honda 420 clutch adjustment

You search Auto repair manual PDF honda 420 clutch adjustment, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda 420 clutch adjustment Direct Download speed 5282 Kb/s

  honda 420 clutch adjustment Full Version speed 6162 Kb/s



HARLEY DAVIDSON STAINLESS STEEL BRAIDED CLUTCH CABLE KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
REMOVE CLUTCH CABLE 1. See Figure 1. Loosen clutch adjuster to obtain slack in the clutch cable (2) by performing the following: a. Locate cable adjuster (1) and slide off rubber boot (4). b. While holding cable adjuster with 1/2-inch wrench, loosen jam nut (3) using a 9/16-inch wrench. c. Turn cable adjuster until there is a large amount of free play at hand lever. 1 2 3 4 is 00889 1. Cable adjuster (1/2-inch) 2. Cable end 3. Jam nut (9/16-inch) 4. Rubber boot Figure 1. Clutch Cable Adjuster 2. See Figure 2. Remove the retaining ring (1), pivot pin (2) and clutch cable anchor pin (3) from the hand lever. 2 3 1 is 00891 1. Retaining ring 2. Pivot pin 3. Clutch cable anchor pin Figure 2. Clutch Cable Compoments 3. See Figure 3. Drain transmission lubricant and remove fill plug dipstick. Remove the six screws that hold the clutch release cover in place. Remove the clutch release cover, being careful not to damage the gasket. NOTE The clutch release cover gasket (P/N 36801-87B) will need to be replaced if torn or damaged to prevent transmission fluid from leaking from the release cover. 4 3 5 2 6 1 is 00894 Figure 3. Clutch Release Cover Screw Sequence 4. See Figure 4. Note position of retaining ring opening. Retaining ring opening must be positioned in approximately the same location during reassembly. Remove retaining ring (1). 5 4 1 3 2 is 00895 1. Retaining ring 2. Inner ramp 3. Cable fitting 4. Clutch cable 5. Ramp coupling Figure 4. Clutch Cable Connection 5. Pull inner ramp (2) and coupling (5) out of side cover. Hold inner and outer ramps together to keep balls from falling free. 6. Rotate the inner ramp to a position that will allow the coupling (5) to be disconnected from the inner ramp lever arm. Disconnect coupling from inner ramp. Disconnect cable end from coupling. 7. Back out threaded cable fitting from side cover. Ensure that o-ring is removed with cable. Discard o-ring. INSTALL CLUTCH CABLE 1. See Figure 4. Obtain braided stainless steel clutch cable from kit. Apply a light coat of oil on new o-ring and install o-ring (Part Number 11179) onto threaded portion of clutch cable (4). Insert clutch cable fitting (3) into clutch release cover. Do not tighten cable fitting at this time. 2. Connect cable end to coupling. Rotate ramps for best access and install coupling on inner ramp. Place ramp assembly in position in side cover. 3. Install retaining ring. Position retaining ring opening so it is located approximately over the outer ramp tang (the stop that prevents rotation). NOTE Replace clutch release cover gasket if torn or damaged. 4. See Figure 3. Place gasket, if removed, on side cover and install side cover. Tighten the six screws in the order shown to 84-108 in-lbs (10-12 Nm) . 5. Tighten the clutch cable fitting to 36-60 in-lbs (4-7 Nm) . 6. Place a few drops of oil inside cable housing. 7. Route clutch cable as follows: SOFTAIL MODELS FXSTD, FLSTS, FXSTS and FXST – Route clutch cable from the clutch release cover, across the frame, up along the front frame downtubes and across the front of the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. FLSTF and FLSTC – Route clutch cable from the clutch release cover, across the frame and up along the front frame down- tubes, up to and behind the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. DYNA MODELS FXDWG – Route clutch cable from the clutch release cover, under frame and across to the left side. See Figure 5. Insert cable (1) into clip (2) at the bottom left side of the frame

Incoming search terms:

2008 Honda CBR1000RR Clutch Inner Installation PROCEDURE

0

Filed Under (Honda) by admin on 23-04-2011

download
Refer to the 2008 CBR1000RR Service Manual for specific removal instructions. While completing this procedure, be careful not to damage the covers, cowls, or any other components. 1. Remove the air intake cover (page 3-8). 2. Remove the upper inner cover (page 3-9). 3. Remove the lower cowl (page 3-9). 4. Remove the right middle cowl (page 3-10). 5. Remove the right crankcase cover (page 10-5). Clutch Removal (page 10-7) 6. Remove the starter idle gear and shaft. 7. Remove the snap ring and stopper ring. 8. Remove the clutch lifter piece and plate. 9. Unstake the clutch center lock nut. Be careful not to damage the mainshaft threads. 10. Hold the pressure plate with the special tool. You must use the special tool (Clutch Holder, T/N 070MB-MFLA100) when removing the lock nut. Using an impact wrench will damage the main shaft threads. Clutch Holder: 070MB-MFLA100 (autoshipped in May 2008) 11. Remove the clutch center lock nut and washer and discard the lock nut as shown on top of page 3 12. Remove the clutch spring holder, spring seat, and two clutch springs. 13. Remove the spring seat. 14. Remove the following: • Pressure plate
• Spring seat • Judder spring • Clutch disc A • Clutch plate A • Seven clutch discs B • Clutch disc C  Clutch center NOTE: Do not remove the clutch outer. New Clutch Installation (page 10-20) NOTE: The new clutch disc assembly has a dif- ferent order of plates than the illustration shown in the Service Manual. Keep note of this when repairing updated units.
15. Install the new clutch disc assembly with- out removing the setting bolts. Rotate the main shaft to align the clutch disc assem- bly with the main shaft spline. 16. Slightly loosen the setting bolts. 17. Rotate clutch disc C to align its tabs into clutch outer shallow slots, then fully install the clutch disc assembly. 18. Remove and discard the setting bolts. 19. Install the spring seat

Incoming search terms:

HARLEY DAVIDSON DIAMONDBACK "LE" CHROME SERIES CLUTCH CABLE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
CLUTCH CABLE REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery or main fuse following the instructions in the appropriate Service manual. 2. When performing cable disassembly procedures, make careful notes as to the existing cable routing and existing cable strap locations. New straps can be installed in the same locations. 3. Remove the clutch cable following the instructions in the appropriate Service Manual. 4. If installing different handlebars, install them now (refer to the appropriate handlebar instruction sheet) and measure the change in distance that will be required from the end of the cable housing to the clutch lever. Install proper length clutch cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00448b) 5. Compare the additional required length to the cable provided in your kit. If the cable is more than two inches (50.8 mm) longer or more than one inch (25.4 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. CLUTCH CABLE INSTALLATION Sportster and Softail Models Do not over-tighten clutch cable threaded end fitting. Use recommended torque values. Damage to threaded fitting can lead to loss of transmission fluid, which could result in loss of control and death or serious injury. (00449c) -J04568
NOTE Damage to the clutch cable threaded end fitting due to improper handling/installation is not covered under the Harley-Davidson Motor Company Warranty. 1. See Figure 11. Apply a light coat of clean engine oil on the new O-ring (2) before installing the O-ring onto the threaded portion of the clutch cable end. 2. Install the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). 3. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet. FLTR Models with Fairing Lowers 1. See Figure 1. Carefully twist the clutch cable around the coiled opening in the clutch cable guide (2) with the eyelet toward the left handlebar. 2. Route the clutch cable assembly down from the clutch cable clamp while crossing to the right side of the vehicle. Run the cable between the inboard side of the right frame downtube and the outboard side of the voltage regulator. 3. The clutch cable clamp, mounted on the engine guard, has two fingers, an upper and a lower. Feed the cable assembly under one finger and over the other. 4. Finish the installation of the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). NOTE See Figure 2. Adjust the clutch cable clamp to 2.25 ± 0.25 in. (57.15 ± 6.35 mm) as measured from the inside lower left fairing mount to the clutch cable clamp. 5. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet.

Incoming search terms:

HONDA 420 RANCHER 2×4/4×4 2007-2009 CLUTCH KIT INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-12-2011

download
Remove key from the ignition switch. Remove the side panels from both sides. Remove both foot wells. 2. Drain coolant. Remove the oil drain plug from the motor; if you carefully drain it into a clean container you should be able to reuse it. 3. Disconnect shift motor (on electric shift models only). Remove coolant hoses. 4. Remove the bolts that mount the front differential to the frame, no other parts need to be removed. Carefully slide the front differential towards the front of the machine; you might need to lift up slightly to get the differential to move. Remove the drive shaft. Remove o-ring on output shaft (on motor). 5. Remove the fuel pump. 6. Loosen the front crankcase cover bolts, keep track of each bolt length and location. Slowly remove the crankcase cover. Carefully watch for o-ring shims and dowel pins that may fall out. 7. Unstake the nut holding the clutch on and remove nut. Using Honda tool #07933-HB3000A thread the large part of the tool into the center of the clutch. Tighten the center bolt on the tool while holding the large part of the tool with a wrench. This will pull the clutch off the machine. Place the clutch on a clean work surface. EPI performance.com
8. Using the c-clamps push down slightly on the outside cover and remove the four e-clips. Keeping track of which way they come off, remove the round metal plates one at a time. This will allow you to see the complete spring. Remove one end of each spring using a spring tool or needle nose pliers and then remove springs. Install the EPI springs by inserting the spring into the outer edge first. Using a spring tool or pliers (45 degree bent pliers work well) pull on the spring and insert the end into the hole. Install the metal plates and the e-clips. If you can’t get the plates to sit flat make sure each clutch arm is flat against the bottom plate of the clutch. Occasionally when you put the springs on, the clutch arms will pop up. Slide the clutch into the machine. The Sprague clutch is marked “outside” when installing make sure this is facing out. Torque clutch nut to 87 ft/lbs. 9. Clean the gasket surface on the motor and on the cover. Put a thin layer of Honda Bond or Yamabond semi-drying liquid gasket (or something similar as long as it is semi-drying) on the crankcase cover. Carefully install crankcase cover, do not force cover on. Torque bolts to 9 ft/lbs. 10. Install the fuel pump. 11. Install the o-ring on the output shaft (on motor) and install the drive shaft. Carefully slide the front differential back into place and mount to the frame. Install the coolant hoses. Refill your engine coolant to the proper level according to your owner’s manual. 12. Install the oil drain plug. Refill your engine to the proper level according to your owner’s manual. You can reuse your oil if it is clean and was drained into a clean container. Only use manufactures recommended oil. 13. Be sure to double check coolant and oil levels and to look for any leaks after the machine has run for a few minutes. 14. Go out and ride your machine. If your performance doesn’t seem right double check to make sure everything has been done properly. 15. EPI is constantly testing our products. Sometimes there is a need to contact the user with new technical information. To ensure that you are receiving this information visit our web site EPIperformance.com to register your clutch kit.

Incoming search terms:

KAWASAKI CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the key from the ignition switch. Loosen the vent hose on the cover. Remove the clutch cover bolts (10mm socket) and take the clutch cover off. You will need to unplug the wires from the electric actuator and small sensor in the center of the clutch cover to totally remove the cover. To unplug the wires from the sensors, follow the wires to the connections under the plastic side panel and unplug at that location. 2. Remove the primary clutch bolt (19mm socket). This is a left threaded bolt. Insert clutch puller by hand (right hand threads) and tighten until clutch pops off the shaft. This tool is available from EPI, part number PCP-10. Loosen the secondary clutch nut (27mm socket) and remove both clutches at the same time. When you slide the secondary clutch of the machine there are four metal roller pins inside the center shaft of the secondary clutch. These will normally stay in place but if one does fall out refer to assembly instructions in step #6. 3. Disassemble the primary clutch by removing the eight bolts on the cover plate (10mm socket) and remove the spring. Remove one nut (10mm) on the bolt that holds the weight in place, slide the pin out of the clutch and remove the weight. Install EPI weight making sure the tip of the weight is resting on the inside ledge of the clutch. Slide bolt through the holes in the clutch and the weight and install the nut. Repeat this step for the other three weights. NOTE: If your kit has two different gram weights, for example two 54 and two 56 weights, be sure to place them directly across from each other (or every other one). This keeps the clutch in balance . 4. Install the EPI spring and bolt the clutch cover back on using a criss-cross pattern to tighten down the cover. There is a mark on the cover plate and the spider usually in the form of a dot or arrow in the casting. These are alignment marks and must line up when the clutch is assembled. 5. EPI recommends cleaning your clutches when you have them off your machine. Use a clean rag or towel with contact or brake cleaner that does not leave any oily film. Clean all parts of the clutch except for the clutch bushings. Solvent can damage your bushings; just use a dry rag to clean them

Incoming search terms:

DUCATI EVOLUZIONE SLIPPER CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
If installing with Ducati OEM basket you need the washer cod. 0D1SR140C220045 (3mm). – If installing with STM basket (Z12 o Z48) you need the washer cod. 001MG019 (1,5mm). – Insert the correct washer on the gear shaft. – Perform the initial hub group assembly: position the progressive engagement steel plate (003MG015) on the hub (0F3SR140J24001C) , with the step facing up. Be careful to position it correctly into the specific seats, then check that pushing one side, the opposite stand up simultaneously. – Now put the 6 steel balls (001MG025) at the bottom of the grooves using a little bit of grease. Then fix the clutch drum (0F3SR140J24002C) on the clutch hub (0F3SR140J24001C) at rest position, using an M6 screw to help locking the two parts, avoiding in this way any possibility for the steel balls (001MG025) to fall out while inserting the hub pack on the main shaft. – Insert the hub pack on the gear shaft – Insert the clutch discs starting with the sintered one and finishing with the steel guided one; total disc set thickness must be included between 36 and 36,5mm. – Remove the M6 screw from the hub (0F3SR140J24001C). – Put the drum stopper hub (003MG106) on the hub (0F3SR140J24001C). – Verify that the secondary spring support (0F3SR540B140016) is well inserted into its housing on the drum (0F3SR140J24002C). – Insert the secondary spring (0S2085) into its housing on the drum (0F3SR140J24002C). – Mount the pressure plate (003MGP10) on the drum (0F3SR140J24002C) . – Position the Evoluzione spring (0S1090) on the pressure plate (003MGP10), with the convex part facing up (STM logo facing up), making sure previously that the squared section ring (901SE003), which works as primary spring support, is well positioned into the pressure plate itself. – Assemble the complete spring stopper pack: starting from the spring stopper plate (003MG008), with the shaped side facing up as shown in the picture. Insert the ball bearing (003MG007) and finally the spring stopper hub (0F3SR140N220007). Once completed these operations, position the complete spring stopper pack inside the Evoluzione spring (0S1090). – Insert the toothed washer (901RD101) with the convex side facing up, then insert and tighten up the clutch nut (0F30S140C220013); use a dynamometric wrench setting the torque suggested by the bike manufacturer. We suggest to use the specific optional tool (UTL-0020) in order to lock the pressure plate (003MGP10) while performing this operation. – Assemble the complete bearing rest pack: insert the washer (001MG018) in its housing on the bearing rest (0F3SR140N220004). Then put in the same housing the ball bearing and the push rod pin of the original clutch. – Position the complete bearing rest pack in the pressure plate (003MGP10), making sure it fits correctly into the housing grooves. – Manually practise a little pressure on the bearing rest (0F3SR140N220004) in order to release the seat for the tightness circlip (003MG018). – Fit correctly the above mentioned tightness circlip (003MG018). MAKE SURE that it adheres to all the groove perimeter. NB: Once completed the installation, repeatedly operate the clutch lever, checking that the pressure plate performs correctly the opening and closing movements. For a road use of the clutch you have to check clutch plates set every 2000 km. Please verify that the clutch plates set thickness is between 36,5mm and 35,0mm. If it is inferior to 35,0mm please replace a 1,5 steel plate with a 2 mm steel plate. For a racing use of the clutch we suggest to check the clutch plates set thickness frequently. GENERAL SAFETY REGULATIONS – In this sheet are reported the directions to perform correctly the clutch assembly operations. – STM reserves the right – without notice – to introduce any technical change whenever deemed it to be necessary to improve functionality and quality of the products. – Assembly operations must be performed by a skilled technician and must be scrupulously observed. – Before mounting the clutch make a complete inspection of the various parts, in order to verify the possible presence of faults or anomalies on the motorbike. – Make sure that there are no missing/damaged parts in the package . – Some parts of the clutch and its components can have sharp surface: handle with care. – Some components of the clutch, because of their small dimensions can be swallowed: keep away from children. STRADA srl Via Campo Archero 20 10023 Chieri ( TO ) Tel +39 011 9422832 Fax +39 011 9471447 003 MG 018 Tightness circlip

Incoming search terms:

Kawasaki KLR 650 Hydraulic Clutch Installation Manual

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Now, the clutch safety interlock switch. The picture above shows the safety switch contacts. Once you removed the 2 screws holding it to the stock lever, you will need to cut the copper plate on the switch. There are 3 wires: Green, Black with yellow and Blue. You do not use the green wire. You will need to attach the supplied terminals to the remaining wires and slip the supplied rubber boot over them as you attach them to the hydraulic clutch lever. In the photos, the boot is installed and also removed, and with my finger, I am pointing to its location. I did not bother to install the clutch interlock switch and removed the wiring harness completely, but unplugging it from the connector behind the instrument panel. Next, you must remove the clutch cable from the lever in order to pass the cable under the steering head he picture above shows the attachment at the clutch actuator Once the clutch cable is removed from the lever, remove the bolt holding it at on the engine case and disconnect the clutch cable from the pivot. The easiest way to do this is to pull out the clutch pivot assembly and the long “spike” out of the clutch plate hole. (It only goes back in one way, so you can’t mess it up.) he picture above shows that the routing is the same as the original clutch cable. With the hydraulic clutch assembly, pass the stainless steel braided line to the clutch “pivot” point at the engine casing. Attach the clutch cable to the “pivot” while it is removed from the engine, then insert the “spike” into the clutch plates hole (it can only go in one way).

HARLEY DAVIDSON TLE/TLE-ULTRA SIDECAR ATTACHMENT KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
REMOVAL NOTES Refer to the service manual for more information on these generalized steps. Save all removed parts (unless otherwise noted) for installation of this kit or for motorcycle operation without the sidecar. 1. For TLE-Ultra Models: Remove both lower fairings. 2. Remove the bolt and lockwasher securing the right passenger footrest bracket and remove the bracket with footrest. 3. Remove the three right side exhaust heat shields. Some models may require removal of the right side exhaust pipes. 4. Remove stock clutch cable. 5. Remove rear master cylinder/rear brake pedal assembly. Remove rear brake pedal from master cylinder assembly. Remove and save rubber pedal pad and brake pedal. Discard cotter pin. 6. Cut the cable straps holding front oxygen sensor connector to frame bracket. 7. Remove wire harness/brake line clip from right lower frame tube. INSTALLATION New Clutch Cable Installation 1. Refer to the service manual and follow instructions to remove stock clutch cable. 2. Refer to the service manual and follow instructions to connect the new clutch cable to clutch hand lever. 3. For FLHT/C/CU: Follow the instructions in the service manual to route new clutch cable through fairing. 4. For FLHR/C Models: Capture the cable in a clamp at the left upper passing lamp bolt. On FLTR models, capture the cable in a clamp at the left upper bolt securing the speedometer and tachometer housing to the upper fork bracket. These locations are identical with stock cable routing. 5. See Figure 1. Route clutch cable down along left frame downtube (1). 6. Continue to route cable down between left front engine isolator and crankcase. Clutch cable will cross to the right side of motorcycle beneath the crankcase, to the clutch release cover on the right side of the transmission. 7. Install clutch cable fitting into clutch release cover. Refer to the service manual. NOTES The final positioning and attachment of the clutch cable and clutch cable adjustment will be performed after sidecar mounts have been installed. Verify that the clutch cable and the rear brake line do not make contact. Damage could result. 1 2 3 is05785 1. Downtube 2. Clutch cable 3. Route clutch cable behind left front engine iso- lator Figure 1. Route Clutch Cable Relocating Oil Pressure Sending Unit NOTES Perform this procedure on all models equipped with an oil pressure gauge or Police models. All other models proceed to “Master Cylinder Assembly/Rear Brake Pedal Modification.” 1. Remove cable strap securing oil pressure wire harness to frame. 2. Locate the latch on connector to oil pressure sender (next to lower right frame downtube). Raise latch on connector and disconnect connector from oil pressure sender. 3. Remove the oil pressure sender using a 1-1/16 inch open- end crowfoot wrench. 4. See Figure 16. Coat threads of elbow (44) with Loctite 565 and install into crankcase oil pressure sender threads. 5. See Figure 2. Install elbow (1) until snug so open end is in the five-o’clock position (2). Do not over-tighten or crankcase may be damaged. 6. Coat threads of oil pressure sender with Loctite 565 and install into 90 degree brass elbow. Use a 1-1/16 inch open- end crowfoot and tighten to 96-120 in-lbs (11-14 Nm) . 7. Install connector on oil pressure sender unit. Verify that slight clearance to the right engine isolators is present. Adjust position of elbow as required to provide clearance

Incoming search terms:

Cobra Motorcycle Z-Ball Clutch Installation Manual

0

Filed Under (Cobra) by admin on 10-11-2010

download
1. Vehicle preparation a. Shut off the fuel flow to the carburetor at the fuel petcock b. Tilt / rotate the quad over on it’s side so that the clutch cover is up for easy access. 2. Disassemble the old clutch a. Using a 10mm wrench remove the four bolts holding the clutch slave cylinder to the clutch cap. b. You can now remove the entire clutch lever / master cylinder, line and slave from the vehicle, although it would be easier to do at a later time when the vehicle is back resting with four wheels on the ground. c. Using a medium flat blade screwdriver, remove the clutch cap retaining ring and pull off the clutch cap. d. Place the throw out bearing and push rod aside as they will be needed later. e. Using a 4mm hex key, remove the six bolts holding the spring plate and springs. The spring plate will be required for auto clutch installation. f. With a 6mm hex key remove the clutch center bolt, and remove the entire clutch assembly and washers, leaving only the basket in place. The pressure plate (hub) will be required for auto clutch installation. 3. Clutch cover removal to replace thrust washer & eliminate oil shield a. Remove the water pump impeller cover (four socket head cap screws with 4mm hex key). b. Remove the water pump impeller (4mm hex key with piston stop or use an impact driver) c. Remove the kick lever (10mm wrench) d. Remove the clutch cover (5mm hex key)

KAWASAKI TERYX 750 CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove both seats from the vehicle. Next, remove the passenger side lower body panel. There is a mixture of Philips head screws and also plastic push pin fasteners that have to be removed. 2. With the side panel off, the next item to remove is the plastic housing over the engine. These are all “push in” style plastic clips that hold it in place. Once all the pins are out, you can slide the housing off and set it aside. 3. Now the lower long plastic panel under the seat has to be removed (again mainly plastic push clips to remove) . Once they are all out, carefully remove and set aside. 4. Next, remove the fuel tank. Remove the two lines on the top of the tank. There are two straps that hold the tank in place. Remove the bolt from each strap, remove the straps, and lift the fuel tank out. 5. Now the bracket that holds the fuel pump on has to be removed. There are two bolts here to take out. Once this is done, mark the two wires to the coil and disconnect them. Set the bracket out of the way . 6. Next, the clutch cover bolts can be removed and the norkel on the housing can be loosened and i Teryx 750 Clutch Kit Instructions 5/1/09 removed. Take the clutch cove off and set out of the way. 7. With the clutch visible, you can remove the secondary clutch with a large impact wrench and metric socket . 8. Remove the bolt from the primary clutch. This is a left hand thread on the bolt. Next you will need a Kawasaki drive clutch puller (part #352251) to pop the clutch loose. If you do not have a puller, the spring cap can be removed on the vehicle and the weights can be changed out in there as well. 9. With the clutches sitting on the bench, remove the bolts that hold on the spring cover. Remove the stock spring and the stock weights 10. After reading the directions on the new weights, add the correct amount of weight to each clutch weight and install them in the clutch. Place the weight to the left side in the clutch pocket and then install the aluminum spacer. Repeat this process for the other three weights. 11. Install the new spring supplied in the kit and install the spring cover, paying close attention to the arrows on the cover. 12. Next, remove the stock spring from the secondary. It is recommended that you use the TEAM Compression tool (part # 930001) for this. With the clutch on the compression tool, compress the spring retainer down far enough to remove the snap ring with the needle-nose pliers . Slowly back off the t-handle and remove the tool.

Incoming search terms:

Incoming search terms: