honda silverwing scooter leg air deflectors

You search Auto repair manual PDF honda silverwing scooter leg air deflectors, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda silverwing scooter leg air deflectors Direct Download speed 5282 Kb/s

  honda silverwing scooter leg air deflectors Full Version speed 6162 Kb/s



Victory Freedom Engines Installation Instructions for S&S Air Cleaner Kit

0

Filed Under (Victory) by admin on 31-10-2010

download
1-Locate and remove the Intake Air Temperature Sensor (IATS) from the stock Polaris Victory air box. Locate the new position for the IATS on the bottom of the S&S air cleaner. Push the IATS in the lower air cleaner cover and turn1⁄ 4 turnin either direction, make sure you feel it lock into place. Inspect from the inside of the air cleaner to ensure that the barbs are locked into place. See Picture 1. 2-Using the stock Polaris Victory air box gasket (PN 5811908) and S&S supplied (Qty 4) M6 fasteners, assemble the lower air cleaner cover to the throttle body using 243 Blue Loctite®on the treads. Torque the M6 fasteners to 72-96 inch pounds. 3-Position the S&S pre-formed air filter onto the lower air cleaner cover ensuring that it fits into the machined groove. 4-Install the top air cleaner cover on top of the filter ensuring that it fits into the machined groove. 5-Make surethat the filter is situated in the machined grooves on both the top and bottom air cleaner covers. 6-Using 243 Blue Loctite on the threads of the S&S supplied (Qty 3) M6 fasteners tighten down top air cleaner cover evenly until seated. Finish torque the fasteners to 72-96 inch pounds. Now you’re ready for breather hose and barometric pressure hose routing. 7-Locate the S&S supplied 3⁄ 16 “reinforced hose and clamps. Push one end of the hose on the 3⁄ 16 “brass barb in the bottom air cleaner cover and slide clamp up around the end of the hose. The other end of the hose is for the Barometric Pressure Sensor (MAP). Route the hose towardthe back of the engine over the top of the rear rocker cover. 8-Remove the MAP sensor from the stock Polaris Victory air box. Remove the orange rubber gasket from the MAP sensor. Slide the S&S supplied clamp over the 3⁄ 16 “rubber hose that leads to the air cleaner. Push the barbed end of the MAP sensor into the 3⁄ 16 ” rubber hose and slide clamp up to the end of the hose around the barb. A small amount of lubricant may be applied to the barb on the MAP sensor to make installation easier. 2 S&S Air Cleaner Assembly 41-0021 (Calibration cardnot shown) Picture 1 CAUTION WARNING WARNING Plastic barb locked in recess.
9-Assemble and install breather hose as follows: A-Cut the stock Victory®hose on the straight section just behind the 90 degree bend as shown in Picture 2 . B-Slide an S&S supplied 1⁄ 2 “hose clamp over the modified stock breather hose. C-Install the S&S straight barb in Victory breather hose and position a hose clamp around hose end. D-Slide the 90-degree end of breather hose over the brass barb on the air cleaner cover and slide hose clamp in place. E-Position straight end of the S&S breather hose over the 1⁄ 2 “barb to connect to the Victory hose. Slide clamp over connection. F- See Pictures 3 and 4 for breather hose and barometric pressuresensor hose installation positions. NOTE: S&S breather hose can be cut for best fit

Incoming search terms:

HARLEY DAVIDSON ADJUSTABLE AIR DEFLECTOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION 1. See Figure 1. Models with NO air deflectors installed: Remove and discard the eight hole plugs (1) from the right and left edges of the inner fairing assembly. Models WITH air deflectors currently installed: Remove and discard the eight screws that retain the right and left air deflectors. Remove and discard the deflectors. 2. See Figure 2. Select a right-side (1) or left-side (2) air deflector, and four screws (3) from the kit. Determine the correct side by holding the mounting-hole side of the deflector against the fairing. 3. Place the deflector against the inner fairing, lining up the holes. Insert the screws through the deflector holes and into the fairing air deflector holes. Tighten the screws to 25-30 in-lbs (2.8-3.4 Nm) . 1 1 is04653a Figure 1. Remove Hole Plugs SERVICE PARTS 3 2 1 is04654 Figure 2. Service Parts: Adjustable Air Deflector Kit Table 1. Service Parts Table Part Number Description (Quantity) Item 58128-08A Air deflector, adjustable (right side) – Dark Smoke 1 57655-08A Air deflector, adjustable (right side) – Light Smoke 58129-08A Air deflector, adjustable (left side) – Dark Smoke 2 57657-08A Air deflector, adjustable (left side) – Light Smoke 2563 Screw (8

Incoming search terms:

Air Shock Installation Instructions

0

Filed Under (Tips and Review) by admin on 24-11-2010

download
Air HoseInstallation. Choose the most convenient loca- tiononyour motorcycle for the air fill valve. Drilla 5/16″hole and install the air fill valve as shown in Figure 3orsecure air fill valve to frame tube. 2. Keep hose ends clean during installation because dirt can cause air leaks. 3. Install hose connector, tube clamp and two O-rings onto one end of the air hose (See Figures4&5) Apply rubber lubricant (soap solution, not oil) to the O-rings to ease installation on the air hose& into the shock absorber inlet. Plastic connector should just bottom on fitting. Do not overtighten! The function of the nut is to hold everything together in place, the O- rings do the sealing. Fin- gertightenonly (10 in/lb maximum). 4. After routing the air hose, trim the length to fit air fill valve. Install hose connector, tube clamp, and twoO-rings onto end of hose (See figures 4&5). Lubricate as above and assemble to air fill valve. Use the same procedure formating hose. Important —leaveasmall amount of slack in hose near shock absorber to allow for the slight move- mentofthe shock. Caution! Do not install hose near ex- haustsystem, battery or any other sharp edges or seat movement. Keep hoses clear of moving parts such as wheels or suspension components. Do not allow hoses to have excess slack and sag below the motorcycle. The hoses could catch on road surfaces or debris and could be damaged while the motorcycle is in motion. 5. If necessary the air hose can be secured along the motorcycle’swiringharness with tie-wraps. 6. Testing: Inflate system to 50 psi. Apply soapy water solution to all connections and check for air leaks. If there are any leaks, disconnect the suspected fitting and check for dirt or damage to the air line or the O-rings. Remove any dirt or foreign matter, re-lubricate the O-rings and reinstall. If unable to locate the leak, remove rubber boot from shocks and submerge pressurized components under water (in- cludingT-Valve) and check for leaks. If you cannot solve the air leak problem, please contact our technical staff for assistance

Incoming search terms:

2009 Kawasaki ULTRA 250X/ 260X FUEL INJECTION CONTROLLERS And REGULATORS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The R&D high performance Air Filter Kit will improve acceleration and top speed performance by increasing air flow and reducing air temperatures that enter directly into the Ultra 250X’s air plenum box area. The O.E.M. air plenum box on the Ultra 250X is a great design that will flow plenty of air. However, the air that feeds the plenum box is heated by the engine. R&D has created an easy to install “flat filter” that installs directly in place of the large center access inspection cover located directly under the main glove box. The R&D Flat Air Filter insert will allow unrestricted fresh and cool air to enter the air plenum box area which will add power you can feel and a nice high performance tone. The R&D Performance Filter Kit also features two filters, one for each of the surge and blowoff protections valves. The O.E.M. surge valve recycles compressed hot air back into the air box plenum at idle and under deceleration conditions. The R&D surge and blowoff valve filter kit removes the air recycling hoses which will keep the hot air from entering the air plenum box reducing the engines intake air temperatures. The R&D Ultra 250X Air Filter Kit offers great performance tips on how to remove the restrictive air vent hoses which will further reduce the under seat ambient air temperatures. The R&D Filter system does not remove or alter the O.E.M. plenum box in any way, therefore there are no questions to be answered regarding water ingestion

Incoming search terms:

HONDA CBX 750F (RC17) OWNERS MANUAL

0

Filed Under (Honda) by admin on 26-11-2010

download
Front air pressure adjustment: 1. Place the motorcycle on its centre stand. Do not use the side stand, or you will get false pressure readings. 2. Remove the front fork air valve cap (1). Check the air pressure. NOTE: Some pressure will be lost when removing the gauge from the valve. Determine the amount of loss and compensate accordingly. 3. Add air to the recommended pressure. NOTE: We recommend that you do not exceed the recommended air pressure or the ride will be harsh and uncomfortable. 4. Reinstall the front fork air valve cap. Rear air pressure adjustment: 1. Place the motorcycle on its centre stand. 2. Do not use the side stand, or you will get false pressure readings. 3. Remove the right side cover. 4. Remove the valve air cap (2). Check the air pressure with an air pressure gauge. NOTE: Some pressure will be lost when removing the gauge from the valve. Determine the amount of loss and compensate accordingly. 5. If required, add air up to the recommended pressure. 6. Reinstall the air valve cap (2) and the right side cover

Triumph Bonneville America And Speedmaster The Freak Installation Instructions and Parts List

0

Filed Under (Triumph) by admin on 29-10-2010

download
INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. 1. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. A. Seats – Remove both seats starting with the passenger pillion, if applicable. B. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover. Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C . C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box. On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. D. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). E. Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap. Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first. Remove the battery. F. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. G. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector. Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. 2. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. A. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions. B. Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. C. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs. D. Remove the mufflers – Remove the mufflers by loosening the clamp at the exhaust header, and by removing the rear foot peg hangers. If the mufflers are not removed, they can become damaged by the axles in Section 2H . E. Disconnect the carburetors – With a small flathead screwdriver, pull the retainer springs out of the channel of the carburetor intake tubes (the two large black tubes coming from the air box into the back of each carburetor), and simply push them towards the air box off of the carbs

Incoming search terms:

MOUNTAIN BIKE AIR SHOCK SET-UP AND TUNING GUIDE

0

Filed Under (Tips and Review) by admin on 01-12-2010

download
DETAILED SET-UP 2. Installing Air Pressure – Remove the air cap from the Schrader valve on the end of the shock body. Attach the pump to the Schrader valve. Some people damage their pumps by screwing them on too far. As soon as the gauge registers pressure, screw 1/2 turn more and pump to the desired level. Use the release button on the pump to reduce air pressure. The hiss you hear when unscrewing the pump is only the air from the pump and not from the shock! Likewise, when you install the pump again, you will also hear a hiss as air from the shock fills the pump and reduces the registered pressure you previously installed. All perfectly normal when pressurizing the shock! After removing the pump, be sure to reinstall the Schrader valve cap. If the shock does not dampen properly after pressurizing, the air pressure may have been lost during pump removal as a result of a worn pump fitting o-ring that needs replacement. Do not ride the bike until the shock is properly pressurized. 3. Main Air Spring Pressure Adjustments – Air Spring adjustments are made by inflating or deflating the main air spring chamber. Since your IFP air pressure adjustment (outlined above) also affects your starting spring force, you should always adjust your IFP pressure before adjusting the main air spring pressure. You can refer to the online Quick Start guide at: www.progressivesuspension.com/literature.html for accurate main air spring pressure and sag settings matched to your bike model and body

Incoming search terms:

HARLEY DAVIDSON TOURING SUSPENSION AIR PUMP KIT OPERATION/ INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
OPERATION 1. Remove cap from air suspension air valve and connect pump by threading the air valve adapter (1) on the pump as shown in Figure 1. When adapter is threaded properly, the current air pressure in the system will be indicated on the gauge of the pump. Do not exceed maximum air pressure for rear suspension. Air components fill rapidly. Therefore, use low air line pressure. Failure to do so may result in possible damage to components. (00165a) NOTES See the motorcycle’s Owner’s Manual or, if installed, the air suspension lowering kit’s instruction sheet for the recommended air pressures. Using pressures outside the recommended loading range will result in a reduction of available suspension travel and reduced rider comfort. 2. To increase pressure, operate the air pump handle (4) until the desired pressure is indicated on gauge (2). Use caution when bleeding air from the suspension. Moisture combined with lubricant may leak onto the rear wheel, tire and/or brake components and adversely affect traction, which could result in death or serious injury. (00084a) NOTE The pressure release button is designed to release pressure slowly. If the button is completely or rapidly depressed, no air will be released. For the best results, depress the pressure release button slowly and only partially. 3. To decrease pressure, slowly depress the pressure release button (3) on the pump until desired pressure is indicated on gauge (2)

Incoming search terms:

WILDFIRE WFH50-S2 Gas Scooter Owner's Manual

0

Filed Under (Tips and Review) by admin on 21-11-2010

download
Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed. • Do not leave the main switch in the on position for an extended period of time if the engine is not running Off Position: • All electrical circuits are off and the engine is stopped. The key can be removed in this position. Steering Lock Position: • Turn the handlebars to the left as far as they will turn, turn the key to the lock position and remove. Steering Lock Position On Position Off Position Wildfire WFH50-S2 Maintenance Table The X indicates at how many miles you need to check the Item. Must change oil: change before riding, again at 500 miles and then 2500 or yearly which ever comes first. Capacities Fuel Capacity: 1 gallon Final drive oil capacity: 3.5 ounces Tire air pressure: Front 28 psi and rear 32 psi. ITEM 500 1000 20002500 3500 40004500 5000 60006500 Check Daily Engine Oil and Filter X X X X X X Gear Oil X X X X Valve Clearance X X Cam Chain X X Carburetor X X Air Cleaner Clean Every 1500 miles, Replace Every 3500 miles Fuel Filter Clean Every 1000 miles, Replace if Necessary Brake System X X X X X X X Drive Belt X Screws and Nuts X X X X X *When riding in a dusty environment, check and clean the air filter element more often. Battery • This scooter uses a sealed lead acid battery, it is unnecessary to check or add liquid. NOTE: Never open the electrolyte of a sealed battery. Remove the battery from the scooter and store separately in a well ventilated area when the scooter is not in operation for long periods of time Speedometer • Speed is measured in mph. Odometer • The total riding distance is indicated. Fuel gauge • The gauge indicates how much fuel is in the tank (the gauge does not work when the ignition switch is off). The needle moves from full “F” to empty “E” as your fuel decreases. Fill the tank with a good grade of 89-90 octane unleaded gasoline. High Beam Indicator LIght • The high beam light indicates that the high beam headlight is in use. NOTE: Apply the low beam to avoid obstructing the view of other drivers. Turn Signal Indication Light • The turn signals indicate that you are turning a chosen direction, push the button in the desired turning direction, it will return to the center, press the button in to turn off. Speedometer Odometer Turn Signal Indication Light High Beam Indication Light Fuel Gauge 4 General Safety Precaution • Scooters can be hazardous to operate. Please operate it with the following safety instruction. If you fail to take proper precautions, a collision or fall may quickly occur. If you have any questions as to the operating condition of your scooter, turn off the engine and walk your scooter. These scooters should be ridden by persons with good vision, balance, coordination, reflex, strength and decision making capability. • Please read this manual and all safety labels carefully, and follow correct operating procedures. • Before each time you ride make sure that the brakes work properly. • Never operate your scooter without wearing proper safety equipment that includes helmet, shoes, etc… • Never operate your scooter under influence of alcohol or drugs. • Always ride with both hands on the handle bars. • Never operate at excessive speeds. Proper speed is determined by terrain, visibility, operating condition and experience. • Never attempt wheelies, jumps or other stunts. • Always inspect your scooter prior to each use to make sure all bolts are tight, and is in safe operating condition.

Incoming search terms:

Wildfire WFH 150-T Touring Scooter Specification And Owner's Manual

0

Filed Under (Wildfire) by admin on 29-11-2010

download
Engine Oil Replacement • Replace the engine oil after the first 50 miles or 1 hour with 5w50, 10w50 or 15W50 synthetic engine oil. Then replace again every 1,500 miles or 1 each year. Check oil level every 500 miles, add oil if needed. Changing the Engine Oil (1).Warm up the engine for a few minutes. (2).Stop the engine. (3). Place scooter on center stand. (4).Place an oil pan under the engine and remove the dipstick. (5).Remove the drain plug and drain the oil. Reach in drain hole, pull out filter clean and reinstall, after all oil drains out. (6).Reinstall drain plug. (7). Fill the engine with oil until the level is in the designated area on the dipstick. (8).Start the engine and check for oil leaks. If a leak is found stop the engine immediately and look for cause. Rear Wheel Oil Replacement • Replace the gear oil after the first 500 miles with 5W/50 synthetic engine oil. Replace the gear oil again every 4 months or every 2000 miles. • Replacing the Gear Oil (1).Put the scooter on the center stand (please see photo below) . (2).Place an oil pan under the gear case (please see photo below) . (3).Remove the oil filler bolt and the drain plug to drain the oil (please see photo below) . (4).Reinstall and tighten the drain plug. (5).Fill the gear case with oil (please see photo below) . (6).Reinstall the oil filler bolt. (7).Check for oil leakage. Cleaning Air Cleaner Be sure to check the air cleaner regularly. (1).Place the scooter on the center stand. (2).Unscrew and remove the left side panel. (3).Remove the air cleaner cover by removing the screws. (4).Take out the air cleaner by removing the screws. (5).Remove the air cleaner element and wash it gently, but thoroughly in solvent. Replace if damaged. (6).Squeeze out the excess solvent and dry it. (7).Apply oil to the entire surface of the air cleaner and squeeze out the excess oil. It should be damp but not dripping. (8).Install the air cleaner, cleaner cover, and left side panel. center stand 1 oil pan 2 3 oil drain plug oil pan 5 Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed.

Incoming search terms:

Incoming search terms: