how to adjust a belt on a trike conversion

You search Auto repair manual PDF how to adjust a belt on a trike conversion, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to adjust a belt on a trike conversion Direct Download speed 5282 Kb/s

  how to adjust a belt on a trike conversion Full Version speed 6162 Kb/s



Yamaha Road Star TRIKE CONVERSION KIT Owner's Maintenance Notes

0

Filed Under (Yamaha) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 20-25psig. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm, external differential and axle bearings are sealed and do not require greasing. However, should you experience unusual differential or axle bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Differential lubrication . Your differential is a sealed unit and comes filled with high-pressure grease. No maintenance is required. 5. Brakes . Check your brake system fluid level every 3,000 miles and top-off as necessary. Inspect rear disc brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . Inspect your drive belt as recommended in your motorcycle Owner’s Manual. When properly tensioned after the trike conversion, the belt should “deflect” about 1/2 to 5/8 inches when pressed with a force of 10 pounds. Do not use commercial belt dressing compounds on the belt: these compounds are designed for friction, not toothed, belts and can collect dirt and sand. 7. Suspension System. The suspension system retains your single OEM shock and adds two coil-over “helper” mechanical shocks. The system is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight). There is a pre-load adjuster ring on each new shock that is factory-set at the “lowest” setting, for the softest ride. Changing this setting will result in a stiffer ride

Incoming search terms:

BMW R850, R1100, R1150, R1200 Oilhead Maintenance Manual

0

Filed Under (BMW) by admin on 16-11-2010

download
cold Engine and Drivetrain Procedures Check Alternator Belt Tools Parts T-handle hex – 4mm none Note: In most cases the alternator belt does not need to be checked any more. Early models should have the pulley and belt upgrade that came out a few years ago. Current recommendations are that the belt is installed and adjusted, then not disturbed until 36K when replacement is specified. 1. Remove the four bolts holding the black plastic alternator belt cover at the front of the engine, 4mm T-handle hex. 2. Remove the cover by sliding it straight down. 3. Check the belt for cracks or shredding. 4. Check the belt tension, quite tight, ~1/4″ deflection when you press on the center. Note: Paul Glaves suggests that proper belt tension is when you can twist the belt ~90 degrees, midway between the pulleys. If you can twist it more than 90 degrees, it is too loose. If you cannot twist it 90 degrees, then it is too tight. 5. Leave the cover off for the valve adjustment procedure on the next page. Change Alternator Belt Tools Parts T-handle hex – 4mm alternator belt socket – 13mm ratchet wrench – 13mm torque wrench 1. Remove the four bolts holding the black plastic alternator belt cover at the front of the engine, 4mm T-handle hex. 2. Remove the cover by sliding it straight down. 3. Loosen the 2 nuts and 1 bolt, 13mm, that hold the alternator – one is on top and one is on each side, thus allowing the alternator to pivot down. 4. Remove the old belt. (Some bikes have a pipe that traps the belt – loosen it enough to get the old belt out and the new belt in) 5. Install the new belt being sure it is properly seated. 6. BMW calls for a tensioning torque of 5.9 ft.lb. (8 Nm) on the adjuster bolt on the left side of the bike. You have to get at this bolt from the alternator side and you may have to lift the tank. Alternatively, you can pry the alternator up with a large screwdriver to tension the belt. 7. Once the belt is under proper tension, tighten the 2 nuts and 1 bolt, 13mm, to 15 ft.lb. (20 Nm). 8. Check the belt for proper tension (see above) and proper seating alignment

Incoming search terms:

Harley-Davidson EMERGENCY DRIVE BELT REPLACEMENT KIT Installation Manual

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Shift transmission to neutral. Before installation of the emergency belt, to avoid personal injury and/or vehicle damage, secure the motorcycle. Both stand and motorcycle must be on solid, level ground. Failure to follow instructions could result in death or serious injury. 2. See Figure 1. Remove spring clip (4) (if present) and loosen rear axle nut (1). 3. Loosen rear axle adjuster (3) (or adjuster nut, if so equipped) on each side of motorcycle, and move rear wheel to full forward position. 4. Remove the damaged/broken belt. 5. Inspect sprockets and belt guard (2) for damage and/or debris. Remove any debris. If sprockets and belt guard are not damaged, proceed with the installation. 6. Remove belt guard. 40171-97,40146-00 1 WARNING i06186 Figure 1. Axle 1. Axle nut 2. Belt guard 3. Adjuster 4. Spring clip 2 4 1 3 7. See Figure 2. Install feeder strip on emergency belt. 8. Feed strip around transmission sprocket in a counterclockwise direction over frame cross support. 9. See Figure 3. Interlock the “v” ends of the emergency belt. a. Insert a hex socket key in the fourth (4) and ninth (6) tooth holes. b. Place the splice block (2) over the seventh (5) tooth hole. c. Install a socket head set screw (3) in the seventh tooth. Tighten using another hex socket key. d. Move the block to the next tooth, and repeat installation steps (b) and (c) in each tooth until all 12 screws are installed. NOTE There are 16 screws included in this kit. However, only 12 screws will actually be installed in the belt. The remaining four screws are spares. 10. See Figure 4. Grasp the emergency belt at the mid point of the lower run between your thumb and forefinger and lift the belt up to take up any slack in the belt. Measure the distance that the belt deflects (2) under tension (1). When two pounds of tension is applied to the lower run of the emergency belt, the belt deflection should be within the following measurements

Incoming search terms:

1987 to Current Harley Davidson Softail (FLST Only) Motorcycle Trike Conversion removal and Installation Guide

0

Filed Under (Harley Davidson) by admin on 03-11-2010

download
Removal of Original Parts Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. • Seat (to be re-installed without modification). • Left and right saddle bags (if so equipped). • Left and right rear crash bars, saddlebag rails (if so equipped). • Left and right passenger foot rests (to be re-installed without modification) • Complete exhaust system (to be replaced with new system). • Rear wheel NOTE: Prior to removing rear wheel, depress foot brake and secure in down position (e.g., zip-tie to floor board). This will prevent fluid flow when rear brake caliper is removed • Remove Rear Caliper (disconnect brake line at caliper) NOTE: Cap line to prevent introduction of dust / debris into line. Remove caliper. • Rear Drive Pulley (1987-99 models to be re-installed without modification). • Rear Fender (2000 and newer models, fender mount plates to be reused). • Swing Arm NSTALLING TRIKE CONVERSION KIT 3.1 Sprockets and Drive Belts Specifications See following table for belt installation (1987-99 will use a 4 tooth longer belt) Note : See OEM manual for belt replacement procedure. Year Drive Sprocket OEM Belt New Belt / Sprocket 1987-92 70 T 132 T 136 1993-94 61 T 128 T 132 1995-99 65 T 130 T 136/70TOEM 2000-06 Champion Sprocket, 70 T 135 T Use OEM 2007 Up Champion Sprocket, 66 T Use OEM 3.2 Install Swing Arm É Noting size and location of bolts, remove Cross Assembly from Champion Swing Arm. Do not discard hardware. Figure 1 3.2.1 1987-99 Model Years • Remove bearings from OEM Swing Arm using OEM shop tools and hydraulic press. Note : Although original bearings can be re-used, it is HIGHLY recommended that NEW bearings be installed to Champion Swing Arm a. b. Press bearings into Champion Swing Arm in the same way as the OEM Swing Arm. Using OEM Spacer Tube and supplied washers (four ¾” flat washers), install Champion Swing Arm using OEM bolt, outside washers and nut. Do not torque pivot bolt nut at this time. Figure 2 Note : Insure belt path is over and under Swing Arm pivot. c. d. Replace cross assembly and hardware (previously removed in step 3.2) to Champion Swing Arm. Note that the 2 upper left hand side bolts are countersunk. Torque pivot bolt to OEM specification

Honda Goldwing GL1800 Solid Rear Axle Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Specifications Overall Width: 57.75″ Overall Length: 108″ Overall Length w/EZ-Steer 109.5 Wheel Base: 71″ Extended 4.5″ At Rear Axel Wheel Base w/EZ Steer 72.5″ Load Capacity: 500 Lb Tire Size: 205 / 70 / R15 Wheel Size (15″) Offset +35 mm 15x7JJ 4×4.5 Tire Pressure 20 PSI Suspension: “Zero-Flex” Internal Swing Arm utilizing 3 shocks, OEM shock absorber plus 2 coil over shock absorbers. Rear Differential: Champion Lightweight rear axle / differential assembly. Gear Ratio 2.93:1 gear ratio Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 6.75 cubic feet. 3 full-face helmets and additional storage. Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 7 of 28 Revision 10 4 Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. • Seat (to be re-installed without modification) • Left and right side covers (to be re-installed without modification) • Battery and battery box (to be re-installed without modification) • Left and right saddle bags • Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) • Trunk (to be re-installed without modification) • Left and right passenger foot rests (to be re-installed without modification) • Left and right foot rest under covers (to be modified and re-installed) • Left and right rear crash bars • Saddle bag trunk stay (to be modified and re-installed) • Left and right mufflers (Mufflers only, do not remove decorative covers) • Rear wheel • Left and right pivot bolt covers (to be re-installed without modification) • Reverse resistor (to be relocated) • Swing Arm – Note : Carry out brake system modifications (Section 5) prior to removing Swing Arm. • Note : Upper bolt of mono shock can be removed without removing the fuel tank. • Note : Do not remove actuator hose from actuator pump or shock absorber. Dismounting shock actuator pump will allow more movement of shock absorber when removing swing arm.Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 8 of 28 Revision 10 5 Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm. From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Sidecars Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Sidecars Trike Conversion Kit.

Incoming search terms:

Yamaha Road Star Trike Conversion Installation Manual

0

Filed Under (Yamaha) by admin on 17-02-2011

download
Removal of Original Parts a. Disconnect the battery. b. Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. c. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for re-installation after modification are noted. • Rider’s Seat (to be re-installed without modification) • Passenger Seat (to be reinstalled without modification) NOTE: OEM front / rear seat mount bracket and rear seat mounting bolt to be retained and reused. • Passenger Back Rest w/ Mounting Rails (to be re-installed without modification) NOTE: Back rest to mounting rail hardware to be reused. Mount rail to vehicle frame not to be reused. • Left and right passenger foot rests (to be re-installed without modification) • Drive Pulley / Belt cover (to be re-installed without modification) • Mufflers (to be re-installed and relocated with minor modification) • Rear Fender (complete w/ sub frame and all attaching parts) NOTE: Upper Forward Fender Mounting Bolt to be retained and reinstalled. • Shock Absorber to Swing Arm Mounting Bolt (to be re-installed) • Swing Arm and Rear Wheel (complete w/ all attaching parts) NOTE: Swing Arm Pivot Bolt, washer and nut to be retained and reinstalled. • Brake Line to Rear Master Cylinder • Drive Belt Core Return There are NO core return parts for this model Installation of Champion Trike Conversion Kit 4.1 Install Drive Belt a. Install supplied drive belt to transmission output pulley. (Refer to OEM manual) Figure 1 b. Drive belt cover to be reinstalled later. 4.2 Install Champion Swing Arm a. Install Champion Swing Arm to vehicle using the OEM pivot bolt, washer and nut. Figure 2 b. Attach OEM shock absorber to swing arm using OEM hardware. c. Torque pivot bolt nut to 90 lb. ft. d. Torque lower shock hardware to 43 lb. ft. 4.3 Install Rear Drive Assembly a. Install tension bolts and jam nuts to adjuster

Yamaha Road Star Motorcycles Trike Conversion Removal And Installation Manual

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Removal of Original Parts a. Disconnect the battery. b. Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. c. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for re-installation after modification are noted. • Rider’s Seat (to be re-installed without modification) • Passenger Seat (to be reinstalled without modification) NOTE: OEM front / rear seat mount bracket and rear seat mounting bolt to be retained and reused. • Passenger Back Rest w/ Mounting Rails (to be re-installed without modification) NOTE: Back rest to mounting rail hardware to be reused. Mount rail to vehicle frame not to be reused. • Left and right passenger foot rests (to be re-installed without modification) • Drive Pulley / Belt cover (to be re-installed without modification) • Mufflers (to be re-installed and relocated with minor modification) • Rear Fender (complete w/ sub frame and all attaching parts) NOTE: Upper Forward Fender Mounting Bolt to be retained and reinstalled. • Shock Absorber to Swing Arm Mounting Bolt (to be re-installed) • Swing Arm and Rear Wheel (complete w/ all attaching parts) NOTE: Swing Arm Pivot Bolt, washer and nut to be retained and reinstalled. • Brake Line to Rear Master Cylinder • Drive Belt Core Return There are NO core return parts for this model. nstallation of Champion Trike Conversion Kit 4.1 Install Drive Belt a. Install supplied drive belt to transmission output pulley. (Refer to OEM manual) Figure 1 b. Drive belt cover to be reinstalled later. 4.2 Install Champion Swing Arm a. Install Champion Swing Arm to vehicle using the OEM pivot bolt, washer and nut. Figure 2 b. Attach OEM shock absorber to swing arm using OEM hardware. c. Torque pivot bolt nut to 90 lb. ft. d. Torque lower shock hardware to 43 lb. ft. 4.3 Install Rear Drive Assembly a. Install tension bolts and jam nuts to adjuster plates. Figure 3 Qty per Assm Spec Description 2 M10 x 1.25 x 70 Hex Head Bolt 2 M10 x 1.25 Hex Nut b. Install adjuster plates to rear drive pinch blocks. Hardware installs from inboard to outboard side. Snug, but do not tighten hardware at this time. Figure 4

BMW Poly-V Belt – R 1100 Models

0

Filed Under (BMW) by admin on 16-11-2010

download
Information: In an effort to reduce service volume, a maintenance-free ribbed Poly-V belt was adopted on all R1100 models from engine number 38946130 onwards (09/94 production onwards). This belt does not need to be retentioned (even at the 600 mile service). The old belt required replacement every 24,000 miles. The new style belt is to be replaced every 36,000 miles. Use the same torque procedure as the old belt. Replacement of an old style belt with the new maintenance free belt requires the use of the new parts below: Parts Kit: 12 31 1 342 086 (kit consists of the following) In addition to the Poly-V belt, the following parts were also changed: 1. Top pulley new: steel old: Aluminum 2. Bottom pulley new no spot welds: old: steel w/three spot welds on front 3. Belt new: Ribbed, printing on belt (1342059 Fa. Dayco) or (1341779 Fa. Conti) Slight squeaking may be heard for a short time after a cold start when temperature is below 50°F. The belt should reach it’s correct operating tension soon after the start up. The belt only needs retentioned if the slight squeaking does not stop after warm up.

HONDA GOLD WING GL1500 AND GL1800 TRIKE CONVERSION KIT Owner's Maintenance Notes

0

Filed Under (Honda) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 20-25 psi. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm and wheel bearings are sealed and do not require greasing. However, should you experience unusual wheel bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Rear end lubrication . Your differential comes filled with 1 quart of SAE 85W140 API GL-6 gear oil. You should not have to top-off the differential unless you experience axle seal or pinion seal leaks. Check the oil level every 10,000 miles, or sooner if you experience leaks, and refill as necessary. Do not fill higher than the fill-hole. Change the differential oil every 30,000 – 35,000 miles. 5. Brakes . Check your front and rear brake system fluid levels every 3,000 miles and top-off as necessary. Inspect brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . If your driveshaft U-joint and/or splines are fitted with grease fittings, pump the fittings with wheel-bearing, graphite or high-pressure grease every 3000 to 5,000 miles. If yours does not have grease fittings then lubrication is not required. 7. Suspension System : The suspension system is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight): GL1500: The OEM adjustable air shock is used in conjunction with two (2) new Progressive 416 air shocks. The three shocks should be pressurized to about 20 psig, but to no more than 70 psig; GL1800: You can still use your OEM mono-shock pre-load adjustment. Your two (2) new coil-over shocks do not have an air system connection. However, there is a pre-load adjuster ring on each new shock that is factory-set at the “lowest” setting, for the softest ride. Changing this setting will result in a stiffer ride. 8. EZ-Steer (rake kit) : If your trike is equipped with Champion’s EZ-Steer, the bearings are a wear item. You should follow your motorcycle manufacturer’s recommended front-end triple-tree maintenance requirements. Generally these call for an initial service at 1,000 miles followed by periodic maintenance at 10,000 mile intervals. 9. Electrical : Your trike is pre-wired for a trailer connection. The harness is just below the trunk door on the underside of the body.

Incoming search terms:

HARLEY DAVIDSON SECONDARY BELT EMERGENCY KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
The 40101-80 kit, with a 126 tooth belt, fits: •1980-1986 FXB and 1984-1986 FXWG models This kit may also be used on 1989-1992 international Softail models with a 127 tooth belt. The 40171-97 kit, with a 130 tooth belt, fits: •1995 and later domestic Softail models •1994 and later international Softail models •1994 and later international Dyna models The 40109-86 kit, with a 132 tooth belt, fits •1986-1992 and 1994 domestic Softail models •1989-1993 international FLT and FXR models This kit may also be used on the following models with 133 tooth belts: •1991 and later domestic Dyna models •1991-1992 international Dyna models •1994-1995 international FLT models The 40100-85 kit, with a 136 tooth belt, fits: •1985-1994 domestic FXR models •1985-1996 domestic FLT models •1996 international FLT models The 40112-97 kit, with a 139 tooth belt fits •1997 FLT models Installation 1. Put transmission in ‘Neutral’. 2. Loosen rear axle nut. Loosen rear axle adjuster nut on each side of motorcycle, and move rear wheel to full forward position. 3. Remove the damaged/broken belt. 4. Inspect sprockets and belt guard for damage and/or debris. Remove any debris. If sprockets and belt guard are not damaged, proceed with the installation. 5. See Figure 1. Remove belt guard. 6. See Figure 2. Install feeder strip on emergency belt. Feed strip around transmission sprocket in a counterclockwise direction over frame cross support.

Incoming search terms: