how does a rancher 420 drive shaft come out

You search Auto repair manual PDF how does a rancher 420 drive shaft come out, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how does a rancher 420 drive shaft come out Direct Download speed 5282 Kb/s

  how does a rancher 420 drive shaft come out Full Version speed 6162 Kb/s



KTM 3V TURBO DRIVE MODEL 9808T KNEE FEED Installation and Removal Manual

0

Filed Under (KTM) by admin on 28-01-2012

download
Gather together the following items that you will need to complete this installation. a) lathe b) 3/8″ electric hand drill c) 9/32″ diameter transfer punch SERVO Turbo Drive Model 9808T Page 2 d) .4375 drill, 3/16″ drill, #7 drill e) 1/4-20 tap f) 3/4″ socket wrench g) set of inch hex wrenches h) clean shop rag Step 2: Clean the power feed mounting area completely. Step 3: Remove the drive clutch nut and the drive clutch from the elevating jack shaft. Step 4: Remove the dial nut, dial, and dial carrier. Keep the dial for reuse later. Step 5: Remove the existing bearing retainer. Keep the screws for reuse later. Step 6: Pull jack shaft out of knee. Hold inboard end up while removing to avoid damage to the pinion gear. Step 7: Press the bearing off the jack shaft. Step 8: Drill and ream the end of the jack shaft .4375″ diameter by 13/16″ deep. The .4375″ dia. must be concentric to the shaft O.D. within .002″ T.I.R. Chamfer 1/32″ x 1/2″ diameter. For best results, machining should be done in a lathe. Step 9: Place the shaft extension #6975 into the end of the jack shaft. Finish drill 3/16″ diameter through the shaft and pin the extension with the 3/16″ diameter x 5/8″ long roll pin. File smooth. Step 10: Reassemble and replace the jack shaft in the machine. Step 11: Replace the existing bearing retainer with #57904 retainer provided. Secure using existing screws. Step 12: Slip spacer #5426 and bearing race #1616 onto the jack shaft. Slide the adaptor #0771 over the bearing race and locate against front of the knee.

Incoming search terms:

HONDA 420 RANCHER 2×4/4×4 2007-2009 CLUTCH KIT INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-12-2011

download
Remove key from the ignition switch. Remove the side panels from both sides. Remove both foot wells. 2. Drain coolant. Remove the oil drain plug from the motor; if you carefully drain it into a clean container you should be able to reuse it. 3. Disconnect shift motor (on electric shift models only). Remove coolant hoses. 4. Remove the bolts that mount the front differential to the frame, no other parts need to be removed. Carefully slide the front differential towards the front of the machine; you might need to lift up slightly to get the differential to move. Remove the drive shaft. Remove o-ring on output shaft (on motor). 5. Remove the fuel pump. 6. Loosen the front crankcase cover bolts, keep track of each bolt length and location. Slowly remove the crankcase cover. Carefully watch for o-ring shims and dowel pins that may fall out. 7. Unstake the nut holding the clutch on and remove nut. Using Honda tool #07933-HB3000A thread the large part of the tool into the center of the clutch. Tighten the center bolt on the tool while holding the large part of the tool with a wrench. This will pull the clutch off the machine. Place the clutch on a clean work surface. EPI performance.com
8. Using the c-clamps push down slightly on the outside cover and remove the four e-clips. Keeping track of which way they come off, remove the round metal plates one at a time. This will allow you to see the complete spring. Remove one end of each spring using a spring tool or needle nose pliers and then remove springs. Install the EPI springs by inserting the spring into the outer edge first. Using a spring tool or pliers (45 degree bent pliers work well) pull on the spring and insert the end into the hole. Install the metal plates and the e-clips. If you can’t get the plates to sit flat make sure each clutch arm is flat against the bottom plate of the clutch. Occasionally when you put the springs on, the clutch arms will pop up. Slide the clutch into the machine. The Sprague clutch is marked “outside” when installing make sure this is facing out. Torque clutch nut to 87 ft/lbs. 9. Clean the gasket surface on the motor and on the cover. Put a thin layer of Honda Bond or Yamabond semi-drying liquid gasket (or something similar as long as it is semi-drying) on the crankcase cover. Carefully install crankcase cover, do not force cover on. Torque bolts to 9 ft/lbs. 10. Install the fuel pump. 11. Install the o-ring on the output shaft (on motor) and install the drive shaft. Carefully slide the front differential back into place and mount to the frame. Install the coolant hoses. Refill your engine coolant to the proper level according to your owner’s manual. 12. Install the oil drain plug. Refill your engine to the proper level according to your owner’s manual. You can reuse your oil if it is clean and was drained into a clean container. Only use manufactures recommended oil. 13. Be sure to double check coolant and oil levels and to look for any leaks after the machine has run for a few minutes. 14. Go out and ride your machine. If your performance doesn’t seem right double check to make sure everything has been done properly. 15. EPI is constantly testing our products. Sometimes there is a need to contact the user with new technical information. To ensure that you are receiving this information visit our web site EPIperformance.com to register your clutch kit.

Incoming search terms:

Electronic Speedo Drive for Toyota T50 5 Speed Transmission

0

Filed Under (Toyota Manuals) by admin on 20-09-2011

Download
Disassembly is simple, remove the “C” clip from the drive housing , just above the drive gear. This will allow the shaft/gear assembly to be withdrawn from the housing. Remove the “O” ring from the housing. Wash all parts internally and externally to remove oil, grease and road grime This will allow the shaft/gear assembly to be withdrawn from the housing. Remove the “O” rings from the housing. Remove the three (3) philips head screws from the cover on the top of the drive housing. Carefully remove cover, be aware that the small parts in side may be stuck to the cover. Remove all internal parts, record order of assembly. Wash housing and shaft to remove oil, grease and road grime. The T50 drive shaft needs to be shortened to a similar length to the AE101. I reassembled the AE101 shaft and housing, and then measured from the top face of the AE101 housing down to the top of the AE101 drive shaft. ( Fig.4) Record this reference depth, (I got 17mm)

Incoming search terms:

HARLEY DAVIDSON SHIFTER SHAFT COVER WITH INSERT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1 2 4 3 5 6 7 is01872 1. Shifter shaft 2. Inner cover 3. Toe shifter lever 4. Outer cover 5. Set screw (for outer cover) 6. Set screw (for inner cover) 7. Casting Figure 1. Shifter Shaft Covers 1. See Figure 1. Remove the stock heel shift lever and toe shift lever (3) from the gear shifter shaft (1). 2. Install the set screw (6) into the inner gear shifter shaft cover (2). 3. Install inner gear shifter shaft cover with installed set screw over the casting (7) in-board of the shifter shaft (1). 4. Tighten the set screw until light contact is made with the casting. Do not overtighten. 5. Re-install toe shift lever on the gear shifter shaft. Tighten the shifter retaining screw to 18-22 lb-ft (24-30 Nm) . 6. Install the set screw (5) into the outer gear shifter cover (4). 7. Install outer gear shifter shaft cover with installed set screw over the end of the gear shifter shaft (1). 8. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw. SERVICE PARTS

Incoming search terms:

Harley-Davidson CHAIN DRIVE INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 15-04-2012

download
1) Assemble & install the chain tensioner assembly over the primary chain as shown in figure 1. 2) Install the compensator sprocket with extender & spacer (numbers 5, 6, & 7, FIG 2)(#7 is not included in this kit), primary chain, chain tensioner, and clutch basket simultaneously onto the motor drive shaft & transmission main shaft. Rotate the chain drive slightly as needed to allow the splines to line-up. 3) Install the chain tensioner nut loosely on the chain tensioner bolt. 4) Install the sliding cam onto the compensator sprocket, & slide the compensating sprocket cover-assembly (#3) over the cam. 5) Apply 2 drops of Rivera “Red” thread-lock on the threads of the motor drive shaft, & install the motor nut loosely with the fingers at this time. The hex spacer (#7) and spacer (#2) as seen in fig.2 are not provided in Rivera Engineering’s chain drive kit. These components are required with some applications, and can be purchased from your local Harley-Davidson dealer. FIG 2 6) Apply 2 drops of Rivera “red” thread-lock on the threads of the transmission main-shaft and loosely install the clutch hub nut (left hand threads). 7) Place the HD “Primary Drive Locking Tool” HD-41214 on the primary chain as shown in figure XXX and tighten the motor sprocket nut to 150-165 foot-pounds. 8)Turn the locking tool 180 degrees and move it to the clutch sprocket. Tighten the clutch hub nut to 70-80 foot pounds (left- hand thread). Adjust chain tension so that the top strand has 5/8″- to-7/8″ of up and down play (cold drive train). Tighten the center bolt nut to 21-29 foot pounds of torque.

Incoming search terms:

HONDA VTX, VTX RETRO AND VALKYRIE DRIVE SHAFT COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Place the cover over the drive shaft housing. 2. Hook one end of the springs provided into the lower holes. Wrap the springs around the backside of the drive shaft housing. Using a needle nose pliers stretch the springs and hook them into the upper holes. 3. Note; if springs are too long, shorten and reform end to be able to hook spring in place.

Incoming search terms:

HARLEY DAVIDSON 45-AMP. UPGRADE ALTERNATOR ROTOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
This 45-amp Rotor Kit is designed for installation on 1999 and later FLHT, FLHTC, FLHR, FLHRI, FLHRCI and FLTR Model Motorcycles. Existing Rotor Removal 1. Remove seat and disconnect battery terminals, negative cable first. 2. Follow instructions in applicable Service Manual and remove the primary chaincase cover. Remove the clutch, primary chain, compensating sprocket and shaft extension as a single assembly. 3. Remove the alternator rotor spacer, if present. Installation The laminated high-output rotor in this kit contains magnets that are considerably more powerful than those used in most previous rotors. The ROTOR REMOVER/INSTALLER and SHAFT PROTECTOR SLEEVE (HD-41771) must be used to prevent parts damage during rotor removal and installation. 1. See Figure 1. Verify threads are clean and thread the Shaft Protector and Rotor Remover/Installer, if removed. NOTE The Shaft Protector Sleeve not only protects the threads from the splines of the rotor, but acts as a guide to ensure that the rotor is properly centered. 2. Turn thumbscrews of Rotor Remover/Installer into threaded holes in rotor face. CAUTION 1 WARNING 1 WARNING 1 WARNING Kit Number 29999-97B Figure 1. Install Shaft Protector and Rotor Installer Engine Sprocket Shaft 1. Make Sure Threads are Clean 2. Install shaft protector sleeve. Shaft protector sleeve 3. Install Rotor Remover/Installer i04153 Handle Thumbscrew Forcing screw . Center ball on forcing screw in recess at end of engine sprocket shaft. Rotate the handle of the tool in a counterclockwise direction to ease rotor into position over stator. 4. Loosen thumbscrews and remove Rotor Remover/Installer. Remove Shaft Protector Sleeve. 5. Install the shaft extension on engine sprocket shaft. No alternator rotor spacer is necessary). 6. Follow instructions in applicable Service Manual and install the clutch assembly, primary chain and shaft extension as a single assembly. 7. Apply two drops of Red LOCTITE®262 to threads of clutch nut and engine sprocket nut. Tighten nuts as fol- lows: Clutch nut- (left hand threads), 70-80 ft-lbs (94.9-105.5 Nm) Engine sprocket nut- 150-165 ft-lbs (203-223 Nm). 8. Follow instructions in Service Manual and install the Primary Chaincase Cover using new gasket from kit, if necessary.

Incoming search terms:

Honda 2007-2010 Rancher 420 ATV Rear Bumper Installation

0

Filed Under (Honda) by admin on 22-12-2011

download
Honda Rancher 420 ATV Rear Bumper (2007-2010) Installation Instructions 1. Attach top bumper attachments to top rack. 2. Attach the rear bumpers lower attachment point to vertical bars

Incoming search terms:

HARLEY DAVIDSON GEAR SHIFTER SHAFT COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
Models This kit fits 1982 and later Touring and FL Softail model motorcycles. Kit Contents Table 1. Kit Contents Part Number Description (Quantity) Not Sold Separately Gear shifter shaft cover Not Sold Separately Screw, set There are no Service Parts available with this kit. INSTALLATION 1. Remove the stock heel shift lever from the gear shifter shaft. 2. Install the set screw into the gear shifter shaft cover. 3. Install gear shifter shaft cover with installed set screw over the end of the gear shifter shaft. 4. Tighten the set screw until light contact is made with the shaft groove. 5. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw.

Harley-Davidson Motorcycle Reverse Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
2.1 Obtain a small tube of Loctite® #262 (red) for use later. 2.2 Drain the transmission oil. 2.3 Remove the clutch adjustment cover (left side). 2.4 Remove rear exhaust header pipe (cross over exhaust pipe). 2.5 Remove the muffler support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove clutch push rod and oil slinger. To be disassembled and modified later. 2.8 Remove the two nuts from the main (rear) and counter (front) transmission shafts. 2.9 Remove the transmission bearing housing (puller available from Champion Sidecars). To be replaced with new reverse gear transmission bearing housing (Trap Door). 2.10 Cover the exposed gears in the transmission with a cloth in preparation to cut the shifter fork shaft. 3 Install New Main and Countershaft Gears NOTE: Gears and Tapered Split Rings are factory matched sets. Do not mix!. 3.1 Locate the shifter fork rod, mark fork rod flush at transmission case and pull out 1/4″. Figure 1 Figure 2. Exposed Shoulders Mark shifter fork rod flush with case Remove Spacers Vehicle Transmission Counter Shaft Main Shaft Front of Motorcycle Figure 1
Reverse Gear Installation Instructions For EVO / 5 Speed and Twin Cam Harley-Davidson® Motorcycle Page 3 of 6 Revision 7 © 2007 Champion Motorcycle Accessories International, Inc. dba Champion Sidecars 11841 Monarch Street Garden Grove, CA 92841 (800) 875-0949 (714) 847-0949 www.championsidecars.com www.championtrikes.com Figure 6 CAUTION: Do not pull the shifter fork rod out of the transmission more than 1/4″. If you pull the shifter fork rod out too far, it will be difficult to realign it with the internal shifter fork. 3.2 Cut the shaft at the mark and push it back in. The shaft end MUST NOT stick out of the transmission case. If the shaft is in deeper, fill the hole with silicone to prevent the shaft from moving in and out. NOTE: Shifter fork is made of non-tempered metal and may be cut with a hacksaw or Dremel® cutting tool. 3.3 Important: Remove stock spacers from main and counter shafts. Spray with silicon remover (Brake-Clean) then, using supplied cleaning pad, clean shafts, new counter and main shaft gears and tapered lock rings (inside and outside) Figure 1 3.4 With motorcycle in neutral, pull both the shafts out and simultaneously push the OEM outermost gears in until seated completely to expose the shoulders of both shafts. The countershaft shoulder should be flush with the gear face. For the main shaft the gear would “hang over” the shoulder a small bit. Figure 2 3.5 Apply supplied Champion Super-Lock retaining compound to the inside and outside surfaces of the large gear tapered split ring, to the inside of the new countershaft gear (large gear) and to the transmission countershaft (the forward most shaft). 3.6 Install new countershaft gear to the transmission countershaft. Insert tapered split ring (tapered end first) into the countershaft gear. Install ring seat tool and spring to counter shaft and new countershaft gear. Torque ring seat tool to 40 ft-lb’s. Figures 3 and 4

Incoming search terms:

Incoming search terms: