how to adjust the belt on a wildfire 50cc scooter

You search Auto repair manual PDF how to adjust the belt on a wildfire 50cc scooter, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to adjust the belt on a wildfire 50cc scooter Direct Download speed 5282 Kb/s

  how to adjust the belt on a wildfire 50cc scooter Full Version speed 6162 Kb/s



WILDFIRE WFH50-S2 Gas Scooter Owner’s Manual

0

Filed Under (Tips and Review) by admin on 21-11-2010

download
Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed. • Do not leave the main switch in the on position for an extended period of time if the engine is not running Off Position: • All electrical circuits are off and the engine is stopped. The key can be removed in this position. Steering Lock Position: • Turn the handlebars to the left as far as they will turn, turn the key to the lock position and remove. Steering Lock Position On Position Off Position Wildfire WFH50-S2 Maintenance Table The X indicates at how many miles you need to check the Item. Must change oil: change before riding, again at 500 miles and then 2500 or yearly which ever comes first. Capacities Fuel Capacity: 1 gallon Final drive oil capacity: 3.5 ounces Tire air pressure: Front 28 psi and rear 32 psi. ITEM 500 1000 20002500 3500 40004500 5000 60006500 Check Daily Engine Oil and Filter X X X X X X Gear Oil X X X X Valve Clearance X X Cam Chain X X Carburetor X X Air Cleaner Clean Every 1500 miles, Replace Every 3500 miles Fuel Filter Clean Every 1000 miles, Replace if Necessary Brake System X X X X X X X Drive Belt X Screws and Nuts X X X X X *When riding in a dusty environment, check and clean the air filter element more often. Battery • This scooter uses a sealed lead acid battery, it is unnecessary to check or add liquid. NOTE: Never open the electrolyte of a sealed battery. Remove the battery from the scooter and store separately in a well ventilated area when the scooter is not in operation for long periods of time Speedometer • Speed is measured in mph. Odometer • The total riding distance is indicated. Fuel gauge • The gauge indicates how much fuel is in the tank (the gauge does not work when the ignition switch is off). The needle moves from full “F” to empty “E” as your fuel decreases. Fill the tank with a good grade of 89-90 octane unleaded gasoline. High Beam Indicator LIght • The high beam light indicates that the high beam headlight is in use. NOTE: Apply the low beam to avoid obstructing the view of other drivers. Turn Signal Indication Light • The turn signals indicate that you are turning a chosen direction, push the button in the desired turning direction, it will return to the center, press the button in to turn off. Speedometer Odometer Turn Signal Indication Light High Beam Indication Light Fuel Gauge 4 General Safety Precaution • Scooters can be hazardous to operate. Please operate it with the following safety instruction. If you fail to take proper precautions, a collision or fall may quickly occur. If you have any questions as to the operating condition of your scooter, turn off the engine and walk your scooter. These scooters should be ridden by persons with good vision, balance, coordination, reflex, strength and decision making capability. • Please read this manual and all safety labels carefully, and follow correct operating procedures. • Before each time you ride make sure that the brakes work properly. • Never operate your scooter without wearing proper safety equipment that includes helmet, shoes, etc… • Never operate your scooter under influence of alcohol or drugs. • Always ride with both hands on the handle bars. • Never operate at excessive speeds. Proper speed is determined by terrain, visibility, operating condition and experience. • Never attempt wheelies, jumps or other stunts. • Always inspect your scooter prior to each use to make sure all bolts are tight, and is in safe operating condition.

BMW R850, R1100, R1150, R1200 Oilhead Maintenance Manual

0

Filed Under (BMW) by admin on 16-11-2010

download
cold Engine and Drivetrain Procedures Check Alternator Belt Tools Parts T-handle hex – 4mm none Note: In most cases the alternator belt does not need to be checked any more. Early models should have the pulley and belt upgrade that came out a few years ago. Current recommendations are that the belt is installed and adjusted, then not disturbed until 36K when replacement is specified. 1. Remove the four bolts holding the black plastic alternator belt cover at the front of the engine, 4mm T-handle hex. 2. Remove the cover by sliding it straight down. 3. Check the belt for cracks or shredding. 4. Check the belt tension, quite tight, ~1/4″ deflection when you press on the center. Note: Paul Glaves suggests that proper belt tension is when you can twist the belt ~90 degrees, midway between the pulleys. If you can twist it more than 90 degrees, it is too loose. If you cannot twist it 90 degrees, then it is too tight. 5. Leave the cover off for the valve adjustment procedure on the next page. Change Alternator Belt Tools Parts T-handle hex – 4mm alternator belt socket – 13mm ratchet wrench – 13mm torque wrench 1. Remove the four bolts holding the black plastic alternator belt cover at the front of the engine, 4mm T-handle hex. 2. Remove the cover by sliding it straight down. 3. Loosen the 2 nuts and 1 bolt, 13mm, that hold the alternator – one is on top and one is on each side, thus allowing the alternator to pivot down. 4. Remove the old belt. (Some bikes have a pipe that traps the belt – loosen it enough to get the old belt out and the new belt in) 5. Install the new belt being sure it is properly seated. 6. BMW calls for a tensioning torque of 5.9 ft.lb. (8 Nm) on the adjuster bolt on the left side of the bike. You have to get at this bolt from the alternator side and you may have to lift the tank. Alternatively, you can pry the alternator up with a large screwdriver to tension the belt. 7. Once the belt is under proper tension, tighten the 2 nuts and 1 bolt, 13mm, to 15 ft.lb. (20 Nm). 8. Check the belt for proper tension (see above) and proper seating alignment

Harley-Davidson EMERGENCY DRIVE BELT REPLACEMENT KIT Installation Manual

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Shift transmission to neutral. Before installation of the emergency belt, to avoid personal injury and/or vehicle damage, secure the motorcycle. Both stand and motorcycle must be on solid, level ground. Failure to follow instructions could result in death or serious injury. 2. See Figure 1. Remove spring clip (4) (if present) and loosen rear axle nut (1). 3. Loosen rear axle adjuster (3) (or adjuster nut, if so equipped) on each side of motorcycle, and move rear wheel to full forward position. 4. Remove the damaged/broken belt. 5. Inspect sprockets and belt guard (2) for damage and/or debris. Remove any debris. If sprockets and belt guard are not damaged, proceed with the installation. 6. Remove belt guard. 40171-97,40146-00 1 WARNING i06186 Figure 1. Axle 1. Axle nut 2. Belt guard 3. Adjuster 4. Spring clip 2 4 1 3 7. See Figure 2. Install feeder strip on emergency belt. 8. Feed strip around transmission sprocket in a counterclockwise direction over frame cross support. 9. See Figure 3. Interlock the “v” ends of the emergency belt. a. Insert a hex socket key in the fourth (4) and ninth (6) tooth holes. b. Place the splice block (2) over the seventh (5) tooth hole. c. Install a socket head set screw (3) in the seventh tooth. Tighten using another hex socket key. d. Move the block to the next tooth, and repeat installation steps (b) and (c) in each tooth until all 12 screws are installed. NOTE There are 16 screws included in this kit. However, only 12 screws will actually be installed in the belt. The remaining four screws are spares. 10. See Figure 4. Grasp the emergency belt at the mid point of the lower run between your thumb and forefinger and lift the belt up to take up any slack in the belt. Measure the distance that the belt deflects (2) under tension (1). When two pounds of tension is applied to the lower run of the emergency belt, the belt deflection should be within the following measurements

BMW Poly-V Belt – R 1100 Models

0

Filed Under (BMW) by admin on 16-11-2010

download
Information: In an effort to reduce service volume, a maintenance-free ribbed Poly-V belt was adopted on all R1100 models from engine number 38946130 onwards (09/94 production onwards). This belt does not need to be retentioned (even at the 600 mile service). The old belt required replacement every 24,000 miles. The new style belt is to be replaced every 36,000 miles. Use the same torque procedure as the old belt. Replacement of an old style belt with the new maintenance free belt requires the use of the new parts below: Parts Kit: 12 31 1 342 086 (kit consists of the following) In addition to the Poly-V belt, the following parts were also changed: 1. Top pulley new: steel old: Aluminum 2. Bottom pulley new no spot welds: old: steel w/three spot welds on front 3. Belt new: Ribbed, printing on belt (1342059 Fa. Dayco) or (1341779 Fa. Conti) Slight squeaking may be heard for a short time after a cold start when temperature is below 50°F. The belt should reach it’s correct operating tension soon after the start up. The belt only needs retentioned if the slight squeaking does not stop after warm up.

HARLEY DAVIDSON SOFTAIL CHROME LOWER BELT GUARD INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
REMOVING STOCK PLASTIC LOWER BELT GUARD 1. See Figure 1. Remove the hex head bolt (2), washer (3), acorn nut (5), hex head screw (4) and acorn bolt (8) attaching plastic belt guard to rear fork. 2. Remove the plastic belt guard. Save fasteners (2), and (4), washer (3), acorn nut (5) and acorn bolt (8) for installing new chrome belt guard. INSTALLING CHROME LOWER BELT GUARD 1. See Figure 2. Position the new chrome belt guard from kit over belt. Align the holes in guard with mounting lugs on rear fork. Install acorn bolt (9) through mounting lug and fasten to belt guard. Finger tighten only. 2. Install screw (4) with washer (5, from kit) through belt guard and fasten to threaded mounting lug. Position the guard for adequate clearance and finger tighten screw. 3. At the upper belt guard, install the original forward hex bolt (2) and original washer (3) through the upper guard (1), then through the upper hole in chrome belt guard and through mounting lug on rear fork. Secure with original acorn nut. 4. Tighten all hardware to 110 in-lbs (12.4 Nm)

Related Item : Lower Belt Guard roadliner (1)replace lower belt guard 99 hd softail (1)what kind of screws can i use for a lower belt for my sportster (1)