hero slender carburator cleanings

You search Auto repair manual PDF hero slender carburator cleanings, if there are search results will appear below. If search results do not exist, please search by others keyword.



  hero slender carburator cleanings Direct Download speed 5282 Kb/s

  hero slender carburator cleanings Full Version speed 6162 Kb/s



HERO HONDA CD100 CHHEDA ELECTRICALS & ELECTRONICS INSTALLATION

0

Filed Under (Honda) by admin on 13-11-2011

download
These are intelligent CDI’s using variable-advanced timing where the firing angle is varied according to the engine RPM in order to maximise both the power output as well as the engine efficiency.
Built with the latest technology and infrastructure to offer high reliability and superior performance.

HERO HONDA CD-100 / SS100 / SLEEK / SPLENDOR / PASSION

0

Filed Under (Honda) by admin on 14-11-2011

download
1500 91255-169-003 30-42-11 FRONT FORK SEAL (S/S) (SLEEK) Improved Quality 200 20 PCS
1500A ————— SET OF 2 PCS FRONT FORK DUST SEAL (S/S) 100 10 PCS 1501 90756-198-000 7-37-7.5 FRONT FORK TRIPLE (COLLER) (CD-100) 200 20 PCS 1502 91202-302-01013.8-24-5 KICK SHAFT 200m20 PCS 1502A 91202-302-010m13.8-24-5+1514 KICK SEAL(SPL.GRADE O.E TYPE) MATERIAL WITH PUCH ROD RUBBER 100 10 PCS 1503 91205-350-000 6-25-6 CLUTCH 200 20 PCS 1504 91202-GK4-722 18.9-30-5 MAGNET
200

Incoming search terms:

HONDA GL1500 Headlamp Adjustments Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
Headlamp Adjusting Procedure Tools needed • Long, slender #1 Phillips screwdriver (for adjusters behind the rubber plugs) • #2 Phillips screwdriver (for the other adjuster screw) • 12-inch square of cardboard • Flat wall or garage door • Paper, tape, marker NOTE: All adjustments are very fine. You have to turn the screws A LOT to see changes in adjustment. This procedure is best done after dark, because you will need to do some test rides. Preparation 1. Set the bike on its center stand, 10 feet away from an unobstructed wall or garage door, and square to the wall or door. 2. Remove the front fairing cover and lower vent grille to gain access to the headlamp adjusters. 3. Idle the engine or connect a battery charger to the battery, to prevent battery drain. Headlamp assembly viewed from the front, showing positions of mirrors and adjusters (pretend the lens has been removed) . Low Beam Vertical Alignment 1. With the lights on low beam, cover the right half of the lamp assembly with the cardboard square, so only the left bulb is shining on the wall. 2. Using a marker, mark the top of the left low beam on the wall (use paper taped to the wall if you don’t want to mark the wall itself) . 3. Move the cardboard so it blocks the left bulb, so only the right bulb is shining on the wall. 4. The top of the right low beam should be even with the mark you made for the left low beam. If it’s not, adjust by turning the screw behind the rubber plug at the top of the lamp assembly, using a long, slender #1 Phillips screwdriver. 5. Move the cardboard back and forth between the bulbs to verify that the low beams are at the same height. On high beam, the two hotspots should line up vertically. High Beam Vertical Adjustment 1. With the lights on high beam, note the position of the beams’ hot spots on the wall in relation to the mark you made in step 5 above. 2. Most owners complain about their low beams being too low on the roadway. To correct this, lower the high beams by turning the screw behind the rubber plug at the bottom of the headlamp assembly, using a long, slender #1 Phillips screwdriver. You can watch the high beam hot spot being lowered on the wall in relation to the mark you made. 3. Take a test ride. Get out on a dark street, and adjust the high beams using the dash knob until you like what you can see. Then switch to low beam and see how that looks. 4. Repeat these steps until you get the low beam pattern you want. Left/Right Adjustment 1. Back to the wall. Set the bike on its center stand at a distance of 25 feet from the wall and square to the wall. Center the front wheel. 2. Shine the high beams on the wall. 3. Step to the back of the bike, and level your eye with the center of the passenger backrest. Use the center of the backrest and the center of the windshield like a gunsight. The center of the hotspot of the high beam should hit the wall in this line. 4. Adjust by turning the uncovered screw at the bottom of the headlamp assembly, using a #2 Phillips screwdriver.

Incoming search terms:

WAAREE A -1 4 T20W40 OIL 4 stoke Motorcycle Engine Oil

0

Filed Under (Tips and Review) by admin on 16-11-2010

download
APPLICATION •Designed for all high power 4 Stroke Motorcycle & Scooters •Recommended for use in 4 Stroke Motorcycles & Scooters of Hero Honda, Bajaj, TVS, Yamaha, Suzuki, LML & all other makes where OEM is recommending 20w40 Oil. BENEFITS •Excellent heat resistance capability to ensure more power for greater pick up •Excellent Enginecleanliness, outstandingthermal & oxidation stability to help fight deposit formation leading to longer drain intervals and excellent fuel efficiency. •Excellent Valve Train Wear Performance & High Temperature characteristics ensuring longer engine life •Excellent formulation to handle the different requirements of three critical zones of 4 stroke Motorcycle engines , Gear and Clutch. PERFORMANCE STANDARD •API SM*(*VTW ONLY) •JASO-MA2 TYPICAL PRODUCT DATA CHARACTERISTICS WAAREE A1 4T 20W40 KV, cSt @ 1000C 14.80 VI , min 115 Flash Point (COC) c0Min 236 TBN mg KOH/g Min 7.40 Pour Point 0 C Max -21 (These are typical figures and do not constitute a specification