honda fourtrax 300 main jet needle adjustment

You search Auto repair manual PDF honda fourtrax 300 main jet needle adjustment, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda fourtrax 300 main jet needle adjustment Direct Download speed 5282 Kb/s

  honda fourtrax 300 main jet needle adjustment Full Version speed 6162 Kb/s



HONDA ATV Carburetor Repair Kits Installation

0

Filed Under (Honda) by admin on 21-12-2011

download
ATV Carburetor Repair Kits Complete kits to rebuild one OEM carburetor. Each kit contains necessary gaskets/o-rings, needle valve or needle valve set, and jets. Made in Japan. Note: Check all parts before installation. Honda Model Year Order No AT C70 78-85 025-001 AT C90 70-71 025-003 ATC90K1/K2/K3 72-75 025-003 AT C90 76-78 025-003 TRX90 Fourtrax 90 93-98 025-084 ATC110 79-83 025-005 ATC110 84-85 025-061 ATC125M 84-85 025-062 TRX125 Fourtrax 85-86 025-050 TRX125 Fourtrax 87-88 025-063 ATC185 1980 025-009 ATC185S 81-83 025-009 AT C200 81-82 025-008 AT C200 1983 025-009 ATC200E Big Red 82-83 025-064 ATC200ES Big Red 1984 025-064 AT C200M 84-85 025-064 AT C200S 84-86 025-065 AT C200X 83-85 025-012 AT C200X 86-87 025-014 TRX200 Fourtrax 200 90-91 025-066 TRX200D Fourtrax 200 Type II 1991 025-066 TRX200D Fourtrax 200 Type II 92-93 025-067 TRX200D Fourtrax 200 Type II 94-97 025-068 TRX200SX Fourtrax 87-88 025-069 ATC250R 81-82 025-017 ATC250R 83-84 025-018 AT C250R 1985 025-019 ATC250ES Big Red 85-87 025-029 AT C250SX 1985 025-070 TRX250 Fourtrax 250 1985 025-071 TRX250 Fourtrax 250 86-87 025-072 TRX250EX Sportrax 250EX 01-04 025-085 TRX250R Fourtrax 250R 86-87 025-060 TRX250R Fourtrax 250R 1988 025-073 TRX250X 91-92 025-074 TRX300 Fourtrax 300 1988 025-075 TRX300 Fourtrax 300 91-92 025-076 TRX300 Fourtrax 300 93-95 025-078 Honda Model Year Order No TRX300EX Fourtrax 300EX 93-98 025-081 TRX300FW Fourtrax 300 4×4 1988 025-075 TRX300FW Fourtrax 300 4×4 91-92 025-076 TRX300FW Fourtrax 300 4×4 93-95 025-078 AT C350X 1985 025-035 TRX350 Fourtrax 4×4 86-87 025-079 TRX350FE Fourtrax Rancher 4×4 ES 00-03 025-082 TRX350FM Fourtrax Rancher 4×4 00-03 025-082 TRX350TE Fourtrax Rancher ES 00-03 025-082 TRX350TM Fourtrax Rancher 00-03 025-082 TRX350D Fourtrax Foreman 4×4 87-89 025-079 TRX400FW Fourtrax Foreman 95-00 025-080 TRX450ES Fourtrax Foreman ES 98-01 025-083 TRX450FE Fourtrax Foreman ES 02-03 025-083 TRX450FM Fourtrax Foreman S 02-03 025-083 TRX450S Fourtrax Foreman S 98-01 025-083 TRX500FAFourtrax Rubicon 01-04 025-086

Incoming search terms:

KTM 250/ 300/ 380 SX,MXC,EXC ENGINE REPAIR MANUAL

0

Filed Under (KTM) by admin on 12-11-2010

download
Repair manual KTM 250 / 300 / 380 Art No 3206004 -E 2-2C main jet jet needle jet needle air control screw idle adjusting screw idle jet throttle valve Idling range A Operation with closed throttle valve. This range is influenced by the position of the air control screw 1 and the idle adjusting screw 2 . Only make adjustments when the engine is hot. To this end, slightly increase the idling speed of the engine by means of the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Create a round and stable engine speed using the air control screw (basic position of the air control screw = open by 1.5 turns). Then adjust to the normal idling speed by means of the idle adjusting screw. Opening up B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer. Full throttle range D Operation with the throttle fully open (flat out). This range is influenced by the main jet and the jet needle. If the porcelain of the new spark plug is found to have a very bright or white coating or if the engine rings, after a short distance of riding flat out, a larger main jet is required. If the porcelain is dark brown or black with soot the main jet must be replaced by a smaller one. mixture too rich: too much fuel in proportion to air mixture too lean: not enough fuel in proportion to air 1 2 OPERATING RANGES OF THE CARBURETOR 2-3C Carburetor adjustment Basic information on the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95 MOZ). Mixing ratio 2-stroke motor oil : super fuel 1:40 – 1:60. Basic information on a change of the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB:

Incoming search terms:

Yamaha V-Star 1100 Needle/ Jet Kit REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Honda) by admin on 27-12-2011

download
To install this needle and jet kit: • Remove carburetors from the engine per Yamaha shop manual procedures. Note: Always perform internal carburetor work in a clean area. • Remove the vacuum slide from each carburetor. • Remove the OEM needle, spacer and washers, noting order of assembly. (Note; the washers are used as shims to raise the needle, each is equivalent to ½ clip position, use these to fine tune the needle) • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needles. The top is the blunt end of the needle. • Reinstall the OEM spacer and washers as shown in the figure below. • Reinstall the vacuum slides along with the diaphragm spring and reattach the diaphragm covers Note: Verify that the slides maintain their full range of movement! • Drain the fuel from the float bowls and remove the bowl covers. • Remove the OEM main jets and replace them with Baron’s supplied Mikuni main jets. Install the “base setting” main jets as indicated above. NOTE: V-Star 1100 carburetion runs staggered jetting! Make sure the front cylinder’s carburetor gets the larger main jet (numerically), and the rear cylinder’s carburetor gets the smaller main jet . Important! Extra jets have been included in your kit. These will help you fine-tune the carburetors for changing conditions. These conditions include climate and weather patterns in your area as well as exhaust equipment on your motorcycle. Barons determines the jet and clip recommendations that best suit your average riding conditions based upon information supplied to us at the time of your order. Changes in weather, altitude or modifications to your exhaust system may require jets other than those supplied. • Thoroughly clean the inside of the float bowls prior to reinstalling them. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (4)Mikuni main jets #107.5, 110, 112.5, 115, (2) titanium needles, (2) clips, (8) cap-head allen screws Tools required: 3-4-5 mm allen wrenches, 10&12 mm sockets, 10mm end wrench, phillips & flat screwdrivers, pliers, drill. Revision 4.0 • Reassemble the carburetors by reversing the order of above steps. Use the new supplied cap head Allen screws in place of the OEM Phillips head screws for the float bowls. • Locate the fuel mixture screws – they will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plugs

Yamaha Road Star NEEDLE/ JET KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 10-11-2010

download
1. Remove the vacuum slide from the carburetor. 2. Remove the OEM needle, spacer and washers, noting order of assembly. 3. Counting from the top to the bottom, install the new Baron needle clip on groove #4 for 04-07 models and on groove #5 for 99-03 models of the replacement. NOTE: Baron adjustable needle – The top is the blunt end of the needle. 4. Reinstall the OEM spacer and washers as shown in this diagram. 5. Reinstall the vacuum slide along with the diaphragm spring. 6. Reattach the diaphragm cover back and tighten screws. NOTE: Verify that the slide maintains its full range of movement. 7. Drain the fuel from the float bowl and remove the bowl cover. 8. Remove the OEM main jet and replace it with a Barons genuine Mikuni main jet. Install the correct main jet as indicated in JET SELECTION area above on this page. Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or fitment may be required. Page: 2 BA-2420RD NEEDLE/JET KIT – Yamaha Road Star (99-07) 9. Thoroughly clean the inside of the float bowl prior to reinstalling it. 10. Reassemble the carburetor by reversing the order of step #1 through step #10. Use the new cap head allen screws in place of the OEM phillips head screws. 11. Locate the fuel mixture screw – it will either be a screw head or a brass plug. If it is a screw head, skip to step #11c. 11c. If you see a brass plug with a small hole in the center, proceed as follows: With the drill bit, carefully and slowly drill through the fuel mixture plug. CAUTION: The fuel mixture screw is located directly beneath this plug. Be prepared to stop the drill and remove the bit the instant you break through the plug. Insert the self-tapping sheet metal screw into the drilled hole and remove the plug. With air/fuel screw now accessible, use a flat blade screwdriver to turn the screw clockwise until it seats, then carefully turn it counter-clockwise 3 1/2 turns. Refer to step #16 for assistance in fine tuning the setting of the air/fuel adjustment screw. 12. Reinstall the carburetor. We strongly suggest that you attach the throttle cables prior to mounting to intake manifold. 13. Reconnect the fuel line, ensuring the clamp is firmly in place. 14. Reinstall all vent hoses and electrical connectors that were previously removed, checking for any obstructions or blockage. 15. Reinstall the OEM air filter assembly or, if you are installing our Big Air Kit (BAK), follow the instructions that accompany that kit, then continue with next step. NOTES: When the BAK is installed, the vent hose that terminated on the rear of the OEM airbox can be relocated in any safe position that does not kink or pinch it. It is important to verify proper throttle operation before starting the engine.

KTM 60 SX / 65 SX REPAIR MANUAL ENGINE

0

Filed Under (KTM) by admin on 12-11-2010

download
Carburetor adjustment Basic information about the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95). Mixing ratio 2-stroke motor oil : super fuel 1:40 . Basic information of changing the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB: high altitude or high temperatures  choose leaner carburetor adjustment low altitude or low temperatures  choose richer carburetor adjustment * WARNING * -ONLYUSE PREMIUM – GRADE GASOLINE ROZ 95 MIXED WITH HIGH – GRADE TWO – STROKE ENGINE OIL . OTHER TYPES OF GASOLINE CAN CAUSE ENGINE FAILURE , AND USE OF SAME WILL VOID YOUR WARRANTY . -ONLYUSE HIGH – GRADE 2- STROKE ENGINE OIL OF KNOWN BRANDS ( I . E .SHELL ADVANCE RACING X). -NOTENOUGH OIL OR LOW – GRADE OILCAN CAUSE EROSION OF THE PISTON . USING TOO MUCH OIL , THE ENGINE CAN START SMOKING AND FOUL THE SPARKPLUG . -INTHE CASE OFA LEANER ADJUSTMENT OF THE CARBURETOR PROCEED CAUTIOUSLY . ALWAYSREDUCETHEJETSIZEINSTEPSOFONENUMBERTOAVOID OVERHEATING AND PISTON SEIZURE . NOTE: If despite a changed adjustment the engine does not run properly, look for mechanical faults and check the ignition system. Basic information on carburetor wear As a result of engine vibrations, throttle valve, jet needle, and needle jet are subjected to increased wear. This wear may cause carburetor malfunction (e.g., overly rich mixture). Therefore, these parts should be replaced after 1000 hours of using. Idling range – A Operation with closed throttle valve. This range is influenced by the idle adjusting screw 1 . Only make adjustments when the engine is hot. The idling speed can be changed by turning the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Opening up – B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range – C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer

Incoming search terms:

Triumph SU CARBURETORS SERVICING AND TUNING

0

Filed Under (Triumph) by admin on 29-10-2010

download
Jets: These are made in various sizes ranging from.099 inches to.1875 inches, the larger sizes being used only for racing or very high performance engines. The two sizes most commonly found on production cars are the.090 inch and the.100 inch. The size of the jet will be found stamped on the jet head. The figure “nine”wilt indicate that it is the.090 inch and the figure “one”will indicate the.100 inch jet. When tuninga production car the jets size should be checked to make sure that it is of the size recommended by the manufacturers. Centering of Jet: If for any reason, the jet assembly has been removed, it will be ne cessary to recenter the jet. First, remove the clevis pin at the base of the jet which attaches the jet head to the jet operating lever. Withdraw the jet completely and remove the adjusting nut and spring, then replace the adjusting nut, without its spring, and screw it up toits highest position. Slide the Set into position until the jet head is against the base of the adjusting nut. When this has been done, find out if the piston is perfectly free by lifting it up with the finger and allowing it to drop. If the piston is not entirely free, slacken the jet screw and manipulate the lower part of the assembly, including the projecting part of the bottom half of the jet bearing, adjusting nut, and jet head. Make sure that this assembly is now slightly loose. The piston should then rise and fall quite freely as the needle is now able to move the jet into the required central position. The jet screw should now be tightened and a further check made to determine that the piston is still quite free. When complete freedom of the piston is achieved the jet adjusting nut should be removed, together with the jet, and the spring replaced. Experience has shown that a large percentage of carburetors, which have given trouble has been due to the incorrect centering of jets. Jet Needles— These are made in a great variety of sizes, probably now well over two hundred and fifty, and each type of engine hasaneedlethat has been selected, after very careful tests have been carried out, to give the best all-round performance. Most manufacturers actually give three alternative needles for each type and size of engine, these needles clearly being listed by the manufacturer “Standard”, “Rich”or”Weak”and before tuning is started the needle, which is marked on the shank should be checked against the manufacturer’srecommendation to make quite sure that the right needle is fitted; this is most important.

Incoming search terms:

Honda CARBURETOR ADJUSTMENT TOOLS

0

Filed Under (Honda) by admin on 17-12-2011

download
K&L CARBURETOR ADJUSTMENT WRENCHES These tools use tough and accurate bevel gear actuation instead of cable for professional use. The aluminum handle includes index marks for accurate tuning. Sold each. Three types available: 35-9653 Slot-type Pilot Screw Adjustment Wrench for Kawasaki/Suzuki/Yamaha 35-9658 Slot-type Pilot Screw Adjustment Wrench with longer tip for Kawasaki/Suzuki/Yamaha 35-9650 D-type Keihin Pilot Screw Adjustment Wrench for Honda 90-DEGREE 1/4″ HEX DRIVER This gear driven, 1/4″ hex driver set is made of high-grade aluminum and stainless steel. Strongest tool of it’s type on the market. Designed for use on hard-to-reach pilot air screws on inline fours. Can be used with any 1/4″ or 6mm hex bits. 35-7820 90-Degree 1/4″ Hex Driver Set: Includes straight slot, phillips, d-shape pilot screw bit, 6mm hex jet bit & 1/4″ – hex – 1/4″ drive bit. FCR CARB TOOL Set includes three bits – 6mm hex for main jets, long reach straight slot for pilot jets and 3mm allen for float bowl removal. Longer bits make this set ideal for reaching into recessed cavities when adjusting Keihin FCR carburetors. Sold as a set. 35-7978 FCR Carb Tool 12″ DRILL BIT For removal of carburetor plug. (mixture screw plug) 1/8″ bit x 12 inch length. 35-1186 YM-33217-16 JET DRIVER 35-2270 Perfect for removal of jets from small recessed passages

Incoming search terms:

Yamaha V-Star 650 Jet Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 16-01-2012

download
Remove the vacuum slide from the carburetor. • Remove the OEM needle and spacer, noting the order of assembly. • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needle. • Reinstall the OEM spacer and washer. • Reinstall the vacuum slide along with the diaphragm spring. • Reattach the diaphragm cover and tighten its screws. Note: Verify that the slide maintains a full range of movement! • Drain the fuel from float bowl and remove the bowl cover. • Remove the new cap head Allen screws in place of the OEM Phillips head screws. • Repeat above steps for other OEM main jet and pilot jet, and replace them with Baron’s main and pilot jets. • Thoroughly clean the inside of the float bowl prior to reinstalling it. • Reassemble the carburetor by reversing the order of previous steps. Use thecarburetor. • Locate the fuel mixture plug on each carburetor; it will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plug for each carburetor. CAUTION: The fuel mixture screw is located directly beneath this plug. Be prepared to stop the drill and remove the bit the instant you break through the plug. b. Insert a self-tapping sheet metal screw into the drilled hole and remove the plug. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (2) Mikuni main jets, (2) pilot jets, (2) titanium needles, (2) clips, (8) cap head Allen screws Revision 2.0 c. With air/fuel screw now accessible, use a flat blade screwdriver to turn the screw clockwise until it seats, then carefully turn it counter-clockwise 3 turns. Refer to final step for assistance in fine-tuning the setting of the air/fuel adjustment screw. • Reinstall the OEM air filter assembly. • Check all vent lines, fuel lines, and linkage for any obstructions or blockage

HONDA 450E/ S MOUNTING AND ARS ADJUSTMENT INSTALLATION

0

Filed Under (Honda) by admin on 24-12-2011

download
MULTI-RATE SPRINGS AND THE ARS SYSTEM Depending on the application dual–rate springs are fitted on the shocks. Dual-rate springs are just that– a spring set with two separate rates. This is done with a short spring stacked on a longer spring. As both springs collapse they produce a soft, or initial, rate. The spring set will maintain this initial rate until the short spring stops compressing. At that point, the spring rate “crosses over” to the stiffer, or final, rate. This multi-rate system allows a soft initial rate for comfort on small bumps, but has the capability of soaking up the big pot-holes and other off road hazards. ARS stands for Adjustable Rate Suspension. ARS is available on some dual-rate spring 4-wheel ATV shocks. ARS differs from spring preload. The ARS system allows the rider to increase or decrease the load-carrying capacity of the shocks by turning a lever. Depending on the application and spring set, the rider can increase the load capacity of the shocks up to 50 percent. The average preloader that makes a half-inch increase in preload will HONDA 450E/S MOUNTING & ARS ADJUSTMENT INSTRUCTIONS Continued on next page. #TRX450 – 5/28/99 #TRX450 – 5/28/99 Fig. 1. Front shock installation. Note that the shock body is at the top with the shaft pointing down. ARS shown is in the unloaded position. Fig. 2. Rear shock mounting with ARS. Position the lever so that it will not come in contact with any vehicle parts around it. The cup can be rotated to reposition the lever if necessary.
increase the capacity of the shocks to only about 5 to 10 percent. ARS allows the shocks to be correct for solo riding, but still handle the increased weight of an added load. ARS can also be employed to stiffen the rates for aggressive riding. The ARS system consists of an indexing lever and a stepped cup that contains the short spring of the dual- rate. The position of the lever in relation to the steps in the cup determines how long the spring set remains on the soft, or initial, spring rate. On most ARS applications, four positions can be selected from full stiff to full soft. Indexing is done in a matter of seconds by rotating the lever or the cup by hand. Indexing the cup to the lever is usually preferable to avoid interference. Adjustment of the ARS system should only be made while the vehicle is unloaded to reduce the load on the springs. NOTE: It is important to make sure that a step in the cup is positioned directly over the tang on the lever. This will prevent damage to the cup and/or lever that can be caused by making partial contact between the tang and a step. In addition, make sure that the lever will not contact any vehicle parts around it, as the suspension moves up. TUNING TIPS—The “softest” setting on the ARS does not mean that the ride will be the most comfortable at that setting. It means that this is the softest spring setting which would be employed on smooth trails or without a load. Excessive suspension bottoming caused by rough conditions or by the addition of a large load will cause a harsh ride when the shock is adjusted to this setting. To eliminate this bottoming, adjust the ARS to the stiffer positions for a more comfortable ride. Hence, sometimes “stiffer is softer.” NITROGEN PRESSURES IN EMULSION SHOCKS

KYMCO MAXXER 300/ 250 MONGOOSE 300/ 250 SERVICE MANUAL

0

Filed Under (Kymco) by admin on 26-10-2010

download
apply or add designated greases and lubricants to the specified lubrication points. ÑAfter reassembly, check all parts for proper tightening and operation. ÑWhen two persons work together, pay attention to the mutual working safety. ÑDisconnect the battery negative (-) terminal before operation. ÑWhen using a spanner or other tools, make sure not to damage the motorcycle surface. ÑAfter operation, check all connecting points, fasteners, and lines for proper connection and installation. ÑWhen connecting the battery, the positive (+) terminal must be connected first. ÑAfter connection, apply grease to the battery terminals. ÑTerminal caps shall be installed securely. 1 . GENERAL INFORMATION 1-6 ATV 300/250 ÑIf the fuse is burned out, find the cause and repair it. Replace it with a new one according to the specified capacity. ÑAfter operation, terminal caps shall be installed securely. ÑWhen taking out the connector, the lock on the connector shall be released before operation. ÑHold the connector body when connecting or disconnecting it. ÑDo not pull the connector wire. ÑCheck if any connector terminal is bending, protruding or loose. Confirm Capacity 1 . GENERAL INFORMATION 1-7 ATV 300/250 ÑThe connector shall be inserted completely. ÑIf the double connector has a lock, lock it at the correct position. ÑCheck if there is any loose wire

Incoming search terms:

Incoming search terms: