honda recon idle mixture

You search Auto repair manual PDF honda recon idle mixture, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda recon idle mixture Direct Download speed 5282 Kb/s

  honda recon idle mixture Full Version speed 6162 Kb/s



Ural carburetors Installation and idle adjustment

0

Filed Under (Ural) by admin on 02-11-2010

download
1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ¼ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

Incoming search terms:

HONDA CR250R Owner’s Manual

0

Filed Under (Honda) by admin on 24-04-2011

download
l. CONTROLS( 1 ) Frontbralte tever (2) Throttle grip ( 3 ) Engine stop switch When shutting off engine, press in the  engine stop switch button. (4 ) Rear brake pedal ( 5 I Kickstarter pedal ( 6 } Clutch lever (1′) Fuel tank filler cap ( 8) Gear change pedal The transmission has S speeds. Depress the pedal to Shift into [st gear. Raise the pedal to shift into 2nd, 3rd, 4th and 5th. Neutral is located between 1st and 2nd.  9 ) Fuel mixture enrichment l-mob When starting a cold engne, raise the fuel mixture knob and fully depress the kickstarter pedal. (10) Fuel valve When the fuel valve is turned to "OFF", fuel cannot Flow from the fuel tank to the carburetor. When the fuel valve is turned to “ON”, fuel will flow from the tank to the carburetor. (1 1] Rear shock absorber adjuster The rear shock absorber springs have three settings for precise adjustment of the rear suspension to suit riding conditions and differences in rider weight. Page 6 2 l. OPERATING – Fig. l—2 (1) Fuel tank -  2. FUEL The Honda CRZSUR ELSINORE has a two-stroke engine that requires a gasoline-oil mixture. The capacity of the “fuel tank is 8.59 (2.2 US gal. 1.9 Imp. gal). I Any automotive gasoline with :1 pump octane number of 86 or higher. or research octane number of9i or higher‘ may he used. If “l ofgasoline or a higher octane grade. USE HONDA 2-STROKE INJECTOR OIL OR EQUIVALENT. I Premix gasoline and oil in a ratio of   20:1 Prepare the fuel mixture in a clean container, and shake until thoroughly mixed before Flling the fuel tank. i Too much oil will muse excessive smoking and spark plug fouling. Too little oil will cause engine damage or premature wear. Mix fuel in a ratio of 20 parts gasoline to 1 part oil. I Vegetable oils separate from gasoline more easily than mineral oils, especially in cold weather. It is advisable to use mineral oil when ambient temperatures of below 0°C (32°F) are expected. I If the gasoline-oil mixture is left standing in a container for a long period of time, lubricity will deteriorate. Use the mixture within 24 hours. I Once an oil container is opened, the oil must be used within one month, since oxidation may occur. Do not mix vegetable and mineral oils. Gasoline is flammable and explosive under certain conditions. Always stop the engine and do not smoke or allow open flames or sparks near the motorcycle when refueling

Incoming search terms:

Honda Motorcycle Na vigation Kit

0

Filed Under (Honda) by admin on 28-11-2010

download
Honda Motorcycle Na vigation Kit Honda Motorcycle Navigation Kit G e n e r i c A c c e s s o r i e s 2 0 0 8 For your peace of mind Honda Genuine Accessories are carefully designed, researched and stringently test ed tot he highest standards. And since they’re all Honda approved you’llknowthat they’rejustastoughand well made as your Honda motorcycle. Please Note -All prices quoted are correct at time of printing and are subject to change without prior notice. y e a r w a r r a n t y GENUINE ACCESSORIES Honda Motorcycle Navigation Kit Model Part Number Description RRP Remarks NAKED CBF 600 08A 40MER800B CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY CBF 600 08A 40MER800A CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY ON/OFF XL700V 08A 40MFF800 * CONTAINS NA VI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EARPH ONE, MANUAL, 08A 30MFF800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY XL 1000V 08A 40MBT800 CONTAINSNAVI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EAR PH ONE, MANUAL, 08A 30MBT800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY TOURERS/SPORT TOUR ERS DN-01 08A 40MEH800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, AND BATTERY -CONTAINS 08A 30MEW800 ADDITIONALSTE ERIN G HANDLE C LAMPS FORV ISU AL INTE GRAT ION OF THE COMPONENT NT700V 08A 40MEW800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, BATTERY

Incoming search terms:

MIKUNI VM CARBURETOR SUPER TUNING

0

Filed Under (Mikuni) by admin on 31-10-2010

download
This manual is intended as a guide for users of Mikuni carburetors who want to learn the adjusting method to the best performance from our products. In motorcycles, special tuning of the engine is now considereda routine practice. The arrows that appear in the drawings in this text show the direction in which air, fuel and an air-fuel mixture flows, respectively. ¢JAir Fuel “Mixture Mounting angle fore and aft inclination of the carb should not exceed approx Function of a carburetor The function of a carburetor is to produce combustible air-fuel mixture, by breaking fuel into tiny particles (in the form of vapor) and by mixing the fuel with air in a proper ratio, and to deliver the mixture to the engine. A proper ratio (mixture ratio or air-fuel ratio) means an ideal air-fuel mixture that can burn without leaving an excess of fuel or air, Whether the proper mixture ratio is maintained or not holds the key to the efficient engine operation, 2. Air-fuel mixture required by the engine (Fig. 1) The ratio of a mixture of fuel and air is called the mixture ratio or the air-fuel ratio and is generally expressed by the weight proportion. Theoretically, the amount of air required for complete combustion of 1 gram of fuel under normal conditions is

Incoming search terms:

Adjusting the Pekar K68 for Dnepr or Ural

0

Filed Under (Tips and Review) by admin on 11-11-2010

download
1. Make sure the ignition timing is correct 2. Adjust the valves as necessary to ensure proper operation 3. Run the engine to warm it up a bit 4. Adjust the float setting. To do this, remove the carburetors (leave the throttle cables attached), remove the bowl and turn the carburetor upside down (fuel will spill). The float should look like this: Adjust as necessary by bending the float support (#37 in Figure 1). Reinstall Installation and idle adjustment 1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns. * Starting using the K68′s (cold weather) 1. Verify fuel flow. Apply choke (pull 52 in Fig1). 2. Using the ticklers (13) allow fuel to enter the bowl until fuel drains from (14) 3. With the ignition off, kick 1 or 2 times 4. Turn ignition on, and as soon as engine is warmed up (maybe sooner) push choke mechanisms to open choke Idle Adjustment (engine running and warm) 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ¼ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

Incoming search terms:

HONDA GL1500CD/ VALKYRIE Specifications

0

Filed Under (Honda) by admin on 29-01-2011

download
position when it comes to the environment. We continue to develop low-emission technologies for our current and future motorcycles, ATVs, scooters and personal watercraft. We already produce models that exceed the stringent 2008 CARB emissions requirements years ahead of schedule. And that’s the kind of performance everybody can appreciate. BE A RESPONSIBLE RIDER. Riding a motorcycle is an exercise in responsibility—to yourself, to others, to the environment and to the sport. So remember, wear a helmet, eye protection and protective clothing whenever you ride. Never ride under the influence of drugs or alcohol, and never use the street as a racetrack. Inspect your motorcycle before riding, read your owner’s manual, and see your local Honda Dealer concerning reimbursement through the Honda Rider’s Club of America™for Motorcycle Safety Foundation (MSF) rider training.* Always obey local laws, use common sense, and respect the rights of others when you ride. Make sure you have a proper license when riding on public roads, and never modify your motorcycle’s exhaust system. 03 SPECIFICATIONS ACCESSORIES VALKYRIE Log on to our website at honda.com for more information about Honda Genuine Accessories . On a bike like the Valkyrie, you can never have too much chrome. And that’s precisely why we offer our Chrome Sidecovers and Chrome Swingarm-Pivot cover to help really brighten up these areas. Here’s one of our most popular Valkyrie accessory options. These Leather Saddlebags look great, hold plenty, and match some of the other leather accessories we have available. Got a long trip planned, or is winter right around the corner? Then make sure you take a look at-or should we say take a look through-a Honda Genuine Accessories Windshield for your new Valkyrie. GL1500CD 1520cc liquid-cooled horizontally opposed six-cylinder with belt-driven overhead camshafts Six 28mm constant-velocity carburetors 71.0 x 64.0mm Solid-state digital Five-speed constant-mesh Shaft 150/80R-17 radial 180/70R-16 radial Dual-disc with twin-piston calipers 28.9 inches 66.5 inches 5.3 gallons, including 1.1 gallon reserve 681 pounds Black Windshield, leather saddlebags, chrome exhaust tips, chrome rear carrier, CB transceiver kit, passenger CB talk switch, studded backrest pad, studded main seat, studded rear seat, deluxe backrest pad

Incoming search terms:

HONDA VTX1800R & HONDA VTX1800N BIG SHOTS EXHAUST SYSTEM

0

Filed Under (Honda) by admin on 10-11-2011

download
harness. Remove wire tie (take note of harness routing for reassembly). Un-route wires and drape over right side of pipe. 3. Remove entire right side floorboard assembly, (three bolts) (Figure 1). 4. Remove exhaust port flange nuts.
5. Remove flange bolts securing rear muffler mount to exhaust system mounting bar. 6. Remove complete exhaust system. Start by removing front head pipe from exhaust port (assistance may be required). 7. Remove rectifier from mounting bar. 8. Remove stock (cast iron) exhaust system mounting bar.

HONDA VTX1800R AND HONDA VTX1800N BIG SHOTS EXHAUST SYSTEM REMOVAL

0

Filed Under (Honda) by admin on 17-11-2011

download
If motorcycle is oxygen sensor equipped, unscrew the sensors from the stock exhaust system and install them
into the Vance & Hines exhaust system, being sure to install the front cylinder sensor into the lower pipe and
the rear cylinder sensor into the top pipe. Note: Use caution when handling. Do not touch sensor tip area.
2. If motorcycle is not oxygen sensor equipped, install both M12 x 11 plugs and washers (supplied)into the oxygen
sensor bosses. 3. Check condition of stock exhaust gaskets. Replace if damaged or worn. 4. Install and tighten supplied mounting bracket (stamped 345-P) in the original mounting bar location, using one M10 x 35 flange bolt and nut on top (supplied) and one M10 x 20 flange bolt on bottom (supplied) (Figure 2). Note: The bracket mounts behind the top frame mount and in front of the bottom frame mount(Figure 2).5. Install and tighten rectifier using M6x30 flange bolt, nut
and washer combinations (supplied) (Figure 2). 6. Place heat shields on a non-abrasive surface such as a blanket or carpet. Using a felt tip marker mark outside surface of front and rear heat shields with location of the mounting clips welded to the inside

Incoming search terms:

Honda Foreman 500 And Honda Rubicon WINCH MOUNTING KIT INSTALLATION

0

Filed Under (Honda) by admin on 13-12-2011

download
Begin by removing the front skid plate located on the front of the ATV. Remove the four side 8mm bolts and four bottom 6mm bolts securing the front skid plate, figure 1. Save the fasteners as they will be used later to reinstall the front skid plate. 2. Remove the four plastic rivets on each side of the front plastic fascia, figure 2. Use a large screw driver to carefully remove the center rivet. After removing the center rivet, remove the rivet housing. Save the fasteners as they will be used to reinstall the front plastic fascia. 3. Remove the two 6mm bolts that attach the front plastic fascia to the bumper, figure 3. Remove the front plastic fascia at this time . Remove the two 6mm bolts that attach the front bumper to the plastic headlight assembly, figure 4. Save the fasteners as they will be used to reinstall the front bumper. 5. Remove the two top 8mm bumper bolts that attach the front bumper to the front rack, figure 5. Save the fasteners as they will be used to reinstall the front bumper. Figure 5 Remove Top Bumper Bolts Remove (both sides) 6. Remove the two ottom bumper bolts that attach the bumper to the bottom of the vehicle frame, figure 6. Save the fasteners as they will be used to reinstall the front bumper

Incoming search terms:

1997 Honda CBR 1000 F specifications review

0

Filed Under (Honda) by admin on 20-12-2011

download
Front brakes: Dual disc Rear brakes: Single disc Speed and acceleration Top speed: 255.0 km/h (158.4 mph) Power/weight ratio: 0.5745 HP/kg Other specifications Further information Parts and accessories Check out parts and accessories from our partners. Ask questions Join the 97 Honda CBR 1000 F discussion group Insurance, loans, tests Search the web for dealers, loan and insurance costs, tests, customizing, etc. Related bikes List related bikes for comparison of specs Buying a bike starts at Bikez Get a list of related motorbikes before you buy this Honda. Inspect technical data. Look at photos. Read the riders’ comments at the bike’s discussion group. And check out the bike’s reliability, repair costs, etc. Show any 1997 Honda CBR 1000 F for sale on our Bikez.biz Motorcycle Classifieds. You can also sign up for e-mail notification when such bikes are advertised in the future. And advertise your old MC for sale. Our efficient ads are free. You are also welcome to read and submit motorcycle reviews. Rating sample for this Honda bike Value for money for the 1997 Honda CBR 1000 F: (67.1 out of 100) Click here for complete rating. You can also compare bikes.

Incoming search terms:

Incoming search terms: