harley points wire gauge

You search Auto repair manual PDF harley points wire gauge, if there are search results will appear below. If search results do not exist, please search by others keyword.



  harley points wire gauge Direct Download speed 5282 Kb/s

  harley points wire gauge Full Version speed 6162 Kb/s



HARLEY DAVIDSON LED FUEL GAUGE KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Removing the Analog Fuel Gauge NOTE The fuel gauge wires are routed through a tube in the fuel tank, and are secured by a clip at the bottom of the tank and, on some models, a clamp on the frame. Open the clip and clamp as needed, and be sure there is enough slack in the wires to be able to lift out the gauge. 1. At the bottom left side of the fuel tank, bend back the flexible clip slightly to free the fuel gauge conduit. Open the harness clamp on the frame if necessary to free the conduit. Gently pull on the conduit to draw the Multilock connector [117] out of the tunnel. 2. See Figure 2. Depress the pin on the socket terminal side of the connector, and pull apart the pin and socket halves. 3. See Appendix B in an appropriate Service Manual. Use a pick (Snap-On TT600-3 or equivalent) to remove the terminals or clip off the wires. Remove and discard the fuel gauge. 4. For Carbureted Models: See Figure 2. Remove the fuel gauge by firmly grasping and carefully pulling up (do NOT twist) on the gauge just far enough to free it from the fuel tank. Disconnect the two sending unit connectors. Feed the conduit and two wires up through the tube while removing the gauge. Remove and discard the fuel gauge. For Fuel-Injected Models: See Figure 2. Remove the fuel gauge by firmly grasping and carefully pulling up (do NOT twist) on the gauge to free it from the fuel tank. Feed the conduit and three wires up through the tube while removing the gauge. Remove and discard the fuel gauge. 5. Remove and discard the rubber gasket. INSTALLATION For Kit Numbers 75084-04B or 75237-03B 1. See Figure 2. Assemble the new gasket (3) to the LED fuel gauge (1) from the kit. Install the gasket so the flat side contacts the edge of the gauge. 2. See Figure 1. Use three of the Phillips-head screws and washers from the kit to connect the wires as follows: Fasten the Orange wire (1) ring terminal to the gauge connection marked “12V and “O” with a screw and washer. Fasten the Black wire (2) ring terminal to the connection marked “GND” and “BK” with a screw and washer. Fasten the Yellow/White wire (3) ring terminal to the connection marked “Y/W” with a screw and washer. 3. See Figure 2. While carefully lowering the fuel gauge, feed the wire harness (2) down into the drain tube until the three short (Orange, Black, Yellow/White) wires exit the hole at the bottom of the fuel tank. Gently pull the wires to remove slack while installing the gauge to the fuel tank. Do not twist the gauge during installation. Hold the gauge firmly and press down until it snaps into place

Incoming search terms:

1982-2005 Harley Motorcycle Removal and Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-03-2012

download
” bolt from the mounting stem on the Signal® mirror. While seated on the motorcycle, position the Signal® mirror on the handle bar. Secure the Signal® mirror to the handle bar using the 5/ 16 ” bolt. Make sure the bolt is tight! Guide the Signal® mirror wire harness into the cowling by going along side the existing factory wire harness. 4 Remove any slack in the wire harness. Secure the wire harness to the handle bar using a supplied tie wrap. 5 6 Adjust the position of the Signal® mirror and tighten the ball retention screws. Remove the motorcycle seat. Remove the aft mounting bolts on the fuel tank. 7 Guide the Signal® mirror wire harness along the inside of the fuel tank’s front mounting bolt and between the crossover tube. 8 9 Lift up the aft portion of the fuel tank and guide the Signal® mirror wire harness down the backbone of the motorcycle frame, alongside the existing factory wire harness. The motorcycle’s electrical wiring for turn indicators is located aft of the gas tank on the backbone of the frame. Guide the new wire harness from the Signal® mirror to the electrical wiring. Cut off any excess slack in the wire. Locate the SOLID BROWN wire from the wire connector. Turn the ignition key so that electrical power is on and activate the right side turn indicator. Probe the wire with the wire tester to verify that flashing turn indicator power is present. Label that wire as ‘right side turn’. Repeat all of the previous steps to replace the left side factory mirror with the new Signal® mirror. Locate the SOLID VIOLET wire from the wire connector. Activate the left side turn indicator and probe the wire with the wire tester to verify that flashing turn indicator power is present. Label that wire as ‘left side turn

Incoming search terms:

Harley-Davidson Road King Handlebar Removal and Installation Manual

0

Filed Under (Harley Davidson) by admin on 18-03-2012

download
If the wire length appears to be too short, you will have to lengthen the wires. If that’s the case, I must stress that soldering your wires is far superior to using butt splices. Wiring can be pulled from the splices and the splices themselves will take up a lot of room, making your harness bulky. To extend your wires, ensure the wire segments you are going to splice into the harness are of the same gauge as the original harness. Also, it’s a good idea to cut all of the wire segments now, ahead of time, to the same measured length. This will ensure that once all of the new wire Figure 4. Handlebar harness plug wires as they appear from the back of the plug (where the wires enter the plug from the harness) segments are spliced in, all of the finished wires are of the same length and the pins are lined up. Work from wire to wire, cutting them by staggering the cuts about an inch or so apart (see figure 5). This will prevent a bulge in your harness where all the soldering connections are. After cutting each wire, slide on a two-inch piece of heat shrink tubing before starting your soldering. Remove about ¾” of insulation from the ends of the two wire ends (one wire end being the harness, the other being the segment of new wire being spliced in). Halfway down the length of its exposed section, bend each wire 90 degrees and hook the two wire segments together at the bends. Holding the wires securely with a pair of pliers, twist them in opposite directions around each other. Make sure the ends of the wires are wrapped as tight as possible so their sharp points will not cut through the heat shrink tubing when it’s applied. Apply some soldering flux (a little is all you need) and solder the connection by first applying your soldering iron (or gun) to the wire and then applying the solder to the wire. You should not apply the solder directly to the iron as overheating the solder can lead to poorly made solder joints and improper conduction of electricity. When the connection has cooled, slide your heat shrink tubing over the joint and heat it so that the tubing shrinks, making a nice tight seal.

HARLEY DAVIDSON DETACHABLE QUARTER FAIRING AND DOCKING HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
Installation The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley- Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE If your motorcycle has directional lights mounted on the upper fork bracket they must be relocated to the bottom fork bracket. Some models have front directional lights equipped with three wires, the third black wire is a ground wire. Check to determine how many wires are connected to the front directional lights and follow the following procedure that applies. Ifdirectional lights are not mounted on the upper fork bracket proceed to “ASSEMBLING FAIRING”. Relocating Two Wire Directional Lights 1. Support motorcycle on a center stand such that front wheel is raised slightly off the ground. 2. Remove fork tube pinch screw from right side of lower bracket. 3. Cut wires connected to right directional light about 2 in. away from directional light body. 4. Remove fork tube pinch screw from right side of upper fork bracket. (This is the screw that secures the right directional light.) 5. Install right directional light on right side of lower fork bracket using pinch screw removed in step 4. Install pinch screw removed in step 2 into right side of upper bracket. Tighten both pinch screws to 30-35 ft-lbs. 6. Repeat steps 1 through 5 to relocate left directional light. NOTE Fork tubes may slide downward within fork brackets. If this occurs, front fork tube extension above front fork upper bracket will have to be readjusted according to appropriate Service Manual procedures. 7. Connect the right directional light as follows: Strip approx. 5/16 in. of insulation from the wires cut in step 3. 8. Crimp solderless connectors from kit on two wires coming from motorcycle. 9. Split one end of the 2-conductor polarized wire from kit back about 2 in. and strip 5/16 in. of insulation from wire ends. 10. Slide a piece of shrink tubing from kit over each of the wire ends stripped in step 9 and crimp the wires into the terminals installed in step 8. Make sure you connect the silver and copper colored wires to like colored wires. NOTE Polarized wire is used in this application to ensure correct wiring. One wire is silver, one is copper colored. Wire colors of spliced wire must match wire color of original directional wire leads. 11. Cut polarized wires to the length required for connection to the wires at the relocated directional light. Make certain you leave enough slack in wires to allow routing the harness along the fork tube. 12. Split remaining end of the 2-conductor polarized wire from kit back about 2 in. and strip 5/16 in. of insulation from wire ends. 13. Slide heat shrink tubes over the two wire end. 14. Strip 5/16 in. of insulation from wires connected to directional light and connect like colored wires at directional light with connectors from kit. 15. Slide heat shrink tubing over connectors installed in steps 10 and 14. Activate shrink tubing with heat gun or hair dryer.

Harley-Davidson Electronic Ignition Module Installation instructions

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
Step 1: Switch main dashboard switch to “off” position (Ignition& light switch) Step 2: Disconnect negative (ground) cable from the Battery Step 3: Remove the Condenser and Breaker points from the circuit breaker timing base. Step 4: Disconnect advance/ retard cable from timing base Step 5: Remove timing base from timer shaft and housing (see your manual for instructions) Step 6: Remove circuit breaker wire stud or circuit breaker to coil wire assembly from timing base Step 7: Remove circuit breaker wire from Ignition coil, and mark terminal on coil with piece of tape. Step 8: Install the Electronic Ignition Module on the timing base. Mount this short black wire to one on the timer base screws by keeping some slack in this wire so the timing base can turn free. Solder the flag terminal to this short black wire and mount it under the timer to motor bolt. This way of mounting provides a much better grounding. Do NOT use the screws (number 1 or 2 screws from picture below) from the timing base!!!! Step 9: Now three wires pass this hole via the rubber grommet. Figure 1 Figure 2 Step 10: Reinstall the timer base on the timer shaft housing, and keep some slack in the wires before protruding the hole in the timer shaft housing, and secure with ground spring and cover retainer. Reconnect the advance/retard cable to the timer base. Step 11: Route the two long wires to the ignition coil. Check in the HD service manual for a proper route to the ignition coil. (Keep away from hot surfaces like exhaust systems). Cut the wires to the exact length necessary for mounting. Step 12: Determine the exact length of the wire loom. Keep in mind that one end of the loom enters the timer shaft housing by 1cm. Cut the loom to the proper length. Step 13: Insert both wires in the loom. Strip both wire ends and solder the two flag terminals on the wires. Step 14: Connect the red wire to the ignition coil, on the terminal where the 6 or 12 volt is supplied to. This terminal has at minimum one wire connected which runs to the main switch. Step 15: Connect the black wire to the ignition coil on the terminal which is empty, and has piece of tape on it. (Old place where the circuit breaker wire was connected to) Step 16: Install the trigger rotor on the timer shaft cam, and tighten the hex screw by using the hex key tool. Do not over tighten the screw! Step 17: Check for clearance between trigger rotor and Electronic Ignition Module. Appropriate clearance is between 0,5mm and 1,5mm . Minor adjustments can be made by unlocking the two screws and slightly shift/move the Electronic Ignition Module. Check if the rotor moves free. Timing instructions: Remove the spark plugs from the engine, but keep them connected to the spark coil cables and engine ground. This enables normal operation of the spark, and prevents unwanted engine firing on compression stroke. See service manual or handbook for timing instructions of your model Step 18: Reconnect the negative (ground) cable to the battery. Step 19: Switch main power to “on” position. The red light in the Electronic Ignition Module might already light up. If not, turn the kick starter slowly. The red light is on while charging (closed points)the Ignition coil, facing solid metal of the trigger rotor. The light goes off (open points) when the end of the solid surface of the trigger rotor passes the centre of the Electronic Ignition Module. At that point a spark is generated by the coil

Incoming search terms:

SR-C400 Motorcycle Security System INSTALLATION MANUAL AND USER'S GUIDE

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Routing the Antenna Wire The MCM includes an 18″ antenna wire. The first 12″ is a coaxial wire; the remaining 6″ is the reception antenna wire. When routing, try to avoid running the antenna along or near metal. For best performance, have the antenna wire as vertical as possible and exposed. Wire Connections The system includes one harness (HAR-1a) that connects directly into the MCM. The harness is split into three plugs: one for the GEN-1a connector, one for the optional SN-5 connector and one for the data output for future expansion. Note: Each plug is unique and will only fit the appropriate component one way. Main Harness Note: If the optional factory connector kit is being used, please disregard this section of the instructions and refer to the instructions supplied with the factory connector kit. The main harness consists of two harnesses. One is labeled (HAR-1a) and the second is labeled (GEN-1a). Plug in the white 4 pin connector from the (HAR-1a) into the matching 4 pin connector from the (GEN-1a). The (HAR-1a) also has a waterproof connector that plugs into the MCM. The wires should be connected as follows: HAR-1a Black wire with fuse and ring terminal – To battery Positive (+). GEN-1a Black wire – To ground (-). Orange wire – To tail light wire or any other wire that is hot (+) when ignition is ON (NOTE: this is an input to the alarm this connection is not designed to flash the tail light). Color Codes: Ground (-) Tail Light Honda Green wire Brown wire Kawasaki Black wire Red wire Suzuki Black/White Brown wire Yamaha Black wire Blue wire Harley Davidson Black wire Blue wire

Incoming search terms:

HARLEY DAVIDSON FLHT OIL PRESSURE AND AIR TEMPERATURE GAUGE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION Oil Pressure Sending Unit To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. 1 2 3 4 is04574 1. Oil pressure sending unit 2. Cam position sensor 3. Crank position sensor 4. Main harness to ECM Figure 1. Electrical Bracket: 2000-2001 Fuel Injected Models (Magnetti-Marelli) 1 2 3 is04575 1. Oil pressure sending unit 2. Crankshaft position sensor 3. P&A siren kit Figure 2. Electrical Bracket (ECM Removed) 2002-2003 Fuel Injected Models (Delphi) -J01875 1 of 4 NOTE For 2002 to 2003 models: See Figure 2. Remove the two screws securing the ECM and remove the ECM to access the electrical bracket. 2. For 2004 and later models: Proceed to the Gauges section. For 2000 to 2003 models: See Figure 1, Figure 2 and Figure 3 for the applicable model and locate the sensor harness connector (2-piece mini-Deutsch® connector). 3 2 4 1 is04576 1. Ignition harness 2. Cam position sensor 3. Oil pressure sending unit 4. Crankshaft position sensor Figure 3. Ignition Module – Carbureted Models 3. Locate the oil pressure sending unit at the front right side of the crankcase and pull wire socket from terminal of the oil pressure sending unit. 4. Carefully draw the conduit and the pin side of mini-Deutsch connector forward and then up between the rear brake master cylinder reservoir and the frame downtube to area of the rear brake pedal. 5. See Figure 4. Remove the secondary locking wedge (3) from the pin side of the connector with a needle nose pliers. 1 3 2 is04577 1. Pin 2. Wire seal 3. Locking wedge Figure 4. Deutsch Connector Pin Side (2-pin connector shown) 6. Gently depress terminal latches inside pin housing and back out the pin in chamber #1 through the hole in wire seal. 7. Pull the oil sending unit wire through conduit and remove wire. Note the routing of the wire. 8. See Figure 9. Route the jumper (6) pins through the conduit from the kit in the same direction as the original wire noted in Step 7. Use cable straps to secure to the wire bundle. 9. See Figure 5. Locate pin chambers #1 and #2 on pin side of connector. Insert brown/green jumper pin into chamber #2 and feed until it clicks into place. Verify that pin will not back out of the chamber by giving a slight tug on the wire to confirm that it is locked

Incoming search terms:

TRIUMPH TWIN CYLINDER MOTORCYCLES WITH POINTS IN THE SIDE CASING INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 30-10-2010

download
1. All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation. 2. Remove the petrol tank and/or seat to gain access to the ignition coils, condensors and wiring. 3. For safety, disconnect the battery (preferably both terminals). 4. Remove timing cover. (The Atlas engine has the points housing behind the cylinder head). 5. Disconnect the two wires (usually black-white & black-yellow) and remove the contact-breaker plate. At the other end, these two wires must be disconnected from the ignition coils & condensors. The condensors are no longer required and can be removed. They should not be connected to the electronic ignition system. 6. Remove auto-advance unit. 7. Disconnect the remaining wires from the ignition coils. These come from the ignition switch supply. On the Norton Commando, remove the white-blue wire from the ballast resistor between the two ignition coils; the ballast resistor is no longer required. The colour of this ignition supply wire may be different on some machines; if so check using a test lamp or meter to find the live wire when the ignition is switched on. 8. Find a suitable place for the ignition module, preferably near to the ignition coils. Secure the ignition module to the frame using one or more large cable ties. An adhesive mounting base is provided; this can be affixed to the underside of the module and the cable tie passed through and around the module and frame. Do not completely wrap the module in foam rubber. 9. Using the black coil link wire, connect the negative (—) terminal of one ignition coil to the positive (+) terminal of the other ignition coil. See figs. 1/2 on page 7. 10. Take the black wire from the ignition module, cut to length and fit an insulator and female spade connector to the end. Connect to the negative (—) terminal on ignition coil #2. See figs. 1/2 on page 7. 11. Take the red wire from the ignition module, cut to length and fit an insulator and female spade connector to the end. Connect to the positive (+) terminal on ignition • BLACK COIL LINK WIRE • RED EARTHING WIRE • CRIMP CONNECTORS & INSULATORS • LARGE & SMALL CABLE TIES • CABLE TIE ADHESIVE MOUNTING BASE 3 coil #1. See figs. 1/2 on page 7. 12. For NEGATIVE EARTH electrics go to step 15. 13. For POSITIVE EARTH electrics (standard): Take the white wire from the ignition module, cut to length and fit an insulator and male spade connector to the end. Connect to one of the negative ignition feed wires previously removed in step 7 (white-blue wire for Norton Commando). The other wire (if fitted) is spare and should be covered with insulation to prevent shorting to the frame etc. 14. Take the red earthing wire, fit an insulator and female spade connector on one end and connect to the positive (+) terminal on ignition coil #1. Cut to length and fit a ring terminal on the other end and connect to a good earth point on the frame, ideally the battery positive (+) terminal. For the Norton Commando, the earth tag on the end of the condensor pack can be used (fit a female spade connector to the end of the red earthing wire). See fig.1 GOTO STEP 17

Incoming search terms:

DRAG SPECIALTIES MINI SPEEDOMETER WITH LED INDICATOR LIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Place the motorcycle on a level and secure area. Disconnect the battery. 2. Refer to the appropriate factory service manual and remove the OEM speedometer and indicator lights. The indicator lights usually unplug either in the rear of the headlight or under the gas tank area. 3. Mount the new speedometer in the desired location. 4. Locate the OEM wire for the high beam indicator light. Connect it with the blue wire from the wire harness on the speedometer. Connect the blue/black wire from the speedometer to ground. 5. Locate the OEM wire for the gauge illumination (back) lighting. Connect this wire to the orange wire on the speedometer. Connect the black wire on the speedometer to ground. 6. Locate the OEM wires for the turn signals. Usually they are brown and violet wires. NOTE: You will notice only one bulb for the turn signals in the gauge and two wires from the bike to the harness. If you connect both of these wires directly to the yellow wire on the speedometer, this will allow feedback and cause all the signals to flash at once. To prevent this, you will need to add a diode between each OEM turn signal wire and the yellow wire coming from the speedometer. We recommend that you utilize a Dyna tach adapter, Part #D-101, available separately. This tach adapter includes the diodes necessary to allow the turn signal indicator light to operate correctly. Follow the instructions for the tach adapter, substituting the wires from the original wire harness found in step 6 for the two ignition terminals shown in the wire schematic. Hook the white wire on the tach adapter to the yellow wire for the turn signal indicator on the speedometer. If you use the D-101 adapter, skip steps 7-9 and go directly to step 10. 7. Take one of the diodes, making sure to observe the correct polarity, and attach it to the brown turn signal wire on the bike. 8. Take the remaining diode, again making sure to observe the correct polarity, and attach it to the violet turn signal wire on the bike

Incoming search terms:

HARLEY DAVIDSON VRSC BRACKET FOR BILLET HEADLAMP SHELL REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
REMOVAL VRSCA Models 1. Remove windshield (if equipped). Refer to appropriate Instruction Sheet for procedures. 2. Remove right side cover and maxi-fuse. Refer to MAXI- FUSE in Service Manual. 3. See Figure 1. Disconnect headlamp connector (1) from vehicle wire harness. 4. Remove two screws (2), headlamp mounting bracket (3), and headlamp assembly (4) from upper bracket. 2 3 4 5 1 is03046 1. Connector 2. Screw (2) 3. Bracket 4. Headlamp assembly 5. Screw (2) Figure 1. VRSCA Headlamp Assembly VRSCB Models 1. Remove windshield (if equipped). Refer to appropriate Instruction Sheet for procedures. 2. Remove right side cover and maxi-fuse. Refer to MAXI- FUSE in Service Manual. 3. See Figure 2. Disconnect headlamp connector (1) from vehicle wire harness. 4. Remove two screws (2), headlamp assembly (3), and headlamp mounting bracket (4) from upper bracket. 5. Remove nut (5), screw (6), and trim ring (7) from head- lamp. 6. Remove lens assembly (8) from headlamp shell (9). Save lens assembly for Billet Headlamp Shell Kit 67704-03 installation INSTALLATION 2004-Earlier VRSCA and VRSCB Models 1. Assemble Chrome Billet Headlamp Shell Kit (67704-03). Refer to Instruction Sheet-J03018. NOTES VRSCA models use Headlamp 68297-05, while VRSCB models use original equipment lens assembly (including gasket and boot). Adapter ring from kit (Figure 6, Item 1) will be used to install billet headlamp assembly on Instruction Sheet-J03018. 2. See Figure 3. Cut the two connectors (1) from existing headlamp wire harness (2). Be sure to cut the wires as close to the back of the connector as possible. 3. See Figure 6. Route new wire harness (2) through the hole in bottom of the billet headlamp shell (A). NOTE Only one 16 AWG wire will fit into pin terminals included in kit. Both black wires (ground) can be joined together, then connected to a single wire, if desired. 4. Tape end of one black wire with electrical tape and secure it to wire harness. 5. See Figure 3 and Figure 6. Install terminal pin (3) and socket housing (4) onto new wire harness (Figure 6, Item 2). Refer to MULTILOCK ELECTRICAL CONNECTORS in Service Manual for installing socket/pin terminals. 3 4 1 2 is03025 1. Connector (2) 2. Wire harness 3. Terminal pin (4) 4. Socket housing Figure 3. 2004-Earlier VRSCA and VRSCB Headlamp Wire Harness 2005-Later VRSCA and VRSCB Models 1. Assemble Chrome Billet Headlamp Shell Kit (67704-03). Refer to Instruction Sheet-J03018. NOTES VRSCA models use Headlamp 68297-05, while VRSCB models use original equipment lens assembly (including gasket and boot). Adapter ring from kit (Figure 6, Item 1) will be used to install billet headlamp assembly on Instruction Sheet-J03018. 2. Disconnect and discard existing wire harness. 3. See Figure 6. Connect new wire harness (2) to billet headlamp shell (A). 4. Route wire harness (2) through hole in bottom of billet headlamp shell (A) before installing socket housing (4) provided in kit

Incoming search terms: