honda 400ex engine removal

You search Auto repair manual PDF honda 400ex engine removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda 400ex engine removal Direct Download speed 5282 Kb/s

  honda 400ex engine removal Full Version speed 6162 Kb/s



Honda CB100 engine INTRODUCTION

0

Filed Under (Honda) by admin on 13-11-2011

download
Fuel Injection System for One Cylinder Motor Cycle Engine. Fuel injection has been developed for many years. But its common application is limited on car’s engine. With many reason fuel injection systems in motorcycle one cylinder engine has not been widely used yet. Fuel Injection System allows the amount of fuel, injected to be controlled appropriate to engine parameters such as engine speed, amount of air inducted to cylinder, temperature, for each cycle, over the entire engine operating conditions. This fuel injection research is done to find out the Volumetric Efficiency of the intake manifold system, the amount of fuel need to be injected for each engine cycle, and the engine characteristics over variation of test conditions. This research based on Honda CB100 engine, at applied thermodynamic Laboratory of Mechanical Engineering Department, Faculty of Engineering University of Indonesia. Experiment data from this
research shows the characteristics of injector duration as functions of engine speed, intake pressure, on one cylinder engine and the results of this research shows a good Volumetric Efficiency of the intake manifold designed using CFD (Computational Fluid Dynamic)

HONDA CT110 SERIES MOTORCYCLE Cold engine Starting Procedure

0

Filed Under (Honda) by admin on 15-11-2011

download
Prime the engine before starting by cranking the engine several times with the kick starter. The ignition switch should be OFF, the choke lever Fully ON (A) and the throttle opened slightly. Flooded Engine If the engine fails to start after several repeated attempts, it may have become flooded with excess fuel. To clear the engine, turn off the engine stop switch and lower the choke lever to Fully OFF (B). Open the throttle fully and crank the engine several times with the kick starter. Turn the engine stop switch to RUN and open the throttle slightly; start the engine using the kick starter When service is required, remember that your authorized Honda dealer knows your motorcycle best and is fully equipped to maintain and repair it. The scheduled maintenance may also be performed by a qualified service facility that normally does this kind of work; or you may perform most of the work yourself it you are mechanically qualified and have the proper tools
and service data. • These instructions are based on the assumption that the motorcycle will be used exclusively for
its designed purpose. Sustained high speed operation, or operation in unusually wet or dusty conditions, will require more frequent service than specified in the MAINTENANCE SCHEDULE. Consult your authorized Honda dealer for ecommendations applicable to you individual needs
and use

HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

2004 Honda CRF450R OWNER’S MANUAL

0

Filed Under (Honda) by admin on 21-11-2010

download
motorcycle can be kickstarted with the transmission in gear by disengaging the clutch before operating the kickstarter. Check the engine oil, transmission oil and coolant levels before starting the engine (page 21, 23, 24). Cold Engine Starting: 1. Turn the fuel valve ON. 2. Shift the transmission into neutral. 3. If the temperature is 35°C (95°F) or below, pull the choke knob fully out. 4. If the temperature is below 0°C (32°F), open the throttle two or three times. (The engine requires a richer mixture for starting in cold weather. When the throttle is so opened, the accelerator pump will feed extra fuel to the cylinder, thereby facilitating starting in cold weather.) 5. With the throttle closed, operate the kickstarter starting from the top of the kickstarter stroke, kick through to the bottom with a rapid, continuous motion. (Do not open the throttle, As the carburetor is equipped with an accelerator pump, excessive fuel will be charged into the engine, and the spark plug will be fouled if the throttle is opened and closed repeatedly. Excessive fuel in the engine makes kick- starting difficult.) 6. About a minute after the engine starts, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. (1) FUEL FILL CAP (2) BREATHER TUBE WARNING (1) FUEL VALVE (2) CHOKE KNOB Warm Engine Starting: 1. Turn the fuel valve ON. 2. Shift the transmission into neutral. 3. Pull the hot start lever and kick-start the engine. (Do not open the throttle.) 4. As soon as the engine starts, release the hot start lever 1. Shift the transmission into neutral. 2. Pull the hot start lever and kick-start the engine. (Do not open the throttle.) 3. As soon as the engine starts, release the hot start lever. Starting the engine excessively charged with fuel by throttle blipping or other reasons: 1. Shift the transmission into neutral. 2. With the throttle fully opened, repeat kickstarter operation approximately 10 times very slowly to discharge excessive fuel from the engine. 3. Pull the hot start lever and kick-start the engine (Do not open the throttle.) 4. As soon as the engine starts, release the hot start lever. Stopping The Engine 1. Shift the transmission into neutral. 2. Turn the fuel valve OFF. 3. Lightly open the throttle 2 – 3 times, and then close it. 4. Depress and hold the engine stop button until the engine stops completely. NOTE: • Failure to close the fuel valve may cause the carburetor to overflow. (1) THROTTLE GRIP (2) ENGINE STOP BUTTON Break-In Procedure Help assure your CRF’s future reliability and performance by paying extra attention to how you ride during the first operating day or 15 miles (25 km). During this period, avoid full-throttle starts and rapid acceleration. This same procedure should be followed each time when: • Piston is replaced • Rings are replaced • Cylinder is replaced • Crankshaft or crank bearing are replaced

KTM 60 SX / 65 SX REPAIR MANUAL ENGINE

0

Filed Under (KTM) by admin on 12-11-2010

download
Carburetor adjustment Basic information about the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95). Mixing ratio 2-stroke motor oil : super fuel 1:40 . Basic information of changing the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB: high altitude or high temperatures  choose leaner carburetor adjustment low altitude or low temperatures  choose richer carburetor adjustment * WARNING * -ONLYUSE PREMIUM – GRADE GASOLINE ROZ 95 MIXED WITH HIGH – GRADE TWO – STROKE ENGINE OIL . OTHER TYPES OF GASOLINE CAN CAUSE ENGINE FAILURE , AND USE OF SAME WILL VOID YOUR WARRANTY . -ONLYUSE HIGH – GRADE 2- STROKE ENGINE OIL OF KNOWN BRANDS ( I . E .SHELL ADVANCE RACING X). -NOTENOUGH OIL OR LOW – GRADE OILCAN CAUSE EROSION OF THE PISTON . USING TOO MUCH OIL , THE ENGINE CAN START SMOKING AND FOUL THE SPARKPLUG . -INTHE CASE OFA LEANER ADJUSTMENT OF THE CARBURETOR PROCEED CAUTIOUSLY . ALWAYSREDUCETHEJETSIZEINSTEPSOFONENUMBERTOAVOID OVERHEATING AND PISTON SEIZURE . NOTE: If despite a changed adjustment the engine does not run properly, look for mechanical faults and check the ignition system. Basic information on carburetor wear As a result of engine vibrations, throttle valve, jet needle, and needle jet are subjected to increased wear. This wear may cause carburetor malfunction (e.g., overly rich mixture). Therefore, these parts should be replaced after 1000 hours of using. Idling range – A Operation with closed throttle valve. This range is influenced by the idle adjusting screw 1 . Only make adjustments when the engine is hot. The idling speed can be changed by turning the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Opening up – B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range – C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer

Related Item : yhs-fh_lsonsw (4)working range for carburetor part diagram (3)Victory 106 Engine Problems (2)ktm engine serial number (2)yamaha ttr 90 carburetor adjustment (2)ktm 85sx gy6 kick start diagram (2)ktm 65 diagram of valve on head (2)2000 yamaha rt100 carb adjustment (2)do I start 2 stroke scooter with throttle closed or partially open? (2)adjusting yamaha pw80 carburetor (2)