honda goldwing reverse switch

You search Auto repair manual PDF honda goldwing reverse switch, if there are search results will appear below. If search results do not exist, please search by others keyword.



  honda goldwing reverse switch Direct Download speed 5282 Kb/s

  honda goldwing reverse switch Full Version speed 6162 Kb/s



Harley-Davidson CHROME HANDLEBAR SWITCH CAP KITS installation and REMOVAL manual

0

Filed Under (Harley Davidson) by admin on 09-03-2012

download
1. Open or remove seat according to the instructions in the Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove left and right-hand switch housing assemblies. Refer to HANDLEBAR SWITCHES in Service Manual. NOTE It is not necessary to disconnect the switch wiring to replace the switch caps. 4. Remove individual switches from switch housing. Refer to SWITCH REPAIR/REPLACEMENT in Service Manual. INSTALLATION Upper Housing Switches 1. For HORN and START switch caps, release torsion spring leg from hole in switch cap tab. Take note of how the spring is installed. The other leg of the spring can remain in the switch bracket hole. 2. See Figure 1 and Figure 5. Carefully pry stock black switch cap up off the splined actuator shaft (2) on left side of switch. -J02633 1 of 5 5 2 1 1 3 4 is 01405 1. Switch cap installed correctly 2. Switch cap removal from splined shaft 3. Switch cap removal from pivot pin 4. Switch cap installation onto pivot pin 5. Switch cap installation onto spined shaft Figure 1. Switch Cap Removal and Replacement 3. Pry the switch cap up and away from pivot pin (3) on right side of switch, and remove cap. NOTE Use the clear protective cover film to protect the chrome surface of the switch caps during installation. Remove the film after the installation is complete. 4. See Figure 5. Select proper chrome replacement switch cap from kit. 5. See Figure 1. Place cap onto switch, angling the hole on right side over pivot pin (4) on switch. 6. Carefully press switch cap down onto splined actuator shaft (5), rocking and moving the cap until shaft snaps into place in splined hole. 7. For HORN and START switch caps, insert torsion spring leg into hole in switch cap tab. 8. Toggle switch back and forth, checking for proper opera- tion. Turn Signal Switches 1. See Figure 1 and Figure 5. Carefully pry stock black switch cap up off the splined actuator shaft (2) on switch. 2. Pry the switch cap up and away from pivot pin (3) on switch, and remove cap. 3. Select proper chrome replacement switch cap from kit. Peel a clear protective installation cover from the sheet and place it over the surface of the cap. 4. See Figure 1. Place cap onto switch, angling the hole on top over pivot pin (4) on switch. 5. Carefully press switch cap onto splined actuator shaft (5), rocking and moving the cap until shaft snaps into place in splined hole. 6. Toggle switch back and forth, checking for proper opera- tion.

Incoming search terms:

HARLEY DAVIDSON VRSC FUEL TANK SIDE COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
INSTALLATION 1. Note the left and right areas on frame where the covers will be installed. Using a 50/50 mixture of isopropyl alcohol and water, thoroughly clean the frame tubes surrounding the fuel cell on the left and right sides. Let dry completely. 2. Unlock and open seat. NOTE Loosening the ignition/light switch screw (in the following step) will allow much easier alignment of the ignition/light switch cover and ignition/light switch during installation. 3. See Figure 1. At area inside of frame rail just above the ignition/light switch housing, loosen the ignition/light switch screw just enough to allow the ignition/switch switch to move slightly from side to side and up and down. Do not completely remove screw 4. See Figure 4. Obtain the right side cover bracket (ignition/light switch side) from kit. 5. Remove the strips protecting the adhesive at all of the raised sections on the cover. 1 2 is 02045 1. Ignition/Light Switch Screw 2. Ignition/Light Switch Figure 1. Loosen Ignition Switch Assembly 6. See Figure 2. Carefully align the right side cover between the three frame tubes. Beginning with the left portion of the cover, press the cover between the upper and lower frame tubes until the raised portions of cover (with adhesive) begin to snap into place. While carefully aligning the right portion of the cover, move the ignition/light switch as necessary until centered within hole in cover, then firmly press into place. Adjust ignition/light switch until the switch is centered within cover. Make sure all raised locations (with adhesive) are firmly contacting the upper and lower frame tubes and that cushion rests against front vertical frame tube. 7. See Figure 1. Tighten the ignition switch screw to 6-10 Nm (53-88 in-lbs ) . NOTE The right side (ignition/light) switch cover surface can be damaged by the key fob (from vibration) when the key is in the ignition and the bike is running. You can either remove the key fob so it does not damage the cover surface, or you can install the plastic clear sheet (included in kit) onto the side cover for protection. 8. If desired, perform the following to install the plastic clear cover onto the ignition/light switch cover. a. Obtain the plastic (rhino) sheet and hold up to the switch cover to determine proper orientation and spacing. b. Carefully peel the adhesive backing from the plastic sheet and position onto the cover. Use a wet sponge, and working out from the center, rub out any bubbles or overlapped areas under the sheet. Allow to dry completely.

Incoming search terms:

2000-2010 KTM X2 SWITCH WIRING HARNESS Removal and Installation Manual

0

Filed Under (KTM) by admin on 25-01-2012

download
The included 3600-SWHA switch harness is intended for use with offroad models that do not come with a Hi/Low beam switch from the factory. The harness is compatable with stock AC lighting electrical systems as well as high output DC electrical systems. 1. Remove the stock numberplate or headlight. Remove the stock kill switch from handlebars and replace with the 3600-SWHA switch. 2. Remove the gas tank. Route the white and black leads from the 3600-SWHA under the tank following the wires from the stock kill switch. Disconnect the stock kill switch bullet and connect the white wire of the 3600-SWHA to the wiring harness. Disconnect the stock kill switch ring terminal and connect the ring terminal of the 3600-SWHA. Fully remove the stock kill switch. Be sure all the wires are safe from being burned or pinched and re-install the gas tank. 3. Disconnect the two female spade terminals from the stock headlight switch (if present). Connect the terminal with the yellow wire to the red power lead from the switch. Connect the white wire to the blue accessory output from the switch. Be sure the clear silicone sleeves are covering the stock plastic housings. 4. Connect the X2 headlight to the switch headlight plug. Note: The stock headlight plug will not be used for the X2 installation, but is still functional for connecting the stock headlight. The stock plug will turn on and off with the new headlight switch, and will be powered in either of the Low or High Beam positions

Incoming search terms:

2008 SUZUKI GSX 1300 RK IGNITION SWITCH INSPECTION/ REPLACEMENT

0

Filed Under (Suzuki) by admin on 29-11-2010

download
INSPECT ROUTING 1. Remove the upper and lower meter panels (refer to Service Manual page 9D-15). 2. Check if the ignition switch lead wire is clamped and routed correctly. Incorrect positions are shown in Figures 1 and 2. Correct routing and clamping is shown in Figures 3 and 4 on page 5. REROUTING 1. Reroute the ignition switch lead wire correctly (Figure 3 and Figure 4). The ignition switch lead wire should not be covered by the other wire harnesses. 2. Turn the handlebars back and forth to verify that the steering operates smoothly and the wiring harness does not become kinked or pinched. 3. Proceed to PUNCH MARK AT VIN on page 8. from the motorcycle (refer to Service Manual page 1H-12). Remove the two black plastic covers to access the cylinder cap mounting bolts (Figure 5). Note: The black plastic covers will not be reused. Secure the mount area (bottom) of the ignition switch in a vise (Figure 6). NOTE: Turn the ignition switch to the OFF position and remove the key from the ignition switch before disassembling the switch. Remove the two “break-off” screws from the ignition switch using the special screwdriver. Set the stepped end of the sleeve on the special screwdriver facing toward the “break-off” screws (Figure 7). Strike the special screwdriver 5 to 7 times with a hammer to produce a deep enough groove on the screw head for the screwdriver to work properly (Figure 6). Pay attention not to hit other parts with the hammer. Turn to remove the “break-off” screws in a counterclockwise direction. If the groove becomes damaged, make another groove at a 90o angle to the original groove. Remove the ignition switch from the vise and hold it upright over the workbench and carefully remove the cylinder cap (Figure 8). NOTE: Pay close attention to the order and orientation of the ignition switch parts during disassembly. REPLACEMENT OF IGNITION SWITCH (Customer Sold Units/Dealer Demo Units- Only If Inspection Shows Incorrect Routing And Unit Has Been Ridden) New Ignition Switch Disassembly 2.

YAMAHA FZR 400 ELECTRICAL CIRCUIT DIAGRAM

0

Filed Under (Yamaha) by admin on 29-11-2010

download
CHECKING OF SWITCHES Check the switches for the continuity between the terminals to determine correct connection. Read the following for switch inspection. SWITCH CONNECTION AS SHOWN IN MANUAL The manual contains a connection chart as shown left showing the terminal connections of the switches (e.g., main switch, handlebar switch, brake switch, lighting switch, etc.) The extreme left column indicates the switch positions and the top line indicates the colors of leads connected with the terminals in the switch component. “C’&-0″ indicates the terminals between which there is a continuity of electricity; i.e., a cl.osed circuit at the respective switch positions. In this chart: “R and Br” and “L/W and L/R” are continuous with the “ON” switch position. “B and B/W” is continuous with the “OFF” switch position. “B and B/W” is continuous with the “LOCK” switch position. “B and B/W” and “R and L/R” are continuous with the “P” switch position. CHECKING SWITCH FOR TERMINAL CONNECTION Before checking the switch, refer to the connection chart as shown above and check for the correct terminal connection (closed circuit) by the color combination. To explain how to check the switch, the main switch is taken for example in the following

Incoming search terms:

Honda Goldwing GL1800 Solid Rear Axle Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Specifications Overall Width: 57.75″ Overall Length: 108″ Overall Length w/EZ-Steer 109.5 Wheel Base: 71″ Extended 4.5″ At Rear Axel Wheel Base w/EZ Steer 72.5″ Load Capacity: 500 Lb Tire Size: 205 / 70 / R15 Wheel Size (15″) Offset +35 mm 15x7JJ 4×4.5 Tire Pressure 20 PSI Suspension: “Zero-Flex” Internal Swing Arm utilizing 3 shocks, OEM shock absorber plus 2 coil over shock absorbers. Rear Differential: Champion Lightweight rear axle / differential assembly. Gear Ratio 2.93:1 gear ratio Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 6.75 cubic feet. 3 full-face helmets and additional storage. Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 7 of 28 Revision 10 4 Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. • Seat (to be re-installed without modification) • Left and right side covers (to be re-installed without modification) • Battery and battery box (to be re-installed without modification) • Left and right saddle bags • Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) • Trunk (to be re-installed without modification) • Left and right passenger foot rests (to be re-installed without modification) • Left and right foot rest under covers (to be modified and re-installed) • Left and right rear crash bars • Saddle bag trunk stay (to be modified and re-installed) • Left and right mufflers (Mufflers only, do not remove decorative covers) • Rear wheel • Left and right pivot bolt covers (to be re-installed without modification) • Reverse resistor (to be relocated) • Swing Arm – Note : Carry out brake system modifications (Section 5) prior to removing Swing Arm. • Note : Upper bolt of mono shock can be removed without removing the fuel tank. • Note : Do not remove actuator hose from actuator pump or shock absorber. Dismounting shock actuator pump will allow more movement of shock absorber when removing swing arm.Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 8 of 28 Revision 10 5 Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm. From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Sidecars Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Sidecars Trike Conversion Kit.

Incoming search terms:

BMW R 1200 RT-P Supplementary Instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
Switch Layout – Left The left handlebar switch contains the standard operating controls for the police motor. The horn switch also operates the siren air horn when the ignition is turned “On”. A supplementary switch holder is standard, containing two switch blank plugs A & B. These locations are reserved for options such as Cruise Lights, Radio Rebroadcast, Radio Speaker “off” or other desired optional rocker switches. Siren Switch: The BMW/Code 3 siren is operated by one momentary push button switch, but only when the ignition is “on”. Pressing the button engages the siren into wail tone. Each subsequent press of the button advances to yelp, then hyper-yelp, then back to wail (California models only have wail and yelp). Press and hold to turn-off siren at any time. The siren has been programmed to accept a push of the button similar to clicking a computer mouse. This was done to avoid accidentally activating siren by nudging the button. A quick, clean press or “poke” of the button provides crisp activation. Switch Layout – Right The right handlebar switch contains the standard operating controls for the police motor including starter button. However, the additional switch functions are as follows: (A) Emergency Lights: This three-position switch controls the switching power to all emergency lights. Rocking the switch down to the middle position engages rear channel for the emergency lights (remember switch (C) must be down), rocking switch (A) down further engages front and rear channels – all emergency lights (adding front and side lights). With the switch in this position, rocking switch (C) up will cancel rear lights, but keep front and side lights operating. An LED indicator display can be seen through the back of the right front LED emergency light housing, showing whether the rear or front and rear emergency light channels are switched “on

2001 YAMAHA TDM900 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 20-11-2010

download
CHECKING THE SWITCHES ELEC EAS00731 ELECTRICAL CHECKING THE SWITCHES Check each switch for damage or wear, proper connections, and also for continuity between the terminals. Refer to “CHECKING SWITCH CONTINUITY”. Damage/wear Repair or replace. Improperly connected Properly connect. Incorrect continuity reading Replace the switch. -3- ELECTRIC STARTING SYSTEM ELEC EAS00755 ELECTRIC STARTING SYSTEM CIRCUIT DIAGRAM -4- ELECTRIC STARTING SYSTEM ELEC 4 Main fuse 5 Battery 7 Starter relay 8 Starter motor 9 Main switch 12 Starting circuit cut-off relay 13 Sidestand switch 14 Neutral switch 49 Clutch switch 59 Engine stop switch 60 Start switch 61 Ignition fuse -5- ELECTRIC STARTING SYSTEM ELEC EAS00756 STARTING CIRCUIT CUT-OFF SYSTEM OPERATION If the engine stop switch is set to “” and the main switch is set to “ON” (both switches are closed), the starter motor can only operate if at least one of the following conditions is met: The transmission is in neutral (the neutral switch is closed). The clutch lever is pulled to the handlebar (the clutch switch is closed) and the side- stand is up (the sidestand switch is closed). The starting circuit cut-off relay prevents the starter motor from operating when neither of these conditions has been met. In this instance, the starting circuit cut-off relay is open so current cannot reach the starter motor. When at least one of the above conditions has been met the starting circuit cut-off relay is closed and the engine can be started by pressing the starter switch. WHEN THE TRANSMISSION IS IN NEUTRAL WHEN THE SIDESTAND IS UP AND THE CLUTCH LEVER IS PULLED TO THE HANDLEBAR 4. Starting circuit cut-off relay Disconnect the starting circuit cut-off relay from the wire harness. Connect the pocket tester (Ω 1) and battery (12 V) to the starting circuit cut-off relay terminals as shown. YES NO Replace the starting circuit cut-off relay. Does the starting circuit cut-off relay have continuity between blue/white and black? EAS00759 Continuity Tester positive probe sky blue Tester negative probe blue/yellow No conti- nuity 1 2 1 3 Tester positive probe sky blue Tester negative probe black/yellow Battery positive terminal red/black Battery negative terminal black/yellow 1 2 Tester positive prove blue/white Tester negative prove black 3 4 5. Starting circuit cut-off relay (diode) Disconnect the starting circuit cut-off relay from the wire harness. Connect the pocket tester (Ω 1) to the starting circuit cut-off relay terminals as shown. Measure the starting circuit cut-off relay for continuity as follows. Tester positive probe blue/green Tester negative probe blue/yellow 4 3 Tester positive probe black/yellow Tester negative probe sky blue 2 1 Tester positive probe blue/yellow Tester negative probe sky blue 3 1 Tester positive probe blue/yellow Tester negative probe blue/green 3 4 When you switch the tester’s positive and negative probes, the readings in the above chart will be reversed. Are the testing readings correct? YES NO Replace the starting circuit cut-off relay. NOTE: EAS00760

Incoming search terms:

2001 HONDA CRF 230 Dual Sport Kit Installation Manual

0

Filed Under (Honda) by admin on 21-11-2010

download
1. Remove the seat, fuel tank, side panels, and front number plate. 2. Taillight and Turn signal Installation: Note that Baja Designs has updated this kit to use the new style LED taillight. The mounting is the same. Mount the rear taillight assembly to the rear fender as shown in Photos 1 and 2. Transfer drill the mounting holes in the taillight assembly into the fender and mount using the countersunk fasteners provided. The tail light lens should just line up with the end of the fender. Mount the turn signals into the side of the taillight assembly as shown in Photos 1, 2 and 3. The taillight has not been pre-drilled to allow placement of the turnsignals to be varied to accommodate different exhausts. Use a 3/8″ drill for the turn signal mounting hole 3 Photo 3 Photo 2 Photo 1
. 3. Brakelight Switch Installation: This is a tight fit on the CRF230 – take your time and it’ll work. Drill a 1/8″ hole in the brake lever 4 ½” from the center of the brake pedal pivot point (Photo4). 4 Photo 5 Drill 1/8″ hole here Photo 4 Install the brake-switch bracket under the right case bolt directly above the oil filler cap (Photo 5). Attach the spring to the hole you drilled in the pedal. Adjust the switch in the bracket so it engages about halfway through the pedal throw. You may need to lengthen (stretch) the spring slightly to allow proper switch adjustment. Turn-Signal Switch Installation: Install the turn signal switch on the handlebar next to the grip as shown in Photo 6 . The switch has a single screw that pinches it together on one side. Two tabs secure the switch halves on the other side. Remove the screw to separate the halves so that it can be installed on the handlebar. When installing the switch to the handlebar, make sure the tabs are seated in their locating holes and then tighten the pinch screw. DO NOT OVER TIGHTEN THIS SCREW, as too much force can strip the body of the switch. The clutch perch may have to be moved inward slightly to make room for the switch. Run the wires along the bottom of the handle

Incoming search terms:

The Honda VTX 1300 Keyless Ignition Switch Installation instructions

0

Filed Under (Honda) by admin on 04-11-2011

download
Remove the seat from the motorcycle.2. Lift the ignition module off of the battery cover and let it drape over the side of the motorcycle. 3. Remove the battery cover and disconnect the negative battery cable. 4. Remove the gas tank and set it aside. There is a vent line at the right rear of the tank, a vacuum line and the gas feed line on the left side of the tank at the petcock, and two speedometer connectors at the left front of the gas tank. 5. Remove the clip from the top of the steering head cover and remove the right hand side cover. See picture at right. 6. Remove the headlight to expose the wiring connectors inside the headlight shell. 7. Remove the left-hand side cover. On the left side of the frame is an electrical wire shroud wire tied to the left side of the frame with a reusable wire tie. Inside this cover is the 3-pin connector that connects the ignition switch to the bike’s wiring harness. Pull the small lever back to release the wire tie and remove the wire tie. Pull back the wire shroud to reveal the wire connectors inside. Disconnect the 3-pin connector that comes from the ignition switch. Remove the two bolts holding the ignition switch to the bike’s frame. See Picture at right. Remove the ignition switch from the bike. You may have to remove the connector body from the ignition switch wires to slide the wires through the frame when removing the ignition switch. You may now reinstall the side cover. 8. Lay the new wiring harness along the backbone of the bike with the two 9-pin connectors at the headlight and the 6-pin and 3-pin connectors at the battery. Insert the two 9-pin connectors through the large hole in the back of the headlight shell. Inside the headlight shell is a red 9-pin connector. Disconnect this red 9-pin connector and insert the new wiring harness connecting each side to the red 9-pin connectors. See picture at right

Incoming search terms:

Incoming search terms: