honda gold wing 2005 1800 cooling system

You search Auto repair manual PDF honda gold wing 2005 1800 cooling system, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda gold wing 2005 1800 cooling system Direct Download speed 5282 Kb/s

  honda gold wing 2005 1800 cooling system Full Version speed 6162 Kb/s



2003 SUZUKI SV 650 COOLING AND LUBRICATION SYSTEM SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
COOLING CIRCUIT INSPECTION Before removing the radiator and draining the engine coolant, inspect the cooling circuit for tightness. • * Remove the cowling. (SV650S) (C-7–7-6) • * Loosen the radiator cap stop screw 10 . (SV650) • * Remove the radiator cap O2 and connect the radiator tester to the filler. A WARNING Do not remove the radiator cap when the engine is hot. • * Give a pressure of about 120 kPa (1 .2 kgf/cm2,17.0 psi) and see if the system holds this pressure for 10 seconds . • * If the pressure should fall during this 10-second interval, it means that there is a leaking point in the system . In such a case, inspect the entire system and replace the leaking component or part. A WARNING When removing the radiator cap tester, put a rag on the filler to prevent spouting of engine coolant. CAUTION Do not allow the pressure to exceed specified pressure, or the radiator can be damaged. COOLING AND LUBRICATION SYSTEM 6-3 6-4COOLING AND LUBRICATION SYSTEM RADIATOR REMOVAL • * Remove the cowling. (SV650S) ( r- 7-7-6) • * Drain engine coolant. (r– 72-20) • * Disconnect the right and left radiator hoses from the radiator. • * Disconnect the siphon hose from the radiator. • * Disconnect the horn lead wires. rI .rr • * Remove the radiator lower mounting bolt. • * Disconnect the cooling fan motor and its thermo-switch lead wire coupler 10. • * Remove the radiator by upper mounting bolt. • * Remove the cooling fan. • * Disconnect the cooling fan thermo-switch. • * Remove the cooling fan thermo-switch. • * Remove the horn. CAUTION When removing the horn, hold the nut by spanner to prevent the horn bracket distortion. COOLING AND LUBRICATION SYSTEM 6-5 INSTALLATION • * Install the cooling fan and horn. 0 Cooling fan/horn mounting bolt: 8 N .m (0.8 kgf-m, 6 .0 Ib-ft) • * Install the cooling fan thermo-switch. ( l”76-9) • * Install the siphon hose to the radiator. • * Install the radiator in the reverse order of removal. • * Route the radiator hoses properly. (=9-22) 9-22) • * Install the drain plug with a new sealing washer and pour engine coolant. (=2-20) • * Bleed air from the cooling circuit. (r– 72-21) • * Install the cowling. (SV650S)

Incoming search terms:

Honda GL1500 Gold Wing Motorcycles Trike Conversion Installation Guide

0

Filed Under (Honda) by admin on 19-12-2011

download
Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. • Left and right side-covers (to be re-installed with minor modification). • Seat (to be re-installed without modification). • Trunk. • Left and right passenger foot rests (to be re-installed without modification). • Left and right side-covers above passenger foot rests. • Battery and holder (to be re-installed without modification). • Left and right saddle bags (retain side cover mounting grommets for re-use). • Left and right mufflers. • Rear wheel. • Rear brake line to master cylinder.** • Reverse resistor assembly (to be relocated). • Swing Arm (Drive shaft boot will not be used). • Bank angle sensor. • Shocks. Air shock (non coil-over) to be reused. ** Thoroughly vacuum drain rear brake system, including feed line to left front caliper Modification to Trunk / Luggage Stay Removal from vehicle frame is not necessary. a. Cut the down tubes of the trunk stay and remove the lower section as shown in Figures 1 & 2 b. Trim rear upper tube-end rounded corners just outboard of welded nut. Trim line should be parallel with center line of vehicle. This will provide clearance for body when installed. Figure 2 (Inset) c. Remove the Hazard and Turn Signal relays from the center holder; bend Relay Holder Tab up 90°. Relays will be relocated to left and right sides. Figure 3

HONDA HT1500 GOLD WING CONVERSION KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 25-11-2011

download
Cut-off the saddlebag support tubes where the vertical tube meets the angled tube in the front and back. All you want left is the tour pack support. Loosen tour pack support at bottom bolts, remove top bolts, and then lift up a little. This allows the body to go under the support. If you have the fuel tank: Secure the two black control boxes, facing each other, one on top of the other. Secure to frame using the green ground wire hole at center of frame. Use the 2 ¼”
spacer tube and long screw provided to hold them together. If no fuel tank: leave rear half of fender in place Install machined studs in the swing arm pivot hole with some blue Locktite on them. This provides a 5/8” stud on the side of the frame for the suspension side plates. Screw in until flush with frame. Remove the 6mm bolts from the exhaust heat shield on the outside of the frame rail. nInstall the shock replacement bars on the top shock stud and re-install bolts, leave bars hanging loose for now. Install air-compressor relocation bracket (1 ½” x 4″ w/ 3 holes) and remount compressor. After
mounting, secure the compressor to the bracket with a wire tie.

Honda GL1800 Gold Wing Motorcycles Accent Panel Installation Guide

0

Filed Under (Honda) by admin on 27-10-2010

download
1. Remove left engine side cover. 2. Unplug side stand sensor harness and remove side stand. 3. Cut plug from side stand wiring, leaving approximately 1 ½” of wire on plug. Connect green wires with supplied crimp to bridge side-stand sensor. Figure 1 4. Install modified plug to electrical harness of vehicle. Figure 1 5. Replace engine side cover. 6. Remove center inner fairing panel. 7. Remove lower setting bolts (not to be re-used) from front lower fairing. It is not necessary to completely remove this panel. 8. Lift the side mirror boots and disconnect the running / turn signal wiring. Figure 2 9. With the single plug end first, feed the supplied wire harness into the fairing just below the mirrors. Note: right side wire harness is blue, left is orange. 10. Continue working the supplied harness through the fairing until the single plug end is near the lower part of the lower fairing light nacelles. 11. Connect the supplied wire harness to the vehicles harness at the mirrors and replace mirror boots and center inner fairing panel. Figure 3 12. Remove the center stand and install the supplied cross brace using the OEM bolts and spacer. Install supplied 13 spacers / washers between bracket and OEM spacer as shown. Figure 4

2006 HONDA GOLD WING Specifications

0

Filed Under (Honda) by admin on 29-01-2011

download
Engine Type Liquid-cooled 4-stroke 12-valve SOHC flat-6 Displacement 1,832cm3 Bore x Stroke 74 x 71mm Compression Ratio 9.8 : 1 Max. Power Output 87kW/5,500min-1 (95/1/EC) Max. Torque 167Nm/4,000min-1 (95/1/EC) Idling Speed 700min-1 Oil Capacity 4.6 litres Fuel System Carburation PGM-FI electronic fuel injection with automatic choke Throttle Bore 40mm Aircleaner Viscous, cartridge-type paper filter Fuel Tank Capacity 25 litres (including 4-litre warning light reserve) Electrical System Ignition System Computer-controlled digital transistorised with electronic advance Ignition Timing 2° BTDC (idle) ~ 30° BTDC (3,500min-1) Sparkplug Type BKR6E011 (NGK); K20PR-U11 (ND) Starter Electric Battery Capacity 12V/18AH ACG Output 1,000W Headlights 12V, 55W x 2 (low) / 55W x 2 (high) Drivetrain Clutch Wet, multiplate with coil springs Clutch Operation Hydraulic Transmission Type 5-speed (including overdrive, plus electric reverse) Primary Reduction 1.591 (78/49) Gear Ratios 1 2.375 (38/16) 2 1.454 (32/22) 3 1.068 (31/29) 4 0.843 (27/32) 5 0.686 (24/35) Final Reduction 2.750 (33/12) Final Drive Enclosed shaf

HONDA GOLD WING GL1800 Independent Suspension Owner's Maintenance Notes

0

Filed Under (Honda) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 23-27psig. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm and wheel bearings are sealed and do not require greasing. However, should you experience unusual wheel bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Rear end lubrication . Your differential comes filled with SAE 85W140 API GL-6 gear oil. You should not have to top-off the differential unless you experience axle seal or pinion seal leaks. If you want to check the oil level, do so by removing the fill plug on the top of the differential housing (Remove seat) and by using a suitable measuring device, the oil level should be 5 1/4″ inch down from the top of the differential housing. Refill as necessary. Change the differential oil every 30,000 – 35,000 miles by draining it and refill with 2 quarts of above gear oil.. 5. Brakes . Check your front and rear brake system fluid levels every 3,000 miles and top-off as necessary. Inspect brake pads every 10,000 miles and replace as necessary. Rear brake pads are Volkswagen Part # D101P. 6. Drive Train . The rear driveshaft U-joint and slip yoke spline are fitted with grease fittings, pump the fittings with wheel-bearing, graphite or high-pressure grease every 3,000 to 5,000 miles. The front u-joint does not have grease fittings. 7. Suspension System : The suspension is a Double A-arm Independent suspension with a standard single setting anti-roll bar or an optional Variable Sway Control (VSC) which can be adjustment for optimal ride, handling characteristics and performance. The A- arms are equiped with bushings that does not require servicing. The suspension system is designed to give you the best ride with a load of no more than 600 pounds (passengers plus cargo plus trailer tongue weight): 8. EZ-Steer (rake kit) : If your trike is equipped with Champion’s EZ-Steer, the bearings are a wear item. You should follow your motorcycle manufacturer’s recommended front-end triple-tree maintenance requirements. Generally these call for an initial service at 1,000 miles followed by periodic maintenance at 10,000 mile intervals

HONDA GOLD WING GL1500 AND GL1800 TRIKE CONVERSION KIT Owner's Maintenance Notes

0

Filed Under (Honda) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 20-25 psi. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm and wheel bearings are sealed and do not require greasing. However, should you experience unusual wheel bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Rear end lubrication . Your differential comes filled with 1 quart of SAE 85W140 API GL-6 gear oil. You should not have to top-off the differential unless you experience axle seal or pinion seal leaks. Check the oil level every 10,000 miles, or sooner if you experience leaks, and refill as necessary. Do not fill higher than the fill-hole. Change the differential oil every 30,000 – 35,000 miles. 5. Brakes . Check your front and rear brake system fluid levels every 3,000 miles and top-off as necessary. Inspect brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . If your driveshaft U-joint and/or splines are fitted with grease fittings, pump the fittings with wheel-bearing, graphite or high-pressure grease every 3000 to 5,000 miles. If yours does not have grease fittings then lubrication is not required. 7. Suspension System : The suspension system is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight): GL1500: The OEM adjustable air shock is used in conjunction with two (2) new Progressive 416 air shocks. The three shocks should be pressurized to about 20 psig, but to no more than 70 psig; GL1800: You can still use your OEM mono-shock pre-load adjustment. Your two (2) new coil-over shocks do not have an air system connection. However, there is a pre-load adjuster ring on each new shock that is factory-set at the “lowest” setting, for the softest ride. Changing this setting will result in a stiffer ride. 8. EZ-Steer (rake kit) : If your trike is equipped with Champion’s EZ-Steer, the bearings are a wear item. You should follow your motorcycle manufacturer’s recommended front-end triple-tree maintenance requirements. Generally these call for an initial service at 1,000 miles followed by periodic maintenance at 10,000 mile intervals. 9. Electrical : Your trike is pre-wired for a trailer connection. The harness is just below the trunk door on the underside of the body.

Incoming search terms:

Honda GL1500 Gold Wing Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 17-02-2011

download
REMOVAL OF ORIGINAL PARTS Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. • Left and right side-covers (to be re-installed with minor modification). • Seat (to be re-installed without modification). • Trunk. • Left and right passenger foot rests (to be re-installed without modification). • Left and right side-covers above passenger foot rests. • Battery and holder (to be re-installed without modification). • Left and right saddle bags (retain side cover mounting grommets for re-use). • Left and right mufflers. • Rear wheel. • Rear brake line to master cylinder.** • Reverse resistor assembly (to be relocated). • Swing Arm (Drive shaft boot will not be used). • Bank angle sensor. • Shocks. Air shock (non coil-over) to be reused. ** Thoroughly vacuum drain rear brake system, including feed line to left front caliper PREINSTALLATION PREPARATION 3.1 Modification to Trunk / Luggage Stay Removal from vehicle frame is not necessary. a. Cut the down tubes of the trunk stay and remove the lower section as shown in Figures 1 & 2 b. Trim rear upper tube-end rounded corners just outboard of welded nut. Trim line should be parallel with center line of vehicle. This will provide clearance for body when installed. Figure 2 (Inset) c. Remove the Hazard and Turn Signal relays from the center holder; bend Relay Holder Tab up 90°. Relays will be relocated to left and right sides. Figure 3 d. Disconnect and remove Bank Angle Sensor from its mount tab (Bank Angle Sensor will not be re-used). Cut wires midway between sensor and plug. e. On plug end, splice / connect red and green wires together to close the circuit. f. Cut and remove the Bank Angle Sensor mount tab from the Trunk stay. Figure 4 3.2 Modification to Rear Inner Fender Removal of fender and attached parts is not necessary for modification. a. Place supplied template (See last page) on fender (left and right sides) as shown and mark outline. With box cutter, cut fender along template outline. Once material is removed, make a vertical cut up the side (line indicated by arrow Figure 5) of the fender. Do not continue cut across top of fender. Figure 5 b. Carefully heat underside of fender with heat gun and bend fender upward until aft end contacts frame cross member. c. Drill holes in plastic fender through cross brace at locations indicated and secure fender to cross with zip ties. Figure 6

Honda VTX 1800 Motorcycles EZ-Steer Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Honda VTX 1800 EZ-Steer Instruction Installation of the Champion EZ-Steer system is similar to the installation of the OEM triple clamps of your Honda VTX 1800 Motorcycle. We strongly recommend that you use your OEM service manual and follow the prescribed disassembly, installation and torque specifications (except where noted below) for the upper and lower clamp assembly. Recommended Procedures • Disconnect all wiring to headlight and remove headlight, windscreen (if so equipped) and brackets from motorcycle. • Remove handle bars from top clamp. • Remove brake caliper and brackets; disconnect all mounting points on brake lines. Secure calipers to frame being careful not to damage brake lines. • The wheel and fork tube assembly can be removed as one complete unit. • Remove steering lock fromOEM bottom clamp and install on Champion’s bottom clamp. • Replacing the upper OEM bearing and race with the Champion supplied bearing and race, install Champion’s lower triple clamp to motorcycle reusing original hardware as removed. Torque bearing lock nut to 35 lb. ft.. • Install covers to bottom forks if supplied with OEM motorcycle. • Install Champion upper clamp with OEM washer and dome nut. Leave loose. • Slide forks up and into the upper clamp until top of forks are flush with top surface of clamp. • Torque dome nut to 75 lb. ft.. • Ensure that fork tube extensions are flush with top of upper clamp. Torque lower 8mm bolts to 20 lb.ft. and upper 10 mm clamp bolts to 30 lb. ft.. • Install handle bars to upper clamp using OEM nut and flat washers. • Reinstall brake line holders to the lower triple clamp. • Reinstall all other OEM parts as removed. • Bleed brakes. • OEM windshield # 08R80-MCH-100 can be used on this kit

Incoming search terms:

2005 Honda CRF450R OWNER'S MANUAL AND COMPETITION HANDBOOK

0

Filed Under (Honda) by admin on 02-12-2010

download
Normal Engine Stop 1. Shift the transmission into neutral. 2. Turn the fuel valve OFF. 3. Lightly open the throttle (1) 2 – 3 times, and then close it. 4. Depress and hold the engine stop button (2) until the engine stops completely. Failure to close the fuel valve may cause the carburetor to overflow, result in hard starting. Emergency Engine Stop To stop the engine in an emergency, press the engine stop button. Basic Operating Instructions 15 Help assure your CRF’s future reliability and performance by paying extra attention to how you ride during the first operating day or 15 miles (25 km). During this period, avoid full-throttle starts and rapid acceleration. This same procedure should be followed each time when: •piston is replaced •piston rings are replaced •cylinder is replaced •crankshaft or crank bearings are replaced Break-in Guidelines 16 Basic Operating Instructions Servicing Your Honda 17 Servicing Your Honda Keeping your CRF well maintained is absolutely essential to your safety. It’s also a good way to protect your investment, get maximum performance, avoid breakdowns, and have more fun. To help keep your CRF in good shape, this section includes a Maintenance Schedule for required servicing and step-by-step instructions for specific maintenance tasks. You’ll also find important safety precautions, information on oils, and tips for keeping your Honda looking good. An ICM (Ignition Control Module) system is used on this motorcycle; consequently, routine ignition timing adjustment is unnecessary. If you want to check the ignition timing, refer to the Honda Service Manual (page 156).

Incoming search terms:

Incoming search terms: