how do you replace choke on 2001 foreman es

You search Auto repair manual PDF how do you replace choke on 2001 foreman es, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how do you replace choke on 2001 foreman es Direct Download speed 5282 Kb/s

  how do you replace choke on 2001 foreman es Full Version speed 6162 Kb/s



Lilac LS-18 Motorcycle Maintenance Standards

0

Filed Under (Lilac) by admin on 25-11-2010

download
CYLINDER AND CYLINDER HEAD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Cylinder Bore 54 -0.01 54.1 Boring After boring honing should be performed Ovality 0.01 0.05 Boring After boring honing should be performed Taper 0.01 0.05 Boring After boring honing should be performed Oversize 0.25 steps 55 max. Do R and L cylinders at same time / 4 steps Valve Seat Width 0.8 – 1.0 1.3 Adjust Use a cutter Angle 45∞ Combustion Chamber Volume 18.2cc -0.5cc Remove carbon if heavy accumulation Compression Ratio 7.8:1 Head Gasket Thickness 1.0 Cylinder Head Nut Torque 3.0 kg/m (22 ft.-lb.) Out standard Adjust 8mm nut Intake and Exhaust Ports Port Wall SurfaceMust be smooth Remove carbon Intake and Exh. Valve GuidesOD 12 +0.09 +0.1 ID 7 +0.01 -0.0 7.06 Exchange Intake Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Exhaust Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Intake and Exhaust Valve Seat Face Width Range 0.8~1.0 1.3 Use valve seat cutter Intake Valve Guide Clearance 0.02~0.04 0.08 Replace valve or guide Exhaust Valve Guide Clearance 0.06~0.08 0.12 Replace valve or guide Valve Spring (Large) Installed Load 10.2 kg 8.7 kg Replace Fitted length 31.5 Free Length 36.5 34.7 Replace Tilt 1.5/100 3/100 Replace Valve Spring (Small) Installed Load 5.48 kg 4.65 kg Replace Fitted length 29.5 Page 4 of 10 Free Length 33.5 31.8 Replace Tilt 1.5/100 3/100 Replace Rocker Arm ID 12 +0.00 +0.02112.07 Replace Rocker Shaft OD 12 -0.06 -0.024 11.92 Replace Arm and Shaft Clearance 0.045~0.006 0.10 Replace arm or shaft Tappet Clearance 0.05 Out standard Adjust Measure cold at TDC Rocker Arm Ball Surface 1.8îR -0.006 -0.024 Replace if severe wear Pushrod Bend 0.1 0.5 Straighten Over 100mm (2) CRANKSHAFT, PISTON AND CONROD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Piston OD @ Top 53.65 -0.02 Max Diameter 53.95 -0.015 53.85 Replace Ovality 0.1 Piston and Cylinder Clearance 0.04~0.05 0.15 Replace Piston Ring Groove Clearance 0.03~0.07 0.10 Replace Piston Oversize Step 0.25 4 steps Top Ring and 2nd Ring Thickness 2 -0.01 -0.03 1.92 Replace Width 2.5 -0.01 0.55kg Tension 0.85 – 1.15kg 1 Replace End Gap 0.15 – 0.35 Replace Oil Ring Thickness 3.2 -0.01 -0.03 3.12 Replace Width 2.5 -0.1 Tension 1.0~1.3kg 0.65kg Replace End Gap 0.15~0.35 1 Replace Ring Gap Position 120∞ 3 equal spacesOut standard Adjust Avoid Piston Pin Axis Ring Oversizes 0.25 steps 4 steps Piston Pin OD 15 -0.0 +0.006 14.95 Replace Pin Hole in Piston ID 15 +0.012 -0.015.05 Replace Pin and Piston Clearance -0.006 ~ +0.012 0.06 Replace Hand push fit piston at 100∞C Conrod Small End Bush ID 15+0.027+0.016 15.07 Replace bush Conrod and Piston Pin Clearance 0.01~0.027 0.07 Replace Crankpin OD 24.94 +0.0+0.0124.90 Replace Crankpin Roller OD 5 (+0.001+0.003) Refer to conrod ID Replace 3Sizes; 52 per assembly for selective fit 5 (+0.0 -0.002) 5 (-0.003 -0.005) Conrod ID 34.95+0.03+0.02435.02 Axial Play 0.2~0.4 0.5 Adjust Radial Play 0.026~0.036 0.06 Replace

Incoming search terms:

1999 Toyota Camry LE V6 Body and Interior Maintenance Record

0

Filed Under (Toyota Manuals) by admin on 03-10-2011

download
Action Date Mileage Day Cost (with tax) By Interval Notes Oil and Oil Filter Change 8/30/1999 2494 Monday$77.97 Dealer 2494Non-synthetic 5w-30 (Toyota dealer stock) Oil and Oil Filter Change 10/31/1999 5484 Sunday $30 Owner 2988.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 12/30/1999 8460 Thursday$30 Owner 2975.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/21/2000 11414 Monday $30 Owner 2953.3Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 4/22/2000 14479 Saturday$30 Owner 3065.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 7/4/2000 17339 Tuesday$30 Owner 2860.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 7/4/2000 17339 Tuesday$15 Owner 17339Purolator A24690 Air Filter Oil and Oil Filter Change 9/16/2000 20161 Saturday$30 Owner 2821.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Drain and Fill 10/27/2000 21913 Saturday$15 Owner 21913Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Transmission Drain and Fill 10/28/2000 21920 Sunday $15 Owner 7Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Oil and Oil Filter Change 11/19/2000 23066 Sunday $30 Owner 2904.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/11/2001 26062 Sunday $30 Owner 2996.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Flush 4/30/2001 28351 Monday$135 Dealer 2835113 Quarts Mobil 1 Dexron III Synthetic ATF – TransTech Flush Tires – Rotate 5/12/2001 28766 Saturday$0 Dealer 28766Tires – Rotate Coolant Flush 5/12/2001 28766 Saturday$112 Dealer 28766Toyota Red Coolant + MOC Flush (Extended warranty with service) Oil and Oil Filter Change 5/13/2001 28793 Sunday $30 Owner 2730.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 5/13/2001 28793 Sunday $15 Owner 11454Purolator A24690 Air Filter PCV Valve – Replace 5/26/2001 31083 Saturday$10 Owner 31083Toyota OEM PCV Valve Windshield Wipers – Replace 5/26/2001 31083 Saturday$10 Owner 31083Windshield Wipers – Replace Oil and Oil Filter Change 5/27/2001 31296 Monday $30 Owner 2502.8Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 9/15/2001 34374 Saturday$30 Owner 3078.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Tires – Replace 9/28/2001 34784 Friday$431.23 Dealer 34784 (4) Bridgestone RE950 Tires (2 of original tires had tread separation – ~30% tread remaining) Oil and Oil Filter Change 11/12/2001 37365 Monday $30 Owner

Incoming search terms:

TOYOTA NEW SEAT BELT TONGUE PLATE STOPPER SERVICE PARTS

0

Filed Under (Toyota Manuals) by admin on 10-10-2011

download
installation procedures are provided to supplement the Repair Manual. MODEL YEAR Avalon 1995 – 2001 Camry 1983 – 2001 Corolla 1980 – 2001 Camry Solara 1999 – 2001 Sienna (Front Seat Belt Only) 1998 – 2001 RAV4 1997 – 2001 4Runner 1992 – 2001 Land Cruiser 1991 – 2001 Tundra 2000 – 2001 Tacoma 1997 – 2000 ECHO 2000 – 2001 Celica 1980 – 2001 Prius 2001 – 2001 Tercel 1981 – 1999 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME N/A 73219-02010 Stopper, Tongue Plate (Black)* N/A 73219-02020 Stopper, Tongue Plate (Gray)* N/A 73219-02030 Stopper, Tongue Plate (Beige)* *Use a stopper color that is closest to the seat belt webbing color. OP CODE DESCRIPTION TIME OPN T1 T2 BD0047 Install Seat Belt Tongue Plate Stopper 0.1 73219-020#0 62 12 Applicable Warranty*: This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

Incoming search terms:

BMW F 650 GS Repair Manual And Maintenance schedule

0

Filed Under (BMW) by admin on 19-11-2010

download
Replace oil in telescopic forks Check the coolant and restore to correct level if necessary *) Replace the coolant (every 2 years) every 2years Check valve clearances, adjust if necessary Replace the spark plug Drain the outlet hose from the air filter box Replace intake air filter If motorcycle is operated in very dirty or dusty conditions, clean or replace the intake air filter every 10,000 km (6,000 miles); check every 3,000 km (1,800 miles) Replace fuel filter (every 20,000 km/12,000 miles) 20,000 km Check clutch play, adjust if necessary Check wheel spoke tension and tighten if necessary more frequently if motorcycle is ridden in severe off-road conditions Examine brake pads and discs for wear, replace if necessary *) more frequently if motorcycle is ridden in severe off-road conditions Check brake fluid level at front and rear and top up if necessary *) Check for operation of brake system and freedom from leaks; repair/replace if necessary *) Replace the brake fluid at least once a year Replace the primary front/rear brake master cylinder cup (every 40,000 km/24,000 miles on a motorcycle with ABS ) 40,000 km Check wheel bearings and replace if necessary *) Check or, if necessary, replace chain, sprocket, chain guide rollers and pinion *) more frequently if motorcycle is ridden in severe off-road conditions Check chain tension and adjust if necessary *) Check battery acid level, add distilled water if necessary more frequently if motorcycle is ridden in severe off-road conditions Clean and grease the battery terminals, if necessary Check steering head bearings and adjust *) or replace if necessary *) Grease the side and main stands Grease the brake pedal Check bolts and nuts on engine mountings, frame connections, exhaust system mountings, swinging fork pivot, suspension levers, brake pedal, main and side stands and quick-release axles for tightness Final inspection with road safety and functional check

Harley Davidson 1990 and later HSR Choke Cable Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
The majority of HSR42/45 installations use the Harley cable. Installation is simple when the installation instructions are followed, step by step. Those steps are: • Remove the stock Harley choke cable assembly. • Remove the spring and plunger from the stock cable. • Remove the Mikuni “Starter Nut” from the HSR. • Remove the Mikuni spring and plunger from the HSR. • Install the Mikuni spring and plunger on the Harley choke cable. • Install the Harley choke cable with the fitted Mikuni spring and plunger into the HSR carburetor. • DO NOT use the Mikuni Starter Nut; discard it. • DO NOT use the Harley spring or plunger; discard them. Note: If you do not have installation instructions, you may download them from the www.mikuni.com website in the “manuals” section. If the Mikuni Starter Nut is fitted to the Harley cable, the choke plunger is held off its seat and the choke is open all the time. If the Harley spring and plunger are used, the plunger does not seal and the choke is open all the time. The result, in both cases, is very poor fuel mileage (30 mpg or less). Another possible cause of poor mileage, rough idle and fouled spark plugs is incorrect cable routing. The stock Harley choke cable is very stiff and may not be fully seated in the metal elbow at the carburetor end of its run. This condition is easily corrected. On occasion, one of these errors may have been made by someone else at another location. The unfortunate mechanic who inherits the task of correcting the rich condition, poor idle and poor fuel mileage may have no clue as to the mismatch of parts. For this reason, we include the photos and text to help you discover if your installation is correct.

Incoming search terms:

2001-2002 GL1800 A ABS Speed Sensor Wire Clamp Location INSPECTION/ REPAIR PROCEDURES

0

Filed Under (Honda) by admin on 29-01-2011

download
1. If the VIN is within the preceeding range, inspect the front ABS speed sensor wire clamp according to the following illustrations. 2001-2002 GL1800A ABS Speed Sensor Wire Clamp Location INCORRECT Installation CORRECT Installation Service Bulletin American Honda Motor Co., Inc. 2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location 0112 GL1800 #9*GL1800 #9*0112*2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location*GL1800, ABS Speed Sensor Wire Clamp Location*Motorcycle*1800 2 of 2 ©2001 American Honda Motor Co., Inc. – All Rights Reserved GL1800 #9 DECEMBER 2001 IDENTIFICATION There is no identification mark associated with this Service Bulletin. PARTS INFORMATION There is no parts information associated with this Service Bulletin. WARRANTY INFORMATION The normal warranty claim submission requirements apply. Submit one warranty claim per VIN with the following information only: Inspected and REPAIRED Template: GL#9 Hours: 0.2 hours Parts: None If the clamp is installed correctly on top of the speed sensor, no further action is necessary. 3. If the clamp is installed incorrectly under the speed sensor, remove and reinstall the clamp and speed sensor correctly. Torque the bolts,. Torque: 12 N • m (1.2 kgf • m, 9 lbf • ft) If the speed sensor wire clamp for the front ABS speed sensor is installed incorrectly, the ABS speed sensor air gap may be out of specification. This does not affect ABS speed sensor operation, but the clamp should be installed correctly. Inspect and repair all affected units using the Inspection/Repair procedures listed below. Inspect all unsold units and customer units brought in for service. AFFECTED UNITS 2001-2002 GL1800A units as follows: MODEL 2001 GL1800A All units 2002 GL1800A 1HFSC474*2A100001 – 1HFSC474*2A101643 * = denotes check digit Any unit in the above VIN range may be affected and should be inspected according to the procedures in this Service Bulletin. All units outside of the above VIN range do not require inspection. CUSTOMER NOTIFICATION There is no customer notification associated with this Service Bulletin.

Incoming search terms:

2001 – 2002 GL1800/ GL1800A Rear Tire Inspection

0

Filed Under (Honda) by admin on 27-11-2010

download
1. Inspect the motorcycle for a punch mark as described in Identification on page 2. If a punch mark is present no further action is necessary, return the unit to the customer. 2. Qualify the unit/customer as follows: •Is the tire on the motorcycle the original factory installed tire? •Is the air pressure loss more than three psi per month? Note: Refer to page 145 in the Owner’s Manual. “Even tires that are in good condition may lose one to two psi per month if not checked and adjusted regularly” . If the GL1800 meets the above qualifications, proceed with the repair procedure. 3. Place the motorcycle on a lift and secure it on the centerstand. 4. Remove the rear wheel as described on page 14-9 of the Service Manual. 5. Starting at the valve stem/balance mark area, carefully remove the rear tire from the wheel. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. 6. Carefully inspect the entire circumference of both tire beads. Inspect both the inside and outside of the bead for any distortion or injuries. See examples of injuries below. 2001 – 2002 GL1800/GL1800A Rear Tire Inspection GL1800 #6 OCTOBER 2001 MTB 9430 (0109) CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your Honda. These procedures should not be attempted by “do-ityourselfers,” and you should not assume this bulletin applies to your Honda, or that your Honda has the condition described. To determine whether this information applies, contact an authorized Honda dealer. Service Bulletin American Honda Motor Co., Inc. 2001-2002 GL1800/GL1800A Rear Tire Inspection 0110 GL1800 #6*GL1800 #6*0110*2001-2002 GL1800/GL1800A Rear Tire Inspection*GL1800/GL1800A, Rear Tire Inspection, Bead, Tread*Motorcycle*1800 2 of 4 ©2001 American Honda Motor Co., Inc. – All Rights Reserved GL1800 #6 OCTOBER 2001 Inside BeadInjury Outside BeadInjury Outside BeadInjury 7. Carefully inspect the entire circumference of both tire beads. Inspect both the inside and outside of the bead for any distortion or injuries. See examples of injuries below. 8. If there is no evidence of bead damage, re-install the tire on the rim. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. Be sure to align the balance dot with the valve stem. Inflate the tire to 41 psi. Install the wheel assembly on the motorcycle and proceed to the Identification and then to the Warranty section. 9. If any damage or injury is present replace the tire and valve stem. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. Balance the new tire as necessary

Incoming search terms:

POLINI X1 GENERAL INFORMATION AND SPECIFICATIONS

0

Filed Under (Polini) by admin on 02-12-2010

download
Air cleaner – Clean and reoil daily or after each moto to prevent motor failure and reduced performance. Transmission oil – change after every race, or at end of riding day. Chain – check tension and lubricate before every ride, adjust or replace as needed. Reoil after riding in damp conditions. Clutch – disassemble and clean clutch assembly frequently, every 2-3 races at least. Inspect kickstarter gears at this time. Ignition cover – remove cover and wipe dry after each ride or after washing bike to remove condensation. Piston rings – replace as often as every 3-5 races with expert rider, less often with less aggressive riders. Piston, pin, rod bearing & circlips – replace as often as every 8-10 races with expert rider, less often with less aggressive riders. Coolant – change yearly, make sure there is at least a 50/50 mixture of antifreeze if freezing temperatures are possible. Steering bearings – Check daily for looseness or play. Adjust and regrease as needed. Swingarm – Check often for looseness. Regrease several times a year. Replace bushings if any play is evident. Sprockets – check for worn or curved teeth each time chain is adjusted. Chain roller& wear pads – check roller for free rotation when checking chain. Make sure roller is not bent or damaged. Check chain wear strips on swingarm and chain guide frequently. Replace as needed to prevent chain from damaging motorcycle. Spokes – Check after each race or after each day of riding for looseness or damage. Wheels & tires – check wheels after each race for dents, cracks or other damage. Check tires for cuts, damage or wear. Check tire pressure daily and adjust for riding conditions. Shock – Check shaft area daily for signs of oil leakage or damage. Check swingarm and shock bushings for looseness. Forks – Check forks daily for leaking oil or damage to tubes. Make sure forks are not twisted check for smooth operation. Spark plug – check sparkplug color and condition after each race or end of riding day. Adjust jetting to keep plug from fouling or overheating. Silencer – If bike seems to be getting louder, replace packing and decarbonize inner tube. Expansion pipe – check daily for large dents, damage or leakage. Remove carbon from headpipe when pipe is removed. Have large dents fixed, or any dents within 8″ of the cylinder. Replace o-rings on pipe as needed to maintain a good seal. Footpegs – check daily for proper operation, pegs should spring back into place. Make sure pegs are not bent or overly dull. Handlebars – check bars after any crash for bending. Look for cracks near bar clamps. Replace bars that have been straightened more than 2 or three times, or if bar is badly bent. Aweakened bar can snap suddenly causing injury to rider. Throttle – check throttle for proper operation each time before bike is started. Remove and clean inside of grip and bar as needed. Grips – check grips daily for wear or looseness. Replace as needed. Use grip glue & safety wire to help hold grips in position. Calipers & pads – check pad wear and caliper function daily or after each race. Replace pads and clean calipers as needed. Brake lever – check lever daily for damage or wear. Make sure lever is at proper angle for both seated and standing positions. Leave lever clamp loose enough to allow clamp to rotate during crash rather than breaking lever. Check and adjust freeplay as needed. Brake pedal – Check pedal daily for damage and proper freeplay. Adjust rear caliper as needed. Reeds – Remove and inspect reed block during every ring change. Check reeds for signs of wear, fraying and cracking. Make sure reeds sit flat and seal well. Replace at any sign of wear or damage or at least once a year, more often for expert riders. Nuts & bolts – Check all nuts and bolts regularly. Make sure to check engine mounting bolts and swingarm bolt frequently

Incoming search terms:

2001 – 2003 Highlander FRONT DOOR OPENING WEATHERSTRIP

0

Filed Under (Toyota Manuals) by admin on 27-10-2011

download
have been improved to better resist deformation or tearing at the bottom center portion of the front door frame. Replace the front door opening weatherstrips on vehicles with this condition built prior to the VIN breaks listed in the Production Change Information section below. 2001 – 2003 model year Highlander vehicles produced BEFORE the Production Change Effective VINs shown below. MODEL ENGINE TYPE PRODUCTION CHANGE EFFECTIVE VIN 4Cylinder 4×2 JTEGD21A#30052511 Highlander 4 Cylinder 4×4 JTEHD21A#30020710 Highlander 6Cylinder 4×2 JTEGF21A#30085273 6 Cylinder 4×4 JTEHF21A#30113260 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME QTY 62311-48020-## Same Weatherstrip, Fr Door Opening, RH 1 62312-48020-## Same Weatherstrip, Fr Door Opening, LH 1 Replace the front door opening weatherstrip as shown in the Technical Information System (TIS). Refer to the 2001 – 2003 Highlander Repair Manual; Exterior/Interior Trim, Roof Headlining Assembly

2001 YAMAHA TDM900 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 20-11-2010

download
CHECKING THE SWITCHES ELEC EAS00731 ELECTRICAL CHECKING THE SWITCHES Check each switch for damage or wear, proper connections, and also for continuity between the terminals. Refer to “CHECKING SWITCH CONTINUITY”. Damage/wear Repair or replace. Improperly connected Properly connect. Incorrect continuity reading Replace the switch. -3- ELECTRIC STARTING SYSTEM ELEC EAS00755 ELECTRIC STARTING SYSTEM CIRCUIT DIAGRAM -4- ELECTRIC STARTING SYSTEM ELEC 4 Main fuse 5 Battery 7 Starter relay 8 Starter motor 9 Main switch 12 Starting circuit cut-off relay 13 Sidestand switch 14 Neutral switch 49 Clutch switch 59 Engine stop switch 60 Start switch 61 Ignition fuse -5- ELECTRIC STARTING SYSTEM ELEC EAS00756 STARTING CIRCUIT CUT-OFF SYSTEM OPERATION If the engine stop switch is set to “” and the main switch is set to “ON” (both switches are closed), the starter motor can only operate if at least one of the following conditions is met: The transmission is in neutral (the neutral switch is closed). The clutch lever is pulled to the handlebar (the clutch switch is closed) and the side- stand is up (the sidestand switch is closed). The starting circuit cut-off relay prevents the starter motor from operating when neither of these conditions has been met. In this instance, the starting circuit cut-off relay is open so current cannot reach the starter motor. When at least one of the above conditions has been met the starting circuit cut-off relay is closed and the engine can be started by pressing the starter switch. WHEN THE TRANSMISSION IS IN NEUTRAL WHEN THE SIDESTAND IS UP AND THE CLUTCH LEVER IS PULLED TO THE HANDLEBAR 4. Starting circuit cut-off relay Disconnect the starting circuit cut-off relay from the wire harness. Connect the pocket tester (Ω 1) and battery (12 V) to the starting circuit cut-off relay terminals as shown. YES NO Replace the starting circuit cut-off relay. Does the starting circuit cut-off relay have continuity between blue/white and black? EAS00759 Continuity Tester positive probe sky blue Tester negative probe blue/yellow No conti- nuity 1 2 1 3 Tester positive probe sky blue Tester negative probe black/yellow Battery positive terminal red/black Battery negative terminal black/yellow 1 2 Tester positive prove blue/white Tester negative prove black 3 4 5. Starting circuit cut-off relay (diode) Disconnect the starting circuit cut-off relay from the wire harness. Connect the pocket tester (Ω 1) to the starting circuit cut-off relay terminals as shown. Measure the starting circuit cut-off relay for continuity as follows. Tester positive probe blue/green Tester negative probe blue/yellow 4 3 Tester positive probe black/yellow Tester negative probe sky blue 2 1 Tester positive probe blue/yellow Tester negative probe sky blue 3 1 Tester positive probe blue/yellow Tester negative probe blue/green 3 4 When you switch the tester’s positive and negative probes, the readings in the above chart will be reversed. Are the testing readings correct? YES NO Replace the starting circuit cut-off relay. NOTE: EAS00760

Incoming search terms:

Incoming search terms: