Filed Under (Tips and Review) by admin on 21-11-2010
Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed. • Do not leave the main switch in the on position for an extended period of time if the engine is not running Off Position: • All electrical circuits are off and the engine is stopped. The key can be removed in this position. Steering Lock Position: • Turn the handlebars to the left as far as they will turn, turn the key to the lock position and remove. Steering Lock Position On Position Off Position Wildfire WFH50-S2 Maintenance Table The X indicates at how many miles you need to check the Item. Must change oil: change before riding, again at 500 miles and then 2500 or yearly which ever comes first. Capacities Fuel Capacity: 1 gallon Final drive oil capacity: 3.5 ounces Tire air pressure: Front 28 psi and rear 32 psi. ITEM 500 1000 20002500 3500 40004500 5000 60006500 Check Daily Engine Oil and Filter X X X X X X Gear Oil X X X X Valve Clearance X X Cam Chain X X Carburetor X X Air Cleaner Clean Every 1500 miles, Replace Every 3500 miles Fuel Filter Clean Every 1000 miles, Replace if Necessary Brake System X X X X X X X Drive Belt X Screws and Nuts X X X X X *When riding in a dusty environment, check and clean the air filter element more often. Battery • This scooter uses a sealed lead acid battery, it is unnecessary to check or add liquid. NOTE: Never open the electrolyte of a sealed battery. Remove the battery from the scooter and store separately in a well ventilated area when the scooter is not in operation for long periods of time Speedometer • Speed is measured in mph. Odometer • The total riding distance is indicated. Fuel gauge • The gauge indicates how much fuel is in the tank (the gauge does not work when the ignition switch is off). The needle moves from full “F” to empty “E” as your fuel decreases. Fill the tank with a good grade of 89-90 octane unleaded gasoline. High Beam Indicator LIght • The high beam light indicates that the high beam headlight is in use. NOTE: Apply the low beam to avoid obstructing the view of other drivers. Turn Signal Indication Light • The turn signals indicate that you are turning a chosen direction, push the button in the desired turning direction, it will return to the center, press the button in to turn off. Speedometer Odometer Turn Signal Indication Light High Beam Indication Light Fuel Gauge 4 General Safety Precaution • Scooters can be hazardous to operate. Please operate it with the following safety instruction. If you fail to take proper precautions, a collision or fall may quickly occur. If you have any questions as to the operating condition of your scooter, turn off the engine and walk your scooter. These scooters should be ridden by persons with good vision, balance, coordination, reflex, strength and decision making capability. • Please read this manual and all safety labels carefully, and follow correct operating procedures. • Before each time you ride make sure that the brakes work properly. • Never operate your scooter without wearing proper safety equipment that includes helmet, shoes, etc… • Never operate your scooter under influence of alcohol or drugs. • Always ride with both hands on the handle bars. • Never operate at excessive speeds. Proper speed is determined by terrain, visibility, operating condition and experience. • Never attempt wheelies, jumps or other stunts. • Always inspect your scooter prior to each use to make sure all bolts are tight, and is in safe operating condition.
Filed Under (Harley Davidson) by admin on 28-11-2010
During Break-In At 50 Miles (80 Kilometers): 1- Change engine oil and filter. 2- Inspect for fuel and oil leaks. 3- Inspect air cleaner element and service as required. 4- Check tightness of exterior fasteners, except head bolts. Engine Maintenance at 500 Miles (800 Kilometers): 1- Change engine oil and filter. 2- Inspect for fuel and oil leaks. 3- Inspect air cleaner element and service as required. 4- Check tightness of exterior fasteners, except head bolts. 5- Check operation of enrichment device and throttle controls. 6- Check engine idle speed. 7- Check tightness of engine mounts. Regular Service Intervals Regular lubrication and maintenance will help keep your new S&S engine operating at peak performance. The following table presents the required service schedule for normal operating conditions. Failure to complete the required engine maintenance can result in engine damage and an increase in emissions. Please refer to the motorcycle owner’s manual for any additional required chassis maintenance. Engine Service Intervals Item Interval Engine Oil & Filter Change at 50, 500, 2,500 miles (80, 800, 4,000 kilometers), every 2,500 miles (4,000 kilometers) thereafter1 Air Cleaner Element Inspect at 50 and 500 miles (80 and 800 kilometers), every 2,500 miles (4,000 kilometers) thereafter2 Tappet Oil Screen Inspect every 2,500 miles (4,000 kilometers). Replace every 5,000 miles (8,000 kilometers). Petcock, Lines, & Fittings, Vacuum Lines Inspect at 50 and 500 miles (80 and 800 kilometers), every 2,500 miles (4,000 kilometers) thereafter. Fuel Tank Filter Screen & In-Line Fuel Filter (If used) Inspect every 5,000 miles (8,000 kilometers). Engine Idle Speed Adjust as required. Operation of Throttle & Enrichment Device ControlsInspect at 500 miles (800 kilometers) and every 2,500 miles (4,000 kilometers) thereafter. Spark Plugs Inspect every 5,000 miles (8,000 kilometers). Replace every 10,000 miles (16,000 kilometers) or as needed. Ignition Timing Inspect every 5,000 miles (8,000 kilometers). Engine Mounts Inspect at 500 miles (800 kilometers) and every 5,000 miles (8,000 kilometers) thereafter. External Fasteners Except Engine Head Bolts Re-torque at 500 miles (800 kilometers) and every 5,000 miles (8,000 kilometers) thereafter. 1- S&S recommends that petroleum-based oil not specifically formulated for motorcycles should be changed every 1,000 miles (1,600 kilometers) after the break-in period. 2- Replace more frequently if required or if engine is operated in a dusty environment.
Filed Under (Wildfire) by admin on 29-11-2010
Engine Oil Replacement • Replace the engine oil after the first 50 miles or 1 hour with 5w50, 10w50 or 15W50 synthetic engine oil. Then replace again every 1,500 miles or 1 each year. Check oil level every 500 miles, add oil if needed. Changing the Engine Oil (1).Warm up the engine for a few minutes. (2).Stop the engine. (3). Place scooter on center stand. (4).Place an oil pan under the engine and remove the dipstick. (5).Remove the drain plug and drain the oil. Reach in drain hole, pull out filter clean and reinstall, after all oil drains out. (6).Reinstall drain plug. (7). Fill the engine with oil until the level is in the designated area on the dipstick. (8).Start the engine and check for oil leaks. If a leak is found stop the engine immediately and look for cause. Rear Wheel Oil Replacement • Replace the gear oil after the first 500 miles with 5W/50 synthetic engine oil. Replace the gear oil again every 4 months or every 2000 miles. • Replacing the Gear Oil (1).Put the scooter on the center stand (please see photo below) . (2).Place an oil pan under the gear case (please see photo below) . (3).Remove the oil filler bolt and the drain plug to drain the oil (please see photo below) . (4).Reinstall and tighten the drain plug. (5).Fill the gear case with oil (please see photo below) . (6).Reinstall the oil filler bolt. (7).Check for oil leakage. Cleaning Air Cleaner Be sure to check the air cleaner regularly. (1).Place the scooter on the center stand. (2).Unscrew and remove the left side panel. (3).Remove the air cleaner cover by removing the screws. (4).Take out the air cleaner by removing the screws. (5).Remove the air cleaner element and wash it gently, but thoroughly in solvent. Replace if damaged. (6).Squeeze out the excess solvent and dry it. (7).Apply oil to the entire surface of the air cleaner and squeeze out the excess oil. It should be damp but not dripping. (8).Install the air cleaner, cleaner cover, and left side panel. center stand 1 oil pan 2 3 oil drain plug oil pan 5 Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed.
Filed Under (Toyota Manuals) by admin on 10-10-2011
passengers weighing approximately less than 100 pounds, depending on their seating position. It is important for the front seat passengers to know that proper operation of the advanced frontal airbag system is highly dependent on the pressure placed on the seat bottom. Situations that add or subtract sensed weight can result in occupant misclassification. To minimize this situation: Check seating posture. Passengers should be seated upright with their back against the seat back and feet on the floor. Check loading conditions. Extra weight from items, such as bags or groceries or toys, hanging on the seat back can add to the sensed weight of the front seat passenger. A rear seat passenger lifting the front seat with their legs, objects placed under the front seat, or the front seatback in contact with the rear seat can subtract from the sensed weight of the front seat passenger. If the passenger airbag indicator lamp continues to switch ON to OFF after checking the above conditions, perform the following repair procedure. NOTE: The safest place for children is in the rear seat. Please note that Toyota recommends that you never install a rear-facing child restraint in the front passenger seat, even if the passenger “Airbag OFF” lamp is illuminated. Please refer to you Owner’s Manual for additional details. 2004 – 2005 model year Camry, Highlander, and Solara vehicles produced BEFORE the Production Change Effective VINs shown on the following page. 2005 model year Matrix and Corolla vehicles produced BEFORE the Production Change Effective VINs shown on the following page
Filed Under (Uncategorized) by admin on 26-11-2010
• Check before Riding • Make sure the brakes work properly and adjust if necessary. • Check all nuts and bolts for tightness. • Make sure that the gas tank is full. • Check tire pressure. • Check all gauges. • Check and make sure that all of the lights are working properly, headlight, taillight, turn signal etc. • Check the engine oil. STARTING, RIDING, STOPPING AND PARKING Before starting, put the kickstand up. • Practice in an empty area away from people and vehicles. • Always remember to obey your local and state laws and regulations. • Be sure your bike has fuel and oil. • Be sure the bike is in neutral. • Apply the rear brake. • Turn the key on. • Press the electric start button. • After engine warms up, push the choke 1/4 in then 1/2 in and in 1 minute completely off. • If the engine is warm it should start without choking. • For a cold engine, let the engine idle for 1-3 minutes before driving, then begin to turn the choke off. • Never exceed 4 seconds when engaging the starter. • Release the button immediately after the engine starts. • Do not apply the key while the engine is running, it can cause damage to the starter. • Sit on the bike keeping one foot on the ground for stability, release the clutch by pulling in the lever, shift bike into first gear by using the foot shifter. • Apply the throttle gradually as you release the clutch lever slowly until the clutch engages. • To shift into the next gear release the throttle pull the clutch lever in and shift into the next gear, after you shift, gradually apply the throttle and slowly release the clutch. • Use this sequence when shifting to all gears. • Only put your feet on the ground when coming to a stop. • When coming to a stop decrease your speed by releasing the throttle and applying the brakes and the clutch, if the tire skids release the brake and reapply. • Parking: Put your kick stand down. Park away from pedestrians. NOTE: The muffler and exhaust pipe are h