honda pcx 125 led lights

You search Auto repair manual PDF honda pcx 125 led lights, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda pcx 125 led lights Direct Download speed 5282 Kb/s

  honda pcx 125 led lights Full Version speed 6162 Kb/s



Motorcycle LED lights RENEGADE LIGHTS Installation Guide

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Make sure your bike is cool and parked on a flat secure surface! 2. Find your battery (you may have to remove your seat or side covers in order to get to your battery) Disconnect the NEGATIVE ( -) cable. Negative battery cable must be disconnected from the battery in order to avoid safety hazards! Be sure as you disconnect the Negative cable that it does not touch or make contact with your Positive terminal 3. Your new motorcycle LED lights are polarity sensitive–meaning that the RED wires on the LEDs must be hooked to the Positive (+) terminal and the BLACK wires must be hooked to the Ground (-) . All Red Wires must go to a common power wire and ALL Black Wires must go to a common ground. You cannot run the LED motorcycle lights in a series nor can you run the wires from one motorcycle LED light to another in a loop type installation. ( All of the wires on the motorcycle LED lights which you install will end up together in one place at your battery.) 4. Pick a hidden flat surface around the front of your seat area to mount the switch. ( You must be able to reach the switch when the seat and/or side covers are back on your bike.) You will install your switch later using the double-sided tape provided to you. 5. Next, begin choosing the locations where you would like to mount your motorcycle LED lights. Choose areas which will give you the most light coverage overall, but which will allow the motorcycle LED lights itself to be hidden from easy view when you are standing back and looking at the bike. 6. Clean each area where you choose to place a motorcycle LED light with the alcohol based cleaner making sure all dirt and/or oil is removed from that area

Incoming search terms:

Motorcycle LED lights RENEGADE LIGHTS Disconnection Guide

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Make sure your bike is cool and parked on a flat secure surface! 2. Find your battery (you may have to remove your seat or side covers in order to get to your battery) Disconnect the NEGATIVE ( -) cable. Negative battery cable must be disconnected from the battery in order to avoid safety hazards! Be sure as you disconnect the Negative cable that it does not touch or make contact with your Positive terminal 3. Disconnect the fuse holder from the battery – both the positive ( +) and negative ( -) sides. 4. Cut the wire to the light that is not working with the side cutters. 5. At the problem light twist the light case back and forth slowly and then pull firmly, DO NOT yank to remove from the motorcycle. 6. If the motorcycle led light does not come off easily, repeat the twisting motion back and froth until you feel the light loosen – then pull. 7. Pull the motorcycle led light away from the motorcycle slowly until the cut end of wire falls free. 8. If you will NOT be using your motorcycle until the new lights arrive, you may stop at this step. SAFETY POINT: Otherwise, where you cut the wire, you need to dead end or tape the cut wire. This will keep it from shorting out until the new motorcycle led light is installed. 9. Reconnect fuse holder to battery. 10. Reconnect the battery and then install the seat. 11. Return the motorcycle led light or lights to Renegade Lights along with Warranty Return Policy Form. 12. Renegade Lights will return your new motorcycle led lights along with instructions for installing them.

Incoming search terms:

Introducing the New BMW R 1200 RT-P

0

Filed Under (BMW) by admin on 15-12-2010

download
The new R 1200 RT-P features a completely new LED emergency lighting concept developed by BMW and Code 3 PSE. The new system combines all currently desired emergency lighting into optimally focused compact LED light modules. These modules accommodate an additional 45 degree front LED module that blankets the front quadrants in emergency light. Together with an integrated wiring harness and programmable flash control module, the new system can provide any current flashing sequence / switching combination through settings on the programmable flasher. Example: If the motor will be used in California, program the flasher for steady-burn left front LED light, with no change in the LED light or the wiring. If the motor is sold or operated in a different venue later, change the program flasher for 49 state operation. The rear light module combines rear and side facing LED emergency lights, together with rear-facing brake/tail LED and side turn signal LED lights. Additional rear facing LED emergency lights can be installed and powered in conjunction with the rear facing lights, or controlled by photo- eye to disable the lights during the dark to reduce glare at night / low light situations. The programmable flasher can provide 12 flash patterns, with wiring splitting the motor between left and right side for alternating flash patterns. Light sequencing begins with rear, programmable rear and front side lights, as well as front and 45 degree front lights. A rear cancel switch allows riders to disable the rear lights while retaining the side and front lights – usually used for protective service details. The programmable flasher also provides for a primary and secondary flash pattern, so during code 3 operation, the emergency lights will display the primary pattern until the siren is activated, at which time the flasher changes to the alternative pattern for 7 seconds after each siren tone change. This feature known as InterClear provides a visual and audible alert to those nearby

Incoming search terms:

LED SHOW LIGHTING INSTALLATION INSTRUCTIOINS

0

Filed Under (Tips and Review) by admin on 27-12-2010

download
1. The kit is supplied with 4 “cluster” lights that project a round flood lighting pattern and 4 “array” lights that have a narrow fan type pattern. Determine where you would like to mount the supplied lights, switch and wiring connections. You may want to hook up one of the lights with some long jumper wires connected to the battery and hold it in various places to see what will show off your bike best. The idea is to see the light reflected off your bike and not see the light fixture. 2. Mount the lights and switch using the supplied primer and 2-sided adhesive pad. Apply the primer to the backside of the lights and switch; let it dry for 5 minutes. Remove the protector from one side of the adhesive pad and apply. Apply the primer on the motorcycle where the lights and switch will be mounted and let it dry for 5 minutes. Remove the protector from the adhesive pad and mount the lights and switch. 3. Refer to the provided wiring diagram. The wiring is color-coded and connects in parallel. All of the black wires connect together through the BLACK wire of the 2 conductor black jacketed wire (Ground Wires). All of the colored wires connect together through the RED wire of the 2 conductor black jacketed wire (Power Wires). Connections may be soldered, crimped with solderless connectors, or twisted together. 4. Measure and cut the supplied 2-conductor black-jacketed wire to the lengths that are needed to connect the lights and switch. When routing the wire from any lights that you have mounted to the front make sure you have provided enough slack at the steering head to be able to turn the front wheel full left and full right without damaging the lights or wires. Also be sure the wire is at least æ” from any exhaust pipe. 5. Join each connection and cover with the supplied heat shrink tubing. NOTE; All wire connections must be insulated. Cut a piece of the provided heat shrink tubing long enough to cover the connection completely. 6. Connect one wire from the switch to the RED wire of the lights with one of the supplied blue butt connectors. Connect the second wire from the switch to one wire from the fuse holder with the other blue butt connector. Connect the second wire from the fuse holder to the positive (+) battery terminal using one of the supplied fork connectors. 7. Connect the BLACK wire of the lights using the other fork connector to a ground connection. (The negative (-) battery terminal or motorcycle frame.) 8. Secure all loose wires by using the supplied cable ties. Check the front wheel again to be sure there is enough wire slack for turning.

Incoming search terms:

BMW R1200GS Dual Function LED Running Lights and Flashing Brake Lights installation instructions

0

Filed Under (BMW) by admin on 08-11-2010

download
The flasher is set to flash continuously as long as the brake is applied. To convert to a 5 second flash and then stay solid while the brake is applied, cut the green wire loop on the flasher. Use electrical tape to protect and secure the green wires to the other wires. 2. Remove the rider’s seat. Locate the wire bundle that starts at the rear of the motorcycle. At the most accessible spot carefully remove 3″ to 3½” of protective wire loom. I know, I know…it’s really beautifully done. Cowboy up! Take it off! 3. Mount the flasher in a location that will not crimp wires or interfere with the other bike assemblies. Locate the +12 volt wire ( GRAY wire with BLACK stripe and YELLOW banding) from the brake light Attach the kit RED wire to the brake light positive wire using one of the Posi-Tap connectors in the kit. 4. Locate the Ground wire ( BROWN wire) from the brake light. Attach the kit BLACK wire to the motorcycle ground wire using a Posi-Tap connector. 5. If you have a Fuse Block with ignition switched relay installed, route the Hyper-Lite GRAY wire to a fused circuit on the (relay activated) fuse block . 6. If you do not have a Fuse Block installed, find the alarm circuit connector under the seat . The alarm circuit has a rectangular connector and five wires, White with Black stripe; White with Brown stripe; Red with White; Brown with White; and Green with White stripe. Use a Posi-Tap to attach the Hyper-Lite GRAY wire to the green wire with white stripe. Pull the wire loom back from the wire. Tap into the wire with the Posi-Tap provided. . 7. If using the Hyper-Lite License Plate Mounting bracket, install it now. OR: Clean the side facing reflectors at the rear of the bike with alcohol. Mount the LED modules vertically on the reflectors so that the LEDs point straight back. Press in place for about 5 seconds. The tape can be used only once! If you goof, new tape is required. 8. Route the BLUE and BROWN wires from the flasher and the LED modules. Trim the Blue and Brown wires to remove any excess wire . Use a Posi-Twist to connect the 3 BLUE wires together. Use a Posi-Twist to connect the 3 BROWN wires together. (see Posi-Twist Connector instructions)

Incoming search terms:

CUSTOM LED 2004-2006 YAMAHA ROAD STAR INTEGRATED TAIL KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 10-11-2010

download
1 ) REMOVE THE SCREWS ON THE BACK SIDE OF THE TAIL LIGHT THAT HOLD THE CHROME TRIM TO THE TAIL LIGHT. 2 ) POSITION YOUR CUTTING WHEEL AS SHOWN IN THE PICTURE TO THE LEFT WHERE THE CLEAR PART OF THE LENS TURNS 90 DEGREES. THE CUTTING WHEEL SHALL REMAIN IN THE PLANE OF THE LENS. 3 ) PROCEED TO CUT INTO THE CLEAR LENS APPROXIMATELY HALF OF THE THICKNESS, ALL THE WAY AROUND THE PERIMETER OF THE LENS – BE SURE NOT TO CUT ALL THE WAY THROUGH BECAUSE IT WILL NOT GLUE BACK TOGETHER PROPERLY. SEE “TIPS FOR CUTTING YOUR LENS” BEFORE BEGINNING. TIPS FOR CUTTING YOUR LENS A) KEEP THE CUTTING WHEEL MOVING AND APPLY LIGHT PRESSURE. SITTING IN ONE SPOT WILL JUST MELT THE PLASTIC. WHEN YOU MAKE YOUR WAY AROUND THE ENTIRE PERIMETER, CLEAN ALL THE BURRED PLASTIC FROM AROUND THE EDGES AND FROM INSIDE THE GROOVE YOU’VE MADE. OPENING THE LENS 4 ) PLACE THE TIP OF A FLAT HEAD SCREWDRIVER IN THE GROOVE YOU HAVE CREATED. 5 ) GENTLY TWIST THE SCREWDRIVER TO CRACK THE GLUE ALONG THE GROOVE. NOTE: AS SOON AS YOU HEAR THE SOUND OF THE GLUE GIVING (A CRACK), MOVE THE SCREWDRIVER SLIGHTLY AND ADVANCE THE CRACK. SLOW AND STEADY IS THE NAME OF THE GAME HERE. IF YOU FIND A HARD SPOT, WEAKEN IT WITH THE CUTTING WHEEL AS NECESSARY. THE HARD PART IS OVER! YOU CAN RELAX NOW! 2 ©2005 Custom LED LLC. All Rights Reserved. 6 ) REMOVE THE SCREWS HOLDING THE STOCK LED BOARDS TO THE HOUSING (YOU WILL BE REUSING SOME OF THE SCREWS SO PUT THEM TO THE SIDE). 7 ) REMOVE THE STOCK LED ASSEMBLY FROM THE LENS HOUSING. YOU WILL NO LONGER NEED THE STOCK LED BOARD, DISPOSE OF IT AS YOU WISH. 8 ) GENTLY PRY OFF THE PLASTIC COVER TO EXPOSE THE DRIVER BOARD UNDERNEATH. 9 ) REMOVE THE SCREWS SUPPORTING THE DRIVER BOARD AND SNIP OFF THE THREE WIRES (BLUE, BLACK, YELLOW) AS SHOWN AS CLOSE TO THE CIRCUIT BOARD AS POSSIBLE! YOU WILL NEED TO CONNECT TO THESE WIRES LATER. 10 ) POP OUT THE LITTLE BLACK PLUG AS SHOWN IN THE PICTURE. YOU CAN POKE IT OUT FROM THE INSIDE OF THE HOUSING. WIRING UP YOUR CUSTOM LED BOARD PLACE YOUR CUSTOM LED INTEGRATED TAIL BOARD NEXT TO THE HOUSING AND MATCH THE WIRE COLORS AS FOLLOWS: TRY TO HANDLE THE CIRCUIT BOARD AS LITTLE AS POSSIBLE AS FINGERPRINTS AND DIRT WILL HINDER THE PERFORMANCE. • BLACK ON HARNESS TO 6″ BLACK ON CUSTOM LED BOARD • BLUE ON HARNESS TO 6″ BLUE ON CUSTOM LED BOARD • YELLOW ON HARNESS TO 6″ YELLOW ON CUSTOM LED BOARD USE THE THREE (3 OF 5) SUPPLIED ORANGE SPLICE CONNECTORS. PUSH THE TWO WIRES TO BE SPLICED TOGETHER INTO THE OPEN END. BE SURE TO PUSH THE WIRES ALL THE WAY IN (UNTIL YOU CAN SEE THEY HAVE REACHED THE OTHER SIDE). NOTE: YOU WILL NEED TO SEPARATE THE THREE WIRES FIRST BY CUTTING THE PLASTIC COLLAR THAT BINDS THEM. FOR THE WIRES TO FIT PROPERLY INTO THE CONNECTORS, YOU MUST ALSO REMOVE THE REMNANTS OF THE COLLAR FROM THE WIRES. NOTE: THE SPLICE IS MORE RELIABLE IF THE WIRE IS NOT STRIPPED. BE SURE TO SNIP OFF THE BARE ENDS OF THE WIRES ON THE CUSTOM LED TAIL TO ENSURE THAT THERE IS INSULATION WHERE THE SPLICE WILL OCCUR. THE SUPPLIED SPLICE CONNECTORS AUTOMATICALLY DISPLACE THE INSULATION AS NECESSARY. ONCE YOU DOUBLE CHECK YOUR COLOR MATCHING AND ARE ABSOLUTELY SURE THAT THE WIRES ARE FULLY INSERTED INTO THE SPLICE CONNECTORS DO THE FOLLOWING: 11 ) SQUEEZE THE SPLICE CONNECTORS FIRMLY WITH PLIERS. VISUALLY INSPECT YOUR CONNECTIONS TO SEE THAT THEY HAVE BEEN SPLICED PROPERLY INSIDE. 12 ) RUN THE GREEN AND BROWN WIRES THROUGH THE HOLE YOU OPENED UP IN STEP 9

Incoming search terms:

motorcycle Turn Signal Conversion Kit Installation Instructions

0

Filed Under (Tips and Review) by admin on 09-11-2010

download
1. Place motorcycle on solid, level ground and on center stand if equipped. 2. Remove your turn signal lens. Place it upside down and clean the lens interior with the supplied alcohol wipe. Allow to completely air dry. Note: the LEDs are mounted to the inside of the turn signal lens with the LEDs making direct contact with the lens. The supplied silicone is used to secure the LED board to the lens. It remains flexible but can be removed. Test fit the board in your lens prior to using silicone. 3. Using a small screwdriver, poke a small hole in the end of the tube of silicone. Place a dab of silicone on each of the 12 LEDs on the circuit board. CAUTION : Note the position of the metal pins on the back of the LED board, They must be located 90 degrees from where the holes are that secure the lens to the housing. See attached diagram. 4. Position the round circuit board over the inside of your turn signal lens with the LEDs facing down. Get the board as centered as possible. Allow the silicone to make contact with the inside of the lens and then push down and slightly rotate the board back and forth to allow the LEDs to make contact with the lens surface. Repeat other side. NOTE : the silicone will require 30 minutes in 70 degree weather to tack up. Full cure will occur within 24 hours. We suggest not riding for several hours if possible to allow the best adhesion. 5. You will need to access the following wires; running light (license plate can be used), brake lights, right turn and left turn. Disassemble the bike as needed to gain access to the wiring. Shop Tip: we have found that on the Yamaha Star Series and the Kawasaki Cruisers that installation is much easier when you remove the turn signal bar from the fender. On the Yamahas, there are 3 bolts holding the moustache in position. The wires will unplug from behind the license plate. On the Kawasakis, unplug the signals under the seat and bend the tabs under the fender to be able to remove the wires. 6. We have provided some tubing to slide over the wires so that when you re-install the bulb socket, our wires for the LED boards will not be pinched. This tube should be slid all the way into the turn signal housing. You may have to shorten the tubing for your installation. 7. You will need to run wires through the stem of the turn signal. You can see samples of how the various manufacturers signal housings come apart on our web site. Click on “Other Lighting Products” and then “Turn Signal Conversion Kits” and follow the link. We suggest placing the removed turn signal assembly on a towel on your work area. 7. You will need to leave 2″ of slack in the wires at the turn signal housing to allow for wire connection. 8. Reinstall the turn signal housing back on the motorcycle if removed. NOTE: both of the run/brake circuits must be used. You may shorten the wires only on the run/brake circuits as needed. Do not change the circuits under the heat shrink. T-Tap instructions. Lay the “donor” wire in the slot in the burgandy connector. Close and snap together with pliars. Strip some insulation off of the wire which will be tapping into the factory wire. Crimp one of the pink connectors on the bare wire and plug it into the burgandy T-Tap 9. Connect the green wires from the run/brake circuits to the bikes running lights. The 2 greens can be connected together. 10. Connect the blue wires from the run/brake circuits to the bikes brake lights. The 2 blues can be connected together. 11. Take one of the red wires from a run/brake circuit and connect it to one of the black with white stripe wires coming from one of the LED boards using the supplied red butt connector. Connect the other run/brake circuit red wire to the remaining black with white stripe wire on the other LED board. 12. Connect the black wire from the LED board on the right side of the bike to the right turn signal positive (+) wire on the motorcycle. 13. Connect the black wire from the LED board on the left side of the bike to the left turn signal positive (+) wire on the motorcycle. 14. Plug the wires into the LED boards. If you hold the turn signal lens so that you are viewing the back of the LED board, position the connectors on the board at the 12 o’clock (top) position. The connector on the left is the positive (+) terminal. Connect the red wire to it. Connect the black wire to the remaining connector on the right side. 15. Check operation. LEDs should come on with running lights. LEDs will brighten when brake lights are applied. LEDs will shut off when the amber turn signal comes on. 16. Should you have any problems, please see the troubleshooting chart on our website.* * 17. Reassemble bike

Incoming search terms:

Harley Davidson Installing The Ride Time Ultra Progressive Tour Pak LED Tail Lights

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Remove the light bulbs from the tail light housing by depressing the tab on the bulb socket assembly and turning counter clockwise. Remove the bulb from the bulb socket. 2. Remove the lenses from the warp-around light fixture. These lens are held in place by a non-hardening black sealant. In addition, there are three plastic alignment tabs on the lens body that clip into the lens frame. To remove the lens, insert the supplied push Stick through the hole in the back of the light bulb housing and gently but firmly push the lens outward. This action places a stress on the alignment tabs. 3 . Using a flat blade screw driver, pry the lens away from the frame at the top, side, and bottom to release the lens alignment tabs. Go back to step 2, and use the plastic tube to push the lens outward. It may be necessary to repeat the prying process and pushing process several times to remove the lens. Note: Some users have found it useful to heat the lens area with a hair dryer to soften the adhesive. Included in this kit are: Left and Right LED modules, 1 RTQC Quick Connect Accessory Cable , 2 RTV application sticks, 1 push stick, Approximately 3 inches of shrink tube, and 1 copy of instructions. Required for installation, but not included are: A tube of Permatex RTV (available at Wal-Mart), 1/8 inch drill bit, a drill, small flat blade screwdriver, other hand tools. Window/ body sealer if required to reseat lenses can be obtained at your local glass shop. Tour Pak, Harley Davidson, Electraglide, Raod King, and Ultraglide are registered trade marks of Harley David- son. Harley Davidson does not make or endorse the use of these lights. 4. When the lens begins to emerge from the frame, grasp it at the top and bottom and pull the lens from the housing using a up and down motion. Set the lens aside . Avoid having the sealant contact other surfaces. In most cases, the lens can be reinstalled without adding additional sealant . Note: Do not use RTV to reset the lens. If sealant is needed obtain a non-hardening body/windshield sealant from your local glass shop. 6. When you are comfortable with the location of the circuit board, drill a 1/8 inch hole in the back of the light housing. This hole will be used to bring the turn signal wire from the LED module into the Tour Pak. 7. Using the supplied stick, spread a thin layer of Permatex clear RTV silicone seal along the area where the circuit board will be located. Apply a similar layer to the top of the light housing. Route the turn signal wire through the 1/8″ hole and position the circuit board in the housing. Allow the RTV to cure. 5. Test fit the LED light board in the light housing.

Incoming search terms:

Harley Davidson Steering Wheel Radio Control Interface Installation instructions

0

Filed Under (Harley Davidson) by admin on 03-05-2012

download
1) Turn on the ignition to supply power to the SWI-3. 2) Use a pen to depress the “program mode” button. Remove pen when left LED light comes on. 3) Within 10 seconds press and hold one of the steering wheel function buttons. Continue to hold steering wheel button until the left LED turns off. Release the steering wheel button and the right LED turns on. 4) Place the stereo’s IR remote within 3″ of the “IR Input” port on the side of the SWI-3 next to the program button. Press and hold the remote’s button that corresponds to the steering wheel button that was pressed. Continue to hold the remote’s button until the right LED turns off. Release the button and the left LED will turn on. 5) Repeat steps 3 and 4 until all radio steering wheel functions are programmed. 6) When programming is complete, wait 10 seconds and both LED’s will flash 3 times. This indicates an automatic program exit. Do not stop more than 10 seconds while programming or there will be an automatic program exit and you will have to start over at step number 2 above. Turning off ignition before the automatic exit will require starting over at step 2 above. The SWI-3 can be reprogrammed unlimited times. Testing • Test the SWI-3 by holding it’s infrared LED (LED on the end of 4′ lead) close to the stereo and verify that it works properly. Experiment with various locations for the LED. You should be able to find a hidden and convenient mounting location. Try along the top front and /or bottom of the stereo as well as it’s sides. The LED can be replaced with most any IR LED, like Radio Shack’s # 276-143. The longest lead of the LED connects to the red wire of the 4′ cable and the short lead of the LED connects to the black wire of the 4′ cable

Incoming search terms:

Motorcycle Security System INSTALLATION MANUAL

0

Filed Under (Tips and Review) by admin on 04-04-2012

download
The transceiver is pre-charged at the factory and will operate out of the box but we recommend that it be charge for at least 10 hours when first operated to insure full life of battery. 1. Plug in provided charger into the transceiver. 2. While the transceiver is charging the red status LED will flash twice every two seconds. 3. When transceiver is fully charged no LED will flash. 4. Recharge the transceiver every day to maintain full function. Receiver Status LED Panel The status LED panel provides information about the status of the receiver, memory and the battery level. Receiver on / Memory Trigger Blue LED will flash Receiver on / Low Battery Red LED will flash. Receiver On White LED will flash Range LED Range LED indicates when the transceiver is still with in receiving range of the system. In Range Green LED will flash Out Of range Red LED will flash Operating the transceiver The following instruction assumes that the transceiver is with in range of the motorcycle. Arming Press the #1 button, the siren will chirp 3 times. The transceiver will chirp twice and the white status LED will continuously flash to confirm that the receiver is on. The range LED light will then flash green . System is armed.

Incoming search terms: