harley ultra classic problems

You search Auto repair manual PDF harley ultra classic problems, if there are search results will appear below. If search results do not exist, please search by others keyword.



  harley ultra classic problems Direct Download speed 5282 Kb/s

  harley ultra classic problems Full Version speed 6162 Kb/s



HARLEY DAVIDSON ULTRA CLASSIC AND ELECTRA GLIDE CLASSIC TOUR PACK ADJUSTMENT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
1. Open the Tour Pack and remove all of the contents. 2. Remove map bag and inner pack liner. Pack liner comes out quite easily once map bag is removed. 3. Remove the 4 bolts inside the tour pack that are located on top of the metal support plate that hold the tour pack to the luggage rack. Have your assistant hold the pack in place before removing the last bolt. 4. Gently tip the tour pack forward to expose the supporting luggage rack under the pack. 5. While your assistant holds the pack up, place the two adjusting bars on top of the supporting luggage rack. Use the 4 flat head screws supplied with the kit to mount the bars snugly to the support rack (see fig. 1). 6. Reposition the tour pack over the threaded holes in the adjusting bars at the 2″ or 3″ position and bolt it in place snugly (see fig. 2). 7. Replace the trunk liner and map case and the installation is complete

Incoming search terms:

Harley Davidson FL series Electra Glide, Ultra Classic, Road King, Road Glide Left and Right Mounting Plate Installation Installation Manual

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove existing control arm end cap and grind the outside flush. See picture below for reference. The swing arm will drop if both sides are removed at the same time. To ease installation, complete one side before starting on the other. Note: there is a left and right. Left and right end caps shown. 2. Install mounting plate assembly 10002351 on top of the end cap using 7/16″ hex head bolt and lock washer in the bottom hole. Use the 7/16″ counter sink bolt in the top hole. Make sure the end cap is seated properly. The end cap notch should fit into the recess on the frame. The pivot arm assembly is shipped on mounting plate assembly; you may remove the pivot arm to make installation easier. 3. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. Tighten both bolts to 25 ft lbs. (Further tightening will be required after the toe in is set). 4. If you removed the left hand pivot arm assembly, remount it now, 10002575-A (pg 20) with seal, bearings (2), washer, nut, cotter pin and dust cover. 5. Repeat for right hand side. 5 Toe In Adjustment Adjustment made with the mounting plates, bolts, pivot arms, and hubs (without wheels and tires) in place

Incoming search terms:

HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

Harley Davidson Installing The Ride Time Ultra Progressive Tour Pak LED Tail Lights

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Remove the light bulbs from the tail light housing by depressing the tab on the bulb socket assembly and turning counter clockwise. Remove the bulb from the bulb socket. 2. Remove the lenses from the warp-around light fixture. These lens are held in place by a non-hardening black sealant. In addition, there are three plastic alignment tabs on the lens body that clip into the lens frame. To remove the lens, insert the supplied push Stick through the hole in the back of the light bulb housing and gently but firmly push the lens outward. This action places a stress on the alignment tabs. 3 . Using a flat blade screw driver, pry the lens away from the frame at the top, side, and bottom to release the lens alignment tabs. Go back to step 2, and use the plastic tube to push the lens outward. It may be necessary to repeat the prying process and pushing process several times to remove the lens. Note: Some users have found it useful to heat the lens area with a hair dryer to soften the adhesive. Included in this kit are: Left and Right LED modules, 1 RTQC Quick Connect Accessory Cable , 2 RTV application sticks, 1 push stick, Approximately 3 inches of shrink tube, and 1 copy of instructions. Required for installation, but not included are: A tube of Permatex RTV (available at Wal-Mart), 1/8 inch drill bit, a drill, small flat blade screwdriver, other hand tools. Window/ body sealer if required to reseat lenses can be obtained at your local glass shop. Tour Pak, Harley Davidson, Electraglide, Raod King, and Ultraglide are registered trade marks of Harley David- son. Harley Davidson does not make or endorse the use of these lights. 4. When the lens begins to emerge from the frame, grasp it at the top and bottom and pull the lens from the housing using a up and down motion. Set the lens aside . Avoid having the sealant contact other surfaces. In most cases, the lens can be reinstalled without adding additional sealant . Note: Do not use RTV to reset the lens. If sealant is needed obtain a non-hardening body/windshield sealant from your local glass shop. 6. When you are comfortable with the location of the circuit board, drill a 1/8 inch hole in the back of the light housing. This hole will be used to bring the turn signal wire from the LED module into the Tour Pak. 7. Using the supplied stick, spread a thin layer of Permatex clear RTV silicone seal along the area where the circuit board will be located. Apply a similar layer to the top of the light housing. Route the turn signal wire through the 1/8″ hole and position the circuit board in the housing. Allow the RTV to cure. 5. Test fit the LED light board in the light housing.

2000 Harley-Davidson FLHRCI Road King Classic

0

Filed Under (Harley Davidson) by admin on 03-11-2010

download
the Road King® Classic is a motorcycle with enough traditional styling to drop jaws throughout the continent. The Road King® Classic boasts laced wheels, fat white-walls and gorgeous leather saddlebags with hard inserts so they keep their shape across the long miles. Slightly narrower new handlebars provide improved ergonomics. Fender tips, tank and seat valance all boast a metal emblem. The model is available with a fuel-injected, chrome-and-black Harley- Davidson® Twin Cam 88 engine. Specifications: Engine Type: 1449 cc, 4-Stroke, Air Cooled, V-Twin Engine Bore and Stroke: 95.3 mm x 101.6 mm Valves 2 valves/cylinder Claimed Horsepower: 67 hp (50 kW) @ 5200 rpm Maximum Torque: 110 Nm (81.1 ft. lbs) @ 3100 rpm Transmission type: 5 speed Final Drive: Belt Tire – Front: 130/90-16 Tire – Rear: 130/90-16 Brakes – Front: dual 292 mm discs with 4-piston calipers Brakes – Rear: single 292 mm disc with 4-piston calipers

Harley Davidson 1990 and later HSR Choke Cable Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
The majority of HSR42/45 installations use the Harley cable. Installation is simple when the installation instructions are followed, step by step. Those steps are: • Remove the stock Harley choke cable assembly. • Remove the spring and plunger from the stock cable. • Remove the Mikuni “Starter Nut” from the HSR. • Remove the Mikuni spring and plunger from the HSR. • Install the Mikuni spring and plunger on the Harley choke cable. • Install the Harley choke cable with the fitted Mikuni spring and plunger into the HSR carburetor. • DO NOT use the Mikuni Starter Nut; discard it. • DO NOT use the Harley spring or plunger; discard them. Note: If you do not have installation instructions, you may download them from the www.mikuni.com website in the “manuals” section. If the Mikuni Starter Nut is fitted to the Harley cable, the choke plunger is held off its seat and the choke is open all the time. If the Harley spring and plunger are used, the plunger does not seal and the choke is open all the time. The result, in both cases, is very poor fuel mileage (30 mpg or less). Another possible cause of poor mileage, rough idle and fouled spark plugs is incorrect cable routing. The stock Harley choke cable is very stiff and may not be fully seated in the metal elbow at the carburetor end of its run. This condition is easily corrected. On occasion, one of these errors may have been made by someone else at another location. The unfortunate mechanic who inherits the task of correcting the rich condition, poor idle and poor fuel mileage may have no clue as to the mismatch of parts. For this reason, we include the photos and text to help you discover if your installation is correct.

Incoming search terms:

HARLEY DAVIDSON SECURITY SYSTEM KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
FL Touring models equipped with a TLE/ TLE Ultra Sidecar will require the additional installation of a Bank Angle Switch Kit (88115-03) and is available for separate purchase. See a Harley-Davidson dealer.INSTALLATION 1. Remove the original equipment (OE) Turn Signal Module (TSM) or Body Control Module (BCM) following the instructions in the service manual. 2. Install the Bank Angle Sensor (BAS) on sidecar vehicles. 3. Install the new turn signal/security module (TSSM) (7), Hands Free Security Module (HFSM) (1) or BCM (9, 11) from this kit, following the instructions in the service manual. Configure the Trike or sidecar TSSM, HFSM or BCM to “Side Car Enabled” using Digital Technician. 4. Install the Hands Free Security Module (HFSM) Antenna and antenna mount (6) if necessary, using the service manual instructions. Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) ACTUATION 1. See a Harley-Davidson dealer to activate the key fob to the TSSM, HFSM or BCM. NOTE You can activate the TSSM fob by referring to the procedure in the electrical diagnostic manual. TRIKE AND SIDECAR CONFIGURATION (FL TOURING MODELS ONLY) Only Touring Harley-Davidson Motorcycles are suitable for sidecar use. Consult a Harley-Davidson dealer. Use of motorcycles other than Touring models with sidecars could result in death or serious injury. (00040a) NOTES FL Touring Models equipped with TLE/TLE-Ultra Sidecar require the installation of a Bank Angle Sensor (88115-03). Failure to install and configure a Bank Angle Sensor may result in death or serious injury. Sidecar and Trike configuration of the security system requires the use of a Digital Technician. Consult your Harley-Davidson dealer or the sidecar or Trike service manual for complete details. On vehicles equipped with a sidecar, the security system must be reconfigured from the default solo vehicle setting to the sidecar setting

Incoming search terms:

HARLEY DAVIDSON ADVANCED AUDIO CB RADIO KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
2006 models: communication switch 77173-06 2007 models: communication switch 77173-07 2008 models: communication switch 77173-08 FLHT models will require prior installation of: •Advanced Audio AM/ FM/ CD Radio Kit (76412-06) •AM/ FM Antenna Kit (76325-06 or 76317-06) Unless one has already been fitted as part of another Advanced Audio kit installation: 2006-2007 FLHX models will require the separate purchase of: •fuel tank console (61270-98A), •tank console gasket (71294-89), •a button-head screw (3652), •nut (7964) •clip (10103 and 10120). •tank pod mounting screws (2462) quantity 3 •FLHT trim piece (52447-96) and cb pod trim badge 2008 FLHX models: •fuel tank console (61270-08) •clips (10103 and 10120) NOTE The console screws, fuel door, gasket, mounting bracket will all need to be reused. FLTR models will require the separate purchase of: •a Console Pod Assembly (77136-03), and •three pan-head screws (2462). NOTE See a Harley-Davidson dealer for availability of optional decorative inserts for the Console Pod Assembly. ALL models will require the additional purchase of: •a Non-Ultra Overlay Harness (70169-06), and EITHER : •a Premium Stereo Helmet Headset (77147-98) OR a Hand-Held CB Microphone Kit (76312-98), All of these items are available from a Harley-Davidson Dealer. If two modules are already installed on top of the radio, two Dual-LockTM mounts, (76434-06), will be needed. Models WITHOUT a Tour-Pak installed will require the additional purchase of a Frame Mount CB Antenna Kit (76415- 06). Models WITH a Tour-Pak installed will require the additional purchase of a Tour-Pak Mount CB Antenna Kit (76414-06). All of these items are available from a Harley-Davidson Dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Electrical Overload It is possible to overload your motorcycle’s charging system by adding too many electrical accessories. If your combined electrical accessories operating at any one time consume more electrical current than your vehicle’s charging system can produce, the electrical consumption can discharge the battery and cause vehicle electrical system damage. See a Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories, or for necessary wiring changes. (00211b)

Incoming search terms:

Harley Davidson Electra Glides, Ultra Vent (model LV-2,3,4) Installation Manual

0

Filed Under (Harley Davidson) by admin on 07-03-2012

download
Remove the fairing lower from the engine guard using the procedure provided in your Harley-Davidson user/service manual. Do not remove the glove box from the fairing. Vent Placement, Hole Drilling and Cut-Out: Caution: Place cloth or cushion underneath fairing lower to protect it from getting scratched during the following procedures. LV-2,3,4 Installation Copyright 2003-2004 2 3. Working inside the fairing and using the bottom of the glove box as a guide, position a closed vent parallel to and no more than 1/16″ from the rear edge of the fairing. Position the assembly so that the vent side tabs are no more than 1/8″ below the bottom of the glove box. (You want the vent assembly as close as possible to the glove box but with enough room so that the side tabs do not touch the glove box when the vent is closed! ) Mark the back two holes with a pencil then remove the vent and replace it with the cutting template in the exact same location. See photo to the right to assist in judging the cutting template orientation. 4. Lift out the glove box, steady the template with one hand and using an 11/64″ drill bit carefully drill 1 hole near the back edge of the fairing through the bottom corner hole of the cutting template. Install one screw and nut and tighten slightly to stabilize the template’s location. On the other corner (same edge) , drill the second hole. (You cannot drill the remaining holes from inside the fairing because the front edge of the fairing lower is in the way. ) 5. Remove the screw and nut and re-position the cutting template on the outside of the fairing with the three hole side of the template towards the front of the fairing (away from the edge of the fairing) . Install two screws and nuts into the open holes. Drill the remaining two corner holes and install two screws and nuts. Change drill bit size to 1/8″ to drill the final center latch hole. Next skip down to one of the two following procedures to make the vent opening using either A) Dremel tool/RotoZip router or B) coping saw/frameless hacksaw

HARLEY DAVIDSON ADVANCED AUDIO XM SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
this kit fits 2006 and later FLHT (Electra Glide®), FLHTC (Electra Glide Classic), FLHTCU (Ultra Classic® Electra Glide), FLHX (Street GlideTM) and FLTR (Road Glide®) model motor- cycles. XM satellite radio is available within the continental United States. It is not available in Alaska or Hawaii. Additional Parts Required FLHT models will require prior installation of an Advanced Audio AM/ FM/ CD Radio Kit (Part Number 76412-06) and an AM/ FM Antenna Kit (Part Number 76325-06 or 76317-06). Unless one has already been fitted as part of another Advanced Audio kit installation: FLHT, FLHTC, and FLHX models will require the additional purchase of a Non-Ultra Overlay Harness (Part Number 70169- 06) and a left-hand Antenna Bracket (Part Number 76456-06). FLHTCU models will require the additional purchase of an Ultra Overlay Harness (Part Number 70164-06) and a left-hand Antenna Bracket (Part Number 76456-06). FLTR models will require the additional purchase of a Non- Ultra Overlay Harness (Part Number 70169-06) and an Antenna Bracket (Part Number 76316-06). If two modules are already installed on top of the radio, two Dual-LockTM mounts, Part Number 76434-06, will be needed. These items are available from a Harley-Davidson Dealer INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. 2. Remove the outer fairing and windshield. Refer to OUTER FAIRING/ WINDSHIELD REMOVAL in the Service Manual. NOTE If another module has been installed in the location reserved for the XM radio module, relocate that module per the instructions supplied with that kit

Incoming search terms: