honda mufflers baffles

You search Auto repair manual PDF honda mufflers baffles, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda mufflers baffles Direct Download speed 5282 Kb/s

  honda mufflers baffles Full Version speed 6162 Kb/s



HARLEY DAVIDSON DYNA STREET PERFORMANCE SLIP-ON ACCESSORY MUFFLERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
PRODUCT INFORMATION Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. Noise Emission Warranty Harley-Davidson warrants that these mufflers, at the time of sale, meets all applicable United States E.P.A. Federal noise and Emissions standards. This warranty extends to the first person who buys these mufflers for purposes other than resale, and to all subsequent buyers. Warranty claims should be directed to an authorized Harley-Davidson Dealer. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances. INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 2. Loosen stock muffler clamps and remove nuts that attach mufflers to muffler support tube. Remove stock mufflers. Save all mounting hardware for reinstallation. 3. Install new kit mufflers using muffler clamps (purchased separately) and stock mounting hardware saved from Step 2. Do not tighten hardware at this time. NOTE Before tightening nuts that attach mufflers to muffler support tubes, make sure the front muffler is positioned as far forward in its brackets slot as possible. This will eliminate any possible contact between the mufflers. 4. Tighten muffler clamp bolts to 45-60 ft-lbs (61-81 Nm) . Tighten nuts that attach mufflers to muffler support tube snugly. 5. Connect the negative (-) battery cable

HARLEY DAVIDSON SOFTAIL MUFFLER SLIP-FIT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
1. Disconnect negative battery cable. Perform this installation when the engine is cool. Installing these mufflers when the engine is hot could cause burns which could result in moderate to minor injury. 2. Remove mufflers according to applicable Service Manual instructions. Shotgun exhaust mufflers will come off the vehicle as a pair, attached together. Staggered dual mufflers will come off the vehicle attached to the interconnect tube. 3. For a shotgun exhaust, skip to Step 6. 1 CAUTION 1 WARNING 1 WARNING 1 of 2 4. Remove mufflers from interconnect tube and discard gaskets and mufflers. 5. Install mufflers to interconnect pipe using new gaskets (6) and existing screws. Slip muffler clamps (1) on mufflers and install assembly back on vehicle. Tighten screws to 96-120 in-lbs (10.8-13.6 N-m). Tighten muffler clamps to 45-60 ft-lbs (61-81.3 Nm). Attach the interconnect tube to the frame using the existing flange lock nuts and washers. Tighten to 30-33 ft-lbs (40.7- 44.7 Nm). 6. On shotgun style assemblies, assemble top and bottom mufflers using interconnect seal. Torque screws to 96-120 in-lbs (61-81.3 Nm). Attach interconnect tube to frame using existing flange locknuts and washers. Torque to 30-33 ft-lbs, (40-7-44.7 Nm). 7. Replace fasteners and tighten as follows: muffler clamps to 45-60 ft-lbs (61-81.3 Nm), flange locknut on carriage bolt to 30-33 ft-lbs (40.7-44.7 Nm) and tighten screws and washers to 15-19 ft-lbs (20.3-25.8 Nm). 8. Reconnect negative battery cable. Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. Noise Emission Warranty Gabilan Manufacturing, Inc. warrants that these mufflers, at the time of sale, meet all applicable United States E.P.A. Federal noise standards. This warranty extends to the first person who buys these mufflers for purposes other than resale, and to all subsequent buyers. Warranty claims should be directed to an authorized Harley-Davidson Dealer. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances.

HARLEY DAVIDSON DYNA SLIP-ON ACCESSORY MUFFLERS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 2. Loosen stock muffler clamps and remove nuts that attach mufflers to muffler support tube. Remove stock mufflers. Save all mounting hardware for reinstallation. -J04263 3. Install new kit mufflers using muffler clamps (purchased separately) and stock mounting hardware saved from Step 2. Do not tighten hardware at this time. NOTE Before tightening nuts that attach mufflers to muffler support tubes, make sure the front muffler is positioned as far forward in its brackets slot as possible. This will eliminate any possible contact between the mufflers. 4. Tighten muffler clamp bolts to 45-60 ft-lbs (61-81 Nm) . Tighten nuts that attach mufflers to muffler support tube snugly. 5. Connect the negative (-) battery cable

Honda Motorcycle Na vigation Kit

0

Filed Under (Honda) by admin on 28-11-2010

download
Honda Motorcycle Na vigation Kit Honda Motorcycle Navigation Kit G e n e r i c A c c e s s o r i e s 2 0 0 8 For your peace of mind Honda Genuine Accessories are carefully designed, researched and stringently test ed tot he highest standards. And since they’re all Honda approved you’llknowthat they’rejustastoughand well made as your Honda motorcycle. Please Note -All prices quoted are correct at time of printing and are subject to change without prior notice. y e a r w a r r a n t y GENUINE ACCESSORIES Honda Motorcycle Navigation Kit Model Part Number Description RRP Remarks NAKED CBF 600 08A 40MER800B CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY CBF 600 08A 40MER800A CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY ON/OFF XL700V 08A 40MFF800 * CONTAINS NA VI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EARPH ONE, MANUAL, 08A 30MFF800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY XL 1000V 08A 40MBT800 CONTAINSNAVI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EAR PH ONE, MANUAL, 08A 30MBT800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY TOURERS/SPORT TOUR ERS DN-01 08A 40MEH800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, AND BATTERY -CONTAINS 08A 30MEW800 ADDITIONALSTE ERIN G HANDLE C LAMPS FORV ISU AL INTE GRAT ION OF THE COMPONENT NT700V 08A 40MEW800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, BATTERY

Incoming search terms:

Fitting new GL1500 Mufflers Installation Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
The stock mufflers on the GL1500 Goldwing tend to rust after a few years. It doesn’t really matter how much you clean them because the design means that they tend to collect condensation which turns into water, then the dreaded tinworm rots them from the inside out. There is a drain hole in each muffler (near the front) to allow some water out, but the hole is really in the wrong place as the mufflers almost always rot at the ends near where the tailpipe is welded on. Replacing mufflers on the GL1500 Goldwing is easy enough and you really don’t need a tutorial for the task. But I did have a camera handy on the day I did the job so you may as well have the benefit of the images. This is a common sight on a GL1500 Goldwing. The mufflers rot from the inside out and eventually the ends just blow off. Believe it or not, these mufflers are on a 1997 GL1500SE with only 7,700 miles that was always stored in a dry garage! I replaced them in April 2004 and they had been almost as bad as this since 2002, but the owner of the Goldwing wasn’t using it much so he didn’t bother replacing them until 2004

HONDA SHADOW ACE TOURER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the pinch clamp bolt on the left hand muffler crossover pipe. (Located on the right of the motorcycle, where both mufflers merge with the head pipes). 2. Remove the two 8mm bolts that mount the left hand muffler to the frame. Drop the muffler down to clear the mounts and pull out from the collector. 3. Remove the right hand frame cover to avoid damaging it. 4. Remove the 8mm nut holding the head pipe flanges to the cylinder heads. Remove the 8mm bolts that mount the right hand muffler to the frame. 5. Remove the remainder of the exhaust system from the motorcycle and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Be sure to check that the stock exhaust gaskets are in good shape. If you have any doubts as to their condition, replace them. 2. Install the chrome exhaust flanges (supplied) over the front and rear head pipes. 3. Install the rear head pipe to the rear cylinder using the stock 8mm acorn nuts. Route the pipe approximately 3/4″ beneath the swingarm, leaving the nuts finger tight at this time. 4. Install the front head pipe to the cylinder head using the stock 8mm acorn nuts. Its routing follows the stock head pipe, leave the nuts finger tight at this time. 5. Your Vance & Hines mufflers use the stock mounting locations and rubber grommets. Remove the steel spacers and rubber grommets from your stock mufflers and install them into Vance & Hines mufflers in the same locations. 6. Slip a chrome muffler clamp onto the inlet end of each muffler. Install the clamp hardware as shown in figure 1 (hardware supplied). Leave them loose at this time. 7 Slide the left hand muffler assembly (stamped H641) onto the rear head pipe approximately two inches. Mount the mufflers to the motorcycle using the stock bolts, in the stock locations. 8. Repeat the above step with the right hand muffler (stamped H640). 9. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edges of the heat shields with the location of the mounting clips that are welded to the back side of the heat shield. Position the right rear heat shield (stamped H226) over the rear head pipe and feed the tail end of the hose clamps into the clips. Be sure that each clamp is engaged into both clips. Repeat this procedure with each heat shield.

Honda Goldwing GL1800 Solid Rear Axle Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Specifications Overall Width: 57.75″ Overall Length: 108″ Overall Length w/EZ-Steer 109.5 Wheel Base: 71″ Extended 4.5″ At Rear Axel Wheel Base w/EZ Steer 72.5″ Load Capacity: 500 Lb Tire Size: 205 / 70 / R15 Wheel Size (15″) Offset +35 mm 15x7JJ 4×4.5 Tire Pressure 20 PSI Suspension: “Zero-Flex” Internal Swing Arm utilizing 3 shocks, OEM shock absorber plus 2 coil over shock absorbers. Rear Differential: Champion Lightweight rear axle / differential assembly. Gear Ratio 2.93:1 gear ratio Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 6.75 cubic feet. 3 full-face helmets and additional storage. Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 7 of 28 Revision 10 4 Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. • Seat (to be re-installed without modification) • Left and right side covers (to be re-installed without modification) • Battery and battery box (to be re-installed without modification) • Left and right saddle bags • Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) • Trunk (to be re-installed without modification) • Left and right passenger foot rests (to be re-installed without modification) • Left and right foot rest under covers (to be modified and re-installed) • Left and right rear crash bars • Saddle bag trunk stay (to be modified and re-installed) • Left and right mufflers (Mufflers only, do not remove decorative covers) • Rear wheel • Left and right pivot bolt covers (to be re-installed without modification) • Reverse resistor (to be relocated) • Swing Arm – Note : Carry out brake system modifications (Section 5) prior to removing Swing Arm. • Note : Upper bolt of mono shock can be removed without removing the fuel tank. • Note : Do not remove actuator hose from actuator pump or shock absorber. Dismounting shock actuator pump will allow more movement of shock absorber when removing swing arm.Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 8 of 28 Revision 10 5 Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm. From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Sidecars Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Sidecars Trike Conversion Kit.

Incoming search terms:

1997 Honda CBR 1000 F specifications review

0

Filed Under (Honda) by admin on 20-12-2011

download
Front brakes: Dual disc Rear brakes: Single disc Speed and acceleration Top speed: 255.0 km/h (158.4 mph) Power/weight ratio: 0.5745 HP/kg Other specifications Further information Parts and accessories Check out parts and accessories from our partners. Ask questions Join the 97 Honda CBR 1000 F discussion group Insurance, loans, tests Search the web for dealers, loan and insurance costs, tests, customizing, etc. Related bikes List related bikes for comparison of specs Buying a bike starts at Bikez Get a list of related motorbikes before you buy this Honda. Inspect technical data. Look at photos. Read the riders’ comments at the bike’s discussion group. And check out the bike’s reliability, repair costs, etc. Show any 1997 Honda CBR 1000 F for sale on our Bikez.biz Motorcycle Classifieds. You can also sign up for e-mail notification when such bikes are advertised in the future. And advertise your old MC for sale. Our efficient ads are free. You are also welcome to read and submit motorcycle reviews. Rating sample for this Honda bike Value for money for the 1997 Honda CBR 1000 F: (67.1 out of 100) Click here for complete rating. You can also compare bikes.

Incoming search terms:

Honda Foreman 500 And Honda Rubicon WINCH MOUNTING KIT INSTALLATION

0

Filed Under (Honda) by admin on 13-12-2011

download
Begin by removing the front skid plate located on the front of the ATV. Remove the four side 8mm bolts and four bottom 6mm bolts securing the front skid plate, figure 1. Save the fasteners as they will be used later to reinstall the front skid plate. 2. Remove the four plastic rivets on each side of the front plastic fascia, figure 2. Use a large screw driver to carefully remove the center rivet. After removing the center rivet, remove the rivet housing. Save the fasteners as they will be used to reinstall the front plastic fascia. 3. Remove the two 6mm bolts that attach the front plastic fascia to the bumper, figure 3. Remove the front plastic fascia at this time . Remove the two 6mm bolts that attach the front bumper to the plastic headlight assembly, figure 4. Save the fasteners as they will be used to reinstall the front bumper. 5. Remove the two top 8mm bumper bolts that attach the front bumper to the front rack, figure 5. Save the fasteners as they will be used to reinstall the front bumper. Figure 5 Remove Top Bumper Bolts Remove (both sides) 6. Remove the two ottom bumper bolts that attach the bumper to the bottom of the vehicle frame, figure 6. Save the fasteners as they will be used to reinstall the front bumper

Incoming search terms:

HONDA VTX1800R AND HONDA VTX1800N BIG SHOTS EXHAUST SYSTEM REMOVAL

0

Filed Under (Honda) by admin on 17-11-2011

download
If motorcycle is oxygen sensor equipped, unscrew the sensors from the stock exhaust system and install them
into the Vance & Hines exhaust system, being sure to install the front cylinder sensor into the lower pipe and
the rear cylinder sensor into the top pipe. Note: Use caution when handling. Do not touch sensor tip area.
2. If motorcycle is not oxygen sensor equipped, install both M12 x 11 plugs and washers (supplied)into the oxygen
sensor bosses. 3. Check condition of stock exhaust gaskets. Replace if damaged or worn. 4. Install and tighten supplied mounting bracket (stamped 345-P) in the original mounting bar location, using one M10 x 35 flange bolt and nut on top (supplied) and one M10 x 20 flange bolt on bottom (supplied) (Figure 2). Note: The bracket mounts behind the top frame mount and in front of the bottom frame mount(Figure 2).5. Install and tighten rectifier using M6x30 flange bolt, nut
and washer combinations (supplied) (Figure 2). 6. Place heat shields on a non-abrasive surface such as a blanket or carpet. Using a felt tip marker mark outside surface of front and rear heat shields with location of the mounting clips welded to the inside

Incoming search terms: