electra-Glo light pods (1) can be installed in a variety of locations. They are best installed on a flat surface to provide indirect lighting illuminating mechanical features, vehicle finish or for ground effects. Refer to the notes at the beginning of the Installation section. 5. Select the area or lines of the motorcycle to highlight, and suitable locations for each light pod. DO NOT permanently affix the light pods at this time. Lightly tape the pods in place temporarily until the desired visual effect is achieved Verify clearance from movement of rubber mounted engine or other moving parts, heat sources, or chafe points

HARLEY DAVIDSON STEERING HEAD WASHER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
INSTALLATION The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. 1. See Figure 1. Remove the fork stem cap (1). Bend the lockwasher (2) tab away from the steering stem nut (3) and remove the fork stem nut and lockwasher. Discard the lockwasher. NOTE Always tighten the steering stem nut (3) to 70 – 80 ft-lbs (95 – 109 Nm) before measuring fall away. Lubricate threads of nut with a small amount of clean engine oil. Avoid applying oil to the mating surfaces of the steering stem nut (3) and the new hardened washer from the kit. 2. Install the new hardened washer from the kit (2) and steering stem nut (3). Tighten steering stem nut (3) to 70 – 80 ft-lbs (95 – 109 Nm). 3. Check fall away following the instructions in STEERING HEAD BEARINGS BEARING ADJUSTMENT (FALLAWAY) in an appropriate Service Manual, however, tighten the steering stem nut (3) to 70 – 80 ft-lbs . Adjust adjusting nut (5), if necessary per instructions. 4. Install fork stem cap (1).

Incoming search terms:

Harley-Davidson FLOATING BRAKE ROTOR (DISC) KITS Removal and Disassembly

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. Models WITHOUT maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. NOTE For 2004 and later XL (Sportster®) models, the negative battery cable is most easily disconnected at the engine crankcase . Removal and Disassembly 2. Refer to FRONT WHEEL: REMOVAL or REAR WHEEL: REMOVAL in the Service Manual, and follow the instructions to remove the wheel from the motorcycle. Use a TORX® drive head to remove the screws retaining the currently installed brake disc to the wheel. The brake disc and screws can be discarded. 3. Inspect the wheel bearings per the PRELIMINARY INSPECTION instructions in the appropriate WHEEL section. Follow the DISASSEMBLY and CLEANING AND INSPECTION instructions as necessary to properly service the wheel. Reassembly and Installation Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 4. Refer to WHEEL: ASSEMBLY in the Service Manual, and follow the instructions to install the new brake disc to the wheel, using the new TORX screws from the kit. Complete the ASSEMBLY instructions as necessary to service the wheel. 5. Refer to WHEEL: INSTALLATION in the Service Manual, and follow the instructions to re-install the wheel to the motorcycle. Return to Service 6. Verify that the Ignition/Light Key Switch is turned to the OFF position. 7. Models WITH maxi-fuse: Refer to the Service Manual and follow the instructions given to re-install the maxi-fuse

Incoming search terms: