honda tmx 125 kickstarter spring

You search Auto repair manual PDF honda tmx 125 kickstarter spring, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda tmx 125 kickstarter spring Direct Download speed 5282 Kb/s

  honda tmx 125 kickstarter spring Full Version speed 6162 Kb/s



Honda ATV 650 Lift Kit REMOVAL AND Installation

0

Filed Under (Honda) by admin on 14-01-2012

download
Place jack under center on the ATV front end and lift until front wheels clear the ground. Be careful to support ATV properly so that it is secure, but so that the A-arms and shocks can droop to full extension. 2. Remove front wheels and shocks. 3. Using a shock spring compressor, compress the spring on the shock and remove the spring retaining ring.
CAUTION: The spring is installed under tension. Failure to use a shock spring compressor could cause loss of control of the spring, which could unload rapidly causing bodily injury. If you do not have a shock spring compressor you should acquire one or take it to a dealer or professional mechanic for installation of the stiffeners. 4. Remove the spring. 5. Insert the smaller front spring stiffener onto the shock with the lip of the spring stop, on the shock, mating into the recessed portion of the spring stiffener. 6. Slide the spring back onto the shock and it should rest on the lip of the spring stiffener.
7. Reattach the spring retaining ring. 8. Repeat steps for the opposite side. Once springs are complete reattach the top of the shock to the top shock mount on the ATV and the spring stiffener will be closest to the A-arm. 9. Take two of the “L” brackets and connect them to the bottom of the shock, the part that connects to the A-arms. 10. There is a top and bottom to the “L” bracket. See the diagram

Incoming search terms:

HONDA 450E/ S MOUNTING AND ARS ADJUSTMENT INSTALLATION

0

Filed Under (Honda) by admin on 24-12-2011

download
MULTI-RATE SPRINGS AND THE ARS SYSTEM Depending on the application dual–rate springs are fitted on the shocks. Dual-rate springs are just that– a spring set with two separate rates. This is done with a short spring stacked on a longer spring. As both springs collapse they produce a soft, or initial, rate. The spring set will maintain this initial rate until the short spring stops compressing. At that point, the spring rate “crosses over” to the stiffer, or final, rate. This multi-rate system allows a soft initial rate for comfort on small bumps, but has the capability of soaking up the big pot-holes and other off road hazards. ARS stands for Adjustable Rate Suspension. ARS is available on some dual-rate spring 4-wheel ATV shocks. ARS differs from spring preload. The ARS system allows the rider to increase or decrease the load-carrying capacity of the shocks by turning a lever. Depending on the application and spring set, the rider can increase the load capacity of the shocks up to 50 percent. The average preloader that makes a half-inch increase in preload will HONDA 450E/S MOUNTING & ARS ADJUSTMENT INSTRUCTIONS Continued on next page. #TRX450 – 5/28/99 #TRX450 – 5/28/99 Fig. 1. Front shock installation. Note that the shock body is at the top with the shaft pointing down. ARS shown is in the unloaded position. Fig. 2. Rear shock mounting with ARS. Position the lever so that it will not come in contact with any vehicle parts around it. The cup can be rotated to reposition the lever if necessary.
increase the capacity of the shocks to only about 5 to 10 percent. ARS allows the shocks to be correct for solo riding, but still handle the increased weight of an added load. ARS can also be employed to stiffen the rates for aggressive riding. The ARS system consists of an indexing lever and a stepped cup that contains the short spring of the dual- rate. The position of the lever in relation to the steps in the cup determines how long the spring set remains on the soft, or initial, spring rate. On most ARS applications, four positions can be selected from full stiff to full soft. Indexing is done in a matter of seconds by rotating the lever or the cup by hand. Indexing the cup to the lever is usually preferable to avoid interference. Adjustment of the ARS system should only be made while the vehicle is unloaded to reduce the load on the springs. NOTE: It is important to make sure that a step in the cup is positioned directly over the tang on the lever. This will prevent damage to the cup and/or lever that can be caused by making partial contact between the tang and a step. In addition, make sure that the lever will not contact any vehicle parts around it, as the suspension moves up. TUNING TIPS—The “softest” setting on the ARS does not mean that the ride will be the most comfortable at that setting. It means that this is the softest spring setting which would be employed on smooth trails or without a load. Excessive suspension bottoming caused by rough conditions or by the addition of a large load will cause a harsh ride when the shock is adjusted to this setting. To eliminate this bottoming, adjust the ARS to the stiffer positions for a more comfortable ride. Hence, sometimes “stiffer is softer.” NITROGEN PRESSURES IN EMULSION SHOCKS

Incoming search terms:

KTM Enduro Engineering Shock Spring Removal And Installation Instructions

0

Filed Under (KTM) by admin on 12-11-2010

download
1 Place motorcycle on a stand so that the rear wheel is off the ground. 2 Remove the upper shock bolt. (Figure 1) 3 Remove the lower shock bolt. (Figure 2) 4 Remove the shock from the motorcycle by sliding it down and out the right rear side of the bike. (Figure 3) 5 Place the shock upside down in a vice with soft jaws. Loosen the retaining ring lock screw with a 4mm Allen wrench. (Figure 4) 6 Using EE KTM shock wrench #22-300 (Figure 5), loosen the retaining collar enough to provide ¾ clearance between the bottom of the spring and the spring retaining collar. (Figure 6) 7 Push the spring retaining collar down to access the retaining clip. (Figure 7) 8 Remove the retaining clip. 9 Remove the spring retaining collar by sliding it up and off of the shock clevis. (Figure 8) 10 Slide the shock spring up and off of the shock. 11 Slide the new spring onto the shock. It should be sitting on the adjusting collar. 12 Re-install the spring retaining collar by sliding it over the clevis far enough to allow the retaining clip to be installed. 13 Install the retaining clip. Make sure that it is fully seated in the groove. 14 Slide the spring retaining collar up until it bottoms out on the retaining clip. 15 Tighten the spring adjusting collar until the bottom of the spring contacts the spring retaining collar. Turn the spring adjusting collar a couple more turns to put a small amount of pre-load on the spring. 16 Remove the shock from the vice and re-install it on the bike by reversing removal steps. Make sure to torque the upper and lower shock bolts to the manufacturer’s torque spec. 17 Set static and race sag as specified in your owner’s manual. Remember to torque the adjusting collar lock screw to manufacturer’s specification

Incoming search terms:

HONDA NRX RUNE CALIPER COVERS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Starting on the right side hold the cover in place over the brake caliper. See photo (1), note how the spring when installed wraps around the bleeder screw (1A) at the front of the cover. See photo (2), note how the spring at the rear of the cover is routed behind the brake pad retaining pin. Using one of the springs supplied hook both ends of the spring into the holes at the front edge of the cover. Clean the face of the caliper (area marked “Nissin”) with rubbing alcohol. Peel the backing from the adhesive tape on the inside of the cover. Carefully position the cover in place aligning it with the suspension arm and being sure it is seated flat against the caliper. Press firmly to secure the tape to the caliper. Next stretch the spring over the bleeder as shown in photo (1A). At the rear of the cover route the spring behind the brake pad retaining pin as shown in photo (2A). Hook the spring into the upper hole then using a piece of fine wire or string (dental floss works good) hook onto the open end of the spring as shown in photo (3). Pull the hook into the hole in the cover. Remove the wire or string. Check again to see that the cover is seated on the caliper and that the springs are secure and not interfering with the moving parts of the brakes. 2. Repeat on the left side caliper. Rear Caliper Cover 1. Set the cover in place over the caliper. Notice that you need to hook the top of the cover over the caliper and the location of the two small spring holes at the front and back of the cover. The long spring supplied will attach to the front hole, pass between the caliper housing and the backside of the brake pad, then attach to the rear hole

HONDA 420 RANCHER 2×4/4×4 2007-2009 CLUTCH KIT INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-12-2011

download
Remove key from the ignition switch. Remove the side panels from both sides. Remove both foot wells. 2. Drain coolant. Remove the oil drain plug from the motor; if you carefully drain it into a clean container you should be able to reuse it. 3. Disconnect shift motor (on electric shift models only). Remove coolant hoses. 4. Remove the bolts that mount the front differential to the frame, no other parts need to be removed. Carefully slide the front differential towards the front of the machine; you might need to lift up slightly to get the differential to move. Remove the drive shaft. Remove o-ring on output shaft (on motor). 5. Remove the fuel pump. 6. Loosen the front crankcase cover bolts, keep track of each bolt length and location. Slowly remove the crankcase cover. Carefully watch for o-ring shims and dowel pins that may fall out. 7. Unstake the nut holding the clutch on and remove nut. Using Honda tool #07933-HB3000A thread the large part of the tool into the center of the clutch. Tighten the center bolt on the tool while holding the large part of the tool with a wrench. This will pull the clutch off the machine. Place the clutch on a clean work surface. EPI performance.com
8. Using the c-clamps push down slightly on the outside cover and remove the four e-clips. Keeping track of which way they come off, remove the round metal plates one at a time. This will allow you to see the complete spring. Remove one end of each spring using a spring tool or needle nose pliers and then remove springs. Install the EPI springs by inserting the spring into the outer edge first. Using a spring tool or pliers (45 degree bent pliers work well) pull on the spring and insert the end into the hole. Install the metal plates and the e-clips. If you can’t get the plates to sit flat make sure each clutch arm is flat against the bottom plate of the clutch. Occasionally when you put the springs on, the clutch arms will pop up. Slide the clutch into the machine. The Sprague clutch is marked “outside” when installing make sure this is facing out. Torque clutch nut to 87 ft/lbs. 9. Clean the gasket surface on the motor and on the cover. Put a thin layer of Honda Bond or Yamabond semi-drying liquid gasket (or something similar as long as it is semi-drying) on the crankcase cover. Carefully install crankcase cover, do not force cover on. Torque bolts to 9 ft/lbs. 10. Install the fuel pump. 11. Install the o-ring on the output shaft (on motor) and install the drive shaft. Carefully slide the front differential back into place and mount to the frame. Install the coolant hoses. Refill your engine coolant to the proper level according to your owner’s manual. 12. Install the oil drain plug. Refill your engine to the proper level according to your owner’s manual. You can reuse your oil if it is clean and was drained into a clean container. Only use manufactures recommended oil. 13. Be sure to double check coolant and oil levels and to look for any leaks after the machine has run for a few minutes. 14. Go out and ride your machine. If your performance doesn’t seem right double check to make sure everything has been done properly. 15. EPI is constantly testing our products. Sometimes there is a need to contact the user with new technical information. To ensure that you are receiving this information visit our web site EPIperformance.com to register your clutch kit.

Incoming search terms:

HARLEY DAVIDSON FL SOFTAIL PROFILE LOW FRONT SUSPENSION KIT INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-11-2010

download
Fork Spring Removal 1. Elevate and support the vehicle so the front tire is off the floor and the forks are fully extended. 4 9 3 1 10 11 2 5 6 7 8 is04004 1. Slider tube cap 2. Spacer washer 3. Oil seal 4. Clamp bolt and washer 5. Fork tube plug 6. O-ring 7. Fork spring 8. Tight-wound end of spring 9. Fork slider tube 10. Fork slider 11. Drain screw and washer Figure 1. Front Fork NOTE Remove the brake caliper from the fork slider. DO NOT remove the brake line from the caliper. 2. Remove the front wheel. See FRONT WHEEL: FLSTC/FLSTF/FLSTN in the Service Manual. 3. Remove the front fender. See FRONT FENDER in the Service Manual. 4. See Figure 1. Remove the slider tube cap (1), spacer (2) and oil seal (3) from the top of one fork side. Save the cap and spacer. The oil seal can be discarded. 5. Loosen the clamp bolt (4) and pull the fork from the brackets. 6. Repeat Steps 4 and 5 for the other fork side. -J00280 1 of 4 Wear saf ety glasses or gog gles when ser vicing f ork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) NOTE Be careful not to damage the O-ring. 7. See Figure 1. Remove the fork tube plug (5) and O-ring (6). Pull the spring (7) out of the slider tube (9). Remove the drain screw and washer (11), and drain the fork. Reinstall the drain screw and washer, and tighten to 52-78 in-lbs (5.9-8.9 Nm). 8. Repeat Step 7 for the other fork side. NOTE The Profile® Low Front Suspension Kit requires a different amount of H-D TYPE E FORK OIL than is listed in the Service Manual. NOTE Measure the oil level from the top of the fork tube with the fork spring removed and the fork fully compressed. 9. See FRONT FORK OIL in the Service Manual, but substitute the measures below. Fill the forks with Harley- Davidson TYPE E FORK OIL: • 1986 through 1999 models: •11.7 oz (345 cc) of oil, or •5.2 inch (132 mm) from top of oil level to top of tube. • 2000 and later models: •13.4 oz (396 cc) of oil, or •4.1 inch (104 mm) from top of oil level to top of tube. Fork Spring Installation 1. Insert a new Profile Low spring (7) from the kit into each slider tube (9), with the tight-wound portion (8) toward the bottom of the fork slider. NOTE Be careful not to damage the O-ring. 2. Install the fork tube plug (5) and O-ring (6) assembly into the slider tube and tighten securely. Be sure that one flat on each fork tube plug faces toward the inside of the fork. 3. Insert both fork side assemblies up through the slider covers, the fork stem and bracket, and the upper bracket. 4. Obtain two new oil seals (3), H-D Part Number 45733-48, and the spacer washers (2) and slider tube caps (1) saved earlier. Place an oil seal, followed by a spacer washer, onto each fork tube plug. 5. Insert the threads of a slider tube cap through each washer and seal, and into the fork tube plugs. Tighten to 40-60 ft- lbs (54.2-81.3 Nm). 6. Tighten the fork stem bracket clamp bolts (4) to 30-35 ft- lbs (40.7-47.5 Nm). 7. Install the front fender. See FRONT FENDER in the Service Manual. Install the front wheel and brake caliper. See FRONT WHEEL: FLSTC/FLSTF/FLSTN in the Service Manual. Jiffy Stand Removal/Installation 1. Move the jiffy stand to the retracted (up) position. Wear safety glasses or goggles when removing or installing spring. Spring tension can cause spring, attached components and/or hand tools to fly out which could result in death or serious injury. (00477c) 2. See Figure 3. Unfasten the jiffy stand leg spring (A) from the vehicle. Remove the hex bolt (B), lock washer (C), flat washer (D) and leg stop (E) from the threaded end of the jiffy stand leg. Discard the jiffy stand leg, but retain all other components. 3. Clean and inspect the jiffy stand attaching parts and mounting bracket for wear or damage. If parts replacement is necessary, refer to the Jiffy Stand section of your Service Manual for replacement procedures

Street Fork Spring Installation Instructions

0

Filed Under (Tips and Review) by admin on 13-02-2011

download
1. Remove fork springs according to instructions contained in your shop manual. For maximum performance we highly recommend that the forks be thoroughly cleaned, inspected and new fork oil installed. Note: If your motorcycle comes equipped with two fork springs in each leg (long & short), remove and discard both springs and the flat washer between the springs. If a stock spacer exits, remove it. If there is a short spring on the damper rod, do not remove it! 2. Use the recommended fork oil viscosity as noted in your owners manual with the following exceptions: GL1100 20 weight, GL1200/1500 15 weight required. See fine tuning for more in- formation. Fork oil level/volume should be checked according to the steps outlined in your authorized shop manual. Measurement of your fork oil by level is the preferred method. However, some manuals only specify a volume measurement. Due to the design of a progressive wound fork spring it will displace more oil thus requiring a maximum oil level of 5.5″ (140mm). Caution: This is not a recommendation, it is only a precautionary statement. If your manual specifies an oil level higher than 5.5″ (140mm) set the oil level at 5.5″ (140mm). (Oil level is the distance from the top of the fork tube to the top of the oil with the fork completely collapsed and the fork spring removed see figure 1.) This measurement can be made by using either one of the Progressive Suspension Fork Oil Level Adjusters (FOL-1 or FOL-2). 3. Install your new fork springs into the forks. Mechanically, it makes no difference which way the springs are installed. Some manuals will state; install the spring with the close wound end towards the bottom. This is done because sometimes there will be less spring noise. The springs will perform exactly the same regardless of which direction they are placed. Check the spacer length requirement for your motorcycle in the enclosed supplement. If not listed, you must calculate the pre-load. What is pre-load? Pre-load is the distance the spring compresses when the fork cap is installed. You may or may not utilize a spacer to achieve proper pre-load. The spacer in itself is not “pre-load”. It just helps to achieve it. Why is pre-load important? It determines the proper ride height which in turn affects how the bike handles.

FC Shock Spring Installation Guide

0

Filed Under (Tips and Review) by admin on 14-12-2010

download
Installation: 1. Remove the fork springs according to the OEM Owner’s Manual. 2. Check/adjust fork oil level and weight according to OEM Specifications. Caution: Most inverted forks will not require the use of any shim washers or spacers. In cases where use is necessary with the twin chamber style fork, the shims must be placed at the bottom of the spring. Most conventional forks (non-inverted) will use shim washers or spacers at the top of the fork spring. 3. Install Factory Connection fork springs and refer to OEM Owner’s Manual for proper assembly procedures. 4. Be sure to double check all fasteners. Note: Most modern day forks require special tools for disassembly and assembly of the components. Examples : Showa 47/49mm Twin Chamber, KYB 48mm Twin Chamber, WP 07 SX Models/SXS Components. Installing fork springs is an intricate process that should be performed with extreme care by a qualified suspension technician. Failure to install the springs correctly could cause damage to one or more components of the fork. This damage, although not readily apparent, could lead to unexpected failure or rider injury. Factory Connection manufactures models specific fork springs. Installation of a Factory Connection spring not designed for your motorcycle may result in unexpected failure and rider injury. Please consult your Factory Connection spring dealer or call Factory Connection directly if you are unsure about a spring/or springs. 1. Factory Connection’s Limited Lifetime Warranty Factory Connection warrants, to the original retail purchaser (“consumer”) who retains ownership of the vehicle on which the suspension spring(s) (“products(s)”) was originally installed, all suspension springs for life against factory defects in material and workmanship (other than defects in finish) when used under normal use and operating conditions. 2. Your Remedy Upon verification of warranty coverage, Factory Connection at its option will replace defective or prematurely worn-out product (s), without charge, or refund the purchase price of the products(s). This is the Consumer’s sole and exclusive remedy for any loss or damage, however arising, due to a nonconformity or defect in the product(s). 3. Warranty Claim Procedure To make claim under this warranty, the consumer should contact the Factory Connection dealer or Factory Connection where the product(s) was purchased. Factory Connection reserves the right to test the returned product(s) to evaluate the nonconformity or possible defect. The Consumer is responsible for all costs of returning the defective or prematurely worn-out product(s) to the Factory Connection dealer as well as all costs for removing the product(s) from and installing the products(s) on the vehicle.

Harley Davidson 39 mm Front Spring Lowering Kit INSTALLATION PROCEDURE

0

Filed Under (Harley Davidson) by admin on 07-04-2012

download
1. Support the motorcycle so the front wheel is off the ground. Next remove the front wheel and fender. Remove the fork cap nuts and loosen the lower triple clamp pinch bolts. Remove the front brake caliper. Some models have a tapered end to the fork tube. Extra effort will be required to remove the tube from the crown. Loosen the top fork cap 1 to 2 revolutions. Use a soft wood block or similar tool (that will not mark fork cap finish) and tap down with mallet to loosen fork tube from its tapered fit in top steering crown. Make sure fork pinch bolts are loose. To completely remove fork of this style, unscrew the fork cap entirely. 2. Slide both fork assemblies out of the triple clamps. Unscrew the top fork tube plugs. Remove the plugs and fork springs. CAUTION: Fork caps are under spring pressure and could cause serious injury. Drain the fork oil by turning the fork assemblys upside-down. 3. Next, bottom the fork tube into the fork leg. DO NOT extend the tube while you remove the allen bolt on the bottom of the fork leg. Turn the assembly upside-down and shake the damper rod and rebound spring out of the fork assembly. Again, DO NOT extend the tube during this. Extending the tube could dislodge the internal bottoming cone, which fits on the end of the damping rod, making it very difficult to reinstall the damper rod without complete fork disassembly. 4. FOR 1″ REDUCTION IN FORK LENGTH: You must first measure the length of the O.E.M. rebound spring. Depending on the model of the motorcycle, the length will either be 1″ or 2″ long. A. If you currently have a 1″ rebound spring, you need to replace it with the 2″ long LA Choppers rebound spring (included in the kit), then reinstall the damper rod in the fork tube. B. If you currently have a 2″ rebound spring, you will need to add the 1″ long spacer, then reinstall the damper rod in the fork tube.

2008 Honda CBR1000RR Clutch Inner Installation PROCEDURE

0

Filed Under (Honda) by admin on 23-04-2011

download
Refer to the 2008 CBR1000RR Service Manual for specific removal instructions. While completing this procedure, be careful not to damage the covers, cowls, or any other components. 1. Remove the air intake cover (page 3-8). 2. Remove the upper inner cover (page 3-9). 3. Remove the lower cowl (page 3-9). 4. Remove the right middle cowl (page 3-10). 5. Remove the right crankcase cover (page 10-5). Clutch Removal (page 10-7) 6. Remove the starter idle gear and shaft. 7. Remove the snap ring and stopper ring. 8. Remove the clutch lifter piece and plate. 9. Unstake the clutch center lock nut. Be careful not to damage the mainshaft threads. 10. Hold the pressure plate with the special tool. You must use the special tool (Clutch Holder, T/N 070MB-MFLA100) when removing the lock nut. Using an impact wrench will damage the main shaft threads. Clutch Holder: 070MB-MFLA100 (autoshipped in May 2008) 11. Remove the clutch center lock nut and washer and discard the lock nut as shown on top of page 3 12. Remove the clutch spring holder, spring seat, and two clutch springs. 13. Remove the spring seat. 14. Remove the following: • Pressure plate
• Spring seat • Judder spring • Clutch disc A • Clutch plate A • Seven clutch discs B • Clutch disc C  Clutch center NOTE: Do not remove the clutch outer. New Clutch Installation (page 10-20) NOTE: The new clutch disc assembly has a dif- ferent order of plates than the illustration shown in the Service Manual. Keep note of this when repairing updated units.
15. Install the new clutch disc assembly with- out removing the setting bolts. Rotate the main shaft to align the clutch disc assem- bly with the main shaft spline. 16. Slightly loosen the setting bolts. 17. Rotate clutch disc C to align its tabs into clutch outer shallow slots, then fully install the clutch disc assembly. 18. Remove and discard the setting bolts. 19. Install the spring seat

Incoming search terms: