harley davidson tour pack quick release

You search Auto repair manual PDF harley davidson tour pack quick release, if there are search results will appear below. If search results do not exist, please search by others keyword.



  harley davidson tour pack quick release Direct Download speed 5282 Kb/s

  harley davidson tour pack quick release Full Version speed 6162 Kb/s



HARLEY DAVIDSON ULTRA CLASSIC AND ELECTRA GLIDE CLASSIC TOUR PACK ADJUSTMENT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
1. Open the Tour Pack and remove all of the contents. 2. Remove map bag and inner pack liner. Pack liner comes out quite easily once map bag is removed. 3. Remove the 4 bolts inside the tour pack that are located on top of the metal support plate that hold the tour pack to the luggage rack. Have your assistant hold the pack in place before removing the last bolt. 4. Gently tip the tour pack forward to expose the supporting luggage rack under the pack. 5. While your assistant holds the pack up, place the two adjusting bars on top of the supporting luggage rack. Use the 4 flat head screws supplied with the kit to mount the bars snugly to the support rack (see fig. 1). 6. Reposition the tour pack over the threaded holes in the adjusting bars at the 2″ or 3″ position and bolt it in place snugly (see fig. 2). 7. Replace the trunk liner and map case and the installation is complete

Incoming search terms:

HARLEY DAVIDSON TOURING DETACHABLE TOUR-PAK RACK INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION NOTE See Figure 3. When installing Tour-Pak to Rack in the following Steps, note that holes on Rack provide two positions for mounting Tour-Pak in desired location. 1. Place Tour-Pak on support tube and open lid. NOTE See Figure 3. In the following step, the longer bolts (6) are used for 2005 and earlier (King only) and Chopped Tour-Paks while the shorter bolts (5) are used for Leather Tour-Pak and 2006 and later King Tour-Paks. 2. See Figure 3. Obtain bolt (5 or 6), two flat washers (3), concave spacer (4) and hex lock nut (2) from kit. Align rear center hole in Tour-Pak with same hole in support tube (8). Slide bolt with flat washer through Tour-Pak, through support tube, then through concave spacer (with concave side facing support tube). At bottom of support tube, install washer (3) and nylock cap nut (2). With concavity on spacer inline with the rail, hold nut and tighten bolt until snug. 3. Obtain bolts (5 or 6), two flat washers (3), concave spacer (4) and hex lock nut (2) from kit. Align top support tube (8) with detachable tour-pak rack holes (four). Slide bolts with flat washer through Tour-Pak, through support tube, through concave spacer (with concave side facing support tube) then through rack. At bottom of detachable tour-pak rack, install washer (3) and nylock cap nut (2). With concavity on spacer inline with the rail, hold nut and tighten bolt until snug. NOTE Always install the mounting bolts from inside the Tour-Pak. If the bolts are installed upside down, then the ends of the bolts can tear the molded liner and scratch objects, such as helmets, stored inside the Tour-Pak. 4. Repeat Step 3 and install hardware to the remaining three holes in Tour-Pak and mounting rack. 5. In a crosswise pattern, alternately tighten the five bolts to 96-120 in-lbs (10.8-13.5 Nm) . Be sure that concavity on each spacer is inline with the rail and has not rotated out of position. INSTALLATION-TOUR-PAK AND RACK 1. Follow the instructions included in the docking point kit and install docking points. 2. See Figure 1. While standing behind the motorcycle, place the front Tour-Pak rack notches into the front docking points (1). Make sure the notches seat fully into the front docking points. 2 1 is04025 1. Front Docking Point 2. Rear Docking Point Figure 1. Docking Point Bracket 3. See Figure 1 and Figure 2. Position the latches over the rear docking points (2). Check to be sure the latches fit into the neck of the rear docking points as shown in figure 2. This may require some gentle squeezing or spreading of the rack

Incoming search terms:

HARLEY DAVIDSON TOUR-PAK KIT INTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION 1. Remove the rubber mat from the bottom of the Tour-Pak. 2. See Figure 1 and Table 1 to determine the proper hole configuration to attach the Tour-Pak to your luggage rack. Holes will be drilled as explained in Step 3 in the hole location for your luggage rack. Table 1. Luggage Rack and Hole Configurations Hole Configura- tion Luggage Rack C (3 holes) Stock 1997 B (4 holes) Detachable luggage rack 53107-96 A (5 holes) Luggage rack 53118-97A and luggage rack 53118-98 A (5 holes) Stock 1998 and later racks A (5 holes) Detachable Tour-Pak rack 53276-04 B (4 holes) Solo detachable Tour-Pak rack 53655-04 B (4 holes) Detachable Tour-Pak rack 53066-00B B (4 holes) Solo detachable Tour-Pak rack 53559-04A A (5 holes) Solo detachable Tour-Pak rack 53260-02 -J03631 1 of 3 B 1 A C 2 2 2 is00163 1. Front of motorcycle 2. Bottom view of Tour-Pak interior (rubber mat removed) Figure 1. Hole configurations for Tour-Pak attachment NOTE Drilling holes in Tour-Pak without wood underneath each hole site may result in the leather becoming damaged during the drilling process. 3. Place blocks of wood underneath the Tour-Pak where the holes will be drilled to prevent damage to the leather while drilling. Use the pre-drilled holes in the metal base as a guide and carefully drill the holes through the leather in the proper location using a 11/32 inch drill bit. 4. See Figure 2. For detachable luggage racks (53107- 96, 53066-00B and 53276-04): Install black cover tube to the front bar (1) of the luggage rack, as shown. This tube is used to provide a cleaner look. The black cover tube is not for use with other luggage racks. 5. Attach Tour-Pak to rack using the mounting screws provided in the Luggage Rack kit. Put bolt through from inside of Tour-Pak. Tighten screws to specifications found in the Luggage Rack kit. 6. Place the black rubber mat on the bottom of the Tour-Pak. 7. If luggage rack was removed, reattach to motorcycle according to kit instructions or Service Manual instructions

Incoming search terms:

HARLEY DAVIDSON TOUR-PAK RACK LIGHT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
INSTALLATION 1. Remove all contents from Tour-Pak®. 2. For easier installation, remove Tour-Pak rack, if installed, by removing cap screw, washers and mounting pads. 3. See Figure 1. Remove rubber plug from bottom rear rail on left side of rack. 4. See Figure 2. Use line wire feeder in kit to thread through left rear rack foot and out through the back opening of rail. 5. Attach light harness wires to line wire feeder loop. 6. Carefully pull line wire feeder and light harness wires through rack mounting foot. 7. See Figure 5 and Table 1. Apply foam pads (5) to top surface of light. 8. Secure light (1) to rack with socket head screws (4) and washers (6). 1 is05242 1. Plug Figure 1. Left Side Rack Plug 1 is05244 1. Line wire feeder Figure 2. Thread Wires Through Rack 9. Position rack/light assembly to Tour-Pak lid and route wires through lid, washer and hollow mounting bolt. 10. Attach rack/light assembly to Tour-Pak using instructions and hardware provided with rack except for use of hollow bolt from Step 9. 11. Remove Tour-Pak liner. 12. Thread wires through black vinyl conduit. 13. Ultra Classic models: Follow Steps 14 through 2114. Locate and disconnect three pin AMP connector for Tour- Pak lights. 15. See Figure 3. Attach the Y-harness (2) to the three pin male connector (1) of Tour-Pak harness. 16. Route light wires from back of Tour-Pak along left side to front. Secure conduit with adhesive clips provided in kit. 17. Trim length of light wires and conduit to reach Y-harness. 18. Refer to the Service Manual electrical appendix to install terminal pins (8) to rack light wires and install terminals to three pin housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead 19. Connect rack light to remaining Y-harness connector. 20. Replace Tour-Pak liner. 21. Check operation of Tour-Pak tail and stop light functions before operating motorcycle. 22. Classic models: See Figure 4. If necessary, drill hole in lower left bottom of Tour-Pak and install grommet. Route rack light wires through grommet. 23. Refer to the Service Manual electrical appendix to install terminal receptacle (8) to rack light wires and install terminals to three pin receptacle housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead NOTE To prevent corrosion, fill the cavities of the connectors with dielectric grease (included in kit) prior to making connections. As an additional precaution against moisture seepage into the Tour-Pak, apply silicone sealant (not included in kit) to the entrance of the light harness wire tunnel. See figure 2 for location reference. 24. Connect rack light to male connector of two connector wire harness (12) and connect to accessory connector under seat. 25. Replace Tour-Pak liner. 26. Check operation of Tour-Pak tail and stop light functions before operating motorcycle

Incoming search terms:

HARLEY DAVIDSON TOUR-PAK WALL ORGANIZER INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
This kit fits 1997 and later models equipped with King Tour- Paks INSTALLATION NOTE Maximum Wall Organizer weight capacity is 3 pounds (1.4 Kg) evenly distributed. Do not exceed tour-pak weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00401b) Tour-Paks With Molded Liner 1. Remove the two nuts that hold the pouch and liner in the Tour-Pak. Remove pouch and liner and carefully wash the inside of the Tour-Pak with warm, soapy water. Rinse and dry thoroughly. 2. Use the alcohol prep pad in the kit to thoroughly clean the interior surface of the Tour-Pak sides where fastener strips will be attached. Make sure any residue is removed, then allow Tour-Pak to dry completely. Make sure the surface is free of condensed moisture. NOTES The hook and loop fastener strips and organizer must be installed below the edge of Tour-Pak base to avoid interference with top gasket and lock. The ideal temperature range for applying the fastener strip is 70-100° F (21-38° C). Minimum application temperature is 50° F (10° C). If you attempt to apply the tape below these temperatures, the adhesive will become too firm to adhere readily. 3. See Figure 1 and Figure 2. Remove the hook and loop fastener strips from the hinged hook and loop strips. Remove the paper backing and firmly press the fastener strips into the locations (1) shown in Figure 2. The fastener strips should be located approximately 1/8 in. (3 mm) below the edge of the Tour-Pak base. 4. See Figure 1. Bend the hinged hook and loop strips (3) into shape as shown. Attach the hinged strips onto the fastener strips (2) installed in Step 3. NOTE The Tour-pak Wall Organizer installs in place of the pouch removed in Step 1, therefore the pouch will not be re-installed. 5. Reinstall the liner removed in Step 1. The hinged strips (3) will go over the top of the liner (4) as shown in Figure 1. 6. See Figure 1. Attach the organizer (5) to the hinged strips (3). Adjust the organizer’s lock cut out so that it is centered around the lock, and press the hook side of the hook and loop strips on the bottom of the organizer into place on the liner. The hook side will attach to the liner. NOTE 2006 and later Tour-Paks equipped with Passenger Backrest will have two acorn nuts at the front of the base. Remove and discard the 8 in. (200 mm) long hook and loop hinged fastener strip from the center panel. In one of the organizer pockets there will be 4 in. (100 mm) and 1-1/2 in. (38 mm) hook and loop hinged fastener strips. Install the hinged strips on the organizer center panel as shown in Figure 3. 7. Check to make sure the Tour-Pak lid closes over the organizer and the lock works without interference. Adjust as necessary. 8. Allow tape to cure (“wet-out”) for a minimum of 48 hours at 70° F (21° C) (allow extra time if temperature is below 70°). Do not place items in the Wall Organizer while adhesive is curing

HARLEY DAVIDSON PREMIUM TOUR-PAK LUGGAGE RACK KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
INSTALLATION Template Positioning (Rack Installation WITH SPOILER only) The location of the luggage rack has a direct relationship to the location of the Tour-Pak® Spoiler. The template (7) included in this kit will locate the luggage rack in the correct position for the current or future installation of a Tour-Pak Spoiler. NOTE A template is not required if installing rack without spoiler. 1. If a spoiler is already installed, or if the installation of a Tour-Pak-mounted spoiler may be desired in the future, cut the template along the appropriate line. 2. Carefully place the trimmed template on top of the Tour- Pak, aligning the edges of the template with the top surface of the Tour-Pak lid. Tape the template to the lid in the desired location. The template will help to properly locate the rack so that a spoiler may be added in the future. Rack Installation on Tour-Pak 1. ALL installations: Open the lid, and remove all loose contents from the Tour-Pak. 2. See Figure 1. Slip the mounting pads (2) onto each of the mounting bosses (B) of the luggage rack (1). NOTES Kit 53665-87: Position rack with wide upright toward rear of vehicle. Kit 91793-85: Position rack with upright toward rear of vehicle. Carefully center the rack from left to right, and position the rack squarely on the lid for best appearance. Do not mount the rack too far forward to avoid contact with the backrest pad. 3. Position the rack on the Tour-Pak lid in the desired loca- tion. 4. Carefully raise the rack, and place masking tape (A) on the Tour-Pak lid where the four mounting bosses contact the cover. 5. Lower the rack onto the tape in the location chosen in Step 3. Using a soft lead pencil on the masking tape strips, trace a circle around each mounting boss. Remove the rack, and use a ruler to mark the exact center position of each mounting boss on the tape. 6. Drill four 1/16 inch (1.5 mm) diameter pilot holes through the masking tape and Tour-Pak lid at each mounting boss center position. Use a 9/32 inch (7 mm) diameter bit to drill the finish holes. 7. Remove the masking tape

Incoming search terms:

HARLEY DAVIDSON ADVANCED AUDIO CB RADIO KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
2006 models: communication switch 77173-06 2007 models: communication switch 77173-07 2008 models: communication switch 77173-08 FLHT models will require prior installation of: •Advanced Audio AM/ FM/ CD Radio Kit (76412-06) •AM/ FM Antenna Kit (76325-06 or 76317-06) Unless one has already been fitted as part of another Advanced Audio kit installation: 2006-2007 FLHX models will require the separate purchase of: •fuel tank console (61270-98A), •tank console gasket (71294-89), •a button-head screw (3652), •nut (7964) •clip (10103 and 10120). •tank pod mounting screws (2462) quantity 3 •FLHT trim piece (52447-96) and cb pod trim badge 2008 FLHX models: •fuel tank console (61270-08) •clips (10103 and 10120) NOTE The console screws, fuel door, gasket, mounting bracket will all need to be reused. FLTR models will require the separate purchase of: •a Console Pod Assembly (77136-03), and •three pan-head screws (2462). NOTE See a Harley-Davidson dealer for availability of optional decorative inserts for the Console Pod Assembly. ALL models will require the additional purchase of: •a Non-Ultra Overlay Harness (70169-06), and EITHER : •a Premium Stereo Helmet Headset (77147-98) OR a Hand-Held CB Microphone Kit (76312-98), All of these items are available from a Harley-Davidson Dealer. If two modules are already installed on top of the radio, two Dual-LockTM mounts, (76434-06), will be needed. Models WITHOUT a Tour-Pak installed will require the additional purchase of a Frame Mount CB Antenna Kit (76415- 06). Models WITH a Tour-Pak installed will require the additional purchase of a Tour-Pak Mount CB Antenna Kit (76414-06). All of these items are available from a Harley-Davidson Dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Electrical Overload It is possible to overload your motorcycle’s charging system by adding too many electrical accessories. If your combined electrical accessories operating at any one time consume more electrical current than your vehicle’s charging system can produce, the electrical consumption can discharge the battery and cause vehicle electrical system damage. See a Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories, or for necessary wiring changes. (00211b)

Incoming search terms:

Harley Davidson Installing The Ride Time Ultra Progressive Tour Pak LED Tail Lights

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Remove the light bulbs from the tail light housing by depressing the tab on the bulb socket assembly and turning counter clockwise. Remove the bulb from the bulb socket. 2. Remove the lenses from the warp-around light fixture. These lens are held in place by a non-hardening black sealant. In addition, there are three plastic alignment tabs on the lens body that clip into the lens frame. To remove the lens, insert the supplied push Stick through the hole in the back of the light bulb housing and gently but firmly push the lens outward. This action places a stress on the alignment tabs. 3 . Using a flat blade screw driver, pry the lens away from the frame at the top, side, and bottom to release the lens alignment tabs. Go back to step 2, and use the plastic tube to push the lens outward. It may be necessary to repeat the prying process and pushing process several times to remove the lens. Note: Some users have found it useful to heat the lens area with a hair dryer to soften the adhesive. Included in this kit are: Left and Right LED modules, 1 RTQC Quick Connect Accessory Cable , 2 RTV application sticks, 1 push stick, Approximately 3 inches of shrink tube, and 1 copy of instructions. Required for installation, but not included are: A tube of Permatex RTV (available at Wal-Mart), 1/8 inch drill bit, a drill, small flat blade screwdriver, other hand tools. Window/ body sealer if required to reseat lenses can be obtained at your local glass shop. Tour Pak, Harley Davidson, Electraglide, Raod King, and Ultraglide are registered trade marks of Harley David- son. Harley Davidson does not make or endorse the use of these lights. 4. When the lens begins to emerge from the frame, grasp it at the top and bottom and pull the lens from the housing using a up and down motion. Set the lens aside . Avoid having the sealant contact other surfaces. In most cases, the lens can be reinstalled without adding additional sealant . Note: Do not use RTV to reset the lens. If sealant is needed obtain a non-hardening body/windshield sealant from your local glass shop. 6. When you are comfortable with the location of the circuit board, drill a 1/8 inch hole in the back of the light housing. This hole will be used to bring the turn signal wire from the LED module into the Tour Pak. 7. Using the supplied stick, spread a thin layer of Permatex clear RTV silicone seal along the area where the circuit board will be located. Apply a similar layer to the top of the light housing. Route the turn signal wire through the 1/8″ hole and position the circuit board in the housing. Allow the RTV to cure. 5. Test fit the LED light board in the light housing.

Incoming search terms:

HARLEY DAVIDSON QUICK RELEASE DETACHABLE WINDSHIELD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
Installation The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308a) NOTE Cover the front fender, headlamp and the front of the fuel tank with clean shop towels to prevent scratching. Make sure the windshield assembly does not contact chrome or painted parts. Damage to the finish could result. Turn Signal Relocation Relocate the turn signals according to instructions included in the Turn Signal Relocation Kit, item 20. Assemble the Clamps to the Windshield 1. See Figure 1. Remove the windshield sub-assembly from the packaging and place face down on a clean, soft surface with the mount brackets facing upward. 2. See the Service Parts illustration. Remove both the clamp and hardware kits from the packaging, and separate similar parts in preparation for assembly. Note that upper and lower clamps are exactly alike. 3. See Figure 2. Assemble the clamp assemblies and hardware stacks. The cupped side of the Belleville (cone) washers must face each other and sandwich the windshield mount brackets at each mount point. Failure to orient washers correctly can reduce the windshield’s ability to break away in a collision, which could result in death or serious injury. 4. See Figure 2. One clamp at a time, with the clamp facing upward and inboard of the windshield bracket (2), tighten the shoulder bolts (1) enough to hold the clamp orientation to the windshield during mounting of the windshield to the bike. The bolts will be fully tightened later. Install the Windshield NOTE Keep front wheel straight to prevent brackets from scratching fuel tank. 1. Make sure all four clamps are in the “open” position, then bring the windshield (with the clamp side away from you) to the front of the bike. 1 WARNING 1 WARNING ® Kit Numbers 58779-05, 57160-05 1 of 3 Figure 1. Windshield Mounting Brackets i07503 Figure 2. Windshield MountingClamp i07504 1 Shoulder bolt 2 Right windshield bracket 3 Cup washer 4 Belleville washers (cupped sides face each other with windshield bracket between)

Incoming search terms:

2010 Harley-Davidson FLHR Road King front and rear 4-piston braking system Installation

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
in Vivid Black with blue and silver pinstripes, six-speed. Air-cooled, Twin Cam 96™ engine with Electronic Sequential Port Fuel Injection (ESPFI), ABS, security system, cast wheels with independent front and rear 4-piston braking system. Motorcycle generously donated by Harley-Davidson Motor Company Police & Fleet Sales. MSRP excludes all taxes title/documentary fees, registration, tags, dealer prep, labor and installation charges, insurance, optional equipment and accessories, certificate of compliance or non-compliance fees, and finance charges. Delivery must be coordinated through Rockville Harley-Davidson by November 30, 2010. Winner is responsible for any applicable fees above. 6,000 tickets printed. Odds of winning are 1:6,000. Ticket holder need not be present to win. Licensed by the D.C. Lottery and Charitable Games Control Board. Must be 18 years or older to win. No substitutes, return for cash, or other models. As per IRS tax code, amounts paid for chances in a raffle do not qualify as a deductible charitable contribution. Taxes on prizes are the responsibility of the winner. Harley-Davidson is proud to be a sponsor of the National Law Enforcement Officers Memorial Fund. Harley-Davidson Motor Company is a prize provider only, and Harley-Davidson, Inc., and Harley-Davidson Motor Company have no responsibility regarding conduct or administration of the raffle.

Incoming search terms:

Incoming search terms: