honda 500 foreman gas line diagram

You search Auto repair manual PDF honda 500 foreman gas line diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.

HARLEY DAVIDSON XL BRAIDED FRONT BRAKE LINE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
REMOVAL Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1. Drain the brake fluid following the instructions in the service manual. Dispose of waste properly. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Disconnect the battery, negative (-) cable first or remove the main fuse. Follow the instructions in the service manual 3. Remove bolt and two sealing washers to disconnect brake line fitting from master cylinder. Discard sealing washers, but save bolt for installation. 4. Remove bolt and two sealing washers to disconnect brake line fitting from front brake caliper. Discard sealing washers, but save bolt for installation. 5. Carefully make note of brake line routing, then remove existing brake line. NOTE This kit contains clamps and cable straps to either replace the original equipment clamps and cable straps being removed or to add additional brake line support. INSTALLATION Install proper length brake lines. Incorrect brake line length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00325a) Replace brake line gaskets. Re-using original gaskets can cause brake failure and loss of vehicle control, which could result in death or serious injury. (00318a) Avoid leakage. Be sure gaskets, banjo bolt(s) and brake line are clean and undamaged before assembly. (00323a) 1. Position new sealing washers from kit on each side of hydraulic brake fittings (banjo fittings). Small ID washers are for caliper end, large ID washers are for master cylinder end. 2. Insert bolts (removed earlier) through washers and fittings. 3. Hold new braided brake line in position and install bolts into master cylinder and caliper. Tighten only enough to keep banjo fitting in the same orientation as the stock banjo fitting. 4. Verify there is no twist in the brake line. Adjust brake line if necessary. 5. Install clamps from kit by wrapping clamp around braided brake line at each of the clamp mounting locations. Verify clamps are oriented the same as the stock clamps. Install clamp screws but do not tighten. 6. Check entire length of braided brake line: a. Be sure brake line is not twisted. b. Turn handlebars fully-left and right while checking to make sure brake line does not contact any vehicle components. c. Be sure brake line length between clamps is sufficient. 7. Adjust brake line if necessary. 8. Tighten caliper and master cylinder banjo bolts to 20-25 ft-lbs (27-34 Nm) .

2008 Kawasaki ZG1400 Concours ABS Front 3-Line Kit and FK003D625R Single Line Rear INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 29-01-2011

download
Step 1: Identify the key components that complete our front brake line kit: You should have three (3) hoses, one (1) double banjo bolt, and two (2) single banjo bolts There are also a total of nine (9) washers and (3) brass conic inversors. Seven (7) washers and two (2) inversors will be used; the rest are spares. If you have purchased a rear kit as well, locate the following additional pieces: One (1) hose with bracket and c-clip attached, one (1) single banjo bolt, two (2) brass inversors and three (3) washers. You will use one (1) “olive” conic inversor and two (2) washers, the rest are spares. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process can be messy, and brake fluid WILL drip! Step 3: After drying out the OEM brake system, uninstall stock hoses. On the front brake line kit, we are replacing three hoses and their respective blocks (see pictures 1-2 for blocks) . For the rear, we are replacing one hose from the master cylinder to the ABS hard line. Take note of how the stock system was routed, in case you need to reinstall it. Step 4: Locate Line A – This will travel from the master cylinder to the ABS Junction. (See picture 3) You will use a single banjo bolt and two washers at the master cylinder, and an “olive” inversor to thread female end to hard pipe for incoming ABS (right side). * We have replaced the block at the upper triple clamp with a c-clip; please use your stock bolt to thread this in. (See picture 4) Locate Line B – This will travel from the ABS Junction to the right caliper. First, thread the female end to the hard pipe for outgoing ABS (left side). There will be a bolt from the OEM blocks at ABS Junction; please use this to thread c-clips into frame as shown in picture 5 . There is another bolt/OEM block located at the lower triple clamp; please use this to thread the c-clip in as seen in picture 6. Locate Line C – This will cross over the front fender using OEM holders, from right caliper to left caliper. Thread caliper banjos from Line B and C using the following sequence: double banjo hex, washer, 40- degree banjo from Line C, washer, 20-degree banjo from Line B, washer, caliper. Please see pictures 7 and 8 for reference. Thread single banjo bolt into left caliper, using two washers and 40-degree banjo. If applicable, locate rear Line D – this will travel from the rear master cylinder to the hard line for ABS. Thread the hard pipe into female end using a “olive” inversor, and attach bracket to swingarm as seen in picture 9 . Use the bolt from the holder for ABS hose, and sit our bracket on top of the OEM holder. Using the bolt from the OEM ABS hose holder in location shown in picture 10 , attach the c-clip on top of holder and tighten. Finally, thread 30-degree banjo in caliper using the following sequence: single banjo hex, washer, banjo, washer, caliper

Honda Foreman 500 And Honda Rubicon WINCH MOUNTING KIT INSTALLATION

0

Filed Under (Honda) by admin on 13-12-2011

download
Begin by removing the front skid plate located on the front of the ATV. Remove the four side 8mm bolts and four bottom 6mm bolts securing the front skid plate, figure 1. Save the fasteners as they will be used later to reinstall the front skid plate. 2. Remove the four plastic rivets on each side of the front plastic fascia, figure 2. Use a large screw driver to carefully remove the center rivet. After removing the center rivet, remove the rivet housing. Save the fasteners as they will be used to reinstall the front plastic fascia. 3. Remove the two 6mm bolts that attach the front plastic fascia to the bumper, figure 3. Remove the front plastic fascia at this time . Remove the two 6mm bolts that attach the front bumper to the plastic headlight assembly, figure 4. Save the fasteners as they will be used to reinstall the front bumper. 5. Remove the two top 8mm bumper bolts that attach the front bumper to the front rack, figure 5. Save the fasteners as they will be used to reinstall the front bumper. Figure 5 Remove Top Bumper Bolts Remove (both sides) 6. Remove the two ottom bumper bolts that attach the bumper to the bottom of the vehicle frame, figure 6. Save the fasteners as they will be used to reinstall the front bumper

1998-2001 HONDA VFR 800 Complete Brake Line Kit INSTALLATION

0

Filed Under (Honda) by admin on 14-12-2011

download
Identify the key components that complete our brake line kit: You should have nine (9) hoses, one (1) double banjo bolt, fourteen (14) single banjo bolts, (1) single bleeder bolt three (3) drawings, and a picture CD. There are also a total of forty (40) washers and two (2) “olive” conic inversors. Thirty six washers will be used, and two olives. The rest are spares.Step 2: Familiarize yourself with the brake lines, which are labeled for application. Lettered brake hoses A, B, C, D, E, F, G are installed on the front of the motorcycle, while brake hoses (H and I) are installed on the rear. Each label will reference a different drawing, which will show you the location of the key brake system
components.Step 3: To ensure no paint damage from a brake fluid spill, completely cover the bike. This process can be messy, and brake fluid WILL drip! Step 3: Dry out (bleed) your OEM hoses, and take note of how the stock system is installed. You may want to take a couple pictures, in case you need to re-install. Step 4:Remove the stock hoses on the front of the motorcycle, and replace with Galfer hoses labeled A,B,C,D,E,F,G. Locate lines A. this hose will run from the master cylinder down to the right caliper and across the fender through the C-CLIP down to the left caliper. Line D. will run from the (DELAY VALVE) up through the C-CLIP to the right side upper frame female fitting will thread into the male with a (OLIVE) this O.E.M tubing travels to the proportion valve. Line F will run from the left caliper up through the C-CLIP to the left upper frame female fitting and thread to the male with a (OLIVE) this tubing travels to the rear master cylinder. Locate and install line E; this hose will run from the lower delay valve down to the right caliper. locate and install line C& G; line G will travel from the bottom (left) mounting point on the left caliper, to the upper inner mounting point of the left caliper this line joins line C with a double banjo bolt. line C will travel from the inner left caliper through the C-CLIP across the front fender to the inner mounting point of the delay valve

1997-2003 HONDA CBR1100 XX Black Bird Complete Brake Line Kit INSTALLATION

0

Filed Under (Honda) by admin on 05-11-2011

download
identify the key components that complete our brake line kit: You should have eleven (11) hoses, one (1) double banjo bolt, fourteen (14) single banjo bolts, (1) Installation CD. There are also a total of Thirty Six (36) washers and two (2) “olive” conic inversors two (2) c-clips. Thirty Two (32) washers will be used, and two olives. The rest are spares. Step 2: Familiarize yourself with the brake lines, which are labeled for application. Lettered brake hoses A, B, C, D, E, F, G, H, K, I are installed on the front of the motorcycle, while brake hoses (J and K) are installed on the rear. Each label will reference a different drawing, which will show you the location of each brake line. Step 3: To ensure no paint damage from brake fluid, completely cover the bike. This process can be messy, and brake fluid WILL drip! Step 3: Dry out (bleed) your OEM hoses, and take note of how the stock system is installed. You may want to take a
couple pictures, in case you need to re-install. Step 4: Remove the stock hoses on the front of the motorcycle, and replace with Galfer hoses labeled A,B,C,D,E,F,G,H,K,I. Locate lline A. this hose will run from the master cylinder down to the Galfer t-block
joining line B to the right caliper upper mounting point. Line C will travel across the fender down to the left caliper upper mounting point. Line D will run from the (DELAY VALVE) up through the C-CLIP to the right side upper frame O.E.M tubing. The female fitting will thread onto the male with a (OLIVE). This O.E.M tubing travels to the rear master cylinder. Line E Travels from the lower delay valve down to the right caliper lower mounting point. Line F will run from the (SECONDARY MASTER CYLINDER) up through the C-CLIP to the left upper frame O.E.M tubing. The female fitting will thread onto the male with a (OLIVE).This tubing travels tothe rear delay vale