how to bleed radiator on a 2003 ktm dirtbike

You search Auto repair manual PDF how to bleed radiator on a 2003 ktm dirtbike, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to bleed radiator on a 2003 ktm dirtbike Direct Download speed 5282 Kb/s

  how to bleed radiator on a 2003 ktm dirtbike Full Version speed 6162 Kb/s



2003 SUZUKI SV 650 COOLING AND LUBRICATION SYSTEM SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
COOLING CIRCUIT INSPECTION Before removing the radiator and draining the engine coolant, inspect the cooling circuit for tightness. • * Remove the cowling. (SV650S) (C-7–7-6) • * Loosen the radiator cap stop screw 10 . (SV650) • * Remove the radiator cap O2 and connect the radiator tester to the filler. A WARNING Do not remove the radiator cap when the engine is hot. • * Give a pressure of about 120 kPa (1 .2 kgf/cm2,17.0 psi) and see if the system holds this pressure for 10 seconds . • * If the pressure should fall during this 10-second interval, it means that there is a leaking point in the system . In such a case, inspect the entire system and replace the leaking component or part. A WARNING When removing the radiator cap tester, put a rag on the filler to prevent spouting of engine coolant. CAUTION Do not allow the pressure to exceed specified pressure, or the radiator can be damaged. COOLING AND LUBRICATION SYSTEM 6-3 6-4COOLING AND LUBRICATION SYSTEM RADIATOR REMOVAL • * Remove the cowling. (SV650S) ( r- 7-7-6) • * Drain engine coolant. (r– 72-20) • * Disconnect the right and left radiator hoses from the radiator. • * Disconnect the siphon hose from the radiator. • * Disconnect the horn lead wires. rI .rr • * Remove the radiator lower mounting bolt. • * Disconnect the cooling fan motor and its thermo-switch lead wire coupler 10. • * Remove the radiator by upper mounting bolt. • * Remove the cooling fan. • * Disconnect the cooling fan thermo-switch. • * Remove the cooling fan thermo-switch. • * Remove the horn. CAUTION When removing the horn, hold the nut by spanner to prevent the horn bracket distortion. COOLING AND LUBRICATION SYSTEM 6-5 INSTALLATION • * Install the cooling fan and horn. 0 Cooling fan/horn mounting bolt: 8 N .m (0.8 kgf-m, 6 .0 Ib-ft) • * Install the cooling fan thermo-switch. ( l”76-9) • * Install the siphon hose to the radiator. • * Install the radiator in the reverse order of removal. • * Route the radiator hoses properly. (=9-22) 9-22) • * Install the drain plug with a new sealing washer and pour engine coolant. (=2-20) • * Bleed air from the cooling circuit. (r– 72-21) • * Install the cowling. (SV650S)

Incoming search terms:

2000-2003 KTM MXC / EXC Dual Sport Kit Installation And Removal Manual

0

Filed Under (KTM) by admin on 08-02-2012

download
00-’03 KTM 400/450/520/525 EXC & MXC Dual Sport Kit Installation Manual 1. Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the seat, fuel tank, and side panels. Stock switch Bracket Photo 2 EXC – Unplug and remove the stock headlight. (Photo 2.) Unplug the stock three-pin taillight connector and pull the taillight wires back to the rear of the airbox temporarily. MXC – Remove the stock front number plate. 3. Make sure the stock battery is oriented in its mounting bracket as shown with the positive terminal on the left side of the bike (as viewed if sitting on the bike). If not, remove and spin it 180 degrees. Photo 3
4. MXC ONLY! (EXC skip this step.) Locate the stock lighting wiring harness zip-tied under the frame back-bone (See Photo 4). Remove the securing zip-ties and route this wiring forward to the area behind the headlight. Route along right side of frame using factory wire- guide clamp. 5. Brake Light Switch Installation: The KTM kit uses a hydraulic brake-switch. This requires replacing the rear master cylinder banjo bolt with a specially made switch. Installing the switch requires bleeding the brake. If you do not feel competent bleeding your rear brake, please refer this job to a qualified mechanic, as failure to do it correctly will make the brake inoperable. Remove the stock banjo bolt and replace with the hydraulic switch as shown. Make sure to install

Cobra JR/ OI Radiator with Louvers Replacement

0

Filed Under (Cobra) by admin on 10-11-2010

download
The 2009 model year radiator for Cobra JR (also remaining OI ) model will be FCCJ0004 which now has provisions for louvers. On the 2009 models these louvers also rely on a feature on the frame down-tube for mounting the plastic louvers. Older models do not have these features on the frame and so it is not possible to utilize the louver mounts on the radiator. Customers with older models JR/CM or OI/P3/PW3 needing a replacement radiator for ECMU0061 or ECMU0225 will be sold a radiator kit FKMU0001 which includes the new style radiator, FCCJ0004C (with louver mounting tabs removed), and all mounting hardware. This will allow the mounting of the new style radiator onto these products without mounting the louvers. As the 2009 frame is now the service replacement frame for JR/CM & OI/PW3/P3 models from 2004 – 2008, the louvers are able to mount on all older models JR/CM & OI/PW3/P3 that have the appropriate mounting provisions. Welding on the highly stressed down-tube frame member is not recommended by Cobra because it can cause premature structural failure to the frame and possible injury to the rider.

2000-2003 KTM MXC / EXC Dual Sport Kit Installation Manual

0

Filed Under (KTM) by admin on 01-02-2012

download
Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the seat, fuel tank, and side panels. Stock switch Bracket Photo 2 EXC – Unplug and remove the stock headlight. (Photo 2.) Unplug the stock three-pin taillight connector and pull the taillight wires back to the rear of the airbox temporarily. MXC – Remove the stock front number plate. 3. Make sure the stock battery is oriented in its mounting bracket as shown with the positive terminal on the left side of the bike (as viewed if sitting on the bike). If not, remove and spin it 180 degrees. Photo 3 4. MXC ONLY! (EXC skip this step.) Locate the stock lighting wiring harness zip-tied under the frame back-bone (See Photo 4). Remove the securing zip-ties and route this wiring forward to the area behind the headlight. Route along right side of frame using factory wire- guide clamp. 5. Brake Light Switch Installation: The KTM kit uses a hydraulic brake-switch. This requires replacing the rear master cylinder banjo bolt with a specially made switch. Installing the switch requires bleeding the brake. If you do not feel competent bleeding your rear brake, please refer this job to a qualified mechanic, as failure to do it correctly will make the brake inoperable. Remove the stock banjo bolt and replace with the hydraulic switch as shown. Make sure to install

KTM KINETO TRACKING MOUNT – MODEL K433 Installation and Removal Manual

0

Filed Under (KTM) by admin on 30-01-2012

download
the KTM meets the needs of a wide variety of test range and scientific applications:  On-board operator, or remote analog or digital control  Payloads up to 1200 pounds (unmanned) or 600 pounds (manned)  Mission configuration with four (manned) or six (unmanned) payload positions  Complete turnkey systems available  Detailed installation documentation FIELD-PROVEN RUGGED AND RELIABLE The KTM consistently demonstrates its performance and durability:  Weather tight seals designed to withstand harsh range environments  The KTM’s direct drive axis design delivers smooth, jitterfree tracking to ensure precise Time, Space and Position Information (TSPI)  Self-contained and trailer-mounted, the KTM is quickly and easily deployed via highway and unimproved roads to remote tracking sites  Digital Control System (DCS) that guarentees system reliability WHEN THE RANGES REQUIRED PRECISE AND RELIABLE OPTICAL TRACKING MOUNTS, THEY SELECTED THE BRASHEAR KINETO TRACKING MOUNT MORE THAN 150 TIMES. Recognized Standard for Tracking Systems Worldwide THE KTM DIGITAL CONTROL SYSTEM (DCS) INCLUDES:  High speed communication via an Ethernet interface to provide remote operation  Advanced servo loop control to optimize tracking performance  Built-in error correction to ensure precision tracking accuracy  Versatile chassis architecture that accommodates additional PC104 cards suchas an “Automatic Video Tracker” (AVT) to satisfy specific customer requirements and missions

Incoming search terms:

2003 – 2006 KTM The e-Axle Installation Manuals

0

Filed Under (KTM) by admin on 01-02-2012

download
Remove the stock wheel spacers from both sides of the wheel hub and install both of the Rekluse wheel spacers. After installing the Rekluse wheel spacers, stow the wheel in a suitable place so that the brake rotor cannot be damaged. See following picture. 5 5. Remove the brake pads by removing the clips and sliding out the pin. See following picture. 6. Remove the leaf spring from the caliper. See following picture. 7. Re-install the brake pads with the included coil spring positioned on the pin between the brake pads. Secure the pin by re-installing the 2 clips. See following picture. Coil Spring on the pin and in between the brake pads 6 8. Coat the center axle in a thin layer of grease to aid in sliding the center axle on and off. Note: Coat the center axle in a thin layer every time it is reinstalled after removing the front wheel for tire maintenance. 9. Position the front wheel back in between the forks so that the brake disk is in place between the brake pads, and so the wheel spacers line up with the hole in the fork fists. 10. Slide the center axle, with 30-mm Bushing attached, through the right-side fork fist and through the wheel spacers in the front hub. Rotate the 30-mm bushing so the set screw is facing up, this will line the “0″ Offset Mark with the fork fist pinch clamp slot. Continue sliding the axle through until the 30-mm bushing is almost flush with the outer edge of the right fork fist. See following picture

2003 KTM RA 250 SX REPAIR MANUAL ENGINE

0

Filed Under (KTM) by admin on 08-02-2012

download
STORING THE REPAIR MANUAL IN THE BINDER -Put the index into the binder. -Put the front page of the repair manual (210×297 mm) into the transparent pocket provided for this purpose on the outside of the binder. -Put the spine label (170×45 mm) into the transparent pocket provided for this purpose on the spine of the binder. -Put the summary list of contents (150×297 mm) into the transparent pocket provided for this purpose on the inside of the binder or insert this page on the beginning of the manual. -Then insert the individual chapters of the manual between the sheets of the index according to the page number printed in the right bottom corner of each page. Example: page no. 3-5 3 = chapter 3 5 = page 5 All pages with a page number that begins with the digit 3, for example, must be put under the index heading „Chapter 3″. -Index sheets that have not been marked with a certain chapter are for your personal convenience. T he respective headings can be entered in the list of contents

2001 – 2003 Prius 2003 4Runner, Camry, Land Cruiser and Sequoia VEHICLES EQUIPPED WITH TRANSPONDER ECU

0

Filed Under (Toyota Manuals) by admin on 07-10-2011

download
When replacing the ECM (SAE term: PCM) or the Transponder ECU a “handshake” procedure must be performed. This ECU ID communication is necessary to enable the Transponder ECU and the ECM to recognize each other before the vehicle will start. Complete ECU communication using the following steps: 1. Insert a Master key into the ignition cylinder. 2. Turn the ignition ON (engine OFF). 3. Short Tc and CG terminals of DLC3 using the Diagnostic Check Wire (SST 09843-18020 or equivalent) and leave for 30 minutes. 4. After 30 minutes, turn the ignition OFF and remove check wire from DLC3. 5. Register any additional keys as necessary. 6. Start the vehicle to confirm successful ECU communication. Key Programming: To program or delete a key, a registered Master key is necessary unless the Transponder ECU has been reset or replaced. The Transponder ECU system incorporates a black “Master” key and a gray “Sub” key. The process during registration of these two keys is identical. The key itself now determines if it functions as Master or Sub, not the registration procedure. The maximum number of allowable Master and Sub keys vary by model. Refer to the chart below.

Incoming search terms:

Suzuki SV1000 COOLING AND LUBRICATION SYSTEM REPAIR MANUAL

0

Filed Under (Suzuki) by admin on 25-02-2011

download
At the time of manufacture, the cooling system is filled with a 50 :50 mixture of distilled water and ethylene glycol anti-freeze . This 50:50 mixture will provide the optimum corrosion protection and excellent heat protection, and will protect the cooling system from freezing at temperatures above -31 °C (-24 °F) . If the motorcycle is to be exposed to temperatures below -31 °C (-24 °F), this mixing ratio should be increased up to 55 % or 60 % according to the figure. CAUTION • Use a high quality ethylene glycol base anti-freeze, mixed with distilled water . Do not mix an alcohol base anti-freeze and different brands of anti-freeze. • Do not rut in more than 60%anti-freeze or less than 50 %. (Refer to the right figure.) • * Do not use a radiator anti-leak additive. A WARNING COOLING AND LUBRICATION SYSTEM 5-3 20 40 60 80100 0 10 20 30 40 50 60 Density (%) Fig .2 Engine coolant density-boiling point curve • * You can be injured by scalding fluid or steam if you open the radiator cap when the engine is hot . After the engine cools, wrap a thick cloth around cap and carefully remove the cap by turning it a quarter turn to allow pressure to escape and then turn the cap all the way off . • * The engine must be cool before servicing the cooling system . • * Coolant is farmful; • * If the comes in contact with skin or eyes, flush with water. • * If swallowed accidentally, induce vomiting and call physician immediately . • * Keep it away from children . Anti-freeze density Freezing point 50% -31 °C (-24 °F) 55% -40 °C (-40 °F) 60% -55 °C (-67 °F) 50 % engine coolant including reservoir tank capacity Anti-freeze 1 100 ml (2.3/1 .9 US/Imp-pt) Water 1 100 ml (2.3/1.9 US/Imp.pt) Density (%) Fig.1 Engine coolant density-freezing point curve (°F) (°C) 302 150 (kgf/cm2) 284 140 1.5 c Q 266 130 0.9 0) a) :0 248 120 0.5 0) m Z3 230 110 0 (7 212 100 (F) (C) 32 0 14 -10 -4 -20 C 0 Q -22 -30 O) C N -40 -40 a) a) U- -58 -50 -76 -60 -94 -70 5-4 COOLING AND LUBRICATION SYSTEM COOLING CIRCUIT THERMOSTAT RESERVOIR TANK RADIATOR NO. 1 CYLINDER HEAD NO . 1 CYLINDER NO. 2 CYLINDER NO. 2 CYLINDER HEAD WATER PUMP INSPECTION Before removing the radiator and draining engine coolant, inspect the cooling circuit for tightness. • * Remove the body cowling. (=6-6) • * Remove the radiator cap ® . • * Connect the tester 02 to the filler. A WARNING Do not remove the radiator cap when the engine is hot. • * Give a pressure of about 110 kPa (1.1 kgf/cm 2, 15 .6 psi) and see if the system holds this pressure for 10 seconds. • * If the pressure should fall during this 10-second interval, it means that there is a leaking point in the system. In such a case, inspect the entire system and replace the leaking component or part. A WARNING When removing the radiator cap tester, put a rag on the filler to prevent spouting of engine coolant. CAUTION Do not allow the pressure to exceed the radiator cap release pressure, or the radiator can be damaged

2005-2007 KTM MOTORCYCLE REPAIR MANUAL

0

Filed Under (KTM) by admin on 21-11-2010

download
Adjustments -Take notice of the position of the compression adjustment 1 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -Remove the rubber cap out of the axleclamp. -Take notice of the position of the rebound adjustment 2 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -For the standard position see setting list. Position of the compression and rebound adjustment -Set the rebound position 1 , see KTM-Owners manual. -Assemble the rubber cap. -Set the compression position 2 , see KTM-Owners manual. 1 2 2-22 Repair manual WP Fork “Closed Cartridge” Art.No.: 3.211.199-E Explanation of the spring preload -Total spring length without the spacers, see chapter inspection of the spring! -Spring length with spacers 1 , see setting list. -Spring with the spacers. 1 . -The spring is assembled in the front fork leg. NOTE: the distance of “B” is less then the length of “A”. A – B = Spring preload A 1 1 B 2-23 Air release screw -Place the motorcycle on the stand. NOTE: the front wheel must be lift of the floor! -Unscrew the air release screw 1 of the screw cap on top of the front fork and tighten after approx. 10 seconds the air release screw. Recommended periodic maintenance and inspection of the 4860 SX/SXS/SMR front fork 1 A 100 liter fuel consumption is equivalent to approx. 15 operating hours Clean dust scrapers (after 1 hour) Bleed fork legs regularly – after every cleaning Check the inner tubes on scratches / leakage Visual check of damaging of the outer-tubes / replace if necessary Complete service without disass. the closed cartridge of the fork Complete service including the closed cartridge of the front fork Dismounting the fork -Place your motorcycle on a stand. -Notice the position of the front fork in the triple-clamps. NOTE: To remove the front fork. Read your KTM Instruction Manual or Workshop Manual. 3-3 Mounting the fork -Clean the innerside of the triple-clamps with brake cleaner. -Slide both fork legs into the triple-clamps. NOTE: Pay attention to the position of the fork legs. Standard riding height! NOTE: The maximum riding height is the level of the second groove! -Tighten the middle bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the first bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the third bolt of the lower triple clamp to a torque of 17 Nm!

Incoming search terms:

Incoming search terms: