how to adjust yamaha ttr 125 carburetor

You search Auto repair manual PDF how to adjust yamaha ttr 125 carburetor, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to adjust yamaha ttr 125 carburetor Direct Download speed 5282 Kb/s

  how to adjust yamaha ttr 125 carburetor Full Version speed 6162 Kb/s



Adjusting the Pekar K68 for Dnepr or Ural

0

Filed Under (Tips and Review) by admin on 11-11-2010

download
1. Make sure the ignition timing is correct 2. Adjust the valves as necessary to ensure proper operation 3. Run the engine to warm it up a bit 4. Adjust the float setting. To do this, remove the carburetors (leave the throttle cables attached), remove the bowl and turn the carburetor upside down (fuel will spill). The float should look like this: Adjust as necessary by bending the float support (#37 in Figure 1). Reinstall Installation and idle adjustment 1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns. * Starting using the K68′s (cold weather) 1. Verify fuel flow. Apply choke (pull 52 in Fig1). 2. Using the ticklers (13) allow fuel to enter the bowl until fuel drains from (14) 3. With the ignition off, kick 1 or 2 times 4. Turn ignition on, and as soon as engine is warmed up (maybe sooner) push choke mechanisms to open choke Idle Adjustment (engine running and warm) 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ¼ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

Ural carburetors Installation and idle adjustment

0

Filed Under (Ural) by admin on 02-11-2010

download
1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ¼ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

YAMAHA TTR 125 SHOCKS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 08-01-2012

download
1. With the bike unloaded on the side stand and the shock fully extended, have an assistant measure from a point at the axle (center point) to a point on the frame, fender or bodywork directly above it. Record this measurement. 2. With the bike off the stand and the rider in the seat, bounce on the suspension and let the bike settle. Have the assistant measure from the same two points. Subtract the second measurement from the first. 3. The amount of settle, or “sag” is a function of the wheel travel. It should only be between 1/4 and 1/3 of the total travel. 4. If the difference is less than the minimum, reduce the spring preload. Measure the distance again starting with Step 2. Adjust again if necessary. 5. If the difference is more than the maximum, increase the spring preload. Measure the distance again starting with Step 2. Adjust again if necessary. Note: If the ride height is too low, the shock will bottom unnecessarily, resulting in a harsh ride. If the ride height is too high, the shock will “top out” too easily when rebounding from a bump or under hard deceleration. NITROGEN PRESSURES IN EMULSION SHOCKS CAUTION: The pressure in these shocks cannot successfully be checked. Concerns with the gauge volume and the gas volume in the shock body create a situation where you cannot accurately determine what pressure was in the shock. In addition when the pressure is lowered (i.e. checking the pressure) the gas and some of the shock oil escapes into the gauge. It is possible to lose a large percentage of the shock oil by depressing the core of a charged shock to the atmosphere. Please note that in order to check the pressure, some of the gas must escape and fill the gauge assembly. The volume of the gas pocket is about half the size of your thumb, so a very small volume change results in a large pressure drop. Because the gauges’ volumes vary, it is not possible to deduce the actual pressure in the shock prior to attaching the gauge. Therefore it is imperative that any attempt to check pressure be accompanied by the capability of refilling the shock. In other words: If you don’t have a nitrogen source handy, don’t check the pressure

HSR Carburetor Total Kits Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Intake Manifold: 1. Install MAP sensor in Mikuni manifold (Twin Cam only). 2. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 3. Attach the rubber flange to the Mikuni manifold with the furnished 5/16″x3/4″ bolts and washers. Choke Cables: Mikuni & Harley-Davidson Route the cable with largest radius bends possible. Check the cable for free-play after installation. If there is no free-play, the engine may run rich and deliver poor performance or low fuel mileage. Harley Cable (Twin Cam Kits: 42-19, 45-4) : 1. Remove the Harley choke cable from the stock carb. 2. Remove the spring and plunger from the cable. 3. Remove the spring and plunger from the Mikuni. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut (See Figure 1). Total Kit Installation Instructions The HSR series carburetors are precise yet durable instruments; however, like any other piece of fine equipment, they require correct installation and reasonable care to assure optimum performance and long life. Extra time spent during installation will pay off in both short and long term performance and reliability. This Mikuni HSR carburetor kit is designed to be a bolt-on application, and as such, is set-up and jetted properly for most applications. However, since Harley-Davidson motors are often highly modified, alternate tuning settings may be required. The Mikuni Tuning Manual helps make jetting alterations and adjustments an easy matter. NOTE: Carburetor Kits not designated as C.A.R.B. exempt, are not legal for motor vehicles operated on public highways in the state of California, or in any other states and countries where similar laws apply. WARNING NOTE: NOTE: WARNING CAUTION NOTE: NOTE: TK-2 6. Install the new assembly into the Mikuni carburetor. Be careful to only gently tighten the plastic nut. 7. Loosen the knurled plastic friction nut behind the choke knob and check for free-play (see Figure 2). Figure 1: Harley nut with Mikuni spring & plunger Figure 2: Choke cable adjustments Mikuni Cable (Evo Kits: 42-8, 45-2 & 45-3) : 1. Remove nut, spring and plunger from the Mikuni. 2. Install the nut, spring and plunger onto the cable. 3. Install the assembly into the Mikuni HSR carburetor. Be careful to only gently tighten the plastic nut. 4. Check for free-play. Adjust the cable as necessary. An optional choke cable mounting bracket is included in the Evo kits for custom installations. Carburetor Installation: 1. Insert the carb fully into the rubber flange, align with engine and tighten the clamp. 2. Slip the fuel hose onto the carburetor’s fuel fitting and secure with the enclosed hose clamp. NOTE: Some Twin Cam installations may require removal of a small amount of fin material from the cylinders to clear the float bowl. Throttle Cables The HSR carburetor uses stock 1990 and later Harley- Davidson cables. However, if your Harley is fitted with some other carburetor, you may need to purchase a set of cables. See your dealer for the correct cable set. 1. Route the throttle cables with large radius curves and so they do not interfere with other components. 2. Screw the cable adjusters together to make them as short as possible. 3. Connect the “close” cable first (see Figure 3). 4. Install the “open” cable next (see Figure 3). 5. Adjust the opening cable until the slide can be opened fully. Snug the adjuster lock nut. 6. Turn the handlebar to the right and adjust the throttle free-play with the closing cable adjuster to approximately 1/8″ (see Figure 4)

YAMAHA RAPTOR 350 Removing stock carburetor and cables

0

Filed Under (Yamaha) by admin on 18-01-2012

download
remove seat and gas tank. Make sure fuel petcock is in “off” position. 2. Remove throttle cable paying close attention to routing, as the new cable (s) will need too be routed the same. 3. Remove stock carburetor and stock throttle housing. Stuff a clean, dry rag into manifold to keep debris out of motor. 4. Remove stock air box. 5. Remove choke cable from handlebars. 6. Remove carb vent line from bike. Carburetor installation 1. Carefully trim the rubber alignment tab off of the face of the manifold with a razor blade or side cutters. 2. Remove the hex pipe plug from the carb cap using a 11mm or 7/16 wrench. Do not discard plug, as it will be needed later. Install the metering adjustment tool included in the hardware kit. Do not over-tighten as damage may occur to cap. 3. Attach fuel line to carburetor and secure with clamp. 4. Install remote idle cable into tab on top of carburetor. See main manual for this step. NOTE: Nut must be removed from cable before installation 5. Place carburetor into manifold

Related Item : yamaha raptor 3wire key ignicion conection diagram (2)yamaha breeze carburetor to head parts (1)where is the fuel enrichment plunger on a 2001 raptor 660 (1)where is the carb drain on a zuma (1)virago 750 factory carb settings (1)tt125 bowl (1)TK1 carburretor diagram (1)stock carburetor adjustments for 1996 yamaha fzr600r (1)replace a jet on a tt125 (1)removing the carburator on a 2004 wr250f (1)