hond trx 90 will not run unless the choke is on

You search Auto repair manual PDF hond trx 90 will not run unless the choke is on, if there are search results will appear below. If search results do not exist, please search by others keyword.



  hond trx 90 will not run unless the choke is on Direct Download speed 5282 Kb/s

  hond trx 90 will not run unless the choke is on Full Version speed 6162 Kb/s



Harley Davidson 1990 and later HSR Choke Cable Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
The majority of HSR42/45 installations use the Harley cable. Installation is simple when the installation instructions are followed, step by step. Those steps are: • Remove the stock Harley choke cable assembly. • Remove the spring and plunger from the stock cable. • Remove the Mikuni “Starter Nut” from the HSR. • Remove the Mikuni spring and plunger from the HSR. • Install the Mikuni spring and plunger on the Harley choke cable. • Install the Harley choke cable with the fitted Mikuni spring and plunger into the HSR carburetor. • DO NOT use the Mikuni Starter Nut; discard it. • DO NOT use the Harley spring or plunger; discard them. Note: If you do not have installation instructions, you may download them from the www.mikuni.com website in the “manuals” section. If the Mikuni Starter Nut is fitted to the Harley cable, the choke plunger is held off its seat and the choke is open all the time. If the Harley spring and plunger are used, the plunger does not seal and the choke is open all the time. The result, in both cases, is very poor fuel mileage (30 mpg or less). Another possible cause of poor mileage, rough idle and fouled spark plugs is incorrect cable routing. The stock Harley choke cable is very stiff and may not be fully seated in the metal elbow at the carburetor end of its run. This condition is easily corrected. On occasion, one of these errors may have been made by someone else at another location. The unfortunate mechanic who inherits the task of correcting the rich condition, poor idle and poor fuel mileage may have no clue as to the mismatch of parts. For this reason, we include the photos and text to help you discover if your installation is correct.

Incoming search terms:

2003 – 2005 Matrix WIND NOISE FROM DOOR GLASS WINDOW RUN REPAIR

0

Filed Under (Toyota Manuals) by admin on 28-10-2011

download
NOTE: Use the same procedure for the LH side as the RH side. 1. Place the window in the down position. 2. Remove the window run. Completely remove the double-sided tape remaining on the frame. 3. Thoroughly clean the door frame using a white body shop towel and Kent Acrysol. NOTE: Do NOT use red shop towels. These towels contain silicone. 4. Install the door glass window run. A. Position the glass run at the No. 2 and No. 3 corners of the door frame and then attach the middle part of the run. B. Insert the glass run into the window run channels. NOTE: Do NOT apply water or lubricant to the glass run when inserting it into the door. Make sure the glass run fits securely into the holes of the door frame

Incoming search terms:

HONDA TRX 650 RINCON 4X4, TRX 680 Rincon BLADE HARDWARE MOUNTING REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Honda) by admin on 26-12-2011

download
Push tube/ Swivel/ Blade Assembly Instructions 1. Install the blade swivel (15) onto the front of the push tube (14) using the 1/2″ shoulder bolt (4), two 1/2″ washers (5), and a 3/8″ Nylock nut (3) from the bolt bag per diagram #1. Make sure the flat washers seat properly on the bottom of the shoulder bolt while tightening the nut. Make sure the blade turns freely. 2. Remove the 2 bottom flanged nuts (I) from the u-bolt (D) and 2 from the 3/8″ bolts (H) on the blade position pin assembly (23). Run the 2 top flanged nuts up the threads of the u-bolt. Place the blade position pin assembly on the push tube as shown in the Diagram, sliding the blade position pin through one of the oval holes on the swivel and through the rear blade position pin support bracket on the push tube. 3. Re-install the u-bolt and 3/8″ bolts and flanged nuts per the Diagram. On the u-bolt, thread the bottom nuts up until they are flush with the bottom of the threads then run the top ones down, making sure the bottom nuts remain flush with the bottom of the u-bolt. Tighten all 4 bottom nuts. 4. Remove the two shoulder bolts (18) from the pivot point brackets on the back of the blade (1). Attach the blade to the swivel by sliding the ears on each side of the swivel into the pivot point brackets on the blade, reinstall the two shoulder bolts and Nylock nut (3) and tighten. 5. Hook the blade springs (6) to the two round holes on either side of the 5 oval holes on the swivel. Hook the eyebolts through the other end of the springs, push the eyebolts through the spring attaching points on the back of the blade and install 3/8″ Nylock nuts (3). Spring tension may be increased by tightening both Nylock nuts on the eyebolts evenly. 6. Install the blade stops (16) with the two 3/8″ x 1″ bolts (17) and 3/8″ nuts (3) per the Diagram. Rotating the stops allows you to change the blade pitch to suit changing conditions or materials

Incoming search terms:

HW Prowler Carburetor Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
1. Remove both seats and the plastic seat pans under the seats. 2. Remove the engine cover 3. Remove the air-box by removing the cross-bar support that runs under the air-box to the framing on each side by the seat framing and disconnect the air box from the carburetor and from the plastic intake in the rear. 4. Disconnect the engine breather hose from the bottom of the air box 5. Set the air-box to the side 6. Disconnect the plug going to the stock carburetor, this is the electronic choke. Wrap the end left on the vehicle with electrical tape. 7. Cut the fuel line just above the fitting on the passenger side of the carb 8. Remove the side cover off the drivers side of the carb where the throttle cable goes in, see fig. #1 9. Pull the throttle cable out and then remove the throttle cable end from the throttle plate See Fig. #2 10. Loosen the clamp on the rear of the carb holding the carb on 11. Pull the carb out of the intake boot 12. Set OE carb to the side. 13. Push the new Carb into the intake boot making sure the carb is perfectly vertical and then tighten the clamp back up. The new carb is slightly larger than the stock one so some additional pressure will be needed to get it in. 14. Route all the breather lines connected to the carb down under the carb. 15. Connect the throttle cable onto the new carb but putting the cable end in the bottom hole of the throttle plate on the passenger side of the carb allowing the cable to ride in the slot in the plate and then turn the throttle plate clock wise allowing the threaded end of the cable to fit into the lower round hole of the throttle cable connection plate. See Fig. #3 16. Make sure you have a nut on each side of the plate turn the nut on the outside of the plate to take up the slack in the throttle cable then tighten the nut on the inside of the plate. See Fig. #3 17. Push the fuel line onto the fuel inlet on the passenger side of the carb and install the supplied clamp to hold it on. The fuel line will be a little hard to push on. 18. DO NOT ATTEMPT TO INSTALL THE CHOKE CABLE PARTS SUPPLIED IN THE KIT UNTIL AFTER THE CHOKE CABLE ITSELF IS INSTALLED AND READY TO SCREW INTO THE CARBUETOR. 19. To install the supplied choke cable, drill a 3/8″ hole in the dash on the left side of the steering wheel in a location convenient to your left hand. 20. Remove the plastic nut from the bottom of the choke handle on the choke cable. 21. Push the choke cable thru the hole you drilled and then slide the nut over the cable to the inside of the dash and reinstall back on the back of the choke mechanism. Some dash screws maybe needed to be removed to accomplish this

Incoming search terms:

2008 KTM 50 SX JUNIOR 50 SX OWNER'S MANUAL

0

Filed Under (KTM) by admin on 22-10-2010

download
Choke Dell’Orto carburetor PHVA 14 DS (50SXJunior) Choke lever [1] is mounted to the right side of the carburetor. If you move the choke lever up to the stop, a hole is opened in the carburetor through which the engine can draw in additional fuel. This results in a “rich” fuel-air mixture required for a cold start. Moving the choke lever back closes the hole in the carburetor again. Choke Dell’Orto carburetor PHBG 19 BS (50 SX) Choke control knob [2] is mounted to the left side of the carburetor. If you pull the choke control knob up to the stop and turn it 90º, a hole is opened in the carburetor through which the engine can draw additional fuel. This results in a “rich” fuel-air mixture required for a cold start. Turning back the choke control knob returns the knob to the starting position and closes the hole in the carburetor again. Kickstarter The kickstarter is mounted on the right side of the engine. Its upper part can be swivelled. Foot brake lever The foot brake lever is located in front of the right footrest. The basic position can be adjusted to the seating position (see maintenance work). Side stand (50 SXJunior) Use your foot to swing the side stand forwards to the stop. Make sure it rests securely on solid ground.

HONDA CRF250X OWNER'S MANUAL

0

Filed Under (Honda) by admin on 01-12-2010

download
Always follow the proper starting procedure described below. Your motorcycle can be kickstarted wirh the transmission in gear by pulling in the clutch lever before operating the kickstarter. Preparation Make sure that the transmission is in neutral. Turn the fuel valve ON. Fuel Valve Starting Procedure Always follow the proper starting procedure described as follow. 4. Warm up the engine; don’t operate the throttle. 5. About 15 seconds after the engine startes, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. High Air Temperature 35°C (95°F) or above 1. Do not use the choke. 2. Keep the throttle fully closed. 3. Start the engine following step 3 under Normal Air Temperature. Low Air Temperature 10°C (50°) or below 1. Follow steps 1-4 under Normal Air Temperature. 2. Continue warming up the engine until it runs smoothly and responds to the throttle when the choke knob is pushed back all the way to fully OFF. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. Hot Engine Starting 1. Pull the hot start lever (3) and start the engine following step 3 under Normal Air Temperature. 2. As soon as the engine starts, release the hot start lever. NOTICE NOTICE Basic Operating Instructions 15 (1) fuel valve The three-way fuel valve is used to control the flow of fuel from the fuel tank to the carburetor. ON -Turning the fuel valve ON before attempting to start the engine allows fuel to flow from the fuel tank to the carburetor. OFF -Turning the fuel valve OFF after stopping the engine prevents the flow of fuel from the fuel tank to the carburetor. RES -Turning the fuel valve to RES allows fuel to flow from the reserve fuel supply to the carburetor. (1) fuel valve (2) choke knob Check the engine oil, transmission oil and coolant levels before starting the engine (pages 44,47,48). To restart a warm engine, follow the procedure for ”High Air Temperature. ” Normal Air Temperature 10°C-35°C (50°F-95°F) 1. Pull the choke knob (2) up all the way to fully ON, if the engine is cold. 2. Keep the throttle fully closed. 3. Pull the clutch lever all the way in, and press the starter button with the throttle completely closed. Or operate the kickstarter to start the engine. Starting from the top of the stroke, kick through to the bottom with a rapid, continuous motion. Do not operate the throttle. Allowing the kickstarter to snap back freely against the pedal stop can damage the engine case.

Incoming search terms:

2005 Honda CRF450X OWNER'S MANUAL AND COMPETITION HANDBOOK

0

Filed Under (Honda) by admin on 04-12-2010

download
Starting & Stopping the Engine Always follow the proper starting procedure described below. Your CRF can be started with the transmission in gear by pulling in the clutch lever before operating the kickstarter or start button. Preparation Make sure that the transmission is in neutral. Turn the fuel valve ON. Fuel Valve Starting Procedure Always follow the proper starting procedure described as follow. 5. Warm up the engine; don’t operate the throttle. 6. About 15 seconds after the engine starts, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. HighAirTemperature 35°C (95°F) or above 1. Turn the fuel valve (1) ON. 2. Do not use the choke. 3. Keep the throttle fully closed. 4. Start the engine following step 4 under “Normal Air Temperature.” LowAirTemperature 10°C (50°) or below 1. If the temperature is below 32°F (0°C), open the throttle two or three times. (The engine requires a richer mixture for starting in cold weather. When the throttle is so opened, the accelerator pump will feed extra fuel to the cylinder, thereby facilitating starting in cold weather.) 2. Follow steps 1-5 under “Normal Air Temperature.” 3. Continue warming up the engine until it runs smoothly and responds to the throttle when the choke knob is pushed back all the way to fully OFF. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. (cont’d) NOTICE NOTICE Basic Operating Instructions 15 (1) fuel valve The three-way fuel valve is used to control the flow of fuel from the fuel tank to the carburetor. ON -Turning the fuel valve ON before attempting to start the engine allows fuel to flow from the fuel tank to the carburetor. OFF -Turning the fuel valve OFF prevents the flow of fuel from the fuel tank to the carburetor. RES -Turning the fuel valve to RES allows fuel to flow from the reserve fuel supply to the carburetor. (1) fuel valve (2) choke knob Check the engine oil, transmission oil and coolant levels before starting the engine (pages 44,47,48). To restart a warm engine, follow the procedure for”High Air Temperature.” NormalAirTemperature 10°C-35°C (50°F-95°F) 1. Turn the fuel valve (1) ON. 2. Pull the choke knob (2) fully ON, if the engine is cold. 3. Keep the throttle fully closed. 4. Pull the clutch lever all the way in, and depress the start button. Or operate the kickstarter to start the engine. Starting from the top of the stroke, kick through to the bottom with a rapid, continuous motion. Do not operate the throttle. Allowing the kickstarter to snap back freely against the pedal stop can damage the engine

Incoming search terms:

HSR Carburetor Total Kits Installation And Tuning Manual

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
1. Disconnect the battery ground wire from the battery. 2. Turn the fuel petcock to the “OFF” position. 3. Elevate the rear of the fuel tank for better access to the carburetor area. 4. Remove the coil, horn or other devices on the left hand side of the engine to allow free access to the intake manifold bolts. 5. Remove the complete air cleaner assembly, including the backing plate. 6. Disconnect any vacuum hoses and the fuel hose from the stock carburetor. 7. Disconnect the choke cable from the frame. 8. Remove the stock carburetor. 9. Evo: remove the stock manifold. 10. Twin Cam: unplug MAP sensor, remove manifold and then remove the MAP sensor from the manifold. Installation: Intake Manifold: Twin Cam only: Install MAP sensor in Mikuni manifold. 1. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 2. Attach the rubber flange to the Mikuni manifold with the 5/16″x3/4″ bolts and washers. To ease installation, use liqiud detergent to lubricate the manifold seals. Choke: Evo: We recommend that you use the Mikuni choke cable that is furnished with the carburetor. However, you can use the stock Harley cable (’90-’99 models only) if you follow the Twin Cam choke cable instructions. Twin Cam: 1. Remove the Harley choke cable from the stock carb. 2. Remove the Harley spring and plunger from the Harley choke cable. 3. Remove the Mikuni spring and plunger from the Mikuni carburetor. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut. 6. Install the new assembly into the Mikuni. Be careful to only gently tighten the plastic nut.

Incoming search terms:

HSR Carburetor Total Kits Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Intake Manifold: 1. Install MAP sensor in Mikuni manifold (Twin Cam only). 2. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 3. Attach the rubber flange to the Mikuni manifold with the furnished 5/16″x3/4″ bolts and washers. Choke Cables: Mikuni & Harley-Davidson Route the cable with largest radius bends possible. Check the cable for free-play after installation. If there is no free-play, the engine may run rich and deliver poor performance or low fuel mileage. Harley Cable (Twin Cam Kits: 42-19, 45-4) : 1. Remove the Harley choke cable from the stock carb. 2. Remove the spring and plunger from the cable. 3. Remove the spring and plunger from the Mikuni. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut (See Figure 1). Total Kit Installation Instructions The HSR series carburetors are precise yet durable instruments; however, like any other piece of fine equipment, they require correct installation and reasonable care to assure optimum performance and long life. Extra time spent during installation will pay off in both short and long term performance and reliability. This Mikuni HSR carburetor kit is designed to be a bolt-on application, and as such, is set-up and jetted properly for most applications. However, since Harley-Davidson motors are often highly modified, alternate tuning settings may be required. The Mikuni Tuning Manual helps make jetting alterations and adjustments an easy matter. NOTE: Carburetor Kits not designated as C.A.R.B. exempt, are not legal for motor vehicles operated on public highways in the state of California, or in any other states and countries where similar laws apply. WARNING NOTE: NOTE: WARNING CAUTION NOTE: NOTE: TK-2 6. Install the new assembly into the Mikuni carburetor. Be careful to only gently tighten the plastic nut. 7. Loosen the knurled plastic friction nut behind the choke knob and check for free-play (see Figure 2). Figure 1: Harley nut with Mikuni spring & plunger Figure 2: Choke cable adjustments Mikuni Cable (Evo Kits: 42-8, 45-2 & 45-3) : 1. Remove nut, spring and plunger from the Mikuni. 2. Install the nut, spring and plunger onto the cable. 3. Install the assembly into the Mikuni HSR carburetor. Be careful to only gently tighten the plastic nut. 4. Check for free-play. Adjust the cable as necessary. An optional choke cable mounting bracket is included in the Evo kits for custom installations. Carburetor Installation: 1. Insert the carb fully into the rubber flange, align with engine and tighten the clamp. 2. Slip the fuel hose onto the carburetor’s fuel fitting and secure with the enclosed hose clamp. NOTE: Some Twin Cam installations may require removal of a small amount of fin material from the cylinders to clear the float bowl. Throttle Cables The HSR carburetor uses stock 1990 and later Harley- Davidson cables. However, if your Harley is fitted with some other carburetor, you may need to purchase a set of cables. See your dealer for the correct cable set. 1. Route the throttle cables with large radius curves and so they do not interfere with other components. 2. Screw the cable adjusters together to make them as short as possible. 3. Connect the “close” cable first (see Figure 3). 4. Install the “open” cable next (see Figure 3). 5. Adjust the opening cable until the slide can be opened fully. Snug the adjuster lock nut. 6. Turn the handlebar to the right and adjust the throttle free-play with the closing cable adjuster to approximately 1/8″ (see Figure 4)

Incoming search terms:

motorcycle Turn Signal Conversion Kit Installation Instructions

0

Filed Under (Tips and Review) by admin on 09-11-2010

download
1. Place motorcycle on solid, level ground and on center stand if equipped. 2. Remove your turn signal lens. Place it upside down and clean the lens interior with the supplied alcohol wipe. Allow to completely air dry. Note: the LEDs are mounted to the inside of the turn signal lens with the LEDs making direct contact with the lens. The supplied silicone is used to secure the LED board to the lens. It remains flexible but can be removed. Test fit the board in your lens prior to using silicone. 3. Using a small screwdriver, poke a small hole in the end of the tube of silicone. Place a dab of silicone on each of the 12 LEDs on the circuit board. CAUTION : Note the position of the metal pins on the back of the LED board, They must be located 90 degrees from where the holes are that secure the lens to the housing. See attached diagram. 4. Position the round circuit board over the inside of your turn signal lens with the LEDs facing down. Get the board as centered as possible. Allow the silicone to make contact with the inside of the lens and then push down and slightly rotate the board back and forth to allow the LEDs to make contact with the lens surface. Repeat other side. NOTE : the silicone will require 30 minutes in 70 degree weather to tack up. Full cure will occur within 24 hours. We suggest not riding for several hours if possible to allow the best adhesion. 5. You will need to access the following wires; running light (license plate can be used), brake lights, right turn and left turn. Disassemble the bike as needed to gain access to the wiring. Shop Tip: we have found that on the Yamaha Star Series and the Kawasaki Cruisers that installation is much easier when you remove the turn signal bar from the fender. On the Yamahas, there are 3 bolts holding the moustache in position. The wires will unplug from behind the license plate. On the Kawasakis, unplug the signals under the seat and bend the tabs under the fender to be able to remove the wires. 6. We have provided some tubing to slide over the wires so that when you re-install the bulb socket, our wires for the LED boards will not be pinched. This tube should be slid all the way into the turn signal housing. You may have to shorten the tubing for your installation. 7. You will need to run wires through the stem of the turn signal. You can see samples of how the various manufacturers signal housings come apart on our web site. Click on “Other Lighting Products” and then “Turn Signal Conversion Kits” and follow the link. We suggest placing the removed turn signal assembly on a towel on your work area. 7. You will need to leave 2″ of slack in the wires at the turn signal housing to allow for wire connection. 8. Reinstall the turn signal housing back on the motorcycle if removed. NOTE: both of the run/brake circuits must be used. You may shorten the wires only on the run/brake circuits as needed. Do not change the circuits under the heat shrink. T-Tap instructions. Lay the “donor” wire in the slot in the burgandy connector. Close and snap together with pliars. Strip some insulation off of the wire which will be tapping into the factory wire. Crimp one of the pink connectors on the bare wire and plug it into the burgandy T-Tap 9. Connect the green wires from the run/brake circuits to the bikes running lights. The 2 greens can be connected together. 10. Connect the blue wires from the run/brake circuits to the bikes brake lights. The 2 blues can be connected together. 11. Take one of the red wires from a run/brake circuit and connect it to one of the black with white stripe wires coming from one of the LED boards using the supplied red butt connector. Connect the other run/brake circuit red wire to the remaining black with white stripe wire on the other LED board. 12. Connect the black wire from the LED board on the right side of the bike to the right turn signal positive (+) wire on the motorcycle. 13. Connect the black wire from the LED board on the left side of the bike to the left turn signal positive (+) wire on the motorcycle. 14. Plug the wires into the LED boards. If you hold the turn signal lens so that you are viewing the back of the LED board, position the connectors on the board at the 12 o’clock (top) position. The connector on the left is the positive (+) terminal. Connect the red wire to it. Connect the black wire to the remaining connector on the right side. 15. Check operation. LEDs should come on with running lights. LEDs will brighten when brake lights are applied. LEDs will shut off when the amber turn signal comes on. 16. Should you have any problems, please see the troubleshooting chart on our website.* * 17. Reassemble bike

Incoming search terms:

Incoming search terms: