honda valkyrie kickstand spring component

You search Auto repair manual PDF honda valkyrie kickstand spring component, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda valkyrie kickstand spring component Direct Download speed 5282 Kb/s

  honda valkyrie kickstand spring component Full Version speed 6162 Kb/s



Honda ATV 650 Lift Kit REMOVAL AND Installation

0

Filed Under (Honda) by admin on 14-01-2012

download
Place jack under center on the ATV front end and lift until front wheels clear the ground. Be careful to support ATV properly so that it is secure, but so that the A-arms and shocks can droop to full extension. 2. Remove front wheels and shocks. 3. Using a shock spring compressor, compress the spring on the shock and remove the spring retaining ring.
CAUTION: The spring is installed under tension. Failure to use a shock spring compressor could cause loss of control of the spring, which could unload rapidly causing bodily injury. If you do not have a shock spring compressor you should acquire one or take it to a dealer or professional mechanic for installation of the stiffeners. 4. Remove the spring. 5. Insert the smaller front spring stiffener onto the shock with the lip of the spring stop, on the shock, mating into the recessed portion of the spring stiffener. 6. Slide the spring back onto the shock and it should rest on the lip of the spring stiffener.
7. Reattach the spring retaining ring. 8. Repeat steps for the opposite side. Once springs are complete reattach the top of the shock to the top shock mount on the ATV and the spring stiffener will be closest to the A-arm. 9. Take two of the “L” brackets and connect them to the bottom of the shock, the part that connects to the A-arms. 10. There is a top and bottom to the “L” bracket. See the diagram

Incoming search terms:

HONDA GL1500CD/ VALKYRIE Specifications

0

Filed Under (Honda) by admin on 29-01-2011

download
position when it comes to the environment. We continue to develop low-emission technologies for our current and future motorcycles, ATVs, scooters and personal watercraft. We already produce models that exceed the stringent 2008 CARB emissions requirements years ahead of schedule. And that’s the kind of performance everybody can appreciate. BE A RESPONSIBLE RIDER. Riding a motorcycle is an exercise in responsibility—to yourself, to others, to the environment and to the sport. So remember, wear a helmet, eye protection and protective clothing whenever you ride. Never ride under the influence of drugs or alcohol, and never use the street as a racetrack. Inspect your motorcycle before riding, read your owner’s manual, and see your local Honda Dealer concerning reimbursement through the Honda Rider’s Club of America™for Motorcycle Safety Foundation (MSF) rider training.* Always obey local laws, use common sense, and respect the rights of others when you ride. Make sure you have a proper license when riding on public roads, and never modify your motorcycle’s exhaust system. 03 SPECIFICATIONS ACCESSORIES VALKYRIE Log on to our website at honda.com for more information about Honda Genuine Accessories . On a bike like the Valkyrie, you can never have too much chrome. And that’s precisely why we offer our Chrome Sidecovers and Chrome Swingarm-Pivot cover to help really brighten up these areas. Here’s one of our most popular Valkyrie accessory options. These Leather Saddlebags look great, hold plenty, and match some of the other leather accessories we have available. Got a long trip planned, or is winter right around the corner? Then make sure you take a look at-or should we say take a look through-a Honda Genuine Accessories Windshield for your new Valkyrie. GL1500CD 1520cc liquid-cooled horizontally opposed six-cylinder with belt-driven overhead camshafts Six 28mm constant-velocity carburetors 71.0 x 64.0mm Solid-state digital Five-speed constant-mesh Shaft 150/80R-17 radial 180/70R-16 radial Dual-disc with twin-piston calipers 28.9 inches 66.5 inches 5.3 gallons, including 1.1 gallon reserve 681 pounds Black Windshield, leather saddlebags, chrome exhaust tips, chrome rear carrier, CB transceiver kit, passenger CB talk switch, studded backrest pad, studded main seat, studded rear seat, deluxe backrest pad

Incoming search terms:

HONDA 450E/ S MOUNTING AND ARS ADJUSTMENT INSTALLATION

0

Filed Under (Honda) by admin on 24-12-2011

download
MULTI-RATE SPRINGS AND THE ARS SYSTEM Depending on the application dual–rate springs are fitted on the shocks. Dual-rate springs are just that– a spring set with two separate rates. This is done with a short spring stacked on a longer spring. As both springs collapse they produce a soft, or initial, rate. The spring set will maintain this initial rate until the short spring stops compressing. At that point, the spring rate “crosses over” to the stiffer, or final, rate. This multi-rate system allows a soft initial rate for comfort on small bumps, but has the capability of soaking up the big pot-holes and other off road hazards. ARS stands for Adjustable Rate Suspension. ARS is available on some dual-rate spring 4-wheel ATV shocks. ARS differs from spring preload. The ARS system allows the rider to increase or decrease the load-carrying capacity of the shocks by turning a lever. Depending on the application and spring set, the rider can increase the load capacity of the shocks up to 50 percent. The average preloader that makes a half-inch increase in preload will HONDA 450E/S MOUNTING & ARS ADJUSTMENT INSTRUCTIONS Continued on next page. #TRX450 – 5/28/99 #TRX450 – 5/28/99 Fig. 1. Front shock installation. Note that the shock body is at the top with the shaft pointing down. ARS shown is in the unloaded position. Fig. 2. Rear shock mounting with ARS. Position the lever so that it will not come in contact with any vehicle parts around it. The cup can be rotated to reposition the lever if necessary.
increase the capacity of the shocks to only about 5 to 10 percent. ARS allows the shocks to be correct for solo riding, but still handle the increased weight of an added load. ARS can also be employed to stiffen the rates for aggressive riding. The ARS system consists of an indexing lever and a stepped cup that contains the short spring of the dual- rate. The position of the lever in relation to the steps in the cup determines how long the spring set remains on the soft, or initial, spring rate. On most ARS applications, four positions can be selected from full stiff to full soft. Indexing is done in a matter of seconds by rotating the lever or the cup by hand. Indexing the cup to the lever is usually preferable to avoid interference. Adjustment of the ARS system should only be made while the vehicle is unloaded to reduce the load on the springs. NOTE: It is important to make sure that a step in the cup is positioned directly over the tang on the lever. This will prevent damage to the cup and/or lever that can be caused by making partial contact between the tang and a step. In addition, make sure that the lever will not contact any vehicle parts around it, as the suspension moves up. TUNING TIPS—The “softest” setting on the ARS does not mean that the ride will be the most comfortable at that setting. It means that this is the softest spring setting which would be employed on smooth trails or without a load. Excessive suspension bottoming caused by rough conditions or by the addition of a large load will cause a harsh ride when the shock is adjusted to this setting. To eliminate this bottoming, adjust the ARS to the stiffer positions for a more comfortable ride. Hence, sometimes “stiffer is softer.” NITROGEN PRESSURES IN EMULSION SHOCKS

Honda Motorcycle Na vigation Kit

0

Filed Under (Honda) by admin on 28-11-2010

download
Honda Motorcycle Na vigation Kit Honda Motorcycle Navigation Kit G e n e r i c A c c e s s o r i e s 2 0 0 8 For your peace of mind Honda Genuine Accessories are carefully designed, researched and stringently test ed tot he highest standards. And since they’re all Honda approved you’llknowthat they’rejustastoughand well made as your Honda motorcycle. Please Note -All prices quoted are correct at time of printing and are subject to change without prior notice. y e a r w a r r a n t y GENUINE ACCESSORIES Honda Motorcycle Navigation Kit Model Part Number Description RRP Remarks NAKED CBF 600 08A 40MER800B CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY CBF 600 08A 40MER800A CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY ON/OFF XL700V 08A 40MFF800 * CONTAINS NA VI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EARPH ONE, MANUAL, 08A 30MFF800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY XL 1000V 08A 40MBT800 CONTAINSNAVI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EAR PH ONE, MANUAL, 08A 30MBT800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY TOURERS/SPORT TOUR ERS DN-01 08A 40MEH800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, AND BATTERY -CONTAINS 08A 30MEW800 ADDITIONALSTE ERIN G HANDLE C LAMPS FORV ISU AL INTE GRAT ION OF THE COMPONENT NT700V 08A 40MEW800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, BATTERY

Incoming search terms:

KTM Enduro Engineering Shock Spring Removal And Installation Instructions

0

Filed Under (KTM) by admin on 12-11-2010

download
1 Place motorcycle on a stand so that the rear wheel is off the ground. 2 Remove the upper shock bolt. (Figure 1) 3 Remove the lower shock bolt. (Figure 2) 4 Remove the shock from the motorcycle by sliding it down and out the right rear side of the bike. (Figure 3) 5 Place the shock upside down in a vice with soft jaws. Loosen the retaining ring lock screw with a 4mm Allen wrench. (Figure 4) 6 Using EE KTM shock wrench #22-300 (Figure 5), loosen the retaining collar enough to provide ¾ clearance between the bottom of the spring and the spring retaining collar. (Figure 6) 7 Push the spring retaining collar down to access the retaining clip. (Figure 7) 8 Remove the retaining clip. 9 Remove the spring retaining collar by sliding it up and off of the shock clevis. (Figure 8) 10 Slide the shock spring up and off of the shock. 11 Slide the new spring onto the shock. It should be sitting on the adjusting collar. 12 Re-install the spring retaining collar by sliding it over the clevis far enough to allow the retaining clip to be installed. 13 Install the retaining clip. Make sure that it is fully seated in the groove. 14 Slide the spring retaining collar up until it bottoms out on the retaining clip. 15 Tighten the spring adjusting collar until the bottom of the spring contacts the spring retaining collar. Turn the spring adjusting collar a couple more turns to put a small amount of pre-load on the spring. 16 Remove the shock from the vice and re-install it on the bike by reversing removal steps. Make sure to torque the upper and lower shock bolts to the manufacturer’s torque spec. 17 Set static and race sag as specified in your owner’s manual. Remember to torque the adjusting collar lock screw to manufacturer’s specification

Incoming search terms:

HONDA GL1800 CHROME KICKSTAND INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 27-02-2011

download
NOTE: Read instructions thoroughly before installing. 1. Place bike on center stand. 2. Remove side stand by first removing the spring. Warning: Keep hand and fingers away from spring. 3. Remove locknut behind stand (14mm). 4. Remove the 8mm nut holding the switch and remove switch. 5. Remove 14mm bolt and then the side stand. 6. Install the new Chrome Kickstand in reverse order using the ORIGINAL bolt, nuts and spring or use the original bolt, nut and Add On part 45-1636, Chrome Kickstand Spring

2007 KTM SX-F 250- 450 Kickstand Installation and Removal Manual Instructions

0

Filed Under (KTM) by admin on 26-01-2012

download
Remove the lower d bolt making sure you keep track of the order of the small parts for re-assembly. 2) Remove the lower in-frame bolt. 3) Install the supplied lower kickstand mounting bracket onto the frame at the lower chain roller boss. The counter bore should slide over and onto the frame boss. The chain roller should go back into place just how it came e supplied lower kickstand mounting bracket between it and the frame. Do not is bracket needs to pivot to align with the lower hole in the main . 4) Install the kickstand onto the bike using one of the provided M8x30mm flat head sub-frame to main-frame bolt location. Do not tighten yet. 5) Line up and install the other provided ad bolt thru the lower kickstand mounting hole into the supplied lower kickstand mounting bracket. 6) Now tighten all three bolts, two mounting bolts (front) and one lower kickstand mounting bracket 7) Periodically check the kickstand and all mounting bolts for tightness. Maintenance: Clean and lubricate the kickstand pivot area after each ride! We recommend using a heavy-duty chain lube. If necessary, you can remove the back cover plate for additional cleaning. Never remove the kickstand leg pivot bolt!

Incoming search terms:

HONDA NRX RUNE CALIPER COVERS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Starting on the right side hold the cover in place over the brake caliper. See photo (1), note how the spring when installed wraps around the bleeder screw (1A) at the front of the cover. See photo (2), note how the spring at the rear of the cover is routed behind the brake pad retaining pin. Using one of the springs supplied hook both ends of the spring into the holes at the front edge of the cover. Clean the face of the caliper (area marked “Nissin”) with rubbing alcohol. Peel the backing from the adhesive tape on the inside of the cover. Carefully position the cover in place aligning it with the suspension arm and being sure it is seated flat against the caliper. Press firmly to secure the tape to the caliper. Next stretch the spring over the bleeder as shown in photo (1A). At the rear of the cover route the spring behind the brake pad retaining pin as shown in photo (2A). Hook the spring into the upper hole then using a piece of fine wire or string (dental floss works good) hook onto the open end of the spring as shown in photo (3). Pull the hook into the hole in the cover. Remove the wire or string. Check again to see that the cover is seated on the caliper and that the springs are secure and not interfering with the moving parts of the brakes. 2. Repeat on the left side caliper. Rear Caliper Cover 1. Set the cover in place over the caliper. Notice that you need to hook the top of the cover over the caliper and the location of the two small spring holes at the front and back of the cover. The long spring supplied will attach to the front hole, pass between the caliper housing and the backside of the brake pad, then attach to the rear hole

Incoming search terms:

HONDA 420 RANCHER 2×4/4×4 2007-2009 CLUTCH KIT INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-12-2011

download
Remove key from the ignition switch. Remove the side panels from both sides. Remove both foot wells. 2. Drain coolant. Remove the oil drain plug from the motor; if you carefully drain it into a clean container you should be able to reuse it. 3. Disconnect shift motor (on electric shift models only). Remove coolant hoses. 4. Remove the bolts that mount the front differential to the frame, no other parts need to be removed. Carefully slide the front differential towards the front of the machine; you might need to lift up slightly to get the differential to move. Remove the drive shaft. Remove o-ring on output shaft (on motor). 5. Remove the fuel pump. 6. Loosen the front crankcase cover bolts, keep track of each bolt length and location. Slowly remove the crankcase cover. Carefully watch for o-ring shims and dowel pins that may fall out. 7. Unstake the nut holding the clutch on and remove nut. Using Honda tool #07933-HB3000A thread the large part of the tool into the center of the clutch. Tighten the center bolt on the tool while holding the large part of the tool with a wrench. This will pull the clutch off the machine. Place the clutch on a clean work surface. EPI performance.com
8. Using the c-clamps push down slightly on the outside cover and remove the four e-clips. Keeping track of which way they come off, remove the round metal plates one at a time. This will allow you to see the complete spring. Remove one end of each spring using a spring tool or needle nose pliers and then remove springs. Install the EPI springs by inserting the spring into the outer edge first. Using a spring tool or pliers (45 degree bent pliers work well) pull on the spring and insert the end into the hole. Install the metal plates and the e-clips. If you can’t get the plates to sit flat make sure each clutch arm is flat against the bottom plate of the clutch. Occasionally when you put the springs on, the clutch arms will pop up. Slide the clutch into the machine. The Sprague clutch is marked “outside” when installing make sure this is facing out. Torque clutch nut to 87 ft/lbs. 9. Clean the gasket surface on the motor and on the cover. Put a thin layer of Honda Bond or Yamabond semi-drying liquid gasket (or something similar as long as it is semi-drying) on the crankcase cover. Carefully install crankcase cover, do not force cover on. Torque bolts to 9 ft/lbs. 10. Install the fuel pump. 11. Install the o-ring on the output shaft (on motor) and install the drive shaft. Carefully slide the front differential back into place and mount to the frame. Install the coolant hoses. Refill your engine coolant to the proper level according to your owner’s manual. 12. Install the oil drain plug. Refill your engine to the proper level according to your owner’s manual. You can reuse your oil if it is clean and was drained into a clean container. Only use manufactures recommended oil. 13. Be sure to double check coolant and oil levels and to look for any leaks after the machine has run for a few minutes. 14. Go out and ride your machine. If your performance doesn’t seem right double check to make sure everything has been done properly. 15. EPI is constantly testing our products. Sometimes there is a need to contact the user with new technical information. To ensure that you are receiving this information visit our web site EPIperformance.com to register your clutch kit.

Incoming search terms:

HONDA VALKYRIE ADJUSTABLE PASSENGER BOARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Remove the stock pegs using a 14mm wrench on the backside of the peg and muffler mounting plate. NOTE: use the box end of the wrench as these bolts are very tight from the factory. 2. Loosen the two (2) 12mm acorn nuts that attach the mufflers the mounting plate on each side. Next remove two (2) 14mm bolts that attach the plates to the frame on each side. 3. Install the floorboards using the new bolts provided and tighten securely. Tighten the 12 mm acorn muffler mounting nuts on both sides. 4. Pulling the spring-loaded levers out and rotating the lever slightly to hold it in the out position can adjust the Boards. Adjust to the height desired; rotate the levers back to line up with the slots, rock the board and arm slightly so that the spring-loaded pin drops into the nearest hole.

Incoming search terms: