harley horn wiring diagram

You search Auto repair manual PDF harley horn wiring diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  harley horn wiring diagram Direct Download speed 5282 Kb/s

  harley horn wiring diagram Full Version speed 6162 Kb/s



HARLEY DAVIDSON HORN COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove seat and disconnect wires from horn. 2. See Figure 1. Remove stock horn bracket nut (2) and the entire stock horn cover assembly (1). Remove the horn (3) and all hardware components from the stock cover including wire clamp, clips, and mounting bracket. Leave rubber mount and locknut on motorcycle. Note assembly order for kit installation. NOTE Do not over-tighten “horn to horn cover” nut. Over-tightening may result in permanent damage to the horn. 3. Apply Loctite 271 (Red) to threads of nut (4) fastening the horn to the horn cover. Tighten nut to 80-100 in-lbs (9.0- 11.3 Nm). Tighten screws fastening the horn cover to the horn bracket to 35-55 in-lbs (4.0-6.2 Nm). 4. Route wiring harness through the clamp (if present) and install the entire horn cover assembly to the mounting stud (5). 5. Tighten nut (2) fastening the horn bracket to the horn rubber mount to 80-100 in-lbs (9.0-11.3 Nm). Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 6. Connect wires to terminals and reconnect battery. NOTE Horn is not polarity sensitive. Ground and power wire may be connected to either terminal. 2 4 1 5 3 is03958 1. Horn cover assembly 2. Bracket nut 3. Horn 4. Nut 5. Mounting stud Figure 1. Horn Cover Installation 7. Test horn. NOTE Test the horn only when mounted on the vehicle. The sound may be muffled if tested when hand-held. A muffled sounding horn that is mounted to a vehicle may indicate permanent damage to the horn by over-tightening the horn to horn cover nut (Figure 1, Item 4). Attempt to adjust nut torque. Replace horn if necessary. 8. Reinstall seat

Incoming search terms:

HARLEY DAVIDSON SMOOTH HORN COVER INSTALLATION INSTRUCTION

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
INSTALLATION 1. Refer to your model motorcycle’s Service Manual and remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect the battery cables, negative (-) cable first. 3. See Figure 1. Remove stock horn bracket nut (2) and the entire stock horn cover assembly. Remove the horn wires, horn and all hardware components from the stock cover including wire clamp, clips and mounting bracket. Note assembly order for reinstallation. 4. Position the horn (3) inside the new cover. Apply 1-2 drops of Loctite 271 (red) (Harley-Davidson Part Number 99671- 97) onto threads of nut (4). Install nut onto horn mounting stud (6) and tighten to 90-100 in-lbs (10-11 Nm). NOTE Do not over-tighten “horn to horn cover” nut . tighten to 90-100 in-lbs (10-11 Nm). Use in-lbs torque wrench. Over-tightening may result in permanent damage to the horn. 5. Route wiring harness through the clamp, (if present) and install the entire assembly to the horn assembly mounting stud (5). 6. Connect wires to terminals and reconnect battery. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) NOTE The horn is not polarity sensitive. The ground and power wires are interchangeable on the horn terminals

Incoming search terms:

KAWASAKI VOYAGER AIR HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 27-12-2010

download
1. Remove the false fuel tank cover to expose the battery. Remove the right hand lower leg fairing. (4 phillips screws). Unplug the stock horn and remove the (2) 10mm bolts securing it to the frame. 2. See photo #1 using the stock horn bolts attach the black horn mounting bracket and the white ground wire supplied as shown. Next locate the relay supplied. Plug the stock horn wires into the relay terminals #85 & #86. (see wiring diagram on back side of instructions) 3. Attach the air hose to the compressor air outlet fitting. Attach the short red wire supplied to the compressors positive (+) terminal and the white wire installed earlier to the compressors ground (-) terminal. As shown in photo #2. Attach the compressor to the frame with the hose clamp provided. Note: position the top of the compressor as shown touching the bottom of the horn mounting bracket and approximately 1 Ω” to the rear of radiator and shroud. Also the air hose and fitting should be in front of the frame tube with the hose routed inside the hose clamp without pinching the hose. Attach the red wire from the compressor to one of the relays remaining outer terminals #30 or #87. Attach the remaining long red wire (supplied) to the remaining relay terminal #30 or #87. Secure the relay to the frame with a cable tie supplied. Route the red wire up to the battery positive (+) terminal. Locate the fuse wire assembly provided. Attach the fork end of the fuse wire to the battery positive (+) terminal. Cut the red wire to the desired length, strip the end and crimp to the fuse assembly. Turn on the ignition and press the horn button, you should hear the compressor motor run. Re-install the false fuel tank lid. Re-install the right lower leg fairing while routing the air hose out next to the black horn mounting bracket 4. See photo #3, Bolt the horn set to the black mounting bracket using the 5/16 x æ”bolt, washer and lock washer provided. Trim the air hose to length if necessary and attach the air hose to the horn assembly. Install the trumpet covers. (see instructions enclosed with covers) Turn on the ignition and test the horns

TRIUMPH ROCKET III ELECTRIC HORN HARDWARE KIT INSTALLATION

0

Filed Under (Triumph) by admin on 24-12-2010

download
1. Remove the seat and left hand side cover. (held in place by two (2) 10mm bolts) Remove the chrome cover from the stock horn located below the headlights. (held in place by two (2) 5mm allen screws at the top of the cover) 2. Unplug the wires from the stock horn. Locate the supplied jacketed cord and attach the end with the piggyback jumpers to the horn wires. Plug these back onto the horn terminals as shown in photo (1). Remove the black plastic left side steering head frame cover (held in place with two (2) 5mm allen screws). Route the cord behind the headlights, along the left side of the frame and over the engine keeping it neatly out of sight. Route the end if the cord to where the relay will mount as shown in photo (2A). Replace chrome horn cover and steering head frame cover. 3. Using the relay supplied, refer to the wiring diagram included with the horn set and the small numbers next to the terminals on the relay. Connect the 2 wires from the jacketed cord to terminals #85 & #86. Connect the blade terminal of the fuse wire assembly (supplied) to terminal #30 on the relay. Attach the other end of the fuse holder to the positive (+) battery terminal. 4. On the horns bend the wire terminals outward so that they will be parallel to the mounting brackets when installed. Refer to photo (3) and assemble the horns onto their supplied mounting brackets as shown. Bolt two (2) of the four (4) flat silver brackets on each of the horns using the 6mm nuts and lock washers supplied. Bolt the black bracket to the left hand horn using the 6x12mm bolt and nyloc nut supplied. Place the 6 x 35mm bolt with a washer and lock washer thru the right hand horn bracket then the left hand black bracket and place the 3/8″ flange nut over the back of the bolt. Remove the bolt where the horns will mount (see photo 2B) and bolt the horn set on as assembled with the flange nut on the back side of the black bracket. Align the horns as shown in photo (2) being careful that the horns do not make contact with each other or any other parts as this will significantly reduce their output then tighten the bolt securely.

EDELBROCK NITROUS SYSTEM UNIVERSAL MOTORCYCLE NITROUS SYSTEM

0

Filed Under (Suzuki) by admin on 26-11-2010

download
Wiring Diagram #1 Wiring Diagram #2 Red Red Red Red Black Black Black Black Black Black Factory Harness to Horn Factory Harness to Horn Horn Horn Nitrous Solenoid Nitrous Solenoid Switch Switch Bottom View Bottom View +12V with Key On From Horn Button (Ground when button is pressed) From Horn Button (Ground when button is pressed) To Nitrous Bottle To Nitrous Bottle To Nitrous Nozzle To Nitrous Nozzle Install Relay for OPTIONAL RPM Activated Switch Here. See Section 7.0 for More Details. Install Relay for OPTIONAL RPM Activated Switch Here. See Section 7.0 for More Details ©2007 Edelbrock Corporation Brochure #63-71940 Catalog #71940 Rev. 2/07 – DC/mc Page 4of 4 To Nitrous Bottle To Nitrous Nozzle Nitrous Solenoid To Starter Solenoid Switch Bottom View Ground Starter Button +12V when Pushed Install Relay for OPTIONAL RPM Activated Switch Here. See Section 7.0 for More Details. Wiring Diagram #3 Starter Button Activation for Suzuki Hayabusa 7.0 – WIRING MSD 8950 RPM SWITCH NOTE – This is a suggested wiring application. There are many ways that the RPMswitch may be installed. The installer needs to set RPMswitch to proper RPM and test operation. Use diagrams on page 3 for relay terminal #30 connection. Nitrous Solenoid To Nitrous Bottle To Nitrous Nozzle RPM ACTIVATED SWITCH 10,000 Desired RPM Chip Here Connect as Outlined in Wiring Diagrams White to 4-Coil Tach Adapter #T-101-MSD Black Battery Ground Yellow – N/C Gray – OFF When Set RPMis Exceeded Connect as Outlined in Wiring Diagrams NOTE – RPM Chips are Ordered Separately Red to Switched +12 Volt Tailight Power or any Other +12 Volt Source with the Key On Note – This Method Will Turn the Nitrous Off When Set RPM has Been Exceeded. 85 87A 30 86 87 A Test Light Can Be Used Here to Check Operation 8.0 – OPTIONAL PRODUCTS FOR EFI MOTORCYCLES A Progressive Timing Retard Controller is available from Schnitz Racing for fuel injected motorcycles. The EFIR Series Timing Retard Controllers can be used with or without a Power Commander installed.

Incoming search terms:

HARLEY DAVIDSON CHROME FAN KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
INSTALLATION 1. Refer to Service Manual and remove seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery negative cable. Horn Relocation NOTE This cooling fan is designed to provide supplemental cooling for motorcycles subjected to long periods of idling/parade duty. The fan is mounted on the left side of the engine in the area where the horn is mounted. The stock horn must be removed. Remove Stock Horn 1. Follow Service Manual instructions to remove stock horn and its bracket. 2. Assemble new horn 69043-96B to bracket 69135-04 using screws 3658 and washers 7069. 3. Remove right front fuel tank TORX® screw. 4. Mount horn at front of fuel tank with TORX screw. Verify there is adequate room between horn bracket and fuel tank to prevent paint damage. Tighten screw to 15-20 ft- lbs (20-27 Nm) . 1 is05140a 1. Horn mounting location Figure 1. Horn Relocation Remove Stock Upper Engine Mounting Bracket 1. Remove screw securing rear of fuel tank and gently raise fuel tank to gain access to upper engine mounting bracket. Place suitable blocking under tank. 2. On 2007 models remove bolt attaching stabilizer link to upper engine mounting bracket. 3. Remove two bolts and washers securing upper engine mounting bracket to front and rear cylinder heads. Retain bolts and washers for attaching new upper engine mounting bracket from kit. 4. Note position of fuel hose. Remove upper engine mounting bracket. 5. Connect horn relocation harness to horn. 6. Route stock horn wires forward towards relocated horn. 7. See Figure 7. Cut ends off stock horn wires and strip wires 3/8 inch. Follow instructions in Service Manual, “SEALED

VICTORY HAMMER, KINGPIN, VEGAS AND JACKPOT ELECTRIC HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Victory) by admin on 29-01-2011

download
1. Remove the left and right plastic side covers and the seat (two allen bolts located below the sides of the seat). Unplug and remove the stock horn (located over the oil cooler). Connect the female ends of the jacketed two wire cable supplied to the original horn wires. Route the other end of the cable up over the engine and back to where the relay will mount as shown in photo (1). 2. Using the relay supplied with this kit and the wiring diagram provided with the horn set, identify the terminals of the relay (there are very small numbers next to each of the terminal). Connect the two (2) wires from the cable to terminals #85 & 86 on the relay. Locate the fuse holder wire assembly supplied and connect the blade terminal to the relay terminal #87 or #30. Connect the other end of the fuse wire to the battery positive terminal (+). 3. Working under the left side of the motorcycle, refer to photo (2) and install the black bracket supplied as shown onto the engine mount. Locate the four thin flat brackets and two (2) 6mm nuts supplied with the horn set and two lock washers supplied with the kit. Bolt two (2) of the brackets to each of the horns using a lock washer and 6mm nut on each and make them snug. Using the remaining 6 x 12mm bolt, nut and lock washer install the horns onto the black bracket and align as shown in photo (3). Adjust the horn location so that they are free to vibrate and do not come in contact with other parts of the motorcycle then tighten all three 6mmm bolts securely. 4. Using the two remaining wire assembles supplied, connect the larger terminals with double wires to one of the horns and the terminals with the single wire to the other horn. Route these wires up thru the frame to the relay. Connect the wire with the female blade connector to the relay terminal #30 or #87. Connect the ring terminal to the battery negative (-) terminal
or any 6m bolt on the frame. Turn on the ignition and test the horns. Secure the relay to the frame or other wiring and all loose wires using the cable ties supplied. Replace the seat and side covers

Incoming search terms:

HARLEY DAVIDSON WIRE LOOM AND HORNS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
Remove the stock horn and bracket from the stud it is mounted to and unplug the 2 wires. Remove the seat. Route the end of the wire and hose loom without the connectors. Starting in front of the fuel valve, route this loom behind the valve, over the fuel line over the rear cylinder head along the existing wiring or hoses – if your model has any. Follow the frame to where the back bone and seat support rails come together. Route the loom up into the general area where the compressor will mount (i.e. see diagram). Attach the hose to the ‘Y’ connector on the horns themselves. Attach the two black wires from the loom to the relay terminals #87 and #30, located between the air horns behind chrome cover. Attach the wires from the original horn to the remaining terminals #85 and #86 (NOTE: it makes no difference which wire goes to which terminal). Attach the relay to the back of the horn bracket assembly or up under the fuel tank using the small cable tie provided. NOTE: the terminals must point downward to prevent water from entering the relay! Install the horn assembly using the 1/4″ thick chrome washer provided behind the horn mounting bracket. Use the original acorn nut and tighten securely. Check to see that the horns have at least 1/4″ clearance between the engine, shift linkage and choke knob. They should be horizontal or angle down at the front just slightly. Take any slack out of the loom, keeping it up against the frame and away from the engine or exhaust, using several of the small cable ties provided. COMPRESSOR MOUNTING AND WIRING Due to the vast differences in years and models, it is not possible to have one or two brackets that will fit all models. You may need to mount the compressor in a different position or find an alternative location, such as under one of the side covers. On 2001 and newer Tour models there is room in front of the battery to mount it horizontally. On 1997-2000 fuel injected models, under the front portion of the right hand side cover is an excellent location. On most Softtail models you can attach it to the frame tube behind the rear cylinder. On some models such as Sportsters there may not be a place to conceal the compressor; there is a chrome cover and cap available to dress it up for exposed mounting. (RIVCO part no #CMPCR) If mounting the compressor vertically as pictured, try to keep the end with the electrical terminals pointing downward. You can use the long cable ties provided to attach the compressor to the frame or an existing wiring loom. Once the compressor has been mounted securely, route the hose and one of the wires to it and connect the hose to the air outlet barb or fitting. Trim the wire and crimp on one of the female blade terminals and attach to the (+) terminal. Attach the white ground wire supplied to frame close enough to the compressor, so the wire will reach. Trim and crimp another female terminal to it. Attach this wire to the (-) ground terminal. The remaining black wire from the hose/wire loom goes to the battery (+) terminal through the fuse and holder provided. Trim the black wire allowing for the length and placement of the fuse holder. Crimp together and attach to the battery (+) terminal. Turn ignition on and test horns. Check wires and hoses for neat, secure routing and at least 1″ away from exhaust system. Reinstall seat etc.

Incoming search terms:

SUZUKI SV 1000 RADIATOR (COOLING SYSTEM) SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FI SYSTEM MALFUNCTION CODE AND DEFECTIVE CONDITION MALFUNCTION CODE DETECTED ITEM DETECTED FAILURE CONDITION CHECK FOR COO NO FAULT C11 Camshaft position sen- sor The signal does not reach ECM for more than 3 sec . after receiving the starter signal . The camshaft position sensor wiring and mechanical parts (Camshaft position sensor, intake cam pin, wiring/coupler con- nection) C12 Crankshaft position sensor The signal does not reach ECM for more than 2 sec . after receiving the starter signal . The crankshaft position sensor wiring and mechanical parts (Crankshaft position sensor, wiring/coupler connection) C13 Intake air pressure sensor The sensor should produce following voltage . (0.50 V < sensor voltage < 4 .85 V) Without the above range, C13 is indicated. Intake air pressure sensor, wiring/coupler connection C14 Throttle position sen- sor The sensor should produce following voltage . (0.20 V < sensor voltage < 4 .80 V) Without the above range, C14 is indicated. Throttle position sensor, wiring/coupler connection C15 Engine coolant temperature sensor The sensor voltage should be the following. (0.15 V <_ sensor voltage < 4 .5 V) Without the above range, C15 is indicated. Engine coolant temperature sensor, wiring/coupler connection C21 Intake air temperature sensor The sensor voltage should be the following. (0.15 V < sensor voltage < 4 .5 V) Without the above range, C21 is indicated. Intake air temperature sensor, wiring/coupler connection C22 Atmospheric pressure sensor The sensor voltage should be the following. (0.50 V < sensor voltage < 4 .5 V) Without the above range, C22 is indicated. Atm. pressure sensor, wiring/coupler connection C23 Tip over sensor The sensor voltage should be the following for more than 2 sec . after ignition switch turns ON . (0 .20 V < sensor voltage < 4 .80 V) Without the above value, C23 is indicated. Tip over sensor, wiring/coupler connection C24 or C25 Ignition signalCrankshaft position sensor signal is produced and ECM determines the ignition signal but signal from ignition coil is interrupted continuous by 4 times or more. In this case, the code C24 or C25 is indicated. Ignition coil, wiring/coupler connection, power supply from the battery SERVICING INFORMATION 8 .3 C28 Secondary throttle valve actuator No operating voltage is supplied from the ECM, C28 is indicated. STVA can not operate. STVA lead wire/coupler, STVA C29 Secondary throttle valve position sensor The sensor should produce following voltage . (0.10 V < sensor voltage < 4 .90 V) Without the above range, C29 is indicated . Secondary throttle position sensor, wiring/coupler connection C31 Gear position signalGear position signal voltage should be higher than the following for more than 2 seconds. (Gear position switch voltage >_ 0 .6 V) Without the above value, C31 is indicated. Gear position sensor, wiring/coupler connection, gearshift cam, etc. C32 or C33 Fuel injector Crankshaft position sensor signal is produced and ECM determines the injection signal but fuel injection signal is interrupted continuous by 4 times or more. In this case, the code C32 or C33 is indicated. Injector, wiring/coupler connection, power supply to the injector C41 Fuel pump relay No voltage is applied to fuel pump although fuel pump relay is turned ON, or voltage is applied to fuel pump although fuel pump relay is turned OFF . Fuel pump relay, connecting lead, power source to fuel pump relay C42 Ignition switchIgnition switch signal is not input in the ECM . Ignition switch, lead wire/coupler C44 Heated oxygen sensor (HO2S) [For E-02, 19] During 02 feedback control, 02 sensor voltage is higher or lower than the specification . No signal is detected during engine operation or no electrical power is supplied from the battery . HO2S lead wire/coupler connection Battery voltage supply to the HO2S C49 PAIR control solenoid valve (PAIR valve) When no operating voltage is supplied from the ECM, C49 is indicated. PAIR valve can not operate. PAIR valve lead wire/coupler

Incoming search terms:

HONDA VTX1300 AIR HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Remove the rider and passenger seats, left chrome side cover & original horn located at the top of the radiator. 2. Locate the supplied black horn mounting bracket and supplied smaller hose clamp. Notice the slight twist in the bracket. Using 2 adjustable wrenches or a vise and one wrench remove the twist from the bracket. Route the hose clamp thru the bracket. (As shown in photo 1A) 3. Install the bracket on to the left frame tube, (As shown in photo 1A) and tighten securely. Bolt the supplied horns to the bracket using the supplied bolt, lock washer and nut, (As shown in photo 1) and tighten securely. Install the supplied trumpet covers (As shown in photo 1B) by flexing the spring clips over the trumpets. Check that they fit securely. If not remove covers, make sure the center screw is tight and bend spring clips in towards center of covers and re-install. Using a blade screwdriver pry the two supplied hoses with the “Y” connector off of the air horns cut a new piece of hose 3 ½” long from the hose and replace the short hose on the “Y”. Re-install the “Y” hose assembly with the short hose going on the long or upper trumpet. (See photo 1C) Re-route the original horn wires. (As shown in photo 1D) 4. From the supplied wire cut 2 pieces 28″ long. Strip ¼” of insulation from both ends. Crimp 2 supplied male terminals to one end and 2 supplied female spade terminals to the other end. Plug the male ends into the original horns wires. (As shown in 1D) Attach the remaining air hose to the “Y”. Tape the hose and wires together every 6-8″ using electrical tape to make routing easier and neater. Route the wires and hose up under the fuel tank, over the cylinder heads coming out between the frame rails at the rear of the fuel tank. (See photo 2A) Locate the supplied relay and plug the 2 wires from the original horn onto terminals 85 & 86 on the relay. (See wiring diagram on back of last page of instructions) This will be the 2 outer terminals that are parallel to each other. Locate the supplied fuse, holder & wire assembly. Crimp a supplied fork terminal to one end and a supplied female spade to the other. Attach the spade terminal to one of the remaining outer relay terminals. (#30 or 87 on wiring diagram) Remove the 3 Phillips screws from the battery top cover. Remove the cover and attach the fork end of the fuse wire to the positive (+) terminal. Re-install the battery cover. 5. Cut a wire 9″ long and strip ¼” insulation from each end, crimp a fork to one end and a female spade to the other. Attach this wire to the compressors negative (-) terminal. Cut another wire 18″ long and strip both ends. Crimp a female spade to both ends. Attach this wire to the compressor positive (+) terminal. Route the air hose out under the left side cover as shown in photo (3). Hold the compressor in place against the frame tube. Note: Looking at the large end of the compressor the space between the hose fitting and the bolt mounting flange forms a “V” shape. This is where the compressor should rest against the frame. Next loop the hose around to the compressor hose fitting and trim the hose to the desired length. Attach the hose to the compressor. Secure the compressor to the frame using 2 large supplied cable ties as shown. 6. (See photo 3A) Attach the compressor negative (-) wire to the bolt on the frame (As shown in photo 3B) Route the compressor positive (+) wire along the side up to the relay and attach to the remaining outer terminal 87 or 30. Cable tie the relay in place. (As shown in photo 2B) Use several of the supplied short cable ties to secure the compressor wires to the air hose (As shown in photo 3) as wells as any other loose wire or hose.

Incoming search terms:

Incoming search terms: