how to bleed a cooling system on kawaski mule

You search Auto repair manual PDF how to bleed a cooling system on kawaski mule, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to bleed a cooling system on kawaski mule Direct Download speed 5282 Kb/s

  how to bleed a cooling system on kawaski mule Full Version speed 6162 Kb/s



2003 SUZUKI SV 650 COOLING AND LUBRICATION SYSTEM SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
COOLING CIRCUIT INSPECTION Before removing the radiator and draining the engine coolant, inspect the cooling circuit for tightness. • * Remove the cowling. (SV650S) (C-7–7-6) • * Loosen the radiator cap stop screw 10 . (SV650) • * Remove the radiator cap O2 and connect the radiator tester to the filler. A WARNING Do not remove the radiator cap when the engine is hot. • * Give a pressure of about 120 kPa (1 .2 kgf/cm2,17.0 psi) and see if the system holds this pressure for 10 seconds . • * If the pressure should fall during this 10-second interval, it means that there is a leaking point in the system . In such a case, inspect the entire system and replace the leaking component or part. A WARNING When removing the radiator cap tester, put a rag on the filler to prevent spouting of engine coolant. CAUTION Do not allow the pressure to exceed specified pressure, or the radiator can be damaged. COOLING AND LUBRICATION SYSTEM 6-3 6-4COOLING AND LUBRICATION SYSTEM RADIATOR REMOVAL • * Remove the cowling. (SV650S) ( r- 7-7-6) • * Drain engine coolant. (r– 72-20) • * Disconnect the right and left radiator hoses from the radiator. • * Disconnect the siphon hose from the radiator. • * Disconnect the horn lead wires. rI .rr • * Remove the radiator lower mounting bolt. • * Disconnect the cooling fan motor and its thermo-switch lead wire coupler 10. • * Remove the radiator by upper mounting bolt. • * Remove the cooling fan. • * Disconnect the cooling fan thermo-switch. • * Remove the cooling fan thermo-switch. • * Remove the horn. CAUTION When removing the horn, hold the nut by spanner to prevent the horn bracket distortion. COOLING AND LUBRICATION SYSTEM 6-5 INSTALLATION • * Install the cooling fan and horn. 0 Cooling fan/horn mounting bolt: 8 N .m (0.8 kgf-m, 6 .0 Ib-ft) • * Install the cooling fan thermo-switch. ( l”76-9) • * Install the siphon hose to the radiator. • * Install the radiator in the reverse order of removal. • * Route the radiator hoses properly. (=9-22) 9-22) • * Install the drain plug with a new sealing washer and pour engine coolant. (=2-20) • * Bleed air from the cooling circuit. (r– 72-21) • * Install the cowling. (SV650S)

Incoming search terms:

Suzuki SV1000 COOLING AND LUBRICATION SYSTEM REPAIR MANUAL

0

Filed Under (Suzuki) by admin on 25-02-2011

download
At the time of manufacture, the cooling system is filled with a 50 :50 mixture of distilled water and ethylene glycol anti-freeze . This 50:50 mixture will provide the optimum corrosion protection and excellent heat protection, and will protect the cooling system from freezing at temperatures above -31 °C (-24 °F) . If the motorcycle is to be exposed to temperatures below -31 °C (-24 °F), this mixing ratio should be increased up to 55 % or 60 % according to the figure. CAUTION • Use a high quality ethylene glycol base anti-freeze, mixed with distilled water . Do not mix an alcohol base anti-freeze and different brands of anti-freeze. • Do not rut in more than 60%anti-freeze or less than 50 %. (Refer to the right figure.) • * Do not use a radiator anti-leak additive. A WARNING COOLING AND LUBRICATION SYSTEM 5-3 20 40 60 80100 0 10 20 30 40 50 60 Density (%) Fig .2 Engine coolant density-boiling point curve • * You can be injured by scalding fluid or steam if you open the radiator cap when the engine is hot . After the engine cools, wrap a thick cloth around cap and carefully remove the cap by turning it a quarter turn to allow pressure to escape and then turn the cap all the way off . • * The engine must be cool before servicing the cooling system . • * Coolant is farmful; • * If the comes in contact with skin or eyes, flush with water. • * If swallowed accidentally, induce vomiting and call physician immediately . • * Keep it away from children . Anti-freeze density Freezing point 50% -31 °C (-24 °F) 55% -40 °C (-40 °F) 60% -55 °C (-67 °F) 50 % engine coolant including reservoir tank capacity Anti-freeze 1 100 ml (2.3/1 .9 US/Imp-pt) Water 1 100 ml (2.3/1.9 US/Imp.pt) Density (%) Fig.1 Engine coolant density-freezing point curve (°F) (°C) 302 150 (kgf/cm2) 284 140 1.5 c Q 266 130 0.9 0) a) :0 248 120 0.5 0) m Z3 230 110 0 (7 212 100 (F) (C) 32 0 14 -10 -4 -20 C 0 Q -22 -30 O) C N -40 -40 a) a) U- -58 -50 -76 -60 -94 -70 5-4 COOLING AND LUBRICATION SYSTEM COOLING CIRCUIT THERMOSTAT RESERVOIR TANK RADIATOR NO. 1 CYLINDER HEAD NO . 1 CYLINDER NO. 2 CYLINDER NO. 2 CYLINDER HEAD WATER PUMP INSPECTION Before removing the radiator and draining engine coolant, inspect the cooling circuit for tightness. • * Remove the body cowling. (=6-6) • * Remove the radiator cap ® . • * Connect the tester 02 to the filler. A WARNING Do not remove the radiator cap when the engine is hot. • * Give a pressure of about 110 kPa (1.1 kgf/cm 2, 15 .6 psi) and see if the system holds this pressure for 10 seconds. • * If the pressure should fall during this 10-second interval, it means that there is a leaking point in the system. In such a case, inspect the entire system and replace the leaking component or part. A WARNING When removing the radiator cap tester, put a rag on the filler to prevent spouting of engine coolant. CAUTION Do not allow the pressure to exceed the radiator cap release pressure, or the radiator can be damaged

Kawasaki Mule Lift Kit Installation Manual

0

Filed Under (Kawasaki) by admin on 04-05-2012

download
Front Lift Installation 1. Ensuring that the parking brake is set, place jack under center of the Mule front end and lift until front wheels clear the ground. Be careful to support Mule properly so that it is secure, but so that the A-arms and struts can droop to full extension. 2. Remove front wheels. 3. If applicable, remove the heater to allow access to the strut mount behind the heater coil. Heater 4. Starting with the left side (driver side), remove the cotter pin and castle nut that secures the strut to the strut mount. Castle Nut & Pen 5. Push bolt through the bolthole, taking care not to damage the brake line that is attached to the bolt. If you are having difficulty removing the bolt, you may have to remove the brake lines that are attached to the front brakes. In this case refer to owners manual for removing brake lines. Screwdriver NOTE: Keep in mind that if you remove the brake lines you must bleed your brakes according to operator’s manual. 6. Once the bottom of the strut has been loosened, then unbolt the top of the strut. The nuts securing the top strut can be located in the dash of the Mule on the left and right sides. In most cases these nuts are easily accessible, but you may have to remove the glove box or heater coils, depending on the model and options purchased with the Mule.

Incoming search terms:

SUZUKI SV650 COOLING AND LUBRICATION SYSTEM

0

Filed Under (Suzuki) by admin on 04-12-2010

download
ENGINE COOLANT At the time of manufacture, the cooling system is filled with a 50:50 mixture of distilled water and ethylene glycol anti-freeze. This 50:50 mixture will provide the optimum corrosion protection and excellent heat protection, and will protect the cooling system from freezing at temperatures above -31 °C (-24 °F) . If the motorcycle is to be exposed to temperatures below -31 °C (-24 °F), this mixing ratio should be increased up to 55 % or 60 according to the figure. A WARNING 204060 80100 Density (%) .. • * You can be injured by scalding fluid or steam if you open the radiator cap when the engine is hot. After the engine cools, wrap a thick cloth around cap and carefully remove the cap by turning it a quarter turn to allow pressure to escape and then turn the cap all the way off . * The engine must be cool before servicing the cooling system. • * Coolant is harmful ; • * If it comes in contact with skin or eyes, flush with water. • * If swallowed accidentally, induce vomiting and call physician immediately. • * Keep it away from children.

Kawasaki Mule Roof 600, 610 and 4010 Trans Crew, Roof Installation Manual

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
INSTALLTION INSTRUCTIONS – Mule 600/610 (4010 Trans skip to pg 4) 1. Place Roof Panel on top of UTV Roll cage and center front to back, and left to right. 2. Using Figure 1 Below – place UTV Roof Mounting Brackets around roll cage bar and using a marker, mark the position of the holes needed in the roof for each Roof Mounting bracket . Figure 1 Copyright 2007 DiamondBack Automotive Accessories, Inc. Page 3 3. Next, remove the roof from the roll cage and using a drill with 1/4″ bit, drill holes using the marks as a guide. 4. Cut (4) 3″ strips of adhesive foam and apply to roof in where mounting brackets are positioned to prevent roof rattling once mounted. Foam should run in the direction of the roll cage as shown in Figure 1 above. 5. Next, reposition the roof on the roll cage according to step 1. 6. Prior to attaching the roof mount brackets, cut the remaining adhesive foam in half and apply one section to the roof in the center of the roof where roof and each roll cage bar meet as shown in Figures 1 above. If additional tape is required to prevent rattling it can be purchased from any hardware store as window sealant foam tape. 7. Next, attach the roof mount brackets according to Figure 2. Use channel locks or pliers to hold top of carriage bolt and turn nut with 7/16″ socket.

Incoming search terms:

2005-2007 Kawasaki 610 Mule Winch Mount Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the plastic lower front cover. 2. Remove the two bolts on the left side mud shield that connect to the frame for easier access. 3. Install the winch to the winch mount using the hardware supplied with the winch. 4. Install the winch and mount per the illustration using the provided U-Bolts, flat washers and nuts around the frame tubes and through the mount. Tighten all nuts and bolts securely. 5. Install the roller fairlead to the winch mount using (2) 5/16″ x 3/4″ bolts and 5/16″ nylock nuts provided. (Rollers should turn freely. NOTE: Bottom roller may need to be removed to run wire rope through. 6. Using the instructions provided with the winch, wire accordingly. 7. Reinstall the two bolts from the mud shield. 8. Reinstall the plastic lower front cover. NOTE: For some winches, this cover may need to be trimmed so it does not rub

Incoming search terms:

Kawasaki Mule 610 Without coil springs Installation

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1.)Begin by loosening the lug nuts on both front tires. Raise the unit, using a suitable lifting device or procedure, until the front tires are off the ground. If using a floor jack with stands, chock the rear wheels to prevent the unit from rolling. If using jack stands, make sure the stands are placed under the frame and not the body. Make sure the unit is stable and secure . 2.)Remove the tires / wheels. NOTE: Now is a good time to check the threads on the lug studs. Check for rust, pulled threads or other deterioration that could cause a stud/thread failure. 3.) The first thing to do is remove the front cowl and trunk on the bike. You can accomplish this by removing all the bolts (screws) around the perimeter of the cowl and removing some plastic “snap rivets”. To remove the rivets simply pull the center section up and then the rest will follow. 4.)Place a floor jack, or other suitable device, beneath the left side lower control arm. This is to prevent damage to the tie rod or slip yoke boot while disassembling the lower control arm and strut. Using a 14mm socket, remove the two retaining nuts and lock washers on the top of the struts. 5.)Leaning the strut forward toward the headlamp buckets will put the strut in position to allow you to reach over the top and place the strut spacer in place. Install the strut spacer on top of the coil retainer and tightening the nuts. Install the supplied gasket on top of the strut spacer, and re-install the strut assembly

Kawasaki MULE 600 / 610 SNOW PLOW INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. PRELIMINARY: 1.1 Remove the six 6 mm. screws and plastic skid / splash shield from the bottom front of the vehicle frame. (These bolts and plastic skid / splash shield will not be reused snow plow mounting frame installed onto the vehicle.) 1.2 If the vehicle has the Kawasaki optional brush guard installed, it will have to be removed and then reinstalled after the snow plow mounting frame is installed. (The brush guard will fit with the snow plow mounting frame installed first.) 2. VEHICLE MOUNTING FRAME 2.1 Position the vehicle mounting frame (13) under the front of the vehicle so that the six holes (with pipe spacers) line up with the six 6 mm. threaded holes that the plastic skid / splash shield was attached with and the upper plate is through the large oval hole in the vehicle plastic fascia. Fasten loosely using 6mm. x 1.0mm. x 30mm. bolts (33) , 6mm. lock washers (35) and 6mm. flat washers (34). 2.2 Place a 5/16″-18 “U” bolt (36) around the front cross tube behind the plastic fascia and through each set of holes in the flange of the upper plate of the vehicle mounting frame (total of two “U” bolts). Fasten loosely using 5/16″flat washers (41), 5/16″ lock washers (40), and 5/16″-18 nuts (42). 2.3 Install a 5/16″-18 “U” bolt (36) around the lower frame tubes and through each set of slotted holes in the lower plate of the vehicle mounting frame (total of four “U” bolts). Fasten loosely using 5/16″ flat washers (41), 5/16″ lock washers (40), and 5/16″-18 nuts (42). 2.4 Tighten all the fasteners holding the vehicle mounting frame to the vehicle starting with the 6mm. bolts

Incoming search terms:

Kawasaki Mule Duster Adhesive Hook Strip Installation Instructions

0

Filed Under (Kawasaki) by admin on 30-04-2012

download
Use the loop on the Duster as a guide to locate the Hook Strip on the front of the bed. Clean the area and install the Adhesive Hook Strip as in Step 1. Install Adhesive Hook Strip to Front of Bed Cut the Adhesive Hook Strip into six (6) pieces to match the loop sewn to the Duster. Use the loop on the Duster as a guide to locate the Hook Strip on the sides of the bed and the tailgate. Clean the areas with a 50% Water/Alcohol Solution. Peel the backing off the hook a little at a time and press it fi rmly into place. Install Adhesive Hook Strip Allow 72 hours for the adhesive to set. Avoid unnecessary fastening and unfastening of the Duster during this period. Open Bed Open the bed of the vehicle. Tailgate Adhesive Hook Strip Allow 72 hours for the adhesive to set. Avoid unnecessary fastening and unfastening of the Duster during this period. Secure Duster to Front of Bed Fasten the loop sewn to the front of the Duster to the Adhesive Hook Strip on the front of the bed

Incoming search terms:

Kawasaki Mule 3010 Hood Rack Installation And Operations Manual

0

Filed Under (Kawasaki) by admin on 28-04-2012

download
1. Install the Seizmik Brush Guard. – Have a friend hold the brush guard (G) in place while you slide the 1.0″ dia. tube clamps (K) in place over the middle tube of the OEM bumper, as shown in Figure 1. Secure each one in place with one of the 3/8″ x 2.25″ bolts (N), two 3/8″ washers (Q), and one 3/8″ nylock nut (R). Repeat at the top tube of the OEM bumper using the 1.5″ dia. tube clamps (J), and 3/8″ x 1.75″ bolts (O). VEHICLE FRONT Figure 2. 2. Mounting brackets – Attach the two hood rack mounting brackets to the mounting pads of the brush guard, as shown in Figure 2. Use four of the 3/8″ x 1.0″ bolts (P), eight 3/8″ washers (Q), and four 3/8″ nylock nuts (R) per mounting pad. Snug down the fasteners but do not fully tighten them yet. 3 Figure 3. 3. Crush sleeves – Insert a crush sleeve (B) into each cantilever arm assembly (C & D), as shown in Figure 3. 4. Cantilever arms – Position the Driver side cantilever arm (C) on the mounting bracket, and insert a 3/8″ dia. pivot bolt (M), as shown in Figure 4. Add a 3/8″ washer (Q) and nylock nut (R) on the other side and snug down the assembly; leave the fasteners loose enough so the components can be repositioned for fitment. Repeat this step for the passenger side. Figure 4. 4 Figure 5. 5. Lock pins – Insert the 1/2″ lock pins (Y) into the tabs on each side of the Brush Guard, fixing the cantilever arms in place, as shown in Figure 5.

Incoming search terms:

Incoming search terms: