harley davidson speaker switch

You search Auto repair manual PDF harley davidson speaker switch, if there are search results will appear below. If search results do not exist, please search by others keyword.



  harley davidson speaker switch Direct Download speed 5282 Kb/s

  harley davidson speaker switch Full Version speed 6162 Kb/s



Harley-Davidson CHROME HANDLEBAR SWITCH CAP KITS installation and REMOVAL manual

0

Filed Under (Harley Davidson) by admin on 09-03-2012

download
1. Open or remove seat according to the instructions in the Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove left and right-hand switch housing assemblies. Refer to HANDLEBAR SWITCHES in Service Manual. NOTE It is not necessary to disconnect the switch wiring to replace the switch caps. 4. Remove individual switches from switch housing. Refer to SWITCH REPAIR/REPLACEMENT in Service Manual. INSTALLATION Upper Housing Switches 1. For HORN and START switch caps, release torsion spring leg from hole in switch cap tab. Take note of how the spring is installed. The other leg of the spring can remain in the switch bracket hole. 2. See Figure 1 and Figure 5. Carefully pry stock black switch cap up off the splined actuator shaft (2) on left side of switch. -J02633 1 of 5 5 2 1 1 3 4 is 01405 1. Switch cap installed correctly 2. Switch cap removal from splined shaft 3. Switch cap removal from pivot pin 4. Switch cap installation onto pivot pin 5. Switch cap installation onto spined shaft Figure 1. Switch Cap Removal and Replacement 3. Pry the switch cap up and away from pivot pin (3) on right side of switch, and remove cap. NOTE Use the clear protective cover film to protect the chrome surface of the switch caps during installation. Remove the film after the installation is complete. 4. See Figure 5. Select proper chrome replacement switch cap from kit. 5. See Figure 1. Place cap onto switch, angling the hole on right side over pivot pin (4) on switch. 6. Carefully press switch cap down onto splined actuator shaft (5), rocking and moving the cap until shaft snaps into place in splined hole. 7. For HORN and START switch caps, insert torsion spring leg into hole in switch cap tab. 8. Toggle switch back and forth, checking for proper opera- tion. Turn Signal Switches 1. See Figure 1 and Figure 5. Carefully pry stock black switch cap up off the splined actuator shaft (2) on switch. 2. Pry the switch cap up and away from pivot pin (3) on switch, and remove cap. 3. Select proper chrome replacement switch cap from kit. Peel a clear protective installation cover from the sheet and place it over the surface of the cap. 4. See Figure 1. Place cap onto switch, angling the hole on top over pivot pin (4) on switch. 5. Carefully press switch cap onto splined actuator shaft (5), rocking and moving the cap until shaft snaps into place in splined hole. 6. Toggle switch back and forth, checking for proper opera- tion.

Incoming search terms:

HARLEY DAVIDSON VRSC FUEL TANK SIDE COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
INSTALLATION 1. Note the left and right areas on frame where the covers will be installed. Using a 50/50 mixture of isopropyl alcohol and water, thoroughly clean the frame tubes surrounding the fuel cell on the left and right sides. Let dry completely. 2. Unlock and open seat. NOTE Loosening the ignition/light switch screw (in the following step) will allow much easier alignment of the ignition/light switch cover and ignition/light switch during installation. 3. See Figure 1. At area inside of frame rail just above the ignition/light switch housing, loosen the ignition/light switch screw just enough to allow the ignition/switch switch to move slightly from side to side and up and down. Do not completely remove screw 4. See Figure 4. Obtain the right side cover bracket (ignition/light switch side) from kit. 5. Remove the strips protecting the adhesive at all of the raised sections on the cover. 1 2 is 02045 1. Ignition/Light Switch Screw 2. Ignition/Light Switch Figure 1. Loosen Ignition Switch Assembly 6. See Figure 2. Carefully align the right side cover between the three frame tubes. Beginning with the left portion of the cover, press the cover between the upper and lower frame tubes until the raised portions of cover (with adhesive) begin to snap into place. While carefully aligning the right portion of the cover, move the ignition/light switch as necessary until centered within hole in cover, then firmly press into place. Adjust ignition/light switch until the switch is centered within cover. Make sure all raised locations (with adhesive) are firmly contacting the upper and lower frame tubes and that cushion rests against front vertical frame tube. 7. See Figure 1. Tighten the ignition switch screw to 6-10 Nm (53-88 in-lbs ) . NOTE The right side (ignition/light) switch cover surface can be damaged by the key fob (from vibration) when the key is in the ignition and the bike is running. You can either remove the key fob so it does not damage the cover surface, or you can install the plastic clear sheet (included in kit) onto the side cover for protection. 8. If desired, perform the following to install the plastic clear cover onto the ignition/light switch cover. a. Obtain the plastic (rhino) sheet and hold up to the switch cover to determine proper orientation and spacing. b. Carefully peel the adhesive backing from the plastic sheet and position onto the cover. Use a wet sponge, and working out from the center, rub out any bubbles or overlapped areas under the sheet. Allow to dry completely.

Harley-Davidson Vacuum Operated Switch Kit Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 24-03-2012

download
1. Turn off the ignition switch and disconnect the battery ground cable before proceeding. 2. For applications with Harley-Davidson OE ignition modules, simply replace the existing OE VOES switch with the new Twin Tec switch. Use the supplied crimp terminals to connect the new switch in place of the old switch. The wiring is not polarity sensitive and the two wires from the new switch can be interchanged. 3. For Twin Tec ignitions, refer to the installation instructions supplied with the ignition module for VOES switch hookup. Use the supplied crimp terminals to connect the new switch. The wiring is not polarity sensitive and the two wires from the new switch can be interchanged. 4. Reconnect the battery ground cable when you have completed the installation

HARLEY DAVIDSON ADVANCED AUDIO CB RADIO KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
2006 models: communication switch 77173-06 2007 models: communication switch 77173-07 2008 models: communication switch 77173-08 FLHT models will require prior installation of: •Advanced Audio AM/ FM/ CD Radio Kit (76412-06) •AM/ FM Antenna Kit (76325-06 or 76317-06) Unless one has already been fitted as part of another Advanced Audio kit installation: 2006-2007 FLHX models will require the separate purchase of: •fuel tank console (61270-98A), •tank console gasket (71294-89), •a button-head screw (3652), •nut (7964) •clip (10103 and 10120). •tank pod mounting screws (2462) quantity 3 •FLHT trim piece (52447-96) and cb pod trim badge 2008 FLHX models: •fuel tank console (61270-08) •clips (10103 and 10120) NOTE The console screws, fuel door, gasket, mounting bracket will all need to be reused. FLTR models will require the separate purchase of: •a Console Pod Assembly (77136-03), and •three pan-head screws (2462). NOTE See a Harley-Davidson dealer for availability of optional decorative inserts for the Console Pod Assembly. ALL models will require the additional purchase of: •a Non-Ultra Overlay Harness (70169-06), and EITHER : •a Premium Stereo Helmet Headset (77147-98) OR a Hand-Held CB Microphone Kit (76312-98), All of these items are available from a Harley-Davidson Dealer. If two modules are already installed on top of the radio, two Dual-LockTM mounts, (76434-06), will be needed. Models WITHOUT a Tour-Pak installed will require the additional purchase of a Frame Mount CB Antenna Kit (76415- 06). Models WITH a Tour-Pak installed will require the additional purchase of a Tour-Pak Mount CB Antenna Kit (76414-06). All of these items are available from a Harley-Davidson Dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Electrical Overload It is possible to overload your motorcycle’s charging system by adding too many electrical accessories. If your combined electrical accessories operating at any one time consume more electrical current than your vehicle’s charging system can produce, the electrical consumption can discharge the battery and cause vehicle electrical system damage. See a Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories, or for necessary wiring changes. (00211b)

Incoming search terms:

HARLEY DAVIDSON CHROME ON/OFF SWITCH CAP KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION Models WITH maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. Models WITHOUT maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. 1 2 is0771a 1. Auxiliary accessory housing cover 2. Cover screw (2) Figure 1. Auxiliary Accessory Housing 2. ALL models: If the Auxiliary Accessory Housing Kit and the Rocker Switch(es) ARE NOT already installed on the motorcycle handlebar: a. Proceed to Step 3 of these instructions. Install a chrome switch cap onto each switch before installing the Auxiliary Accessory Housing Kit onto the vehicle. If the Auxiliary Accessory Housing IS already installed on the motorcycle handlebar: a. See Figure 1. Using a T-25 TORX® driver, remove the two screws (2) retaining the Auxiliary Accessory Housing cover (1), and remove the cover. b. See Figure 2. Remove the switch mounting bracket, along with any attached switch(es) and accessories, from the switch housing. Note: it is not necessary to remove the switch from the mounting bracket, or to disconnect the switch wiring to replace the switch caps

HARLEY DAVIDSON FLAME HANDLEBAR GRIPS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
REMOVE AND INSTALL THE LEFT GRIP 1. See Figure 1. Using a T27 TORX® drive head, remove the two screws with flat washers securing the handebar clamp (3) to the clutch lever bracket. Remove the clamp and position the clutch hand lever assembly away from the handlebar 2. Using a T25 TORX® drive head, loosen but do not remove the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left handlebar grip if so equipped. Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) NOTE Make sure that the handlebar surface and the inside of the grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. 4. Position the new left grip (4) so the larger flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Using a T27 TORX® drive head, tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lbs (6.8-9 Nm) . 9. Using a T25 TORX® drive head, tighten first the lower, then the upper switch housing screws to 35-45 in-lbs (4- 5.4 Nm) . 5 3 1 1 4 2 2 is00735 1. Switch housing screws 2. Grooves 3. Handlebar clamp 4. Left handlebar grip 5. Larger flange Figure 1. Left Handlebar Switch Housing REMOVE AND INSTALL THE RIGHT GRIP NOTE Right handlebar switch removal requires a Service Manual for your model and year of motorcycle. A Service Manual can be purchased from your Harley-Davidson Dealer. 1. Refer to the RIGHT HANDLEBAR SWITCH section of the Service Manual for removal of the switch housing assembly. This is necessary to access the throttle cables. 2. Refer to the THROTTLE CONTROL section of the Service Manual to disconnect the throttle cables and remove the existing right grip/throttle sleeve assembly. After removal, make sure that the handlebar end is clean and smooth. 3. Follow instructions in the Service Manual to install the new right grip/throttle sleeve to the handlebar and connect the throttle cables. 4. Verify that the right grip/throttle sleeve rotates and returns freely and does not bind on the handlebar or switch housing.

Incoming search terms:

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/ IDLE CABLE KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be placed into the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 4. Remove the right upper and lower switch housing screws INSTALLATION Throttle and Idle Cable Installation 1. See Figure 3. Apply graphite lightly to the throttle grip inside the switch housing and on the throttle end of the handlebar. NOTE The throttle control cable has a larger diameter retaining ring crimped to the cable end than does the idle control cable. For assembly, apply a drop of light oil on the retaining rings of the crimped inserts. 2. See Figure 7. Push the throttle cable housing and retaining ring into the larger hole of the switch housing, located in front of the tension adjuster screw. 3. Push the idle cable housing and retaining ring into the smaller hole of the switch housing, located behind the tension adjuster screw. 4. Push the throttle and idle control cable housings into the lower switch housing until each snaps into place. NOTE For models not equipped with factory-installed cruise control, if the friction shoe has fallen out or become dislodged, install the shoe with the concave side facing up and position it so the pin hole is over the point of the adjuster screw. 5. Push the throttle control grip over the end of the right handlebar until it bottoms against the closed end. Rotate the grip until the ferrule notches are at the top. To prevent binding, pull the grip back about 0.12 inch (3.2 mm). 6. See Figure 3. Position the lower switch housing beneath the throttle control grip. Install two brass ferrules (Item 3, Figure 11) from this kit onto cables, seating the ferrules in their respective notches on the throttle control grip. The cables must be captured in the grooves molded into the grip. 7. Position the upper switch housing over the handlebar and lower switch housing. Route the wire harness conduit through the depression at the bottom of the handlebar. 8. Tighten the upper and lower switch housing screws finger- tight. 9. Position the brake lever/master cylinder assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the top of the brake lever bracket. 10. Align the holes in the handlebar clamp with those in the master cylinder housing and tighten the lower screw and flat washer finger-tight. Position for rider comfort. Beginning with the top screw, tighten the screws to 60-80 in-lbs (6.8-9.0 Nm)

Incoming search terms:

HARLEY DAVIDSON BOOM! AUDIO MUSIC AND INTERCOM KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
Intercom system flash (H-D Part No. 76441-06DT) Non-Ultra Overlay Harness (H-D Part No. 70169-06) NOTE For a more integrated appearance of the rider headset connector, the console may be replaced using an Ultra Classic Electra Glide console and/or console pod. See FLHTCU parts manual for applicable parts, and service manual for installation instructions. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet refers to service manual information. A service manual for this year/model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 7 and Table 2. REMOVAL 1. Refer to the service manual and remove the following: a. Main fuse. b. Outer fairing. c. Seat. d. Fuel tank and console. e. Inner fairing cap. f. Wire trough cover. g. Left hand control. h. Left side saddlebag. INSTALLATION Install Switch Housing on Passenger Headset Harness 1. See Figure 1. Install push-to-talk switch housing (2) to passenger headset plug housing (3), included as part of passenger headset wire harness (see Figure 7, Item 6). 2. Position the switch housing so the knob is located close to the flip cap on the passenger headset connector. 3. Install self-tapping screws (1) to the switch housing but do not fully tighten at this time. Location adjustment may be required based on the motorcycle model, seats and accessories installed on the vehicle Secure Headset Connector and Switch Housing 1. 2006-2008 FLHX, FLTR, FLHT/C models: For motorcycles WITHOUT docking hardware, See Figure 7. Use the fender support cover fastener to install the smaller P-clamp (11) from the kit. For vehicles WITH docking hardware, use the front docking point fastener. Install the smaller P-clamp (11) between the outside face of the docking point behind the screw and washer. 2009-later FLHX, FLTR, FLHT/C models: For motorcycles WITHOUT docking hardware, see Figure 2. Use the threaded hole in the frame using screw (4), washer (3), spacer (2) and the smaller P-clamp (5) from the kit. For motorcycles WITH docking hardware, use the docking point shown in Figure 3. Install the smaller P-clamp from the kit to the outer end of the docking point using the docking point washer and screw. 2009-later Trike models without the Tour-Pak (FLHXXX): See Figure 4. The headset/switch assembly (1) will be secured to the frame at the location shown using the 1/2- 13 screw (3) and the larger P-clamp (2) from the kit. 2. For ALL models: Once the position of the PTT/VOL switch has been established, securely tighten the self-tapping screws installed to the switch housing earlier.

2010 Harley-Davidson FLHR Road King front and rear 4-piston braking system Installation

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
in Vivid Black with blue and silver pinstripes, six-speed. Air-cooled, Twin Cam 96™ engine with Electronic Sequential Port Fuel Injection (ESPFI), ABS, security system, cast wheels with independent front and rear 4-piston braking system. Motorcycle generously donated by Harley-Davidson Motor Company Police & Fleet Sales. MSRP excludes all taxes title/documentary fees, registration, tags, dealer prep, labor and installation charges, insurance, optional equipment and accessories, certificate of compliance or non-compliance fees, and finance charges. Delivery must be coordinated through Rockville Harley-Davidson by November 30, 2010. Winner is responsible for any applicable fees above. 6,000 tickets printed. Odds of winning are 1:6,000. Ticket holder need not be present to win. Licensed by the D.C. Lottery and Charitable Games Control Board. Must be 18 years or older to win. No substitutes, return for cash, or other models. As per IRS tax code, amounts paid for chances in a raffle do not qualify as a deductible charitable contribution. Taxes on prizes are the responsibility of the winner. Harley-Davidson is proud to be a sponsor of the National Law Enforcement Officers Memorial Fund. Harley-Davidson Motor Company is a prize provider only, and Harley-Davidson, Inc., and Harley-Davidson Motor Company have no responsibility regarding conduct or administration of the raffle.

Incoming search terms:

HARLEY DAVIDSON SECURITY SYSTEM KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
FL Touring models equipped with a TLE/ TLE Ultra Sidecar will require the additional installation of a Bank Angle Switch Kit (88115-03) and is available for separate purchase. See a Harley-Davidson dealer.INSTALLATION 1. Remove the original equipment (OE) Turn Signal Module (TSM) or Body Control Module (BCM) following the instructions in the service manual. 2. Install the Bank Angle Sensor (BAS) on sidecar vehicles. 3. Install the new turn signal/security module (TSSM) (7), Hands Free Security Module (HFSM) (1) or BCM (9, 11) from this kit, following the instructions in the service manual. Configure the Trike or sidecar TSSM, HFSM or BCM to “Side Car Enabled” using Digital Technician. 4. Install the Hands Free Security Module (HFSM) Antenna and antenna mount (6) if necessary, using the service manual instructions. Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) ACTUATION 1. See a Harley-Davidson dealer to activate the key fob to the TSSM, HFSM or BCM. NOTE You can activate the TSSM fob by referring to the procedure in the electrical diagnostic manual. TRIKE AND SIDECAR CONFIGURATION (FL TOURING MODELS ONLY) Only Touring Harley-Davidson Motorcycles are suitable for sidecar use. Consult a Harley-Davidson dealer. Use of motorcycles other than Touring models with sidecars could result in death or serious injury. (00040a) NOTES FL Touring Models equipped with TLE/TLE-Ultra Sidecar require the installation of a Bank Angle Sensor (88115-03). Failure to install and configure a Bank Angle Sensor may result in death or serious injury. Sidecar and Trike configuration of the security system requires the use of a Digital Technician. Consult your Harley-Davidson dealer or the sidecar or Trike service manual for complete details. On vehicles equipped with a sidecar, the security system must be reconfigured from the default solo vehicle setting to the sidecar setting

Incoming search terms:

Incoming search terms: