how do i align the front end on kawasaki mule

You search Auto repair manual PDF how do i align the front end on kawasaki mule, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how do i align the front end on kawasaki mule Direct Download speed 5282 Kb/s

  how do i align the front end on kawasaki mule Full Version speed 6162 Kb/s



Kawasaki Mule Lift Kit Installation Manual

0

Filed Under (Kawasaki) by admin on 04-05-2012

download
Front Lift Installation 1. Ensuring that the parking brake is set, place jack under center of the Mule front end and lift until front wheels clear the ground. Be careful to support Mule properly so that it is secure, but so that the A-arms and struts can droop to full extension. 2. Remove front wheels. 3. If applicable, remove the heater to allow access to the strut mount behind the heater coil. Heater 4. Starting with the left side (driver side), remove the cotter pin and castle nut that secures the strut to the strut mount. Castle Nut & Pen 5. Push bolt through the bolthole, taking care not to damage the brake line that is attached to the bolt. If you are having difficulty removing the bolt, you may have to remove the brake lines that are attached to the front brakes. In this case refer to owners manual for removing brake lines. Screwdriver NOTE: Keep in mind that if you remove the brake lines you must bleed your brakes according to operator’s manual. 6. Once the bottom of the strut has been loosened, then unbolt the top of the strut. The nuts securing the top strut can be located in the dash of the Mule on the left and right sides. In most cases these nuts are easily accessible, but you may have to remove the glove box or heater coils, depending on the model and options purchased with the Mule.

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE STREET PERFORMANCE TOURING END CAP MUFFLER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-04-2011

download
PRODUCT INFORMATION Noise Emission Warranty Harley-Davidson warrants that these mufflers, at the time of sale, meet all applicable United States E.P.A. Federal noise and Emissions standards. This warranty extends to the first person who buys these mufflers for proposes other than resale, and to all subsequent buyers. Warranty claims should be directed to an authorized Harley-Davidson Dealer. Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances. INSTALLATION NOTE Install end caps on mufflers before installing mufflers on vehicle. Install Direct Bolt-On End Caps 1. See Figure 1. Install end cap (2) to muffler (3) with four socket head cap screws (1). Tighten to 82-86 in-lbs (9.3- 9.7 Nm) . 2. Repeat for opposite side muffler. 3 2 1 is05426 1. Socket head screw (4) 2. End cap 3. Muffler Figure 1. Install End Cap on Muffler Install Attachment Ring End Caps 1. See Figure 2. Slide the three U-nuts (2) onto the bosses of the end cap attachment ring cup on the muffler. 2. Install attachment ring (1) to muffler with four socket head cap screws (3). Locate the attachment ring with a U-nut in the 12 o’clock position. Tighten to 82-86 in-lbs (9.3-9.7 Nm) . 3. Slide end cap (5) onto muffler body being careful to align holes in end cap with U-nuts. 4. Install the three countersunk screws (4) and tighten screws securely. 5. Repeat for opposite side muffler

Incoming search terms:

Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Upgrading the Suspension on the Kawasaki ER6-F/ N

0

Filed Under (Kawasaki) by admin on 30-11-2010

download
Top fork is as removed. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Before removing the fork from the clamps on the yokes I loosened the fork top. Before removing the fork top the fork-slider was placed in a vice and the bottom bolt loosened….. … before finally being removed with the fork upside down. Because the springs were still in situ this gave sufficient tension on the damper-rod to prevent it from turning and allow the bolt to be removed. When I turned the fork the right-way up to remove the fork-top I did it over a container to catch the oil. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource All the OE components that will no longer be required. Left to right. Fork-top, spacer tube, washer, spring, damper-rod. Bottom bolts get re-used. Old and new, laid-out for comparison. The damper unit, minus spring and fork-top, drops inside the stanchion and slider. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Then the bolt goes back in, as tight as possible, to secure it. Top fork is done, second one awaits. Note the spring seat on the right, just below the spring. This drops over the damping rod after the oil has been added. The small locking-nut screws over the threaded part of the damping-rod next, all the way to the bottom. Spring drops in and then the fork-top screws on to the damping-rod as well, all the way down to the lock-nut which is used to secure it. At this point the stanchion is extended to the fork-top which is screwed in. Job done.

Incoming search terms:

HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

Kawasaki Exhausts – ZX-6 ZX-10 Zx-14 Exhaust – Slip-ons INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Our favorite exhaust options for Kawasaki ZX Ninjas – ZX-10,ZX-6r, and the new horsepower king, Zx-14.. Grab your horsepower today. We love Rob Muzzy and Muzzy Exhausts.Going back to Doug Chandler and Scott Russell, Muzzy has been synonomous with Kawasaki and performance – and for years, if you rode Kawasaki,and you were on the podium, Muzzy was on your exhaust. We also feature Arrow and Yoshimura exhausts for your ZX-6R, ZX-10 and ZX-14. We love the sound of a Yosh exhaust on any Kawasaki Ninja. Yoshimura Oval (RS-3) Race Slip-On for Kawasaki ZX14R 2006 The easiest and least expensive way to experience Yoshimura performance is with our Slip-On/Bolt-On lines. Bolt-On style bolts to the O. E. M. mid-pipe Slip-On style with its stainless steel easily attaches to the mid-pipe RS-1 is available where noted Usually, no jetting or re-programming is required and installation is a snap Hindle Stainless Exhaust High Head Pipes – Kawasaki ZX6R-RR 03-04 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo North Denver News http://northdenvernews.com Powered by Joomla! Generated: 19 October, 2010, 12:28 Hindle Stainless Exhaust Low Head Pipes – Kawasaki ZX9R 00-03 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo

Kawasaki Mule Roof 600, 610 and 4010 Trans Crew, Roof Installation Manual

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
INSTALLTION INSTRUCTIONS – Mule 600/610 (4010 Trans skip to pg 4) 1. Place Roof Panel on top of UTV Roll cage and center front to back, and left to right. 2. Using Figure 1 Below – place UTV Roof Mounting Brackets around roll cage bar and using a marker, mark the position of the holes needed in the roof for each Roof Mounting bracket . Figure 1 Copyright 2007 DiamondBack Automotive Accessories, Inc. Page 3 3. Next, remove the roof from the roll cage and using a drill with 1/4″ bit, drill holes using the marks as a guide. 4. Cut (4) 3″ strips of adhesive foam and apply to roof in where mounting brackets are positioned to prevent roof rattling once mounted. Foam should run in the direction of the roll cage as shown in Figure 1 above. 5. Next, reposition the roof on the roll cage according to step 1. 6. Prior to attaching the roof mount brackets, cut the remaining adhesive foam in half and apply one section to the roof in the center of the roof where roof and each roll cage bar meet as shown in Figures 1 above. If additional tape is required to prevent rattling it can be purchased from any hardware store as window sealant foam tape. 7. Next, attach the roof mount brackets according to Figure 2. Use channel locks or pliers to hold top of carriage bolt and turn nut with 7/16″ socket.

Incoming search terms:

Kawasaki MULE 600 / 610 SNOW PLOW INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. PRELIMINARY: 1.1 Remove the six 6 mm. screws and plastic skid / splash shield from the bottom front of the vehicle frame. (These bolts and plastic skid / splash shield will not be reused snow plow mounting frame installed onto the vehicle.) 1.2 If the vehicle has the Kawasaki optional brush guard installed, it will have to be removed and then reinstalled after the snow plow mounting frame is installed. (The brush guard will fit with the snow plow mounting frame installed first.) 2. VEHICLE MOUNTING FRAME 2.1 Position the vehicle mounting frame (13) under the front of the vehicle so that the six holes (with pipe spacers) line up with the six 6 mm. threaded holes that the plastic skid / splash shield was attached with and the upper plate is through the large oval hole in the vehicle plastic fascia. Fasten loosely using 6mm. x 1.0mm. x 30mm. bolts (33) , 6mm. lock washers (35) and 6mm. flat washers (34). 2.2 Place a 5/16″-18 “U” bolt (36) around the front cross tube behind the plastic fascia and through each set of holes in the flange of the upper plate of the vehicle mounting frame (total of two “U” bolts). Fasten loosely using 5/16″flat washers (41), 5/16″ lock washers (40), and 5/16″-18 nuts (42). 2.3 Install a 5/16″-18 “U” bolt (36) around the lower frame tubes and through each set of slotted holes in the lower plate of the vehicle mounting frame (total of four “U” bolts). Fasten loosely using 5/16″ flat washers (41), 5/16″ lock washers (40), and 5/16″-18 nuts (42). 2.4 Tighten all the fasteners holding the vehicle mounting frame to the vehicle starting with the 6mm. bolts

Kawasaki ZX-9R Ninja Installation Instructions

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
1. Remove the lower fairing. Remove thelower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide access to the exhaust nuts (flange nuts). Remove the oil cooler mounting bolts and pivot the oil cooler forward to provide access. 2. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 3. Inspect the exhaust gaskets. Replace if necessary. 4. Assemble the head pipes 1 (blue), 2 (red), 3 (yellow), and 4 (green) by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 5. 2000 through 2002 models ONLY!!! Place a billet aluminum exhaust port centering flange Z on each TiForce headpipe -see figure 3 for details. 6. Attachthe assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remaining steps. Reuse the flange nuts saved from step 2 above. Make sure the ends of the headpipes fit flush and snug in the ports and centering flanges Z before tightening (’00-’02 ONLY). 7. Install the S-Bend to the front section of the headpipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications -make sure the headpipes and flanges Z are centered in each port (’00-’02 ONLY!!! ) . 9. Slide the TiForce end can into place. 10. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. See figure 1. 11. Place the bands approximately 108 mm from the edge of the end can. See figure 2. 12. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the headpipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 15. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (refer to step 11 /figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTIONWHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 16. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 17. Go back and reinstall the radiator and oil cooler as per factory specifications. Verify fluid levels as needed. 18. Checkthat all hardware is properly tightened, then start the motor and check for exhaust leaks. 19. Reinstall the fairing and tighten any fasteners per factory specification

Kawasaki ZRX-1100 / 1200 exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 2. Inspect the exhaust gaskets. Replace if necessary. 3. Attach the head pipes 1, 2, 3 , and 4 to the exhaust ports of their respective cylinders, using the flange nuts saved from step 1 above. Loosely apply the flange nuts for now, allowing for ome adjustment. 4. Attach the Y-pipe collectors to the head pipes. Please note that one collector goes to pipes #1 and #4 and one collector goes to pipes #2 and #3 (collectors are labeled). Make sure the ends of the head pipes fit flush and snug in the ports. Do not install the springs at this time. 5. Install the S-Bend to the rear of the two Y-pipe collectors. Do not install the springs at this time. 6. Go back and retighten the head pipe flange nuts per factory specifications – make sure the head pipes are centered in each port. 7. Slide the TiForce end can into place on the S-bend pipe. 8. Loosely attach the two rubber bands, stainless steel bands K, and the stay / hanger G, to the end can using the supplied 6mm hardware H. (See figure 1) . Make sure that the rubber bands fully cover the stainless bands to prevent scratches to the can. 9. Place the bands approximately 108mm from the edge of the end can. (See figure 2) . 10. Go back and tighten the exhaust flange nuts per factory specification. Do not over tighten. 11. Using the stock provided mounting point on the right passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 12. Attach the supplied springs to all the joints, starting from the head pipes and working back to the end can. 13. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 14. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (refer to step 11 / figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 15. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 16. Check that all hardware is properly tightened, and then start the motor and check for exhaust leaks

Incoming search terms:

Kawasaki ZX-9R Ninja TiForce exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 07-05-2012

download
1. Remove the lower fairing. Remove thelower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide access to the exhaust nuts (flange nuts). Remove the oil cooler mounting bolts and pivot the oil cooler forward to provide access. 2. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 3. Inspect the exhaust gaskets. Replace if necessary. 4. Assemble the head pipes 1 (blue), 2 (red), 3 (yellow), and 4 (green) by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 5. 2000 through 2002 models ONLY!!! Place a billet aluminum exhaust port centering flange Z on each TiForce headpipe -see figure 3 for details. 6. Attachthe assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remaining steps. Reuse the flange nuts saved from step 2 above. Make sure the ends of the headpipes fit flush and snug in the ports and centering flanges Z before tightening (’00-’02 ONLY). 7. Install the S-Bend to the front section of the headpipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications -make sure the headpipes and flanges Z are centered in each port (’00-’02 ONLY!!! ) . 9. Slide the TiForce end can into place. 10. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. See figure 1. 11. Place the bands approximately 108 mm from the edge of the end can. See figure 2. 12. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the headpipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 15. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (refer to step 11 /figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTIONWHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN.

Incoming search terms:

Incoming search terms: