how to bypass cdi box on suzuki gs500bike

You search Auto repair manual PDF how to bypass cdi box on suzuki gs500bike, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to bypass cdi box on suzuki gs500bike Direct Download speed 5282 Kb/s

  how to bypass cdi box on suzuki gs500bike Full Version speed 6162 Kb/s



Triumph Bonneville America And Speedmaster The Freak Installation Instructions and Parts List

0

Filed Under (Triumph) by admin on 29-10-2010

download
INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. 1. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. A. Seats – Remove both seats starting with the passenger pillion, if applicable. B. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover. Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C . C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box. On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. D. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). E. Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap. Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first. Remove the battery. F. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. G. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector. Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. 2. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. A. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions. B. Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. C. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs. D. Remove the mufflers – Remove the mufflers by loosening the clamp at the exhaust header, and by removing the rear foot peg hangers. If the mufflers are not removed, they can become damaged by the axles in Section 2H . E. Disconnect the carburetors – With a small flathead screwdriver, pull the retainer springs out of the channel of the carburetor intake tubes (the two large black tubes coming from the air box into the back of each carburetor), and simply push them towards the air box off of the carbs

Incoming search terms:

Kawasaki GEN2 CDI Installation And Removal Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Installation: Step 1: Remove the seat to allow access to the factory CDI igniter on the utility machine. See Figure 1. The KFX-700 (V-Force) CDI is located on the right frame rail by the rear tire. The Teryx CDI is located under the driver’s seat, inside the electrical box. See Figure 2. Disconnect the negative battery cable. Locate the stock CDI (located under the seat). Disconnect the connectors from the CDI, and remove the CDI. NOTE: If your machine has had a timing offset key installed (aftermarket equipment), then the timing maps need to be adjusted using the optional USB Memory Interface. The CDI is shipped assuming 5 degrees static timing, and increasing this with an offset key without compensating the maps may lead to engine damage. Figure 1: Figure 2: Step 2: Remove the two #4×4-40 screws from the DB44 connector at the front of the CDI. Plug the Copperhead® wiring harness into the DB44 connector, and secure with the two #4×4-40 screws. The screws should be snug, but do not over tighten. Plug connectors from the Copperhead® CDI to their corresponding connector on the chassis wiring harness. The Copperhead® CDI will be mounted 90 degrees (1/4 turn) from the stock position in most applications. This will allow it to sit between the stock mounting tabs on the pan. See Figure 3 for the BF750i installation and Figure 4 for the Teryx installation. Test fit the unit, and mark the necessary mounting holes. The KFX-700 (V-Force) will require holes to be drilled in the frame to mount the CDI

Incoming search terms:

HARLEY DAVIDSON LOCKING GLOVE BOX DOOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION 1. Unsnap the original equipment (O.E.) left-side glove box door, and unfasten the tether by bringing the aglet end (see Figure 1, B) out through the retaining hole. Always wear proper eye protection when drilling or grinding. Flying debris could cause serious eye injury. (00402e) 2. Using an 3/16 inch (5 mm) bit positioned in the center of each snap, drill out the four plastic snaps surrounding the glove box opening. NOTE The glove box door, hinge and frame assemblies are side- specific. The assemblies install so that the tether retaining hole (C) in the door frame is to the inboard side. 3. Obtain the new left-side glove box door, hinge and frame assembly (1), a lock (2) and a tether assembly (8) from the kit. Remove the nut (3) from the lock. 4. Insert the lock through the hole in the glove box door as shown. Assemble the tether over the lock threads with the tab (A) on the inboard side of the lock, same as the retaining hole in the door frame. Tighten securely. 5. Open the left-side door, and position the door assembly at the glove box opening, lining up the holes. 6. Insert a screw (9) through each of the holes in the door frame and glove box. Install a hex nut with washer (10) onto the threads of each screw. Tighten finger-tight. NOTE Ambient temperature should be at least 60° F (16° C) for proper adhesion of the gaskets to the glove box door frame. 7. Clean the glove box door frame with a mixture of 50 to 70% isopropyl alcohol and 30 to 50% distilled water. Allow to dry thoroughly. NOTE The glove box gaskets are side-specific. With the paper backing facing the door frame, the oblong hole at the top of the gasket is to the outboard side. 8. Obtain the left-side gasket (6) and a hinge gasket (7) from the kit. Install the gaskets to the glove box door frame. a. The gasket liner on the large gasket is split to aid alignment. Peel one half of the liner from the adhesive backing of the left-side gasket. b. Using the frame edges and screw heads as a guide, carefully position the gasket to the glove box door frame and press firmly into place. c. Peel the remaining half of the liner from the gasket backing, and carefully position the rest of the gasket to the door frame. Press firmly into place. d. Apply steady pressure for a few seconds at all areas of the gasket to verify proper adhesion. e. Peel the liner from the hinge gasket. f. Carefully position the gasket to the door frame above the hinge, and press firmly into place.

LED Motorcycle Power Box Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
This box requires the presence of a mounting plate secured to the motorcycle’s luggage rack. If the bike in question is not equipped with a mounting plate, one must be fabricated prior to installation of this box. Five mounting holes (.281″ dia.) are required to mount this box. If the motorcycle is already equipped with a mounting plate, it may be necessary to drill the 5 mounting holes required for this installation. Use the diagram shown to determine the precise location of these holes. 1. Position the box onto the mounting plate. Align the 5 vibration dampeners with the 5 mounting holes in the mounting plate. 2. Using the illustrations shown, secure the box to the mounting plate using the provided hardware. Note: Your luggage rack may already have the correct mounting holes drilled. Check the measurements below and if these holes already exist at the proper distance, remove any existing mounting hardware from the holes and secure the box with the supplied mounting hardware. 3. Place the box into its mounting position on the deck and secure it with the supplied mounting hardware as shown in the diagram. Wiring: Diagrams for optional equipment are found below. Refer to the diagram on the following page for general motorcycle box wiring information

HARLEY DAVIDSON SOFTAIL LEFT SIDE LEATHER TOOL BOX KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-04-2011

download
Installation While handling and installing tool box, be careful not to scratch surface. 1. See Service Parts Illustration. Install tool box (1) to mounting bracket (6) using button head screws (2) and washers (5). Screws (2) should be inserted through mounting holes on inside of tool box (1) and then inserted through bracket (6) holes and threaded into weld nuts attached to bracket. 2. Remove and save the two screws that secure left rear fender support to motorcycle frame. 3. Remove two bolts, nuts, and washers that secure debris deflector to motorcycle frame. This will allow you to move debris deflector out of the way when installing new passenger footpeg support bolt. Save hardware for reinstallation. 4. For 1990 to 1999 Softails: If tool box is being installed with passenger footpeg, remove the hex head bolt and left passenger footpeg. Retain footpeg and lockwasher for reinstallation. Discard bolt . If tool box is being installed without passenger footpeg, remove hex head bolt and left passenger footpeg. Discard footpeg. Retain bolt and lockwasher. For 2000 and later Softails: See page 3 . Remove footrest from clevis. Remove clevis from frame by removing cap screw from center of clevis. If tool box is installed with footpegs, keep all hardware. If toolbox is to be installed with footboards, discard hardware. 5. Slide top of mounting bracket (6) between rear fender support and frame. Align top holes in bracket with fender support holes. Align lower bracket hole with footpeg mounting hole in frame. Install the two screws, removed in Step 2, in fender support. Do not tighten screws at this time. 6. For 1990 to 1999 Softails: Place lockwasher retained in step 4 on footpeg support hex head bolt (3) from kit. CAUTION 1 of 3 For 2000 and later Softails with footpegs: Install kit 49352-00 according to instructions included in this kit. Footpeg must fold up at a 45°angle (from vertical) toward rear of motorcycle. This angle allows footpeg to fold up if, by accident, it strikes the ground surface when making a sharp turn. Failure to set footpeg to the proper fold-up angle could result in death or serious injury. 7. For 1990 to 1999 Softails: Position footpeg so it folds up and back at a 45°angle. Install bolt (3) from kit through frame, tool box bracket (6), and spacer (4), into footpeg, as shown. NOTE If vehicle is equipped with saddlebag support bracket, Part No. 90346-90 or 90346-94, position saddlebag support bracket between tool box bracket and spacer.

Incoming search terms:

SUZUKI GSX-R600 X-TRE Power Box Installation and Operation Manual

0

Filed Under (Suzuki) by admin on 10-02-2012

download
Installation Disclaimer: Do not attempt to install the product if you don’t have basic mechanical skills. HealTech Electronics Ltd. and its distributors shall not be liable for any loss or damage caused by improper installation. 1. Check the supplied parts: – X-TRE Power Box – Wiring harness – Yellow butt connectors, gel-filled (2 pcs) – Red tap connector, gel-filled – 4p jumper-plug – Cable ties (2+1 pcs) – Velcro strips – HealTech stickers (2+2 pcs) – Manual 2. Make sure the ignition key is in OFF position. Remove the seat. 3. Locate the ECM (Engine Control Module) under the seat. 4. Release the fuse box and relay switch to clean the area around the ECM connectors. 5. Locate the Black wire with thin dark Green stripe (B/G) , in the ECM connector. The wire position for different models is as follows: GSX-R600 K8-K9 GSX-R750 K8-K9 GSX-R1000 K7-K9 Black connector, pin no. 23 Middle row, 2nd wire from left to right at the back (wire) side of the connector ALL other years and models Black connector, pin no. 6 Top row, 6th wire from right to left at the back (wire) side of the connector

1994-2003 Suzuki GSXR750 and 1997-2004 Suzuki GSXR600 Superbike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 10-01-2011

download
Step 1: Identify the key components that complete our Superbike kit: You should have 2 lines (front kit), 1 double banjo bolt and 2 lower adapters. There are also a total of 7 washers. 5 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Inspect your brake system after every race. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. (See picture S4) Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt (see picture S5) is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, straight banjo (from right line), washer, 12-degree banjo (from left line), washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. ( See picture S6) Make sure that the 90-degree fittings on each caliper are pointing away from the bike just a little bit (see pictures S7 through S9 of calipers) . Thread each banjo end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using a zip-tie to bring the lines together about an inch above the lower triple clamp area. (Picture S10) Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with DOT 4-brake fluid is recommended.

Incoming search terms:

HARLEY DAVIDSON ELECTRA-GLO LIGHT POD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION NOTES Clean the controller mounting area and the areas where the light pods will be mounted with soap and water before beginning the installation, and allow to dry thoroughly. Remove debris, dirt and grime from the vehicle areas to be highlighted. Ambient temperature should be at least 50 °F (10 °C) for proper adhesion of the light pods and controller box to vehicle surfaces. Light pods should not be located closer than 2.5 inches (63.5 mm) from exhaust pipes or mufflers, and must have 1.5 inches (38.1 mm) clearance from engine cylinders and heads. Do not install light pods with the light source facing directly away from the vehicle. Installation should be done in a way that allows the light to be seen indirectly by reflecting from chrome or painted surfaces of the vehicle. Prepare the Motorcycle To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the owner’s manual and follow the instructions given to disconnect the battery cables, negative (-) cable first. NOTE For 2004 and later XL (Sportster®) models, the negative battery cable is most easily disconnected at the engine crankcase . Locate and Install the Controller NOTE Do not mount the controller box in a location where vehicle suspension travel could result in contact with the ON/OFF switch or dimmer control. Damage to the controller box will occur. 2. See Figure 2. Locate the controller box (10) on a flat surface that will allow the red (+) and black (-) leads to reach the battery terminals and the rider to access the controls (with the vehicle parked) and, if necessary, the in-line fuse holder (A). a. Test-fit the controller box to the selected surface before installation. Do not remove the adhesive backing until ready to attach the controller box. b. Clean the controller box mounting area with one of the included alcohol swabs. Allow to dry thoroughly. c. Remove the liner from the adhesive backing of the controller box. Carefully position the controller box to the surface, and press firmly into place. Hold the controller box in position with steady pressure for about one minute. Connect the Battery Cables NOTE Verify that the ignition/light key switch is in the OFF position before attaching the battery cables. 3. Verify that the ignition/key switch is turned to the OFF position. Apply a light coat of Harley-Davidson electrical contact lubricant (part number 99861-02), petroleum jelly or corrosion retardant material to the battery terminals. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 4. Refer to the owner’s manual and follow the instructions given to install first the vehicle’s positive (+) battery cable then the red (+) light pod controller lead ring terminal to the positive (+) battery terminal. Tighten to owner’s manual specifications. Install first the vehicle’s negative (-) battery cable then the black (-) light pod controller lead ring terminal to the negative (-) battery terminal. Tighten to owner’s manual specifications. Arrange the Electra-Glo Light Pods NOTES Electra-Glo light pods (1) can be installed in a variety of locations. They are best installed on a flat surface to provide indirect lighting illuminating mechanical features, vehicle finish or for ground effects. Refer to the notes at the beginning of the Installation section. 5. Select the area or lines of the motorcycle to highlight, and suitable locations for each light pod. DO NOT permanently affix the light pods at this time. Lightly tape the pods in place temporarily until the desired visual effect is achieved Verify clearance from movement of rubber mounted engine or other moving parts, heat sources, or chafe points

Incoming search terms:

SUZUKI MOTORCYCLES Gsxr 600, Gsxr 750, Gsxr 1000 teak the lead

0

Filed Under (Suzuki) by admin on 12-11-2010

download
The launch of the sixth generation of Gsxr marked a shift in Suzuki’s emphasis on two fronts. One, the Gsxr 1000 now took the upper hand in the development stakes. Historically, the Gsxr 750 led the march-arriving first, gaining the most recent technology, absorbing the lion’s share of corporate pride-but by 2003 the Gsxr 1000 was in the lead. Two, the Gsxr 1000 represents another, more subtle shift for Suzuki engineering, in which the designers-the lucky guys who get to clothe these amazing machines-have more freedom of expression. With this generation, the designs turned edgier, sharper, more aggressive looking than ever. What’s more, the Gsxr 1000 K3 would be the proving ground for a host of changes brought to the Gsxr 600 and Gsxr 750 for 2004. In fact, nearly every upgrade to the smaller bikes appeared on the Gsxr 1000 a year before. But the real impetus for driving the Gsxr 1000 to the head of development and, indeed, shortening its development cycle was competition both on the track and in the showroom. For the track, it was understood that Superbike racing would revert to allowing 1000 cc four-cylinder bikes in place of the 750s that had been the limit since 1982. In 2002, Yoshimura and Mat Mladin barely lost the AMA Superbike crown to Nicky Hayden aboard the Honda RC5!. But it would be the RC’s swan song of competitiveness with the change to 1000 cc fours. To keep speeds in check, the AMA Superbike rules would require 1000 cc fours to have some additional limitations compared to the twins and triples. For example, “Cylinder heads may be ported and machined, but altering of valve angles will not be permitted; aftermarket valves, springs, retainers, and other valve-train components will be permitted; valves must be stock size and same basic material as original equipment; aftermarket camshafts will be permitted, but earn lift and resulting valve lift must be no greater than stock. “In addition, the “stock crankshaft must be retained, The only allowable modifications are balancing, polishing of bearing surfaces and attachment of accessory drives. Homologated transmission gear sets (one optional set of ratios per approved model) will be permitted. Optional sets will be price-controlled and must be available to any legitimate AMA Superbike competitor. Homologated fuel-injection throttle-body assemblies (one optional type per approved model) and aftermarket airboxes will be permitted. Modifications to throttle bodies will not be permitted. Optional throttle bodies will be price-controlled and must be available to any legitimate AMA Superbike competitor.” The thinking was simple: keep the liter bikes from sucking through massive throttle bodies, and the horsepower might not (and, it was hoped, would not) go through the roof. In preparation for racing, Suzuki moto wanted to make a host of small changes to the Gsxr 1000, but its motivation was also to keep the bike at the forefront of open-class street bikes. Suzuki engineers knew that Honda and Kawasaki were readying all-new models-the CBR 954 RR and the ZX 9 R had long since been vanquished-and rumor had it that Yamaha was ready with yet another push with the R1.It was the right time to make alterations to the Gsxr 1000. Heading the list was, as one might expect, a revised engine.

Incoming search terms:

SUZUKI PUTS THE 'STYLE' IN LIFESTYLE WITH CUSTOM ACCESSORIES INSTALLATION

0

Filed Under (Suzuki) by admin on 14-02-2012

download
Suzuki Genuine Accessories are available for the all-new Equator midsize pickup truck, four-door SX4 Sport, five-door SX4 Crossover, XL7 midsize crossover and rugged Grand Vitara. The accessories can be purchased through local Suzuki dealers. Suzuki Equator  All-weather floor mats – Rubberized all-weather mats, ideal for keeping dirt, moisture and harsh debris from coming in contact with the vehicle’s carpet interior.  Bluetooth® module – The Suzuki-integrated hands-free Bluetooth phone system features a clean installation, fresh look and works with most Bluetooth-enabled mobile phones. Quality sound plays through the vehicle’s factory stereo and speakers, and the phone system automatically mutes the radio during phone calls. (Also available for SX4 Sport, SX4 Crossover, Grand Vitara and XL7.)  Body side moldings – Durable polyurethane molding set helps protect exterior paint from door dings and road rash.  Hood mask – Durable vinyl, custom-fit mask helps protect the front end of the vehicle from damage caused by minor road debris.  iPod® interface kit – Provides a seamless connection from an iPod to the vehicle’s radio and/or steering-wheel audio controls. (Also available for SX4 Sport, SX4 Crossover, Grand Vitara and XL7.)

Incoming search terms: