harley davidson sidecar mounting brackets

You search Auto repair manual PDF harley davidson sidecar mounting brackets, if there are search results will appear below. If search results do not exist, please search by others keyword.



  harley davidson sidecar mounting brackets Direct Download speed 5282 Kb/s

  harley davidson sidecar mounting brackets Full Version speed 6162 Kb/s



HARLEY DAVIDSON SECURITY SYSTEM KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
FL Touring models equipped with a TLE/ TLE Ultra Sidecar will require the additional installation of a Bank Angle Switch Kit (88115-03) and is available for separate purchase. See a Harley-Davidson dealer.INSTALLATION 1. Remove the original equipment (OE) Turn Signal Module (TSM) or Body Control Module (BCM) following the instructions in the service manual. 2. Install the Bank Angle Sensor (BAS) on sidecar vehicles. 3. Install the new turn signal/security module (TSSM) (7), Hands Free Security Module (HFSM) (1) or BCM (9, 11) from this kit, following the instructions in the service manual. Configure the Trike or sidecar TSSM, HFSM or BCM to “Side Car Enabled” using Digital Technician. 4. Install the Hands Free Security Module (HFSM) Antenna and antenna mount (6) if necessary, using the service manual instructions. Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) ACTUATION 1. See a Harley-Davidson dealer to activate the key fob to the TSSM, HFSM or BCM. NOTE You can activate the TSSM fob by referring to the procedure in the electrical diagnostic manual. TRIKE AND SIDECAR CONFIGURATION (FL TOURING MODELS ONLY) Only Touring Harley-Davidson Motorcycles are suitable for sidecar use. Consult a Harley-Davidson dealer. Use of motorcycles other than Touring models with sidecars could result in death or serious injury. (00040a) NOTES FL Touring Models equipped with TLE/TLE-Ultra Sidecar require the installation of a Bank Angle Sensor (88115-03). Failure to install and configure a Bank Angle Sensor may result in death or serious injury. Sidecar and Trike configuration of the security system requires the use of a Digital Technician. Consult your Harley-Davidson dealer or the sidecar or Trike service manual for complete details. On vehicles equipped with a sidecar, the security system must be reconfigured from the default solo vehicle setting to the sidecar setting

Incoming search terms:

HARLEY DAVIDSON RIDER BACKREST MOUNTING HARDWARE KIT INSTALLATION INTSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
INSTALLATION 1. Remove seat according to the instructions in the service manual. 2. Remove the ECM caddy/battery cover by removing two screws. 3. See Figure 1 and Figure 2 for the mounting locations of the brackets. NOTE Some seats may limit the fore/aft mounting location of the backrest bracket. 4. See Figure 3 and Table 1. Remove plastic protective cap and locknut from stud. Leave the small plastic washer in place or the stud plate will fall out. With the backrest mounting bracket tab facing forward, attach the backrest mounting bracket (1) to stud plate with stock locknuts from the stud plate. 5. Tighten locknuts to 5-8 ft-lbs (6.8-10.8 Nm) . 6. Attach the front mounting bracket (6) to the frame cross- member using using two flange screws (8) and flange nuts (7). Tighten screws to 72 in-lbs (8.1 Nm) . 7. Attach the bracket support (2) to the front mounting bracket (6) with screw (8) and nut (7). 8. Install screw (5) and nut (9) to bracket support and backrest tab and tighten to 15 ft-lbs (20.3 Nm) . 1 2 is05475 1. Backrest mounting bracket 2. Front mounting bracket Figure 1. Bracket Mounting Locations 3 2 1 is05476 1. Backrest mounting bracket 2. Front mounting bracket 3. Bracket support Figure 2. Backrest mounted After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) -J04733 1 of 2
9. Install the ECM caddy/battery cover using two screws previously removed and tighten to 6-8 ft-lbs (8.1-10.8 Nm) . 10. Install seat according to service manual instructions. 11. Hold slit between rider and passenger seat open. On rider backrest, compress backrest rods and spring. Insert rods into backrest mounting bracket. Backrest Pad Adjustment 1. Adjust fore/aft position of backrest pad. Use 3/16 inch hex wrench to adjust set screw that is accessible through eyelet opening on rear of pad. If possible, do not remove set screw because it is difficult to install.

Incoming search terms:

HARLEY DAVIDSON FLST REPLACEMENT WINDSHIELD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION 1. See Figure 1. Remove stock windshield. 2. Remove all hardware that secures mounting brackets to windshield. The nine screws must be removed with a T- 27 TORX® screwdriver. Save all hardware and brackets for installing new windshield. 3. Remove all old tape from brackets and apply new tape (1, 2) from kit onto brackets. Align holes in tape with holes in brackets. Do not exceed recommended torque when installing mounting screws. Damage to windshield can result. (00385a) 4. Install all brackets. Tighten all screws and acorn nuts to 48-60 in-lbs (5.4 to 6.8 Nm) . 5. Install windshield (3) on motorcycle CARE AND CLEANING Polycarbonate windscreens/windshields require proper attention and care to maintain. Failure to maintain polycarbonate properly can result in damage to the windscreen/windshield. (00483d) •Do not use benzene, paint thinner, gasoline or any other type of harsh cleaner on the windscreen/windshield. Doing so will damage the surface. •Do not clean Lexan® polycarbonate in hot sun or high temperature. •Powdered, abrasive or alkaline cleanser will damage the windscreen/windshield. •Never scrape the windshield with a razor blade or other sharp instruments, as permanent damage will result. •Sunlight reflections off of the inside curvature of a windscreen/windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windscreen/windshield to avoid reflections. •Do not use benzene, paint thinner, gasoline or any other cleaning agents on the rubber bushings. Doing so will damage the bushing surfaces. Do not use harsh chemicals including rain sheeting products on Harley-Davidson windshields. They can cause dulling or hazing. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant (00231a) NOTES Covering the windshield with a clean, wet cloth for about 15 minutes before washing will make dried bug removal easier. Harley-Davidson Windshield Water Repellent Treatment Part Number 99841-01 is approved for use on Harley-Davidson Lexan windshields

Incoming search terms:

HARLEY DAVIDSON SPORSTER, DYNA AND SOFTAIL LICENSE / TURN SIGNAL RELOCATOR INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Remove the license plate. Remove the license plate mounting bracket from the fender. Remove the two screws from the tail light lens and pull the light outward, unplug the wire connector and set aside. Unplug the turn signal wire connectors from the tail light base and push them out thru the hole in the fender. Looking up underneath the rear fender remove the wires from the clips that secure them to the bottom side of the fender. Cut the wires 2″ from the plugs as shown in photo 1. 2. Unscrew the signal housings from their mounting stems while rotating the wires on the inside of the fender so as not to twist them off while unscrewing the signal from the stem. Remove the signals pushing the wires thru from the inside while pulling the signal outward. Remove the nuts from the backside of the fender that secure the stems and remove the stems. 3. Assemble the license/turn signal bracket, turn signals. Place the smaller reinforcing bracket inside the license plate bracket. Locate the two supplied 5/16″ X 1″ bolts with holes drilled thru the center and the two supplied 5/16″ long spacers. Place the bolts thru the brackets from the inside, threads facing outward followed by the spacers. Thread the wires of the signals thru the bolts and thread the bolts into the signals and snug the bolts. 4. Mounting the LED lights a. Locate the supplied LED tail/brake lights. NOTE: this license plate holder is designed for the new U.S. standardized 7″ wide license plate. If you have an old style wider plate call us at the phone number below and we will send you a separate set of chrome brackets to work with your larger plate at no charge. b. Install the lights as shown in photos 2 & 3. Thread the wires of the LED lights thru the lower holes in the license bracket, peel the adhesive backing and press them firmly in place. Cut the wires off at about 18″ long. c. Install the license plate bracket with signals and LED lights onto the rear fender as shown in photos 2 & 3. Place the two supplied 1/4″ X 1″ flat head screws thru the license plate mounting block. Notice that the thicker half of the mounting block goes toward the top of the fender. d. Next route all the wires from the right turn signal and LED into the slot or notch on the backside of the mounting block followed by the rubber mounting gasket. Install the two nuts from the underside of the fender (Removed from the original license bracket.) onto the two flat head screws and snug them being sure the wires are all in the slot of the mounting block. Run all of the signal and LED wires thru the hole in the fender to the left of the mounting block. e. Install the license plate assembly onto the mounting block using the two supplied 1/4″ X 1/2″ flat head screws. Check the slack from all the wires and again be sure the wires are not pinched between the mounting block and the fender. Tighten all four flat head screws securely. Align the turn signals and tighten their mounting bolts securely.

Incoming search terms:

HARLEY DAVIDSON FL ADJUSTABLE RIDER BACKREST MOUNTING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
REMOVAL 1. Remove existing seat and grab strap (if equipped) following instructions in the service manual. 2. Refer to the service manual and remove the left side cover and battery. 3. See Figure 5. Pull plastic spark plug wire clip out of the hole in the frame plate at the location where the adjustment handle bracket is going to mount. Discard plastic hose clip. 4. Remove the mid-frame air deflector upper left mounting bolt and washer. Save for installation. 5. If equipped with a grab rail: See Figure 1. Remove grab rail screws (1) and discard. 6. Remove wire harness retention clip located above the bank angle sensor. Discard clip. 7. Remove screws (3) holding the bank angle sensor (4). 1 3 2 4 is06104 1. Grab rail screw (2) 2. Grab rail 3. Bank angle sensor screw (2) 4. Bank angle sensor Figure 1. Remove Bank Angle Sensor Screws INSTALLATION 1. See Figure 2. Install clip nut (1) in mounting hole (2). Align the clip nut hole with alignment hole (3). Follow the instructions included with the Mid-Frame Air Deflector Kit to install the four self-clinching special nuts. 2. Move the electrical connector so that the backrest mounting base does not interfere with it. 3. See Figure 3. Install mounting bracket (8) to mounting base (4) with screw (6) and flange nut (7). Tighten screw to 72-96 in-lbs (8-11 Nm) . NOTE Only use the specified screw to install the mounting bracket to the bank angle sensor. 4. Secure the mounting bracket (8) to the bank angle sensor bracket with 1/4-20 x 5/8 inch screws (5). 5. If installing grab strap (9), install backrest mounting base and grab strap with screws (1) and washers (2). If grab rail is installed, install backrest mounting base with screws (1) and washers (2)

HARLEY DAVIDSON ADVANCED AUDIO CB RADIO KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
2006 models: communication switch 77173-06 2007 models: communication switch 77173-07 2008 models: communication switch 77173-08 FLHT models will require prior installation of: •Advanced Audio AM/ FM/ CD Radio Kit (76412-06) •AM/ FM Antenna Kit (76325-06 or 76317-06) Unless one has already been fitted as part of another Advanced Audio kit installation: 2006-2007 FLHX models will require the separate purchase of: •fuel tank console (61270-98A), •tank console gasket (71294-89), •a button-head screw (3652), •nut (7964) •clip (10103 and 10120). •tank pod mounting screws (2462) quantity 3 •FLHT trim piece (52447-96) and cb pod trim badge 2008 FLHX models: •fuel tank console (61270-08) •clips (10103 and 10120) NOTE The console screws, fuel door, gasket, mounting bracket will all need to be reused. FLTR models will require the separate purchase of: •a Console Pod Assembly (77136-03), and •three pan-head screws (2462). NOTE See a Harley-Davidson dealer for availability of optional decorative inserts for the Console Pod Assembly. ALL models will require the additional purchase of: •a Non-Ultra Overlay Harness (70169-06), and EITHER : •a Premium Stereo Helmet Headset (77147-98) OR a Hand-Held CB Microphone Kit (76312-98), All of these items are available from a Harley-Davidson Dealer. If two modules are already installed on top of the radio, two Dual-LockTM mounts, (76434-06), will be needed. Models WITHOUT a Tour-Pak installed will require the additional purchase of a Frame Mount CB Antenna Kit (76415- 06). Models WITH a Tour-Pak installed will require the additional purchase of a Tour-Pak Mount CB Antenna Kit (76414-06). All of these items are available from a Harley-Davidson Dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Electrical Overload It is possible to overload your motorcycle’s charging system by adding too many electrical accessories. If your combined electrical accessories operating at any one time consume more electrical current than your vehicle’s charging system can produce, the electrical consumption can discharge the battery and cause vehicle electrical system damage. See a Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories, or for necessary wiring changes. (00211b)

Incoming search terms:

1996+ HARLEY DAVIDSON FLH INNER AND OUTTER FAIRING MOUNT FOR HONDA VTX 1300 installation

0

Filed Under (Tips and Review) by admin on 09-04-2012

download
This mount was made to attach the HD FLH assembled fairing to the 4 fork mounting points on the VTX 1300 using the Memphis Shades mounts. This allows use of the MS allen wrench to quickly remove the fairing if needed. You will have to make or buy a headlight extension. Has to be done first. I used a 5″ x 5″ x .5″ piece of aluminum stock and made one to bump the headlight out 4″. There will be some trimming and relocating of brackets. And you’ll have to buy longer bolts to mount everything correctly. Get the headlight squared away first, then do the fairing. Take a length of 1″ aluminum angle stock and cut two 17″ pieces from it. These will be the uprights for the “H” brace. Measure 5.5″ from the bottom of one piece and center punch for a hole. Drill a large enough hole to slip over the MS mounting hardware on the forks. Start at about ½” bit and notch out as necessary. Center of this hole has to be 5.5″ from the absolute bottom of the angle iron. In the same location, drill out another notch for the bottom mounting point. A drill press is handy for these modifications and you can hog out the mounting notches with a file, dremmel, etc., until they fit. Do the same for the other length of 1″ angle stock but make sure it is a mirror image of the first one. Test fit these by mounting them to the MS fork brackets using the MS bracket hardware. Bottom notch goes in first, then the top notch. I epoxied the back “nuts” of the mounting hardware to the fork mounting brackets. It keeps it in place when you’re taking the fairing on and off the bike. On the top mounting points, I epoxied a washer with one side ground flat to the bolt’s mounting ferule. This allowed better contact between the H brace and the fork mounting bracket. Didn’t want that fairing falling off. Adjust as necessary and after the test fit, remove.

Incoming search terms:

HARLEY DAVIDSON XL SPRING SEAT MOUNTING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION 1. Refer to service manual and remove the existing seat, seat post, washer and screw. Do not remove grommet or T-spacer from rear fender. Save the washer and screw for later installation. 2. See Figure 1. Clean the frame surface where the hook- and-loop strip will be attached with a 1:1 mixture of isopropyl alcohol and water. Let it dry completely. 3. Install the frame cover to the frame as follows: a. Remove the loop side of the hook-and-loop (3) from the bottom of the frame cover (1). b. Remove the protective tape from the hook-and-loop strip and attach it to the frame as shown. Wrap it under the frame or trim excess length, if necessary. c. Orient the frame cover so that it covers the seat pan and secure the cover to the frame with the hook-and- loop strips. 4. See Figure 3. Install two springs (2) to the mounting bracket (1), oriented as shown, with screws (3). Tighten screws to 25-30 ft-lbs (34-41 Nm) . 5. See Figure 3. Install mounting bracket to frame tab a. Install mounting bracket (1) over frame tab. Orient it so that the two retaining tabs on the mounting bracket will hold down and be fully seated on the frame cover. b. Secure mounting bracket with screw (B), washer (C) and nut (4). Do not tighten. c. Center the frame cover and mounting bracket to the motorcycle frame. d. Tighten mounting bracket screw and nut to 15-20 ft- lbs (20-27 Nm) . 6. Install seat pivot bracket (15), washers (14) and screws (13) to the seat. Tighten screws to 48-72 in-lbs (5.5-8.0 Nm) . 7. Remove the rear fuel tank mounting screw, washers, nut and thread protector. Save washers for later installation

Harley-Davidson Auxiliary LED Brake Light Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-03-2012

download
If you are mounting the lighthead on a Harley-Davidson® motorcycle box, use the existing wire hole. Drill your mounting holes so the wire hole (located very close to the mounting hole in the lighthead) will line up with the wires, but not interfere with the mounting holes. Since the lighthead can mount to any vehicle, this manual will cover mounting to a generic location. 1. Mark the location of the 2 mounting holes onto the mounting surface using the dimensions shown above, or remove the lens and use it as a template. Always check behind the mounting surface to be sure you will not interfere with any other vehicle components. 2. Drill the 2 mounting holes using a drill sized for a #6 sheet metal screw, then drill the 9/32″ wire access hole 5/16″ away from the mounting hole as shown. 3. Feed the wires through the wire hole then secure the brake light to the mounting surface with the supplied mounting hardware. 4. Wire the lighthead into your existing brake light wiring, matching the lighthead wire colors to the vehicle wire colors (see “Wiring”). WARNING! All customer supplied wires that connect to the positive terminal of the battery must be sized to supply at least 125% of the maximum operating current and FUSED at the battery to carry that load. DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT!

HARLEY DAVIDSON BILLET HEADLAMP WITH SHORT/ TALL MOUNTS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Kit 68593-06 is a 5-3/4 inch headlamp and kit 69851-06 is a 4-1/2 inch headlamp. Both kits will fit the models listed in Table 1. Table 1. Short and Tall Mount Kits Models Kits 1984-1999 FXSTC, 1998- Later FXST/B, and 2000-Later FXSTD; 1994-2005 FXDWG Short Mount Kit 68595-06 1996-Later XL 1200C and 1998-Later XL 883C; All 2006 Dyna Models; 1999-2000 FXR2/3/4 Tall Mount Kit 69611-06 Additional Parts Required This kit also requires the separate purchase of a Short or Tall Mounting Kit 68595-06 or 69611-06 for your model motorcycle, and can be purchased from a Harley-Davidson dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 21, Table 2 and Figure 22, Table 3. REMOVAL Remove Headlamp and Mounting Bracket for Softail Models To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. 2. Remove fuel tank. Refer to FUEL TANK in Service Manual. 3. Disconnect 4-place headlamp connector [38] from main wire harness. Headlamp connector is located under fuel tank on left side. 8 5 7 5 6 2 1 3 4 is01835 1. Screw 2. Washer 3. Nut 4. Lockwasher 5. Washer (2) 6. Screw 7. Mounting block 8. Headlamp assembly Figure 1. Softail and Dyna Headlamp Assembly with Mount (except FXSTD) NOTE All Softails (except FXSTD) complete steps 4 through 6. For FXSTD models complete steps 7 through 9 4. All Softails (except FXSTD): See Figure 1. Remove screw (1) and washer (2) from stem and bracket. Discard screw but save washer for later use. 5. Remove and discard mounting block (7) and headlamp assembly (8). 6. FXSTD models: See Figure 2. Remove screw (1) and washer (2) from stem and bracket. Save screw and washer for later use. 7. Remove and discard nut (3), washers (4), and screw (5). 8. Remove and discard mounting block (6) and headlamp assembly (7). 7 3 4 2 1 4 6 5 is01838 1. Screw 2. Washer 3. Acorn nut 4. Washer (2) 5. Screw 6. Mounting block 7. Headlamp assembly Figure 2. FXSTD Headlamp Assembly with Mount Remove Headlamp and Mounting Bracket for Dyna Models 1. Remove seat following the instructions in the Service Manual. 2. Disconnect negative (-) battery cable. 3. Remove fuel tank. Refer to FUEL TANK in Service Manual. 2 1 is01750 1. Cable strap 2. Wire harness Figure 3. Dyna Service Loop (2005-Earlier) 4. 2005-Earlier FXDWG: See Figures 3 and 4. Remove plug on right side of top frame tube. At service loop, remove cable clip and push wire harness into top frame tube. Pull connector out from hole on right side of tube. 2006-Later FXD: See Figure 5. Remove cover under top frame tube, then pull connector out from opening under tube. 5. Disconnect 4-place headlamp connector [38] from main wire harness

Incoming search terms:

Incoming search terms: