hayabusa f1

You search Auto repair manual PDF hayabusa f1, if there are search results will appear below. If search results do not exist, please search by others keyword.



  hayabusa f1 Direct Download speed 5282 Kb/s

  hayabusa f1 Full Version speed 6162 Kb/s



2008 SUZUKI GSXR1300 Hayabusa Front Brake Line Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 09-01-2011

download
Step 1: Identify the key components that complete our brake line kit: You should have two (2) hoses, one (1) double banjo bolt, and two (2) single banjo bolts. There are also a total of nine (9) washers. Seven (7) will be used, and two (2) are spares. We strongly suggest having a professional mechanic install these brake lines, and all other installations void warranty. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: After drying out the OEM brake system, uninstall stock hoses. Take note of how the stock system was routed in case you need to re-install it. Please note there is a plastic shield on the lower triple clamp of your machine; we took this piece off to ease installation. Remove the OEM hose holder, and keep the bolt for later use. (See picture C) Step 4: Install the right and left (to your right and left as you sit on the bike) lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Double banjo hex, washer, straight banjo labeled for right line, washer, 12-degree banjo labeled for left line, washer, master cylinder. Please see picture A for reference! Double banjo bolts must be torqued at 12 FT pounds. Step 5: Route both brake lines through the enclosed c-clip, and attach to the lower triple clamp using the bolt from the OEM holder. (See picture B) Drop the lines down and thread the single banjo bolts at each caliper using the following sequence: single banjo hex, washer, 20-degree banjo, washer, thread into caliper. Torque banjo bolts to 12 FT pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions

Suzuki 240 Hayabusa Swingarm Installation Instructions

0

Filed Under (Suzuki) by admin on 12-02-2012

download
installation Instructions 1.) Stock Component Removal To begin installing this kit it is necessary to raise the rear end of the bike using a suitable hoist. Be sure to keep the bike centered on the front wheel to keep the bike from tipping over. Once you have the bike lifted and properly secured, begin with the removal of the following stock components ( For detailed information on the removal of these parts, please consult your factory manual) : 1.) Muffler or mufflers 2.) Left side and lower body panels 3.) Voltage regulator (08 model only) 4.) Front sprocket cover 5.) Front sprocket 6.) Chain 7.) Rear Axel, wheel and brake assembly 8.) Pivot tube and swingarm
2.) New Swingarm Installation A. Most of the pieces needed are installed on the swing-arm. You’ll need to install the shock mount block with the 4 supplied flat head 5/16″bolts, use red loctite and torque to 25 ft lbs. B. Insert the 2 supplied pivot bushings in the pivot tube. Move your new swingarm into position. Once you have the swingarm in position reinsert the pivot tube to hold it in place. C. On some bikes (07′ and earlier Busa’s) it is necessary to grind approximately 1/8″ off the frame for chain clearance. Not all bikes will require this, but it is best to mock up and test fit before final assembly.

Incoming search terms:

SUZUKI Hayabusa, GSXR 1000, GSXR 750, GSXR 600 Sport Brake Lever INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 21-02-2012

download
Before you install your new ASV brake lever, you MUST choose the correct brake light switch tab to install. You will find in the package with this lever one plastic bag with four smaller bags inside of it. One bag has two small phillips screws. The other three bags have small black aluminum blocks (light switch tabs) with labels on them. Part# BRC511-H is ONLY for HONDA motorcycles. Part# BRC511-STK is for all SUZUKI, TRIUMPH and 05-06 KAWASAKI ZX636R motorcycles ONLY. Part# BRC511-K is for all KAWASAKI motorcycles EXCEPT the 05-06 ZX636R . Choose the correct tab for your bike and install it onto the lever as shown in photo 2b using the two small Phillips head screws provided. It is recommended that you use locktite or another type of thread locking adhesive to make sure these screws do not come loose. Be sure to tighten these screws as tight as you can without stripping them. The brake stop / light tab is required for your ASV brake lever to work properly Carefully place the lever into the master cylinder while inserting the plunger rod into the barrel hole as shown in photo 4. Install the main pivot bolt, and tighten it until it is snug against the master cylinder. Do not over-tighten, as it could cause the lever to bind in the master cylinder

SUZUKI GSX-R1300 / HAYABUSA Fuelpak Connectors INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 15-02-2012

download
Remove the main seat and passenger seat. 2. Use a prop to hold the tank up in the trunk area. 3. Disconnect the main wiring harness from each of the lower injectors. (Fig 1) 4. Lay the Fuelpak unit in the tail section and route the wire harness down the left side of the motorcycle toward the throttle bodies. 5. Plug the Fuelpak wiring harness in line of the stock wiring harness and injectors. (Fig 2) 6. Locate the throttle position sensor connector on the right hand side of the throttle body. 7. Install the Fuelpak wiring harness TPS connectors in line of the stock wiring harness. (Fig 3) 8. Attach ground wire to the negative side of the battery. 9. Install Fuelpak in the tail section using the supplied velcro. (Fig 4) 10. Bolt the fuel tank back into place. INSTALLATION INSTRUCTIONS FOR P/N 62009 READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION FUEL INJECTION

EDELBROCK NITROUS SYSTEM UNIVERSAL MOTORCYCLE NITROUS SYSTEM

0

Filed Under (Suzuki) by admin on 26-11-2010

download
Wiring Diagram #1 Wiring Diagram #2 Red Red Red Red Black Black Black Black Black Black Factory Harness to Horn Factory Harness to Horn Horn Horn Nitrous Solenoid Nitrous Solenoid Switch Switch Bottom View Bottom View +12V with Key On From Horn Button (Ground when button is pressed) From Horn Button (Ground when button is pressed) To Nitrous Bottle To Nitrous Bottle To Nitrous Nozzle To Nitrous Nozzle Install Relay for OPTIONAL RPM Activated Switch Here. See Section 7.0 for More Details. Install Relay for OPTIONAL RPM Activated Switch Here. See Section 7.0 for More Details ©2007 Edelbrock Corporation Brochure #63-71940 Catalog #71940 Rev. 2/07 – DC/mc Page 4of 4 To Nitrous Bottle To Nitrous Nozzle Nitrous Solenoid To Starter Solenoid Switch Bottom View Ground Starter Button +12V when Pushed Install Relay for OPTIONAL RPM Activated Switch Here. See Section 7.0 for More Details. Wiring Diagram #3 Starter Button Activation for Suzuki Hayabusa 7.0 – WIRING MSD 8950 RPM SWITCH NOTE – This is a suggested wiring application. There are many ways that the RPMswitch may be installed. The installer needs to set RPMswitch to proper RPM and test operation. Use diagrams on page 3 for relay terminal #30 connection. Nitrous Solenoid To Nitrous Bottle To Nitrous Nozzle RPM ACTIVATED SWITCH 10,000 Desired RPM Chip Here Connect as Outlined in Wiring Diagrams White to 4-Coil Tach Adapter #T-101-MSD Black Battery Ground Yellow – N/C Gray – OFF When Set RPMis Exceeded Connect as Outlined in Wiring Diagrams NOTE – RPM Chips are Ordered Separately Red to Switched +12 Volt Tailight Power or any Other +12 Volt Source with the Key On Note – This Method Will Turn the Nitrous Off When Set RPM has Been Exceeded. 85 87A 30 86 87 A Test Light Can Be Used Here to Check Operation 8.0 – OPTIONAL PRODUCTS FOR EFI MOTORCYCLES A Progressive Timing Retard Controller is available from Schnitz Racing for fuel injected motorcycles. The EFIR Series Timing Retard Controllers can be used with or without a Power Commander installed.

Incoming search terms:

MPS Sport Bike Auto Shift Installation Manuals

0

Filed Under (Suzuki) by admin on 21-02-2012

download
The first thing to do is remove the seat, fuel tank, and possibly the front fairing if equipped. You will need plenty of room to work. Electrical Connections – You will need to locate and test a few things on your bike before you start wiring. A good ground, an ignition switched 12 volt power source, the horns, and the ignition coils. We have plug n play style harnesses available for some bikes. Check the web site for specific models. Control Box Wiring Coils – Most four cylinder motorcycles use either a individual firing system or a waste spark system. Waste spark is by far the most common. All four cylinder bikes with only two coils use a waste spark system. Most late model four cylinder sport bikes use waste spark systems even though they have four individual coils. Bikes with a waste spark systems will need the 360 calibrated unit. The 360 calibrated Sport Bike Autoshifts are identified by the 360 engraved into the box below the wire lead exit. The P/N for these boxes has the 360 as a suffix. (P/N 1-0299-360) Some of the newest fuel injected bikes (Hayabusa, GSXR1000, ZX12) that have cam sync sensors are individual firing. These bikes will require 720 calibration and will have no outside identifiers and the P/N 1-0299. The Sport Bike Auto Shift has four brown wire leads that are connected to the negative of each individual coil on a four coil system. You will notice that the connector for the four brown wires has a molded in ridge that marks the brown wire that is used as the rpm sensor. This must be connected to the number one cylinder coil negative wire.