honda 400ex snorkel removal

You search Auto repair manual PDF honda 400ex snorkel removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda 400ex snorkel removal Direct Download speed 5282 Kb/s

  honda 400ex snorkel removal Full Version speed 6162 Kb/s



Honda TRX 400EX INSTALLATION And REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 14-12-2011

download
Quiet cores are supplied with this kit but not installed. To install the quiet cores remove both rear end caps ((turn downs) and install the quiet cores with the tubes facing inward. Re-install the end caps. REMOVAL Remove seat, disconnect attery and remove. Remove front fenders and side skirts. Remove fuel tank (make sure to shut fuel off and drain remaining fuel in the line before removing). Remove stock muffler first, then remove stock headers. Retain the 4 stock header bolts to install on your new exhaust system. Remove the rear bolt from your stock air box. Loosen stock intake clamp at carburetor. Remove stock boost bottle from the side of the boot. Loosen stock snorkel clamp at the air box, remove stock retaining clip at the front of the snorkel. Remove stock air box, intake boot and snorkel together from the ATV. Slide tarter solenoid off of stock mounting prongs. Remove Phillips screws from fuse holder and remove from plastic housing. Remove plastic battery housing from the ATV. Unplug tail light from harness. Unclip harness from the 2 clips above the battery. CARBURATION Now would be a good time to replace your stock main jet, with the supplied 190 main jet and replace your stock pilot jet with the supplied 48 pilot jet. Make certain that all hoses are tight and routed as stock. Be certain carb clamp is tight when re-installed. INTAKE BOOT Remove the intake boot from the stock air box. Take an exacto knife or razor blade and trim off the rubber piece that the hard plastic snorkel slips into. Trim around the intake boot staying the same distance as the rest of the lip. Take a hax saw and cut the groove as the rest of the boot is, being
careful not to cut all the way through (Picture Fig.2).

Kawasaki V-Force 700 Snorkel REMOVAL AND INSTALLATION

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove plastic from around air filter housing. Remove clamp attaching stock intake (snorkel) from air box. Loosen upper radiator hose clamp. Rotate it so the drive is on the opposite side of the new snorkel and retighten it. Loosen metal support for front plastic. Have a friend gently pull outward and carefully install the new snorkel. Position snorkel so it does not interfere with any cables or steering stem. Move handle bars back and forth. Check for clearance around new snorkel. Make sure all wires, cables and steering stem do not come into contact with the snorkel. Adjust as necessary. Tighten clamp at the air box. Reinstall plastic in opposite order of removal. At your own risk, you can cut slices in the black plastic hood on front of the quad to force the maximum amount of cold fresh air and produce additional horsepower. Jetting will vary from quad to quad and with the altitude

Kawasaki Prairie 650 Snorkel REMOVAL AND INSTALLATION

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove plastic from around air filter housing. Remove air filter housing lid and air filter. Remove 8 small screws from bottom of air box. Next, remove bolt from front and rear of air box. Remove the air box. Remove old snorkel from air box. Remove hose clamp and rubber drain tube from old snorkel. Reinstall on new snorkel. Install new snorkel vertical with the air box. Reinstall air box making certain all vacuum hoses are reinstalled. Check for clearance around new snorkel. Make sure all wires and steering stem do not come into contact with the snorkel. Adjust as necessary Reinstall filter and filter cover. Jetting depends on your elevation. A good starting point for 1000 feet and under is to remove the main jet #142 from the rear carburetor. Install it in the front carburetor. Purchase and install a #145 main jet in the rear carburetor. This works well with an aftermarket air filter and exhaust. For a very reasonable price, HMF Exhaust offers a jet kit with their exhaust that we recommend. Let them know Diamond G Racing sent you.

HONDA VTX1800R AND HONDA VTX1800N BIG SHOTS EXHAUST SYSTEM REMOVAL

0

Filed Under (Honda) by admin on 17-11-2011

download
If motorcycle is oxygen sensor equipped, unscrew the sensors from the stock exhaust system and install them
into the Vance & Hines exhaust system, being sure to install the front cylinder sensor into the lower pipe and
the rear cylinder sensor into the top pipe. Note: Use caution when handling. Do not touch sensor tip area.
2. If motorcycle is not oxygen sensor equipped, install both M12 x 11 plugs and washers (supplied)into the oxygen
sensor bosses. 3. Check condition of stock exhaust gaskets. Replace if damaged or worn. 4. Install and tighten supplied mounting bracket (stamped 345-P) in the original mounting bar location, using one M10 x 35 flange bolt and nut on top (supplied) and one M10 x 20 flange bolt on bottom (supplied) (Figure 2). Note: The bracket mounts behind the top frame mount and in front of the bottom frame mount(Figure 2).5. Install and tighten rectifier using M6x30 flange bolt, nut
and washer combinations (supplied) (Figure 2). 6. Place heat shields on a non-abrasive surface such as a blanket or carpet. Using a felt tip marker mark outside surface of front and rear heat shields with location of the mounting clips welded to the inside

HONDA CB90OC/ CB900F FUEL SYSTEM AND ENGINE REMOVAL/ INSTALLATION

0

Filed Under (Honda) by admin on 05-11-2011

download
Use geniune HONDA or HONDA-recommended parts and lubricants or their equivalent. Parts that do not meet HONDA’s design specifications may damage the motorcycle. 2. Use the special tools designed for this product. 3. Use only metric tools when servicing this motorcycle. Metric bolts, nuts, and screws are not interchangeable with English fasteners. The use of incorrect tools and fasteners may damage the motorcycle.4. Install new gaskets, O-rings, cotter pins, lock plates, etc. when reassembling. 5. When ightening bolts or nuts, begin with larger­díameter or inner bolts first, and tighten to the specified torque diagonally, unless a particular sequence is specified. 6. Clean parts in cleaning solvent upon disassembly. Lubricate any sliding surfaces before reassembly.7. After reassembly, check all parts for proper installation and operation

HONDA GL1200 fork seals Removal And Installation Manual

0

Filed Under (Honda) by admin on 27-02-2011

download
subsequent seal failure it can cause, is to cover or “shield” the tubes in some manner that goes beyond the normal protection offered by dust seals. My old CB200T has the traditional, accordion-rubber “gaiters” over the shock tubes, and the seals have failed only once in 12 years, at 80,000 miles. That’s why you still see gaiters on virtually every off-road bike made. But somewhere along the line “fashion” and “design” overcame common sense, and we all started insisting on street bikes with modern-looking, totally exposed, polished fork tubes. Gaiters were dropped almost entirely, determined to be much too old-fashioned-looking, or as contributing in some miniscule manner to fork “stiction.” Maybe so—but they worked. Some riders, wise to the ways of seal failure, have developed “home remedies” to protect their forks. Among the ones I’ve seen are sections of rubber hose attached to fork housings with hose clamps, or the more attractive addition of vinyl “wrap-arounds” that velcro around the tubes and slide up and down with the forks. Some of these are even color-matched to the bikes. I used to own a Honda GL1200 that needed the fork seals replaced at 21,000 miles, 43,000 miles, and 62,000 miles. Then I covered the exposed upper tubes with vinyl “sliders,” and never had to replace the seals again. The bike’s current owner now has the odometer up to 124,000 miles, and the seals are still holding. Honda must have gotten wise to this, because the GL1500 models came with plastic “fork shields” built right onto the front fender. Even though they don’t quite cover the entire exposed area of the tubes

Honda Motorcycle Na vigation Kit

0

Filed Under (Honda) by admin on 28-11-2010

download
Honda Motorcycle Na vigation Kit Honda Motorcycle Navigation Kit G e n e r i c A c c e s s o r i e s 2 0 0 8 For your peace of mind Honda Genuine Accessories are carefully designed, researched and stringently test ed tot he highest standards. And since they’re all Honda approved you’llknowthat they’rejustastoughand well made as your Honda motorcycle. Please Note -All prices quoted are correct at time of printing and are subject to change without prior notice. y e a r w a r r a n t y GENUINE ACCESSORIES Honda Motorcycle Navigation Kit Model Part Number Description RRP Remarks NAKED CBF 600 08A 40MER800B CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY CBF 600 08A 40MER800A CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY ON/OFF XL700V 08A 40MFF800 * CONTAINS NA VI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EARPH ONE, MANUAL, 08A 30MFF800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY XL 1000V 08A 40MBT800 CONTAINSNAVI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EAR PH ONE, MANUAL, 08A 30MBT800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY TOURERS/SPORT TOUR ERS DN-01 08A 40MEH800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, AND BATTERY -CONTAINS 08A 30MEW800 ADDITIONALSTE ERIN G HANDLE C LAMPS FORV ISU AL INTE GRAT ION OF THE COMPONENT NT700V 08A 40MEW800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, BATTERY

Incoming search terms:

2000 Honda Rancher ATV Winch Mounting Kit REMOVAL AND INSTALLATION

0

Filed Under (Honda) by admin on 13-01-2012

Begin by removing the front fascia and front skid plate on the vehicle as shown in figure 1. Save the fasteners as they will be used later to re-install the front fascia and skid plate. 2. Remove the 8mm bolts on both sides located inside the front tires and on the ends of two horizontal tubes on the front tube frame as shown in figure 2. 3. Place the mounting plate (A1) inside the front tube frame. The tabs with the slotted holes facing down. The slotted tabs should align where the
two 8mm bolts were removed in step 2. Reinstall these two bolts at this time thighten to just fingertight. Install the two 1/4-20 u-bolts (B3) and locking hex nuts (B1) and flat washers (B7) at thism time see figure 3, do not tighten down at this time. so the plate can be adjusted for position see figure 2. 4. Place the rear support bracket (A4) into position
and attach with the two 5/16-18 x 3/4 hex cap screws (B6), flat washer (B5) and locking nut (B4). Adjust the position of the support bracket so that it comes in contact with the frame tubes and tighten the fasteners see figures 3 and 4.
Make sure the support bracket maintains contact with the rear frame tubes and tighten down the two front 8mm mounting bolts. Tighten the bolts to a recommended torque of 12 ft-lb (17 N-m). 5. Attach the fairlead bracket support (A2) to the front frame tubes see figure 5. The support bracket attaches behind the front tubes. Space the bracket away from the tubes using the spacer brackets (A3). Attach the brackets using the 1/4- 20 u-bolts (B2), lock nuts (B1) and flat washers (B7). Before tightening the u-bolts make sure the bracket is in the correct position by fitting the front
fasica into postion and checking location. Tighten the nuts to a recommended torque of 7 ft-lb (10 N-m). NOTE: If this kit is being installed on a 00 to 03 Honda the wider fairlead bracket (A2) will need to be used. This will require the use of the
wider u-bolts (B3). The spacer brkts (A3) will not be required when installing the wider fairlead brkt

HONDA XR/ CRF100 120 BIG BORE KIT INSTALLATION AND REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 15-11-2011

download
nstallation of this bore kit is identical to OEM installation. Please re- fer to the Honda shop manual or a qualified machanic for assistance. Note that the larger valve relief in the piston dome is the intake side (it should be installed closer to the rear of the bike). Every effort has been made to insure the quality of this product. Because BBR cannot control the installation or use there is NO warranty or guarantee with this product. Using quality motor- cycle oil will help prolong engine life. Be sure to change it often This kit is intended for use on 1993 and newer XR/CRF100′s using CDI ignition. Engine assembly requires special attention to detail. A new BBR Cylinder and piston kit have been supplied. The following measurments are critical to proper installation and performance

1989-2000 Honda XR’S WHEEL REMOVAL AND SERVICE TOOLS

0

Filed Under (Honda) by admin on 15-12-2011

download
ATV BALL-JOINT SOCKET This tool is designed remove and install nut on Yamaha YFM350X Warrior. 35-8581 ATV Ball-Joint Wrench ATV BALL-JOINT SEPARATOR This tool is designed to separate the knuckle-ball joints on ATV’s without damage to the A-arm, ball joint stud or rubber boots. Sold as a kit with two separate press bolts to fit a variety of applications. Fits the following ATV applications: HONDA: TRX250R 86-89, TRX250X 87-88 & 90-91, TRX300EX 93-98 YAMAHA: YFZ350 Banshee 87-02, YFM350X Warrior 87-96 35-1975 ATV Ball-Joint Separator