honda shadow 2005 750areo starter relay and wiring harness

You search Auto repair manual PDF honda shadow 2005 750areo starter relay and wiring harness, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda shadow 2005 750areo starter relay and wiring harness Direct Download speed 5282 Kb/s

  honda shadow 2005 750areo starter relay and wiring harness Full Version speed 6162 Kb/s



2002-2005 Honda VFR800/A Wire Harness Replacement Manual

0

Filed Under (Honda) by admin on 21-04-2011

download
If the 18P (light blue) connector is in abnormal condition as shown below, contact TechLine at (800) 421-1900, option 9. FRONT SUB-HARNESS REPLACEMENT 1. Remove the front sub-harness from the cowl stay hooks. Disconnect all the electrical components from the front sub-harness. 2. Temporarily set the main wire harness aside, and disconnect the 6P (natural) con- nector. Then, carefully remove the front sub-harness. 3. Install the new front sub-harness by con- necting the 14P (natural) and 18P (light blue) connectors. NOTE: For routing specifications, refer to the WIRING & HARNESS ROUTING SECTION on pages 7-8. 4. Attach the front sub-harness on the cowl stay hooks. Make sure the front sub-harness is routed elow the main sub-harness. ABNORMAL CONDITION STAY HOOKS 6P (NATURAL) CONNECTOR FRONT UB-HARNESS 14P (NATURAL) CONNECTOR 18P (LIGHT BLUE) CONNECTOR FRONT SUB-HARNESSSTAY HOOK Page 4 VFR800/A #4 4 of 12 NOVEMBER 2007 5. Place the front sub-harness between the radiator and the frame, and below the rec- tifier. Be careful not to damage the front sub-harness or other components. 6. Re-connect the front sub-harness to the 6P (natural) connector. 7. Secure the main wire harness and the front sub-harness using the longer wire band. 8. Secure the main wire harness and the upper side of the front sub-harness using the shorter wire band. Adjust the wire har- ness located within the frame and the radi- ator hose accordingly. 9. Secure the main wire harness fuse box to the front sub-harness using the shorter wire band. FRONT SUB-HARNESS STAY HOOK MAIN-HARNESS FRONT SUB-HARNESS FRONT SUB-HARNESS 6P CONNECTOR (Male) 6P CONNECTOR (Female) WIRE BAND (LONG) WIRE BAND (SHORT)
WIRE BAND (LONG) WIRE BAND (SHORT) MAIN WIRE HARNESS FUSE BO

Incoming search terms:

HARLEY-DAVIDSON Starter Relay Location Guide

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Touring 1998 – 2007 Additional Notes: Relay Location: Under Seat in rubber Boot Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 ***2004 – 2007 FLHR series bikes & 2007 FLHX require additional Adaptor AD-1 & DGD-1. Start Relay is in Power Distribution box. Replaces H-D Relay part# 31579-04 Softails 2000 – 2007 Additional Notes: 2000 is when the Softails changed to Twin Cams. Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Softails 1996 – 1999 Additional Notes: Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05
Dyna 2007 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Replace Batt 15A Fuse with Supplied Fuse Holder Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Tap 12v Fuse (Batt 15A) System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Dyna 2000 – 2005 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Battery connection is made direct to Battery Buss to right of Relay * see Pic3 Installation Notes: Remove Outer Cover, then Remove 4 bolts holding secondary protector plate in place. Relay is on the upper left. Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery Buss + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Pic3 Sportster 2004-2007

Incoming search terms:

TOYOTA COROLLA 1984-2006 VEHICLE WIRING VEHICLE WIRING REMOVAL

0

Filed Under (Toyota Manuals) by admin on 04-10-2011

download
IRING INFORMATION: 1984 Toyota Corolla FWD WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE OR WHITE/RED Ignition Harness STARTER WIRE BLACK/WHITE Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/ORANGE Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) BLUE/WHITE Harness In Driver’s Kick Panel POWER DOOR UNLOCK (-) BLUE/RED Harness In Driver’s Kick Panel PARKING LIGHTS (+) DK. GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (-) LT. GREEN Harness At Steering Column HEADLIGHTS (-) RED/WHITE Harness At Steering Column DOOR TRIGGER (-) RED/WHT OR BLK/WHT Harness At Fuse Box TRUNK TRIGGER COMMON WITH DOORS (Hatchback Only) TACHOMETER WIRE BLACK At Ignition Coil BRAKE WIRE (+) GREEN/WHITE Brake Pedal Switch HORN TRIGGER (-) GREEN/RED Steering Column LEFT FRONT WINDOW UP GREEN/BLACK At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/RED At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP GREEN Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN BLUE/WHITE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN RED/YELLOW Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP RED/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN BLUE/BLACK Harness In Driver’s Kick From Driver Doo

Incoming search terms:

HARLEY DAVIDSON ENGINE GUARD-MOUNTED FOG LAMP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
VRSC models: See Figure 3. Place the wire harness from the kit into the area in front of the battery. Do not block the air intake opening. All models except VRSC and 2004 and later XL models: See Figure 4. Install the wire harness from the kit. Place the relay in the opening of the frame under the seat area, and route the long leg of the harness forward along the frame backbone. 2004 and later XL models: See Figure 5. Remove the nuts retaining the ignition module (1) and temporarily reposition the module as shown. Place the relay in the recessed area (2) of the oil reservoir. Install the ignition module. Route the long leg of the harness along the frame backbone. CAUTION 1 WARNING -J02798 Figure 3. Install Fog Lamp Wiring Harness (VRSC Models) Place harness into this area but do not block air intake Air intake i04372 Battery Figure 4. Install Fog Lamp Wiring Harness (All Models Except VRSC. Dyna Model Shown) i02286.eps 1. Relay 2. Ground stud 3. Long leg of harness 2 1 3 2 of 6 Figure 2. Fog Lamp Wiring Harness Figure 1. Fog Lamp Schematic Ground To low beam To main circuit breaker Fuse N.O. Contact Switch Coil Fog lamp Fog lamp i01360a Relay 1. Fuse block 2. Relay 3. Connector to power 4. Ring terminals (Ground) 5. To fog lamps 6. Unterminated wire to low beam 7. Switch with boot and bracket 4 2 5 6 7 1 3 i05708 5. All 2003 and earlier models and VRSC: Cut the connector from the white power lead, and replace it with the ring terminal supplied in the kit. 6. All 2003 and earlier models, except VRSC: Connect the white wire with the ring terminal to the copper stud (BAT) terminal of the main circuit breaker. All 2004 and later models, except VRSC: Connect the white wire with connector to the B+ connector on the harness. All VRSC: Connect the white power lead to the battery positive terminal. 7. See Service Part illustration. Connect the black ground wires with the two ring terminals to the ground stud under the seat, or at any good electrical ground point. Secure the kit harness to the adjacent harnesses with cable straps (item 6) from the kit. When routing wires through the front fork, make sure the wires are clear of moving parts, to avoid pinching and possible short circuits. 8. Route the forward end of the harness past the steering head, and route the lamp switch leg of the harness along the left side of the handlebar to the clutch control. 9. See the Service Parts illustration. Obtain the switch mounting bracket (item 11) from the kit. Unscrew the boot from the lamp switch, and install the switch into the bracket. Replace the boot on the switch. NOTE If the boot becomes worn or damaged, or is lost, replace the boot to prevent moisture from entering the switch. See the Service Parts illustration (Item 12). 10. See Figure 6. Remove the lower screw (1) and washer from the clutch control clamp (3), and install the lamp switch and bracket assembly (2). Install the screw and washer and tighten to 60-80 in-lbs (7-9 Nm). 11. See the Service Parts illustration. Secure the lamp switch leg of the harness to the handlebar using the wire harness retainers already on the bike. Snap the retainers into the holes in the handlebar. 12. Remove the headlamp assembly. See HEADLAMP – REMOVAL instructions for the correct model in the Service Manual. CAUTION 3 of 6 -J02798 Figure 6. Install the Lamp Switch on the Clutch Control Clamp i04370 3 1 1. Lower clamp screw 2. Lamp switch and bracket assembly 3. Clutch control clamp 2 Figure 5. Install the Wiring Harness (2004 and Later Models) i05712 3

Incoming search terms:

HONDA GL-1500 Trailer Wire Harness with Relay INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 27-02-2011

download
Seat: (if optional accessory wire is to be used) After removing trunk pan, run a stiff piece of wire from the bottom of the left saddlebag frame behind the rear tire up until it comes out under the trunk. Then hook open end of wire harness to fish wire and tape with electrical tape. Pull the harness back down to the bottom of the saddlebag frame. Route the long part of harness wire around the back of the license plate light to the right side 6-pin vertical connector just in front of tail light assembly. Unplug the stock connector and plug wire harness in between the stock plugs. Do the same for the left side with the short side of the Y on the harness. Now pull the slack down from the bottom of the harness and tuck all of the wires under the frames tubes so that the pan can be reinstalled without any problems. You can now hook up the loose ends of the harness to any style connector to match your trailer connector using the following color codes: GREEN GROUND ORANGE- LEFT TURN YELLOW- BRAKE BLUE- RIGHT TURN BROWN- TAIL RED POWER . Note : This accessory is an electronic isolated trailer wire harness. It should be installed by a qualified mechanic . 1. Disconnect the negative from the battery. 2. Install the harness. 3. When connecting to the trailer make sure all wires are used for the proper use and are waterproof. Make sure there are not exposed wires. Consult the trailer manufacturer for proper wiring. 4. Reconnect the battery negative. Double check the functions

HONDA Ground Effects Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Wiring Installation: 1. Remove the four M8x1.25 socket head cap screws from the seat and remove the passenger handles and seat. 2. Remove both rear side covers, and right front side cover. 3. Remove the two M3 Phillips head screws and two trim clips from the right front storage pocket. 4. Place the three relays of the Ground Effects Ground Effects Ground Effects Ground Effects wiring harness underneath the relay box. 2001 2001 2001 2001 — – 2005 MODELS 2005 MODELS 2005 MODELS 2005 MODELS Route the long end of harness (blue wire and orange wire), behind the fuel tank to the brake lines. The shorter section of the harness will end at the brake lines. Continue along the brake lines to the main harness of the motorcycle to the shelter, then up through the shelter to the pocket area. 5. Locate the harness connectors under the pocket. Go to step 6. 2006 & NEWER MODELS 2006 & NEWER MODELS 2006 & NEWER MODELS 2006 & NEWER MODELS Route the long end of harness (blue wire and orange wire), under the relay box and connect to the Positions Relay. 6. Connect the orange wire to the orange wire with white tracer using a scotch-lok connector. Connect the blue wire to the light blue wire with white tracer using a scotch-lok connector. 7. Route the red and white wires behind the fuel tank, along the left side wiring harness to the fuse box. 8. Connect the RED wire with eyelet connector attached, to the positive side of the accessory terminal in the fuse box. 9. Connect the WHITE wire to the negative battery terminal. 10. Connect the brown wire with white tracer to the brown wire with white tracer (tail relay in relay box) using a scotch-lok connector. 11. Route the orange wire with black tracer and the white wire behind the fuel tank, with at least 6 inches of wire left hanging below the bike. 12. Reinstall the right fairing pocket with the two M3 Phillips head screws and two trim clips. 13. Replace the right front side cover and the right and left rear side covers. 14. Replace the seat and passenger grip handles with the four M8 x 1.25 socket head cap screws

Incoming search terms:

2001 YAMAHA TDM900 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 20-11-2010

download
CHECKING THE SWITCHES ELEC EAS00731 ELECTRICAL CHECKING THE SWITCHES Check each switch for damage or wear, proper connections, and also for continuity between the terminals. Refer to “CHECKING SWITCH CONTINUITY”. Damage/wear Repair or replace. Improperly connected Properly connect. Incorrect continuity reading Replace the switch. -3- ELECTRIC STARTING SYSTEM ELEC EAS00755 ELECTRIC STARTING SYSTEM CIRCUIT DIAGRAM -4- ELECTRIC STARTING SYSTEM ELEC 4 Main fuse 5 Battery 7 Starter relay 8 Starter motor 9 Main switch 12 Starting circuit cut-off relay 13 Sidestand switch 14 Neutral switch 49 Clutch switch 59 Engine stop switch 60 Start switch 61 Ignition fuse -5- ELECTRIC STARTING SYSTEM ELEC EAS00756 STARTING CIRCUIT CUT-OFF SYSTEM OPERATION If the engine stop switch is set to “” and the main switch is set to “ON” (both switches are closed), the starter motor can only operate if at least one of the following conditions is met: The transmission is in neutral (the neutral switch is closed). The clutch lever is pulled to the handlebar (the clutch switch is closed) and the side- stand is up (the sidestand switch is closed). The starting circuit cut-off relay prevents the starter motor from operating when neither of these conditions has been met. In this instance, the starting circuit cut-off relay is open so current cannot reach the starter motor. When at least one of the above conditions has been met the starting circuit cut-off relay is closed and the engine can be started by pressing the starter switch. WHEN THE TRANSMISSION IS IN NEUTRAL WHEN THE SIDESTAND IS UP AND THE CLUTCH LEVER IS PULLED TO THE HANDLEBAR 4. Starting circuit cut-off relay Disconnect the starting circuit cut-off relay from the wire harness. Connect the pocket tester (Ω 1) and battery (12 V) to the starting circuit cut-off relay terminals as shown. YES NO Replace the starting circuit cut-off relay. Does the starting circuit cut-off relay have continuity between blue/white and black? EAS00759 Continuity Tester positive probe sky blue Tester negative probe blue/yellow No conti- nuity 1 2 1 3 Tester positive probe sky blue Tester negative probe black/yellow Battery positive terminal red/black Battery negative terminal black/yellow 1 2 Tester positive prove blue/white Tester negative prove black 3 4 5. Starting circuit cut-off relay (diode) Disconnect the starting circuit cut-off relay from the wire harness. Connect the pocket tester (Ω 1) to the starting circuit cut-off relay terminals as shown. Measure the starting circuit cut-off relay for continuity as follows. Tester positive probe blue/green Tester negative probe blue/yellow 4 3 Tester positive probe black/yellow Tester negative probe sky blue 2 1 Tester positive probe blue/yellow Tester negative probe sky blue 3 1 Tester positive probe blue/yellow Tester negative probe blue/green 3 4 When you switch the tester’s positive and negative probes, the readings in the above chart will be reversed. Are the testing readings correct? YES NO Replace the starting circuit cut-off relay. NOTE: EAS00760

Incoming search terms:

SUZUKI SV 1000 RADIATOR (COOLING SYSTEM) SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FI SYSTEM MALFUNCTION CODE AND DEFECTIVE CONDITION MALFUNCTION CODE DETECTED ITEM DETECTED FAILURE CONDITION CHECK FOR COO NO FAULT C11 Camshaft position sen- sor The signal does not reach ECM for more than 3 sec . after receiving the starter signal . The camshaft position sensor wiring and mechanical parts (Camshaft position sensor, intake cam pin, wiring/coupler con- nection) C12 Crankshaft position sensor The signal does not reach ECM for more than 2 sec . after receiving the starter signal . The crankshaft position sensor wiring and mechanical parts (Crankshaft position sensor, wiring/coupler connection) C13 Intake air pressure sensor The sensor should produce following voltage . (0.50 V < sensor voltage < 4 .85 V) Without the above range, C13 is indicated. Intake air pressure sensor, wiring/coupler connection C14 Throttle position sen- sor The sensor should produce following voltage . (0.20 V < sensor voltage < 4 .80 V) Without the above range, C14 is indicated. Throttle position sensor, wiring/coupler connection C15 Engine coolant temperature sensor The sensor voltage should be the following. (0.15 V <_ sensor voltage < 4 .5 V) Without the above range, C15 is indicated. Engine coolant temperature sensor, wiring/coupler connection C21 Intake air temperature sensor The sensor voltage should be the following. (0.15 V < sensor voltage < 4 .5 V) Without the above range, C21 is indicated. Intake air temperature sensor, wiring/coupler connection C22 Atmospheric pressure sensor The sensor voltage should be the following. (0.50 V < sensor voltage < 4 .5 V) Without the above range, C22 is indicated. Atm. pressure sensor, wiring/coupler connection C23 Tip over sensor The sensor voltage should be the following for more than 2 sec . after ignition switch turns ON . (0 .20 V < sensor voltage < 4 .80 V) Without the above value, C23 is indicated. Tip over sensor, wiring/coupler connection C24 or C25 Ignition signalCrankshaft position sensor signal is produced and ECM determines the ignition signal but signal from ignition coil is interrupted continuous by 4 times or more. In this case, the code C24 or C25 is indicated. Ignition coil, wiring/coupler connection, power supply from the battery SERVICING INFORMATION 8 .3 C28 Secondary throttle valve actuator No operating voltage is supplied from the ECM, C28 is indicated. STVA can not operate. STVA lead wire/coupler, STVA C29 Secondary throttle valve position sensor The sensor should produce following voltage . (0.10 V < sensor voltage < 4 .90 V) Without the above range, C29 is indicated . Secondary throttle position sensor, wiring/coupler connection C31 Gear position signalGear position signal voltage should be higher than the following for more than 2 seconds. (Gear position switch voltage >_ 0 .6 V) Without the above value, C31 is indicated. Gear position sensor, wiring/coupler connection, gearshift cam, etc. C32 or C33 Fuel injector Crankshaft position sensor signal is produced and ECM determines the injection signal but fuel injection signal is interrupted continuous by 4 times or more. In this case, the code C32 or C33 is indicated. Injector, wiring/coupler connection, power supply to the injector C41 Fuel pump relay No voltage is applied to fuel pump although fuel pump relay is turned ON, or voltage is applied to fuel pump although fuel pump relay is turned OFF . Fuel pump relay, connecting lead, power source to fuel pump relay C42 Ignition switchIgnition switch signal is not input in the ECM . Ignition switch, lead wire/coupler C44 Heated oxygen sensor (HO2S) [For E-02, 19] During 02 feedback control, 02 sensor voltage is higher or lower than the specification . No signal is detected during engine operation or no electrical power is supplied from the battery . HO2S lead wire/coupler connection Battery voltage supply to the HO2S C49 PAIR control solenoid valve (PAIR valve) When no operating voltage is supplied from the ECM, C49 is indicated. PAIR valve can not operate. PAIR valve lead wire/coupler

Incoming search terms:

Audio Oil Pressure Alert Relay Installation Instructions

0

Filed Under (Tips and Review) by admin on 27-10-2010

download
Step 1) Wire Connection: Using 18-gauge automotive wire, connect the audio alert relay as shown in the Wiring Diagram – Figure 1. • Connect the supplied wire from #3 terminal on the audio alert relay to the oil pressure switch post. Note: The supplied wire is not reversible. The eyelet end must hook to the oil pressure switch. • Connect a wire from #2 terminal on the audio alert relay to the ignition switch post that receives power when the ignition switch is first turned on. • Connect a wire from #1 terminal on relay to the positive side of existing horn, or alternate sound device. • Note: The audio alert relay uses the oil pressure switch as its ground. On most motorcycles, this audio alert relay can be installed easily under the dash. Figure 1- Wiring Diagram Cot a Oil Pressure Switch Ignition Switch Audio Alert Relay 2 1 3 load Horn + + – Caution: Make sure all connections are insulated away from potential grounds. Do not disconnect any existing wire. Step 2) Testing : Turn ignition switch on and ensure oil pressure light is on. Leave ignition switch on. Wait 30 sec (T1) and ensure the audio alarm sounds for ½ second (T2). If the electrical test is successful, proceed to Step 3. If not, you may have to use a pezio alert in place of the horn. (Which is available at most Radio Shack stores.) If audio alert still doesn’t work, consult the wiring diagram and recheck all wiring connections. Verify timer set points have not been altered. If problems persist, contact us at (518) 884-9591. Step 3) Mount relay switch: Use standard zip ties (not provided) or similar means to mount the relay to dash mount post or dash base. Note: The timer relay can be mounted almost anywhere on the bike that will not be exposed to direct rain or weather

2005 Kawasaki ZX6R Power Commander Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the tail section by removing the undertail and removing the six screws for the tail section. 2 Prop the front of the fuel tank up. 3 Lay the PCIIIin the tail section and route theharness along side the stock wiring harness towards the throttle bodies (Fig. B&C). Fig. A Fig. B Fig. C 2005 Kawasaki ZX6R – PCIII USB – 2 i218-411 www.powercommander.com PCIII harness PCIII harness Remove these screws 4. Disconnect the stock wiring harness from the LOWERinjectors at the throttle bodies (Fig. D). 5. Plug the PCIII connectors in-line of the stock injectors and wiring harness. ORANGE – cylinder 1 YELLOW- cylinder 2 GREEN – cylinder 3 BLUE – cylinder 4 6. Locate the Throttle Position Sensor connector behind the throttle bodies. This is a WHITE 3 pin connector (Fig. F) Fig. D Fig. E Fig F 2005 Kawasaki ZX6R – PCIII USB – 3 i218-411 www.powercommander.com PCIII connectors TPS connector Disconnect Stock connectors 7. Plug the PCIII harness in-line of the stock wiring harness (Fig. G). 8. Attach the ground wire from the PCIII to the negative side of the battery (Fig. H)

Incoming search terms:

Incoming search terms: